Congratulations on your purchase of a Motorola Product!
Product registration is an important step toward enjoying your new Motorola
Product. Registering helps us facilitate warranty service, and permits us to
contact you should your Motorola Product require an update or other service.
Registration is not required for warranty coverage. To register your product online, visit www.motorola.com/warranty/radios.
Please retain your original dated sales receipt for your records. For warranty
service of your Motorola Personal Communications Product you will need to
provide a copy of your dated sales receipt to confirm warranty status.
Introduction
1
Page 4
Motorola, the Stylized M Logo, and all other trademarks indicated as such herein
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio
The information provided in this document supersedes the general safety
information contained in user guides published prior to July 2000.
Transmit and Receive Procedure
Your two-way radio contains a transmitter and a receiver. To transmit (talk), you
must push the Push-to-Talk button; to receive (listen), release the Push-to-Talk
button.
Exposure to Radio Frequency Energy
Your Motorola radio is designed to comply with the following national and
international standards and guidelines regarding exposure of human beings to
radio frequency electromagnetic energy:
•United States Federal Communications Commission, Code of Federal
Regulations; 47 CFR part 2 sub-part J
•American National Standards Institute (ANSI) / Institute of Electrical and
Electronic Engineers (IEEE) C95. 1-1992
Safety and General Information
•Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
•International Commission on Non-Ionizing Radiation Protection (ICNIRP)
1998
4
Page 7
•Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to
Radio Frequency Electromagnetic Fields in the Frequency Range from 3 kHz
to 300 GHz, 1999
•Australian Communications Authority Radiocommunications
(Electromagnetic Radiation - Human Exposure) Standard 2001 (applicable to
wireless phones only)
To assure optimal radio performance and make sure human exposure to radio
frequency electromagnetic energy is within the guidelines set forth in the above
standards, always adhere to the following procedures:
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the radio and may violate
FCC regulations.
DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna
affects the effective range.
Two-Way Radio Operation
When using your radio as a traditional two-way radio, hold the radio
in a vertical position with the microphone one to two inches (2.5
to 5 cm) away from the lips.
Safety and General Information
5
Page 8
To control your exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the following
procedure:
•Transmit no more than 50% of the time.
•To transmit (talk), push the Push-to-Talk (PTT) button.
•To receive calls, release the PTT button.
Transmitting 50% of the time, or less, is important because the radio generates
measurable RF energy exposure only when transmitting (in terms of measuring
standards compliance).
Body-Worn Operation
To maintain compliance with FCC/Health Canada RF exposure guidelines, if you
wear a radio on your body when transmitting, always place the radio in a
Motorola-supplied or approved clip, holder, holster, case, or body harness for this
product. Use of non-Motorola-approved accessories may exceed FCC/Health
Canada RF exposure guidelines. If you do not use one of the Motorola-supplied
or approved body-worn accessories, and are not using the radio held in the
normal use position, ensure the radioand its antenna are at least one inch (2.5 cm) from your body when transmitting.
Safety and General Information
Data Operation
If applicable, when using any data feature of the radio with or without an
accessory cable, position the radioand its antenna at least one inch (2.5 cm)
from the body.
6
Page 9
Approved Accessories
For a list of approved Motorola accessories visit our website at www.mot.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your
radio in any facility where posted notices instruct you to do so. Hospitals or health
care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use
of a radio must be in accordance with applicable regulations per airline crew
instructions.
Medical Devices
Pacemakers
The Advanced Medical Technology Association recommends that a minimum
separation of 6 inches (15 centimeters) be maintained between a handheld
wireless radio and a pacemaker. These recommendations are consistent with the
independent research by, and recommendations of the U.S. Food and Drug
Administration.
Safety and General Information
7
Page 10
Persons with pacemakers should:
•ALWAYS keep the radio more than six inches (15 centimeters) from their
pacemaker when the radio is turned ON.
•not carry the radio in the breast pocket.
•use the ear opposite the pacemaker to minimize the potential for interference.
•turn the radio OFF immediately if you have any reason to suspect that
interference is taking place.
Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid manufacturer to
discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your
device to determine if it is adequately shielded from RF energy. Your physician
may be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations on the use of radios in the area where you drive.
Always obey them.
Safety and General Information
When using your radio while driving, please:
•Give full attention to driving and to the road.
•Use hands-free operation, if available.
•Pull off the road and park before making or answering a call if driving
8
conditions so require.
Page 11
Operational Warnings
For Vehicles with an Air Bag
Do not place a portable radio in the area over an air bag or in the air bag
deployment area. Air bags inflate with great force. If a portable radio is placed in
the air bag deployment area and the air bag inflates, the radio may be propelled
with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere, unless it is a radio type especially qualified for use in such areas as
“Intrinsically Safe.” Do not remove, install, or charge batteries in such areas.
Sparks in a potentially explosive atmosphere can cause an explosion or fire
resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to above
include fueling areas such as below decks on boats, fuel or chemical
transfer or storage facilities, areas where the air contains chemicals or
particles, such as grain, dust or metal powders, and any other area
where you would normally be advised to turn off your vehicle engine.
Areas with potentially explosive atmospheres are often but not always
posted.
Safety and General Information
9
Page 12
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when
you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn
off two-way radio.” Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a
conductive material such as jewelry, keys, or beaded chains touch exposed
terminals. The conductive material may complete an electrical circuit (short
circuit) and become quite hot. Exercise care in handling any charged battery,
particularly when placing it inside a pocket, purse, or other container with metal
objects.
Safety and General Information
10
Page 13
Charger Safety Instructions
Before using the battery charger, read all instructions and cautionary markings on
the:
1. battery
2. battery charger, and
3. radio using the battery.
Caution: To reduce the risk of injury, charge only the rechargeable batteries
listed below. Other types of batteries may burst, causing personal
injury and damage.
Single-Unit Charger
Kit NumberDescription
NTN9393110V - NiMH Charging Adapter
Batteries
Kit Number
NTN9395550 mAHNiMH
Capacity in
milliampere-hour mAH
Composition
Charger Safety Instructions
11
Page 14
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate the charger if it has received a sharp blow, or has been
dropped or damaged in any way.
3. Do not disassemble the charger if it has received a sharp blow, or has been
dropped or damaged in any way.
4. Never alter the AC cord or plug provided with the unit. If plug will not fit the
outlet, have proper outlet installed by a qualified electrician. An improper
condition can result in a risk of electric shock.
5. To reduce risk of damage to cord or plug, pull the plug rather than the cord
when disconnecting charger from AC receptacle.
6. To reduce the risk of electric shock, unplug the charger from the outlet before
attempting any maintenance or cleaning.
7. Use of an attachment not recommended or sold by Motorola may result in a
risk of fire, electric shock, or personal injury.
8. Make sure that the cord is located so that it will not be stepped on, tripped
over, or subjected to damage or stress.
Charger Safety Instructions
12
Page 15
9. An extension cord should not be used unless absolutely necessary. Use of
an improper extension cord could result in a risk of fire and/or electric shock.
If an extension cord must be used, make sure:
• That the pins on the plug of the extension cord are the same number, size
and shape as those on the plug of the charger.
• That the extension cord is properly wired and in good electrical condition,
and
• That the cord size is18 AWG for lengths up to 100 feet, and 16 AWG for
lengths up to 150 feet.
10. The supply cord of this charger cannot be replaced. If the cord is damaged,
call Motorola Customer Care Center at 1-800-353-2729 in the USA or
1-888-390-6456 TTY (Text Telephone).
Charger Safety Instructions
13
Page 16
FCC Licensing Information
Your Motorola radio operates on General Mobile Radio Service (GMRS)
frequencies and is subject to the Rules and Regulations of the Federal
Communications Commission (FCC). The FCC requires that all operators using
General Mobile Radio Service (GMRS) frequencies obtain a radio license before
operating their equipment. To obtain the FCC licensing forms, please request
Forms 605
questions, please use the following contact information.
Contact the Fax-On-
Demand system at:
Changes or modifications not expressly approved by Motorola may void the
user’s authority granted by the FCC to operate this radio and should not be made.
To comply with FCC requirements, transmitter adjustments should be made only
FCC Licensing Information
by or under the supervision of a person certified as technically qualified to perform
transmitter maintenance and repairs in the private land mobile and fixed services
as certified by an organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio could violate FCC
rules. Note: Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
14
and 159. If you want to have the document faxed, mailed, or have
Faxed
Call the FCC forms
1-202-418-01771-800-418-FORM
Mailed
hotline at:
1-800-418-3676
Questions
regarding FCC license
Contact the FCC at:
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
Page 17
Getting Started
:
Control Buttons and Basic Operation
Indicator Light
Use P (Power) to:
- Turn power on/off
Use
\ to:
- Scroll through menus
- Lock the keypad (when
held down and not in a
menu)
- Exit the menu (when held
down while in a menu)
Use
((Call)
- Transmit call tone
se M to:
Talk on the radio
Exit the menu (when briefly
pressed while in a menu)
to:
UseQto:
- Turn on backlight
(short press).
- Press and hold to
switch between
weather mode and
two-way mode.
Use
[ and ] to:
- Adjust volume
- Scroll through menu
settings
Use
(short press)
(Scan/Monitor) to
)
- Turn scan on/off
- Monitor the channel &
check signal strength
(long press)
Microphone
Getting Started
15
Page 18
Installing the Batteries
Your radio uses 3 AA Alkaline batteries or a rechargeable Nickel-Metal Hydride
(NiMH) battery (sold separately). A NiMH battery upgrade kit (56319) is also
available. Call 1-800-353-2729 in the USA for a dealer nearest you.
1. If the radio is on, turn it off by pressing and holding P.
2. Push latch up until it clicks.
3. Lift back cover off
4. Remove and replace batteries so the + marking matches the one in the compartment or the NiMH charge contacts are facing out toward the battery
door.
5. Hook back cover on the hinges.
6. Close the battery door, pressing lightly until the latch clicks and returns to its
original position.
Getting Started
Latch
16
Page 19
Battery Meter
The battery meter on the top-left corner of the display shows how much battery
power you have. It shows d (full), b (two-thirds full), c (one-third full),
or a (empty). When the battery is low (c), the radio beeps every 10 minutes
indicating it’s time to change or charge them.
Setting the Battery Type
This feature is used to set the battery meter to recognize and properly display the
power usage for either alkaline or rechargeable batteries.
To set the battery type, press \ until d is displayed. Press [
or ] until your choice of A (alkaline) or n (NiMH or NiCad) is
displayed, then press M to set.
Getting Started
17
Page 20
Charging the NiMH Battery (Optional Accessory)
Charge the NiMH battery overnight (16 hours) before using it for the first time. It
will only need up to four hours of charging thereafter.
Charger
Battery
Adapter
Cover
Charger
Or
Light Indicator
1. If the radio is on, turn it off by pressing and holding P, or place the NiMH
battery in the charger adapter cover.
Getting Started
2. At the contacts on the back of the radio (or if you are charging just the battery, at the battery contacts), position the charger so the large hook on the
end of the charger is over the large slot on the battery door, or if you are
charging the battery by itself, on the large slot on the charger adapter cover.
3. Place the small hook on the other end of the charger over the small slot and
snap it into place.
4. Plug in the charger.
18
Page 21
Charging Status
The light indicator shows the charging status when the charger is connected to
the radio, the NiMH battery, or the charging dock.
Light Indicator
Color
Charging Status and Description
Charging Level
Complete
Solid RedRapid chargingUp to 90%
Flashing GreenTop-off charging90% to 100%
Solid GreenCharging complete100%
Flashing Red
Battery is faulty. If flashing red continues for
-
more than one minute, the battery is faulty
and should be replaced.
Flashing YellowStandby - Battery waiting to charge.
-
Temperature out of range for charging; must
be between 5
o
to 40o C or 41o to 104o F
Note: When moving between hot and cold environments, do not charge the
battery until the battery temperature acclimates (usually about 20
minutes). When charging the battery by itself, remove the charger from
the charger adapter cover before inserting and/or removing the battery
from the charger adapter cover.
Getting Started
19
Page 22
Charging Dock (Optional Accessory)
The charging dock provides drop-in charging convenience. The charging dock
can be mounted or placed on any flat surface (such as a wall or workbench) and
turns your radio into a stationary intercom while keeping it charged and ready for
any adventure. To mount the charging dock:
1. Wrap the power cord under the charging dock.
Use the cutouts to hold the cord in place.
2. Attach using two #6 x ¾” screws for the
mounting surface.
20
Getting Started
Cutouts
Page 23
3. Position the charger with the hook on the light
indicator end over the left slot.
4. Snap the hook on the cord end into the right slot,
clamping the charger onto the charging dock
contacts.
5. Plug in the charger.
6. Place the radio, or the NiMH battery in the
charger adapter cover, into the charging dock
until you hear a click.
7. When the light indicator turns solid green, the
battery is fully charged.
Charging Dock
Charger
Light Indicator
Getting Started
21
Page 24
Belt Clip
-
Squeeze the top and
bottom of the clip to attach
or detach the clip from the radio.
Note: The belt clip holds the
radio while being worn
on your belt. It was
designed for your
convenience and is not
meant to secure your radio
under all circumstances.
For high activity
Getting Started
environments, an accessory
carry case is more
appropriate to secure the
radio.
NiMH Battery Charging Contacts
22
When using audio
accessories, ensure
that they are plugged
in before you turn on
the radio *
*Motorola recommends
that the volume
level is kept at a
comfortable listening
level when using audio
000884-O
accessories.
Page 25
Turning On Your Radio
Normal Menu Mode
Press and hold
image. The red light above the
Simple Menu Mode
Press and hold
only six images.
The red light above the
to only the Channel, Code, and Call Tone menus.
P. The radio beeps and the screen temporarily displays every
button flashes every three seconds.
P
P and \. The radio beeps and the screen temporarily displays
button flashes every three seconds. You have access
P
Normal Menu ModeSimple Menu Mode
Getting Started
23
Page 26
Your Radio’s Display
24
Lock Set
Battery Meter
Channel Scan On
QuieT6000™
Eavesdrop Reducer
Volume Control
Signal Strength
Indicator
Getting Started
VibraCall® Alert On
Interference Eliminator
Code
Automatic Power Off
Hands-free Use with
Accessories (VOX)
Transmit Call Tone\
Call Tone Received
Channel Indicator
Ring Alert On
Weather On
Page 27
Volu me
You can set the volume whenever you are not using a menu. Press
or ] until it’s just right. The display shows
[
volume setting (
being the highest volume.
Backlight
Your radio has a backlight that turns on automatically any time you press a button.
The backlight turns off automatically four seconds after you last pressed a button.
You can also illuminate your display by pressing
Turning Off Your Radio
To turn off your radio press and hold P for one second. The radio beeps and the
display goes blank.
)
1
with
to
20
1
being
the lowest volume and
V and the current
20
.
o
R
5
Getting Started
25
Page 28
Setting the Channel
To Set the Channel
The channel is the radio frequency wave your radio uses to
transmit. Refer to the Frequency and Code Charts beginning on
page 46 for channel and code choices.l
1. Press \ once. The channel number begins to blink.
2. Press [ or ] to set the channel.
3. Go to the next menu or wait 10 seconds to save the channel setting. To
quickly exit the menu and go back to the first display screen, press M.
The red indicator light above the P button flashes quickly whenever the channel
is in use. Keep scrolling until you find a clear channel.
Setting the Channel
26
Page 29
Talking and Listening
Press and hold M and talk two-to-three inches away from the microphone. When
you’re finished, just release M (press and hold to talk, release to listen). While
transmitting, the red indicator light above the P button glows.
Note: The microphone is located under the ) button. Be careful not to cover it
when you press M.
Talking Range
Optimal Range
Flat, open areas
Medium Range
Buildings or trees
Minimal Range
Dense foliage or
mountains
Buildings or vehicles
Talking and Listening
27
Page 30
Special Features
The following table lists features you can set by pressing and holding specific key
combinations while turning on your radio.
Turns audible button beeps and local audible
call tones on or off.
Turns Talk Confirmation Tone on or off.
Turns on Simple Menu mode. See page 44.
Turns on or off the QuieT6000 (Setting
feature. See page 37.
To
1)
Page 31
Almost all other settings for your radio are done using the same basic key
sequence. Use your radio’s
you want them. All the features that work using this key sequence are described
on the following pages.
PressDisplayThen Press
and[ or] to select and set features the way
\
\
Interference Eliminator Code
The interference eliminator codes help minimize interference and
unwanted messages by providing you with a choice of code
combinations. Refer to the Frequency and Code Charts beginning
on page 46 for channel and code choices.
1. Press \ twice until the code number display begins to blink.
2. Press [ or ] to set the code, press M to save the code setting.
3. To hear everyone on your channel, select code
Note: Carrier squelch (0) disables interference eliminator codes. This allows
the icon representing
the feature you want
you to monitor all activity on the channel you are using.
[ or ] to select the feature, then press M
or wait ten seconds (60 seconds for Simple
Menu mode) to save the setting or press
and hold \.
0.
Special Features
29
Page 32
To specify a different code for each channel:
1. Press \ and then press [ or ] to select the channel.
2. Press \ again, then press [ or ] to select a code.
3. Press M to exit the menu and to save the channel and code combination.
4. To set another channel and code combination, repeat these steps.
Monitor/Signal Strength Indicator
The ) button allows you to listen to all activity on a channel (open squelch) to tell
whether the channel is currently in use.
This
button
also helps you determine when
a radio is moving out of range.
To check for channel activity, press and hold ). You’ll hear static if the channel is
clear and w will display. Don’t transmit if you hear conversation. To avoid
interrupted conversation, wait until the channel is clear or switch to another
channel.
Special Features
The w helps you determine when a radio is moving out of range
by displaying a receive signal-strength value next to the w while
you press and hold ). This value from
(strongest) indicates the relative strength of the incoming signal.
Note: Obstacles that block the signal path may affect the
1 (weakest) through 6
Signal Strength
Indicator
strength of the incoming signal.
30
6
Page 33
Setting Sensitivity Level
The sensitivity level allows you to compensate for background noise when using
an accessory. If you are not using an accessory, the sensitivity level adjusts your
microphone’s sensitivity. By adjusting the sensitivity level up or down, you can
minimize the chance of unintended noises triggering a transmission, or increase
the microphone’s ability to pick up quiet voices
To set the sensitivity level, press \ until g and a value from
through
•High (
•Medium (
•Low (
When you connect a VOX accessory, the radio is automatically set to your last
sensitivity level.
When using an iVOX accessory, there are 5 sensitivity levels to choose from,
1 (lowest) to 5 (highest).
3 is displayed, then select:
3) for quiet environments
2) for most environments
1) for noisy environments
1
1
g
Special Features
31
Page 34
Alerts
Alerts allow members of your group to notify each other that they want to talk.
Alerts can be audible, visual, or vibrating.
You can also determine how your radio alerts you when you’re receiving: vibrate,
ring, both, or none. Your radio vibrates and/or ring only the first time you receive
a transmission or call. It does not ring or vibrate again until 30 seconds of inactivity
have elapsed.
Call Tone and Call Display
Your radio can transmit different call tones to other radios in your group so you
can alert them that you want to talk to them. Each person in the group can have
an individual call tone.
Alerts
To set your call tone:
1. Press \ until ^ is displayed.
2. Press [ or ] to scroll through the available call tones. The
radio plays a sample of each tone as you scroll through
them.
3. To use your call tone, press ( to transmit it to others. The ^icon is displayed
next to the channel number.
32
Page 35
Ring Only
The ring feature rings the call tone you’ve selected to notify you
of two-way radio reception. When you set this feature, the radio
produces the call tone, after 30 seconds of inactivity, each time
you receive a two-way radio transmission.
To set the Ring feature, press \ until B is displayed and then
press [ or ] to select n or Y.
If you select Y, B remains on the display after you exit the menu.
Ring and/or VibraCall
Your radio features Ring and/or VibraCall
®
Alert
®
alert, a vibrating alert to notify you of
two-way radio reception in noisy environments.
To set Ring and/or VibraCall
®
alert, press \ until B and/or i is displayed then
press [ or ] to select the desired setting.
Alerts
33
Page 36
Setting
Display Within
Menu
Function
34
Alerts
-
1i
2
3
B
Bi
Your radio doesn’t sound an alert, just the
actual transmission. You still hear the talk
confirmation tone (if activated).
Your radio vibrates to alert you.
Your radio rings your call tone when you
receive a call.
Your radio vibrates and rings your call tone
when receiving.
Page 37
Talk Confirmation Tone
Whenever you turn on the talk confirmation tone feature, your two-way radio
transmits a unique tone when you finish transmitting. It’s like saying “Roger” or
“Over” and lets others know you’re finished talking. If you don’t hear the talk
confirmation tone, you can enable it by pressing and holding ] as you turn on
your radio. Now, whenever you release the M button, you let your friends know
you’re finished talking by transmitting a tone. To disable the talk confirmation tone
feature, turn your radio off and then back on while pressing and holding ].
Button Beeps
Every time you press a button on your radio, it beeps unless you turn Button
Beeps off. To turn Button Beeps off, turn your radio on while you press and hold
. To turn Button Beeps back on, turn the radio off and then back on again while
[
you press and hold [.
When Button Beeps are turned off, you won’t hear call tones that you send.
Alerts
35
Page 38
Privacy
Eavesdrop Reducer
Your radio has the Eavesdrop Reducer feature, a scramble code that
makes your transmissions sound garbled to anyone listening without the
same scramble code. It doesn’t guarantee secrecy, but it adds an extra
layer of privacy. Don’t forget -- all the radios have to be set to the same
Eavesdrop Reducer code for the transmissions to be clear.
To turn the Eavesdrop Reducer feature on, press \ until e is displayed, then
select scramble code 1, 2, or
After you exit the menu, the display shows e.
To turn the Eavesdrop Reducer feature off, press \ until e is displayed, then
Alerts
select
-. After you exit the menu, edisappears from the display.
36
3.
Page 39
QuieT6000™
The QuieT6000
TM
function helps ensure uninterrupted communication among
Motorola Talkabout T6000 series radios - it helps prevent you from hearing
transmissions from other radios. However, other radios can hear you.
To turn the QuieT6000 function on or off, press \ until F is displayed. Then
select one of the following settings:
SettingDisplayFunction
-
38
1
QuieT6000 is turned off.
QuieT6000 is turned on, but is suspended while
scanning.
2
QuieT6000 is turned on, including while scanning.
You can also turn the QuieT6000
pressing and holding
while you turn on your radio.
(
function on (Setting 1) or off (Setting -) by
Alerts
37
Page 40
If your radio has QuieT6000 on and want to talk to others in your group who also
have QuieT6000 on, you must first transmit a call tone before talking to them.
When the call tone is transmitted, ^ is displayed on the other radios with the same
channel, interference eliminator code, scramble code, and QuieT6000 on, letting
them know that you want to talk to them. Those radios can then receive and
transmit until 30 seconds of inactivity occurs, which resets the QuieT6000
function. While QuieT6000 is on, F is displayed. However, during the 30
seconds of inactivity, F flashes.
Unique Situations
QuieT6000 can also keep your radio quiet when you are in a situation where noise
can be disruptive, such as when you are in a movie theater or out hunting. Set
QuieT6000 to either 1 or 2 and set your radio’s alert to 1 (VibraCall
Alerts
Now when you receive a call from radio, your radio vibrates while the ^ displays
®
alert only).
on the screen. The ^ icon remains on the screen until you press any button. Only
then can you receive and transmit to those radios until 30 seconds of inactivity
occurs and the QuieT6000 function resets.
38
Page 41
Weather
Your radio can tune into broadcasts by the United States National Oceanic and
Atmospheric Administration (NOAA) Weather Radio and Environment Canada
Weatheradio.
You can listen to a weather channel or set your radio to alert you to emergency
weather broadcasts that interrupt routine broadcasts.
Both NOAA and Environment Canada have transmitters located throughout the
United States and Canada, respectively. These transmitters broadcast watches,
forecasts, and other information 24 hours a day.
Note: Service may not be available in all areas. Check with your local weather
office for frequency and details, or visit www.nws.noaa.gov/nwr in the US
or www.msc-smc.ec.gc.ca/cd/factsheets/wxradio in Canada. The use of
the NOAA logo does not provide an endorsement or implied
endorsement by NOAA's National Weather Service nor does the use of
the Weatheradio logo provide an endorsement or implied endorsement
by Environment Canada.
Whenever you listen to a weather channel, you cannot use your radio for two-way
communications. However, a weather alert will notify you while the radio is in twoway mode (if you have enabled weather alert) and the radio is on but not
transmitting or receiving.
Weather
39
Page 42
Turning On Weather Channel Reception
To turn on weather channel reception, press and hold
return to two-way mode, press and hold
Setting the Weather Channel
Your radio receives seven frequencies. See the Frequency and
Code Charts beginning on page 46 for a complete list.
After turning on the weather broadcast, press
channel display blinking. Press [ or ] to select the strongest
channel.
As with two-way radio reception, weather channel reception depends on how
close you are to a transmitter and whether you are indoors or outdoors. Also,
because weather channels are transmitted without codes, they may contain static
Weather
or noise.
40
Ro again.
\ to start the
Ro. To turn it off and
Page 43
Setting the Weather Alert
If you set the weather alert and switch back to two-way mode, o
is displayed.
Whenever NOAA or Environment Canada transmit an emergency weather
broadcast on the selected channel, your radio alerts you using the selected alert
mode, ring B or vibrate i, and switches to the selected weather channel. If your
radio is in weather mode, you will receive a weather alert only on the selected
channel.
To set weather alerts, switch to weather mode, press \ twice,
and press [ or ] to select
Y (on).
Note: The Talkabout T6250 two-way radio is designed to be
primarily a two-way radios with added features such as
Weather Alert. The radio uses the same circuitry for both
two-way radio and weather alert receptions. Therefore, you can miss a
weather alert while you are in two-way communication (either
transmitting or receiving). To ensure that you do not miss a weather alert,
leave the radio in the Weather Mode.
Weather
41
Page 44
Other Important Features
Lock
To avoid accidentally changing radio operation, the Lock feature locks the Menu,
Volume Control, Weather, and Scan functions, meaning that you can only turn the
two-way radio on and off, transmit, and monitor.
You can make sure your menu settings won’t be changed
accidentally. Just turn on lock by pressing
Now you’ll see the f icon.
To turn Lock off, press
Note: If your radio is in two-way mode and Weather Alert is
enabled, an emergency broadcast on the selected channel
will switch the radio to that weather channel.
Scanning
By using Scanning h, you can monitor channels and codes for transmissions
and lock in on the one that interests you. More importantly, you can find
Other Important Features
someone in your group who has accidentally changed channels and is talking
during your scan. You don’t have to set a new channel or code, the radio just
resets itself temporarily to that channel and code and you can start talking.
To start scanning, briefly press
displays
channel activity, it stops on that channel and displays its channel and code. You
42
h and begins to scroll through channels. When the radio detects
\ again for three seconds.
) (Scan/Monitor). Your channel/code screen
for three seconds.
\
Lock On
Page 45
can talk to the person(s) transmitting without having to switch channels by
pressing
scanning, the radio will transmit on the channel you selected before you activated
Scan. If no transmission occurs within five seconds, scanning will resume.
If you want to scan channels without interference eliminator codes, change the
code for your set channel to
Scan List Editing
You can select the channels you want to scan by putting those channels in a scan
list. To edit the scan list, press
through the list of available channels. When you see a channel you want to add
to the list, press
it.
Auto Power Off
You can program your radio to turn itself off after a certain period of
inactivity. This helps save battery life.
To set the automatic power off feature, press \ until O is
displayed. Press [ or ] to set the number of hours
power shuts off.
.
To stop scanning, briefly press ). If you press
M
0 before you briefly press
\ until h is displayed. Press ] or [ to scroll
until Y is displayed to add it or until n is displayed to to remove
)
while the radio is
M
.
)
1 - 8, after which
O
8
Other Important Features
43
Page 46
After you exit the menu, O displays on the screen when the automatic power off
feature has been activated. Five minutes before the radio shuts off, an alert beep
sounds. Another alert beep will sound once per minute and O will flash
continuously during those five minutes. Select - to turn off the automatic power
off feature.
Reset
You can reset your radio’s menu settings to the factory settings by turning it on
while pressing and holding M and \ or
Simple Menu
Simple Menu allows you to limit the number of menus displayed (Channel, Code,
and Call Tones) to allow for simpler radio operation. The Scan and Weather
features, along with most of the radio turn-on sequences (see page 23), are also
disabled to prevent accidentally changing the radio’s mode of operation.
If you want the radios in your group to keep the same settings that you have on
your radio, press \ as you turn each radio on. Simple Menu increases the menu
time-out to 60 seconds. To turn off Simple Menu, press \ as you turn on the
Other Important Features
radio.
If you want to set up Simple Menu for inexperienced users, without advanced
features activated such as Eavesdrop Reducer and QuieT6000, reset their radios
to the original factory settings by pressing
while turning on their radios. Then activate Simple Menu by turning their radios
off and then back on while pressing
44
\
and
M
and
)
.
.
)
or by pressing
M
M
and
\
Page 47
Accessories
Make sure the radio is turned off before plugging audio accessories into the
accessory port. Before you place an accessory on your head or in your ear, turn
the volume down. After placing the accessory on your head or in your ear, adjust
the volume by pressing [ or
Hands-Free Use (VOX) With Accessories
VOX allows you to transmit “hands-free” by talking while using VOX accessories
connected to the radio.
To set VOX, plug in your accessory before you turn on your radio. When you turn
on your radio, flashing g is displayed. Your radio now detects your voice and
transmit every time you talk. When you transmit using a VOX headset, you will
hear yourself talking through the accessory speaker. This lets you know VOX is
working.
Press M to turn off VOX and return to the regular way of transmitting. The g icon
disappears. To reset VOX use, turn your radio off and then back on with your
accessory plugged in.
Hands-Free Use Without Accessories (iVOX)
You can use the radio’s VOX feature to transmit handsfree without a connected
VOX accessory. Press \ until g flashes. Press ] or [ until Y (on) is
displayed, then press M twice. Your radio transmits every time you speak.
Note: There is a short delay when you start talking before the transmitter turns
on.
.
]
Accessories
45
Page 48
Frequency and Code Charts
The charts on these pages provide frequency and code compatibility information.
These charts are useful when using Motorola Talkabout two-way radios with other
FRS radios.
Reposition or replace alkaline batteries.
Recharge or replace NiMH battery.
Make sure M is completely pressed as you transmit.
Reposition, replace, or recharge batteries.
Confirm interference eliminator code is set.
Shared channel or interference eliminator code may be in
use, try another.
Eavesdrop Reducer code is on, or setting does not match
other radios’ settings; all radios must use the same
Eavesdrop Reducer code.
Steel and/or concrete structures, heavy foliage, use in
buildings or vehicles decrease range. Check for clear line of
sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt
decreases range. Change location of radio.
Troubleshooting
51
Page 54
SymptomTry This:
Message not
received
Troubleshooting
52
Confirm radios have the same channel and interference
eliminator code settings.
Make sure M
is NOT being pressed while trying to listen.
Reposition, replace, or recharge batteries.
If QuieT6000 feature is on, transmit call tone before talking.
If QuieT6000 feature is on, with only VibraCall
®
alert
selected, a received call must be acknowledged by pressing
any button (or a VOX activation) before the radio can receive
any incoming transmissions.
Obstructions and operating indoors, or in vehicles, may
interfere -- change location.
Verify that the radio is not in Scan mode.
Eavesdrop Reducer code is on, or setting does not match
other radios; all radios must use the same Eavesdrop
Reducer code.
Page 55
SymptomTry This:
Heavy static or
interference
Channel and/or
code locked
Cannot access
all menus
or
Cannot display
desired icon
Other radios not
receiving your
transmissions
Low batteries
Radios are too close, they must be at least five feet apart.
Radios are too far apart or obstacles interfering with
transmission. Talk range is up to two miles depending on
terrain and conditions.
Make sure menu is unlocked. Unlock by pressing \ for
three seconds.
Verify whether Simple Menu is activated. Disable Simple
Menu by pressing \ while turning on the radio.
QuieT6000 mode is set. Press ( to talk to members of your
party or turn QuieT6000 off.
Replace alkaline batteries. Recharge or replace NiMH
battery. Extreme operating temperatures affect battery life.
Troubleshooting
53
Page 56
SymptomTry This:
Low battery
meter reading
although new
batteries are
installed
Charger LED
double flashing
Cannot activate
VOX
Troubleshooting
54
Verify that the radio is set to the correct battery type. See
page 17.
Charger not properly positioned. Reposition charger and
ensure it is firmly clamped to the radio, battery, or charging
dock.
Battery power is very low; battery is charging up slowly before
it starts to quick charge.
Feature not set and on.
Page 57
Motorola Limited Warranty
for the United States and Canada
What Does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc. warrants its telephones,
pagers, and consumer and professional two-way radios (excluding commercial,
government or industrial radios) that operate via Family Radio Service or General
Mobile Radio Service, Motorola-branded or certified accessories sold for use with
these Products (“Accessories”) and Motorola software contained on CD-ROMs or
other tangible media and sold for use with these Products (“Software”) to be free
from defects in materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a consumer's exclusive remedy,
and applies as follows to new Motorola Products, Accessories and Software
purchased by consumers in the United States or Canada, which are accompanied
by this written warranty:
Products and Accessories
Products CoveredLength of Coverage
Products and Accessories as
defined above, unless otherwise
provided for below.
One (1) year from the date of purchase
by the first consumer purchaser of the
product unless otherwise provided for
below.
Motorola Limited Warranty
55
Page 58
Products CoveredLength of Coverage
Decorative Accessories and Cases.
Decorative covers, bezels,
PhoneWrap™ covers and cases.
Monaural Headsets. Ear buds and
boom headsets that transmit mono
sound through a wired connection.
Consumer and Professional
Two-Way Radio Accessories.
Products and Accessories that are
Repaired or Replaced.
Exclusions
Motorola Limited Warranty
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts
due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their
rated capacity and batteries that leak are covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper operation,
storage, misuse or abuse, accident or neglect, such as physical damage (cracks,
56
Limited lifetime warranty for the
lifetime of ownership by the first
consumer purchaser of the product.
Limited lifetime warranty for the
lifetime of ownership by the first
consumer purchaser of the product.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
The balance of the original warranty
or for ninety (90) days from the date
returned to the consumer, whichever is
longer.
Page 59
scratches, etc.) to the surface of the product resulting from misuse; (b) contact
with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the
like, extreme heat, or food; (c) use of the Products or Accessories for commercial
purposes or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of Motorola, are excluded from
coverage.
Use of Non-Motorola Products and Accessories. Defects or damage that
result from the use of Non-Motorola branded or certified Products, Accessories,
Software or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages resulting from
service, testing, adjustment, installation, maintenance, alteration, or modification
in any way by someone other than Motorola, or its authorized service centers, are
excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or date tags
that have been removed, altered or obliterated; (b) broken seals or that show
evidence of tampering; (c) mismatched board serial numbers; or
(d) nonconforming or non-Motorola housings, or parts, are excluded form
coverage.
Communication Services. Defects, damages, or the failure of Products,
Accessories or Software due to any communication service or signal you may
subscribe to or use with the Products Accessories or Software is excluded from
coverage.
Motorola Limited Warranty
57
Page 60
Software
Products CoveredLength of Coverage
Software. Applies only to physical
defects in the media that embodies the
copy of the software (e.g. CD-ROM, or
floppy disk).
Exclusions
Software Embodied in Physical Media. No warranty is made that the software
will meet your requirements or will work in combination with any hardware or
software applications provided by third parties, that the operation of the software
products will be uninterrupted or error free, or that all defects in the software
products will be corrected.
Software NOT Embodied in Physical Media. Software that is not embodied in
physical media (e.g. software that is downloaded from the internet), is provided
“as is” and without warranty.
Motorola Limited Warranty
Who is Covered?
This warranty extends only to the first consumer purchaser, and is not
transferable.
58
Ninety (90) days from the date of
purchase.
Page 61
What Will Motorola Do?
Motorola, at its option, will at no charge repair, replace or refund the purchase
price of any Products, Accessories or Software that does not conform to this
warranty. We may use functionally equivalent reconditioned/refurbished/
pre-owned or new Products, Accessories or parts. No data, software or
applications added to your Product, Accessory or Software, including but not
limited to personal contacts, games and ringer tones, will be reinstalled. To avoid
losing such data, software and applications please create a back up prior to
requesting service.
How to Obtain Warranty Service or Other Information?
USAPhones 1-800-331-6456
Two-Way Radios 1-800-353-2729
Pagers 1-800-548-9954
CanadaAll Products 1-800-461-4575
TTYTTY 1-888-390-6456
For Accessories and Software, please call the telephone number
designated above for the product with which they are used.
You will receive instructions on how to ship the Products, Accessories or
Software, at your expense, to a Motorola Authorized Repair Center. To obtain
service, you must include: (a) a copy of your receipt, bill of sale or other
comparable proof of purchase; (b) a written description of the problem; (c) the
Motorola Limited Warranty
59
Page 62
name of your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your address and
telephone number.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR
REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS
THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF
THE PRODUCT, ACCESSORY OR SOFTWARE, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR
LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER
Motorola Limited Warranty
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY
OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO
THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length of an
implied warranty, so the above limitations or exclusions may not apply to
60
Page 63
you. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state or from one jurisdiction to another.
Laws in the United States and other countries preserve for Motorola certain
exclusive rights for copyrighted Motorola software such as the exclusive rights to
reproduce and distribute copies of the Motorola software. Motorola software may
only be copied into, used in, and redistributed with, the Products associated with
such Motorola software. No other use, including without limitation disassembly of
such Motorola software or exercise of the exclusive rights reserved for Motorola,
is permitted.
Motorola Limited Warranty
61
Page 64
Software Copyright Notice
The Motorola products described in this manual may include copyrighted
Motorola and third party software stored in semiconductor memories or other
media. Laws in the United States and other countries preserve for Motorola and
third party software providers certain exclusive rights for copyrighted software,
such as the exclusive rights to distribute or reproduce the copyrighted software.
Accordingly, any copyrighted software contained in the Motorola products may
not be modified, reverse-engineered, distributed, or reproduced in any manner to
the extent allowed by law. Furthermore, the purchase of the Motorola products
shall not be deemed to grant either directly or by implication, estoppel, or
otherwise, any license under the copyrights, patents, or patent applications of
Motorola or any third party software provider, except for the normal, nonexclusive, royalty-free license to use that arises by operation of law in the sale of
a product.
Patent Notice
This product is covered by one or more of the following United States patents.
This product is controlled under the export regulations of the United States of
America and Canada. The Governments of the United States of America and
Canada may restrict the exportation or re-exportation of this product to certain
destinations. For further information contact the U.S. Department of Commerce
or the Canadian Department of Foreign Affairs and International Trade.
Export Law Assurances
63
Page 66
64
Page 67
Page 68
•No license fee or airtime charges!•Weather-resistant•Quick release Swivel Belt Clip included
•Up to 5 mile range
*Depending on terrain and conditions
•22 channels, each with 38 interference
eliminator codes
Privacy feature that helps minimize
interference from other groups
•Multiple Audible Call Tones
Multiple distinct ringing options so your
group can identify who’s calling
•Scan
Easily finds your group’s channel and
code by searching all combinations
•Automatic Power Off
Saves battery life by shutting down after
user-defined period of inactivity
•Illuminated Display
Easy to read your settings in dark places
•Keypad Lock
Prevents your settings from being
accidentally changed
•Rechargeable Battery Kit
•Keep a spare battery charged and ready
to go with this optional accessory
•Vehicle Power Adapter
Recharge your radio on the go with this
optional accessory (works with NiMH
rechargeable battery, not included)
•QuieT6000™
Helps keep radios outside your group
from disturbing you with ring tones or
conversation
•User’s guide included
•Batteries (not included)
Requires 3 AA Alkaline batteries or one
NiMH rechargeable battery
•Low Battery Alert
Audible tone and visual display tell you
when battery is running down
•Talk Hands-Free (VOX / iVOX)
“Voice activation” (VOX / iVOX) lets you
talk hands-free with or without optional
accessories
•1 Year Limited Warranty
To obtain a copy of this warranty prior to
purchase, please ask retailer
FCC GMRS LICENSE
REQUIRED
•Accessories for T6200 series - Convenient headphones, some with hands-free talk capabilities, mesh and waterproof carry
cases, and rechargeable battery packs available from your retailer or www.motorola.com
Note: Weather radio service may not be available in all areas. Check with your local weather office for frequency and details or
visit www.nws.noaa.gov/nwr in the US or www.msc-smc.ec.gc.ca/cd/factsheets/wxradio in Canada. The use of the NOAA
logo does not provide an endorsement or implied endorsement by NOAA's National Weather Service nor does the use of the
Weatheradio logo provide an endorsement or implied endorsement by Environment Canada.