Motorola T6FB1 User Guide

DRAFT

Bluetooth®

Handsfree Headset

Get Connected in

4 Quick Steps

1 - CHARGE 2 - START BLUETOOTH FEATURE 3 - PAIR 4 - TEST AND USE

BEFORE YOU

BEGIN

Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions.

Take a moment before you get started to familiarize yourself with your new H5 Headset.

Volume Buttons

Call

Button

Indicator

Light

Earpiece Speaker

Microphone (inside earpiece)

Plug Motorola power

supply into charger port on charger base. The charger battery indicator light turns on ( ).

Insert headset snugly

into charger base.

The headset battery indicator light turns on ( ) to indicate the headset is charging. It may take up to 1 minute for the indicator light to turn on. When headset's battery is fully charged (about 2 hours), the headset battery indicator light turns off.

Note: Headset is not functional while charging.

CHARGE

Your Headset's Battery

Charger Plug

When charged,

remove headset from charger base.

Note: The charger base battery remains charging while plugged into the power supply.

Headset

Headset Battery Indicator Light

Charger Battery Indicator Light

START BLUETOOTH

FEATURE

Your Phone

Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone.

For most Motorola phones:

Press (

Bluetooth Link > Setup.

Scroll to Power.

Select Change.

Scroll to On.

Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn the feature off.

Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.

Menu) > Settings > Connection >

Before you can use your headset, you must pair (link) it with your phone.

Step A - PUT THE HEADSET IN PAIRING MODE

Indicator

Light

Ensure the headset is turned off (indicator

light not blinking).

Note: See "Turning On and Off" on the reverse side of this guide for details on turning off your headset.

Press and hold the Call button for 6 to 10

seconds. The indicator light will initially flash, but continue to hold down the button until the indicator light is steadily lit.

If the indicator light is flashing or not steadily lit when releasing the button, repeat both steps 1 and 2 on this page.

PAIR

Your Headset

Call Button

Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196

www.hellomoto.com 1-877-MOTOBLU 1-888-390-6456 (TTY/TDD United States for hearing impaired)

Guide Number: 6809495A89-O

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners.

PAIR

Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET

For most Motorola phones:

On your Motorola phone, press (

Settings > Connection > Bluetooth L in k > Handsfree > Look for D ev ic es .

The phone lists Bluetooth devices it finds.

Select Motorola H5.

Select OK or Yes to pair your headset with

your phone. Enter the passkey: 0000

Select OK.

When your headset successfully pairs with your phone, the indicator light changes from steadily lit to flashing.

Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.

CONTINUED

Your Phone

Menu) >

TEST AND USE

Your phone and headset are now paired and ready to make and receive calls. To make a call:

Place the headset in your ear. The eartip

should be inserted so that the headset feels comfortable and forms a seal in the ear.

On your phone, dial the number you want

to call and press the SEND key.

If your phone and headset are successfully

paired, you will hear ringing on the headset.

After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON.

USING YOUR H5

See

Features and

Functions Guide

on the reverse side

for information on

using your H5.

TROUBLESHOOTING

My phone doesn't find my headset.

Make sure the indicator light on your headset is on and steady when your phone is searching for devices (see step 3).

My headset worked before but now it's not working.

Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step

3).

Support. If you need more help, contact us at

1- 877-MOTOBLU.

FOR DETAILS ABOUT YOUR HANDSFREE DEVICE

See the user’s guide or visit us at www.hellomoto.com/bluetooth and click Support.

Bluetooth®

Handsfree Headset

IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side to

complete initial setup of

your H5.

TURNING ON AND OFF

To turn your headset on, press and hold

the Call button until the indicator light flashes.

To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off.

To conserve battery power, turn off your headset when you don't plan to use it for a while.

Indicator

Light

Call Button

INSTALLING EARTIP

Your headset is supplied with both flanged and foam eartips. To install these eartips:

FLANGED EARTIP:

Pull back largest

flange on eartip.

Twist eartip onto earpiece starting at an angle and pushing onto headset.

FOAM EARTIP:

Twist eartip onto earpiece starting at an angle and pushing onto headset.

WEARING HEADSET

FLANGED EARTIP:

Pull upward slightly on

top of your ear.

Place the earpiece

speaker into your ear.

The eartip should form a comfortable seal in your ear.

FOAM EARTIP:

Roll foam between thumb

and forefinger to compact.

Pull upward slightly on top of your ear.

Place the earpiece speaker into your ear and hold for 5 seconds while

The eartip should form a comfortable seal in your ear.

MAKING CALLS

Function Action

Make a voice dial call Tap the Call button and speak the name after the tone

End a call Tap the Call button

Receive a call Tap the Call button

Reject a call Press and hold the Call button until you hear a medium beep

Redial last call Press and hold the Call button until you hear a medium beep

Answer a second Press and hold the incoming call Call button until you hear a medium beep (places first call on hold)

Note: Your H5 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.

MAKING CALLS

Function Action

Toggle between two Press and hold active calls the Call button until you hear a medium beep

Join a 3-way call Press and hold both Volume buttons until you hear a medium beep

Put an active call on Press and hold the hold or resume a call Call button until you on hold hear a medium beep

Transfer a call from the Tap the Call button phone to the headset

Disable or enable the Press and hold indicator light both Volume buttons until you hear a low beep

Mute or unmute a call Tap both Volume buttons

Note: Some features are phone/network dependent.

CONTINUED

INDICATOR LIGHTS

Indicator lights provide information about your headset (and charger base) status.

Charger Base

Indicator Status

Charger Battery (On) Charging (Off) Charging complete

Headset Battery (On) Charging

(Off) Charging complete

Indicator Status

Off Power off On (steady) Pairing mode 10 rapid flashes Pairing successful Slow pulse Connected (on a call) Quick flash Standby (not on call)

Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.

Headset

AUDIO TONES

The audio tones provide information about your headset's status.

Audio Tone Headset Status

Single high tone when Volume at minimum pressing Volume button or maximum

Five rapid high tones Low battery repeated every 60 sec.

No audio indications; Out of range deteriorating quality

Ring tone Incoming call Single very high All calls ended

tone Single high tone Entering pairing mode Tapping Call button or

both Volume buttons Single medium tone Pressing Call button

or both Volume buttons Single low tone Pressing and holding

Call button or both Volume buttons

AUDIO TONES

Audio Tone Headset Status

Single high tone Phone network not repeated every 5 sec. available

Two ascending tones Mute enabled Two descending tones Mute disabled Four ascending tones Headset powering on Four descending tones Headset powering off

CONTINUED

VOLUME BUTTONS

Volume button orientation can be changed on your headset as follows:

Turn your headset off

Press both Call button and the Volume button

you want to assign as the "volume up" button until the indicator light flashes twice. The headset power turns on.