Hi, I’m QuickStart and I’m going to help you get started!
The Motorola
are durable two-way radios that operate on Family Radio
Service (FRS) frequencies, require no service fee or license,
and can be used anywhere in the United States and other
areas as listed by the FCC.
These radios offer more than just a way of keeping in touch.
The T6200 provides 14 channels and 38 interference eliminator
codes, five audible call tones, accessory connector, signal-
strength indicator, auto power off, and QuieT6000
The T6210 includes all the features found on the Motorola Talkabout T6200 plus
features such as Eavesdrop Reducer and VibraCall
The T6220 includes five additional call tones, eight NOAA weather channels, and
weather alert.
A detachable quick reference peel-off sticker that you can stick on the back of your
radio is included. This sticker will help you identify the settings and icons displayed
on your radio. This information is also included in the Getting Started section which
begins on page 14.
â
Talkabout® T6200, T6210, and T6220 radios
TM
.
®
alert.
Introduction
1
Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio
The information provided in this document supersedes the general safety
information contained in user guides published prior to July 2000. For information
regarding radio use in a hazardous atmosphere please refer to the Factory Mutual
(FM) Approval Manual Supplement or Instruction Card, which is included with radio
models that offer this capability.
RF Operational Characteristics
Your radio contains a transmitter and a receiver. When it is ON, it receives and
transmits radio frequency (RF) energy. The radio operates in the frequency range of
450 MHz to 470 MHz.
Exposure to Radio Frequency Energy
Your Motorola radio is designed to comply with the following national and
international standards and guidelines regarding exposure of human beings to radio
frequency electromagnetic energy:
•United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J
•American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992
•Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
Safety and General Information
5
•National Council on Radiation Protection and Measurements (NCRP) of the
United States, Report 86, 1986
•International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
•National Radiological Protection Board of the United Kingdom 1995
•Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio
Frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300
GHz, 1999
To assure optimal radio performance and make sure human exposure to radio
frequency electromagnetic energy is within the guidelines set forth in the above
standards, always adhere to the following procedures:
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the radio and may violate
FCC regulations.
DO NOT hold the antenna when the radio is “IN USE”. Holding the antenna
affects the effective range.
Safety and General Information
6
Two-Way Radio Operation
When using your radio as a traditional two-way radio, hold the radio in
a vertical position with the microphone two to three inches (5.0 to
7.5 cm) away from the lips.
Body-Worn Operation
To maintain compliance with FCC RF exposure guidelines, if you wear a radio on
your body when transmitting, always place the radio in a Motorola supplied or approved clip, holder, holster, case, or body harness. Use of non-Motorolaapproved accessories may exceed FCC RF exposure guidelines. If you do not use
a body-worn accessory, ensure the antenna is at least one inch (2.5 cm) from
your body when transmitting.
Approved Accessories
For a list of approved Motorola accessories refer to the Two-Way Radio section of
www.motorola.com/store.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed or otherwise configured for
electromagnetic compatibility.
Safety and General Information
7
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your
radio in any facility where posted notices instruct you to do so. Hospitals or health
care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of a
radio must be in accordance with applicable regulations per airline crew instructions.
Medical Devices
Pacemakers
The Health Industry Manufacturers Association recommends that a minimum
separation of 6 inches (15 centimeters) be maintained between a handheld wireless
radio and a pacemaker. These recommendations are consistent with the
independent research by, and recommendations of, Wireless Technology Research.
Persons with pacemakers should:
•ALWAYS keep the radio more than six inches (15 centimeters) from their pace-
Safety and General Information
maker when the radio is turned ON.
•not carry the radio in the breast pocket.
•use the ear opposite the pacemaker to minimize the potential for interference.
•turn the radio OFF immediately if you have any reason to suspect that interfer-
ence is taking place.
8
Hearing Aids
Some wireless radios may interfere with some hearing aids. In the event of such
interference, you may want to consult your hearing aid manufacturer to discuss
alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your
device to determine if it is adequately shielded from RF energy. Your physician may
be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations on the use of radios in the area where you drive.
Always obey them.
When using your radio while driving, please:
•Give full attention to driving and to the road.
•Use hands-free operation, if available.
•Pull off the road and park before making or answering a call if driving conditions
so require.
Safety and General Information
9
Operational Warnings
For Vehicles with an Air Bag
Do not place a portable radio in the area over an air bag or in the air bag deployment
area. Air bags inflate with great force. If a portable radio is placed in the air bag
deployment area and the air bag inflates, the radio may be propelled with great force
and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
atmosphere, unless it is a radio type especially qualified for use in such areas as
“Intrinsically Safe” (for example, Factory Mutual, CSA, or UL Approved). Do not
remove, install, or charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to above include
fueling areas such as below decks on boats, fuel or chemical transfer or
storage facilities, areas where the air contains chemicals or particles, such
as grain, dust or metal powders, and any other area where you would
normally be advised to turn off your vehicle engine. Areas with potentially
Safety and General Information
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you
are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off twoway radio”. Obey all signs and instructions.
explosive atmospheres are often but not always posted.
10
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna
comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a
conductive material such as jewelry, keys, or beaded chains touch exposed
terminals. The conductive material may complete an electrical circuit (short circuit)
and become quite hot. Exercise care in handling any charged battery, particularly
when placing it inside a pocket, purse, or other container with metal objects.
Charging Safety Instructions
Before using the battery charger, read all instructions and cautionary markings on
the:
1. battery
2. battery charger, and
3. radio using the battery.
Caution: To reduce the risk of injury, charge only the rechargeable batteries listed.
Other types of batteries may burst, causing personal injury and damage.
Safety and General Information
11
Single-Unit Charger
Kit NumberDescription
NTN9393110V - NiMH Charging Adapter
Batteries
Capacity in milliampere-
Kit Number
NTN9395550 mAHT6000-SeriesNiMH
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate the charger if it has received a sharp blow, or has been dropped
or damaged in any way.
3. Do not disassemble the charger if it has received a sharp blow, or has been
dropped or damaged in any way.
4. Never alter the AC cord or plug provided with the unit. If plug will not fit the
outlet, have proper outlet installed by a qualified electrician. An improper
Safety and General Information
condition can result in a risk of electric shock.
5. To reduce risk of damage to cord or plug, pull the plug rather than the cord when
disconnecting charger from AC receptacle.
6. To reduce the risk of electric shock, unplug the charger from the outlet before
attempting any maintenance or cleaning.
hour mAH
DescriptionComposition
12
7. Use of an attachment not recommended or sold by Motorola may result in a risk
of fire, electric shock, or personal injury.
8. Make sure that the cord is located so that it will not be stepped on, tripped over,
or subjected to damage or stress.
9. An extension cord should not be used unless absolutely necessary. Use of an
improper extension cord could result in a risk of fire and/or electric shock. If an
extension cord must be used, make sure:
- That the pins on the plug of the extension cord are the same number, size and
shape as those on the plug of the charger.
- That the extension cord is properly wired and in good electrical condition, and
- That the cord size is18 AWG for lengths up to 100 feet, and 16 AWG for lengths
up to 150 feet.
10. The supply cord of this charger cannot be replaced. If the cord is damaged, call
Motorola Product Services at:
- Lock the keypad (when
held down and not in a
menu)
- Exit the menu (when held
down while in a menu)
UseQto:
- Turn on backlight
(short press).
- Press and hold to
switch between
Weather Mode and
Two-Way Mode
(T6220 Only).
Use
[ and ] to:
- Adjust volume
- Scroll through menu
settings
14
Getting Started
Use
(
(Call)
to:
- Transmit call tone
M to:
Use
- Talk on the radio
- Exit the menu (when briefly
pressed while in a menu)
Use
(short press)
(long press)
(Scan/Monitor) to
)
- Turn Scan on/off
- Monitor the channel &
check signal strength
Microphone
Belt Clip
- Squeeze the top and
bottom of the clip to attach
or detach the clip from the radio.
Note: The belt clip holds the
radio while being worn
on your belt. It was designed
for your convenience and is
not meant to secure your radio
under all circumstances. For
high activity environments, an
accessory carry case is more
appropriate to secure the radio.
When using audio
accessories, ensure that
they are plugged in before
you turn on the radio.
* Motorola recommends
that the volume level be
kept at a comfortable
listening level when using
audio accessories.
*
Getting Started
NiMH Battery Charging Contacts
Check out the accessory brochure for other cool stuff
available from Motorola.
000884-O
15
Installing Batteries
Your radio uses three AA batteries or a rechargeable Nickel-Metal Hydride
(NiMH) battery.
Some radio packages include a NiMH battery with charger adapter cover, charging
dock, and charger. If you don’t have these items, they’re also available in the NiMH
battery upgrade kit (56319). Call 1-800-353-2729 (U.S.A.) or 1-800-461-4575
(Canada) for the dealer nearest you.
• Turn off the radio by pressing and holding
• Push latch up until it clicks.
• Lift back cover off.
Getting Started
16
P
.
Latch
• Remove and replace batteries so the
+ marking matches the one in the
compartment or the NiMH charge
contacts are facing out toward the
battery door.
Getting Started
• Hook back cover on the hinges.
• Close the battery door, pressing
lightly until the latch clicks and returns
to its original position.
17
Battery Meter
The battery meter on the top-left corner of the display shows how much
battery power you have. It shows d (full), b (two-thirds full), c
(one-third full), and a (empty). When it’s c, the radio beeps every
10 minutes. So, change or charge those batteries!
Battery Life
The following chart lists the approximate battery life during two-way use for alkaline
and NiMH batteries. See page 26.
Battery TypeTwo-Way Use *
AA alkaline35 hours
NiMH12 hours
Getting Started
*Two-way use is defined as 90% standby time, 5% talk time, and 5% receive time.
Note:
Battery life will be reduced if you regularly use Hands-Free (VOX) accessories,
Weather, or Scan.
18
Charging the NiMH Battery
Charge the NiMH battery overnight (16 hours) before using it for the first time, it
will only need up to four hours of charging thereafter.
Charger
Battery
Adapter
Cover
Charger
Or
Light Indicator
• Turn off the radio by pressing and holding P, or place the NiMH battery in the
charger adapter cover.
At the contacts on the back of the radio (or if you are charging just the battery, at the
battery contacts):
• Position the charger so that the large hook on the end of the charger is over the
large slot on the battery door or if you are charging the battery by itself, on the
large slot on the charger adapter cover.
• Place the small hook on the other end of the charger over the small slot and snap
it into place.
• Plug in the charger.
Getting Started
19
Charging Status
The Light Indicator shows the charging status when the charger is connected to
the radio, the NiMH battery, or the charging dock.
Charging
Light Indicator
Color
Solid RedRapid charging
Flashing GreenTop-off charging90% to 100%
Green
Solid
Flashing
Flashing Ye l l o w
Getting Started
Note: When moving between hot and cold environments, do not charge the battery
Note:
20
Red
until the battery temperature acclimates (usually about 20 minutes).
When charging the battery by itself, remove the charger from the charger adapter
cover before inserting and/or removing the battery from the charger adapter cover.
Charging Status and Description
Charging complete100%
Battery faulty
If flashing red persists for more than one minute, the
battery is faulty and should be replaced.
Standby
Battery waiting to charge.
Temperature out of range for charging; must be
between 5
o
to 40o C or 41o to 104o F
Level
Complete
Up to 90%
-
-
Charging Dock
The charging dock provides drop-in charging convenience. The charging dock can
be mounted or placed on any flat surface (such as a wall or workbench) and turns
your radio into a stationary intercom while keeping it charged and ready for any
adventure.
To mount the charging dock:
• Wrap the power cord under the charging dock.
Use the cutouts to hold the cord in place.
• Attach using two #6 x ¾” screws appropriate
for the mounting surface.
Cutouts
Getting Started
21
22
• Position the charger with the hook on the light
indicator end over the left slot.
Charging Dock
• Snap the hook on the cord end into the right
slot, clamping the charger onto the charging
dock contacts.
• Plug in the charger.
Light Indicator
Charger
• Place the radio, or the NiMH battery in the
Getting Started
charger adapter cover, into the charging dock
until you hear a click.
• When the light indicator turns solid green, the
battery is fully charged.
Turning On Your Radio
Press and HoldNormal Menu Mode
P
The radio beeps and the screen
temporarily displays every
image.
The red light above the
button flashes every three
seconds.
Press and HoldSimple Menu Mode (see page 46)
The radio beeps and the screen
P and \
temporarily displays only six
images.
The red light above the
button flashes every three
seconds. You have access to
only the Channel, Code, and
Call Tone menus.
P
P
Getting Started
23
Your Radio’s Display
Lock Set
Battery Meter
Channel Scan On
QuieT6000™
Eavesdrop Reducer
Volume Control
Signal Strength
I
Getting Started
ndicator
VibraCall® Alert On
Interference Eliminator
Code
Automatic Power Off
Hands-free Use with
Accessories (VOX)
Transmit Call Tone\
Call Tone Received
Channel Indicator
Ring Alert On
Weather On
Turning Off Your Radio
To turn off your radio press and hold P for one second. The radio beeps and the
display goes blank.
24
Changing Settings While Turning On Your Radio
The following table lists additional functions you can set by pressing and holding
specific key combinations while turning on your radio.
Key(s) Pressed and Held
While Turning On Your Radio
Function
\
+
)
[
]
M
+
M
+
P
or
+
P
+
P
P +
P + \
P +
P
(Call)
(
+ VOX accessory attached
Reset factory settings.
Turns audible button beeps and local audible call
tones on or off.
Turns Talk Confirmation Tone on or off.
Turns on Simple Menu mode. See page 46.
Enable/disable QuieT6000
page 39.
Enable External VOX (with accessory).
(Setting 1) See
Getting Started
25
Accessing and Setting Features
Almost everything you can do with your radio is done using the same basic key
sequence! Use your radio’s
way you want them. All the features that work using this key sequence are described
on the following pages.
PressDisplayThen Press
and[ or] to select options and set features the
\
\
the icon representing the
feature you want
[
or ] to select the option, then press
M
or wait ten seconds (60 seconds for Simple
Menu mode) to save the setting or press and
\
.
hold
Setting the Battery Type
This feature allows the battery meter to recognize and properly display the power
Getting Started
usage for either alkaline or rechargeable batteries.
To set the battery type, press \ until d displays. Either A
(Alkaline) or n (NiMH or NiCad rechargeable) is blinking. Press [
or ] until your choice of A or n displays, then press M to set.
26
Backlight
Being in the dark is never a problem. Your radio has a backlight
that turns on automatically any time you press a button. The
backlight turns off automatically four seconds after you last pressed
a button.
You can also illuminate your display by pressing the
or
button (T6220).
Ro
R button (T6200 and T6210)
Getting Started
27
Talking and Listening
Before You Can Talk
To talk with someone on your two-way radio, both of you must be on the same
channel, interference eliminator code, and Eavesdrop Reducer code (T6210 and
T6220 only).
The channel is the radio frequency wave your radio uses to transmit. The
interference eliminator code filters out static, noise, and unwanted messages. Refer
to the Frequency and Code Charts beginning on page 48 for channel and code
choices. The Eavesdrop Reducer code makes your transmissions sound garbled to
anyone listening who is not set to that code. See page 38.
Setting the Channel
To set the channel, press \ once. The channel number begins to
blink. Then press [ or ] to set the channel. Then proceed to the
next menu or wait 10 seconds to save the channel setting. To
Talking and Listening
quickly exit the menu and go back to the first display screen, press
.
M
The red indicator light above the P button flashes quickly whenever the channel is
in use. Keep scrolling until you find a clear channel.
28
Setting the Interference Eliminator Code
To set the code, press \ twice until the code number display
begins to blink. Then press [ or ] to set the code. Press M to
save the code setting. To hear everyone on your channel, select
code
0.
You can specify a different code for each channel. To set a channel and code
combination, press \ and then press [ or ] to select the channel. Press \
again and then press [ or ] to select a code. Press M to exit the menu and to
save the channel and code combination. To set another channel and code
combination, repeat these steps.
Volu me
You can set the volume whenever you are not using a menu. Press
or ] until it’s just right. The display will show
[
)
1
with
setting (
to
20
1
being
the lowest volume and
V and the volume
20 being the
5
highest volume.
Talking and Listening
Caution:
Do not hold the radio too close to your ear when the volume is at a high
setting. This could cause hearing damage.
29
To Talk
Note:
Talking Range
Talking and Listening
Optimal Range
• Flat, open areas from five
The microphone is located under the ) button. So don’t cover it when you press
M
.
Press and hold M and talk two-to-three inches away from the
microphone. When you’re finished, just release M (Press and hold to talk,
release to listen). While transmitting, the red indicator light above the P
button glows.
feet up to two miles (lineof-sight)
30
Medium Range
• Buildings or trees
Minimal Range
• Dense foliage or
mountains
• Buildings or vehicles
Using Accessories
Make sure the radio is turned off before plugging audio accessories into the
accessory port. Before you place an accessory on your head or in your ear, turn
the volume down. After placing the accessory on your head or in your ear, adjust the
volume by pressing [ or
.
]
Monitor/Signal Strength Indicator
The ) button allows you to listen to all activity on a channel (open squelch) to tell
whether the channel is currently in use.
when a radio is moving out of range.
To check for channel activity, press and hold the ) button. You’ll hear static if the
channel is clear and w will display. Don’t transmit if you hear conversation. To
avoid interrupted conversation, wait until the channel is clear or switch to another
channel.
he w helps you determine when a radio is moving out of range by
T
displaying a receive signal-strength value next to the
press and hold
indicates the relative strength of the incoming signal.
. This value from
)
This
button
1
(weakest) through 6 (strongest)
can also help you determine
w while you
6
Signal Strength
Indicator
Talking and Listening
Note:
Obstacles that block the signal path may affect the strength of the incoming signal.
31
Alerts
Alerts allow members of your group to notify each other that they want to talk.
Alerts can be audible, visual, or vibrating.
You can also determine how your radio will alert you when you’re receiving: vibrate,
ring, both, or none. Your radio will vibrate and/or ring only the first time you receive a
transmission or call. It will not ring or vibrate again until 30 seconds of inactivity have
elapsed.
Call Tone and Call Display
Your radio can transmit different call tones to other radios in your group so you can
alert them that you want to talk to them. Each person in the group can have an
individual call tone.
Alerts
To set your call tone, press \ as needed to display ^. You can
press [ or ] to scroll through the available call tones. The radio
plays a sample of each tone as you scroll through them. To use your
call tone, just press
the channel number.
to transmit it to others. The ^displays next to
(
32
Ring Only (T6200 Only)
The ring feature rings the call tone you’ve selected to notify you of two-way radio
reception. When you set this feature, the radio produces the call tone you’ve
selected each time you receive a two-way radio transmission.
To set the Ring feature, press \ until B is displayed and then
press [ or ] to select n or Y.
If you select Y, the B will remain on the display after you exit the menu.
Alerts
33
Ring and/or VibraCall® (T6210 and T6220 Only)
Your radio features Ring and/or VibraCall®, a vibrating alert to notify you of
two-way radio reception in noisy environments.
To set Ring and/or VibraCall
press [ or ] to select the desired setting.
Display
Within
Setting
Menu
®
, press \ until B and/or i is displayed and then
Function
34
-
Alerts
1i
2
3
B
Bi
Your radio doesn’t sound an alert, just the actual
transmission. You will still hear the talk confirmation tone (if
activated).
Your radio vibrates to alert you.
Your radio rings your call tone when you receive a call.
Your radio vibrates and rings your call tone when receiving.
Talk Confirmation Tone
Whenever you turn on the talk confirmation tone feature, your two-way radio
transmits a unique tone when you finish transmitting. It’s like saying “Roger” or
“Over” and lets others know you’re finished talking. If you don’t hear the talk
confirmation tone, you can enable it by pressing and holding ] as you turn on
your radio. Now, whenever you release the M button, you let your friends know
you’re finished talking by transmitting a tone. To disable the talk confirmation
tone feature, turn your radio off and then back on while pressing and holding ].
Button Beeps
Every time you press a button on your radio, it beeps unless you turn Button Beeps
off. To turn button beeps off, turn your radio on while you press and hold [. To turn
button beeps back on, turn the radio off and then back on again while you press and
hold [.
When Button Beeps are turned off, you won’t hear call tones that you send.
Alerts
35
Hands-Free Use (VOX)
Hands-Free Use With Accessories
VOX allows you to transmit “hands-free” by talking while using VOX accessories
connected to the radio.
To set VOX, plug in your accessory before you turn on your radio. When you turn on
your radio, flashing g displays. Your radio will now detect your voice and transmit
every time you talk. When you transmit using a VOX headset, you will hear yourself
talking through the accessory speaker. This lets you know VOX is working.
Press M to turn off VOX and return to the regular way of transmitting. The g will
disappear. To reset VOX use, turn your radio off and then back on with your
accessory plugged in.
Note: When using accessories, ensure that they are plugged in before you turn on
Hands-Free Use (VOX)
Note: There is a short delay when you start talking before the transmitter turns on.
the radio.
36
Setting Sensitivity Level
The sensitivity level allows you to compensate for background noise when using
an accessory. If you are not using an accessory, the sensitivity level will adjust your
microphone’s sensitivity. By adjusting the sensitivity level up or down, you can
minimize the chance of unintended noises triggering a transmission, or increase the
microphone’s ability to pick up quiet voices.
To set sensitivity level, press \ as needed, until g and a value
through
High (
Medium (
Low (
When you connect a VOX accessory, the radio will automatically be set to your last
sensitivity level.
3 are displayed. Then select:
3) for quiet environments
2) for most environments
1) for noisy environments
1
1
g
Hands-Free Use (VOX)
37
Privacy
Eavesdrop Reducer (T6210 and T6220 Only)
Your radio has the Eavesdrop Reducer feature, a scramble code that makes
your transmissions sound garbled to anyone listening without the same
code. It doesn’t guarantee secrecy, but it adds an extra layer of privacy.
Don’t forget -- all the radios have to be set to the same Eavesdrop Reducer
code for the transmissions to be clear.
To turn the Eavesdrop Reducer feature on, press \ as needed until e is
displayed, then
After you exit the menu, the display will show e.
Privacy
To turn the Eavesdrop Reducer feature off, press \ as needed until e is
displayed, then
select code 1, 2, or
select
-. After you exit the menu, the e icon will disappear from
3.
the display.
38
QuieT6000™
The QuieT6000TM function helps ensure uninterrupted communication among
Motorola Talkabout T6200 and T6300 series radios - it helps prevent you from
hearing transmissions from other radios. However, other radios can hear you.
To turn the QuieT6000 function on or off, press \ as needed until F is displayed.
Then select one of the following settings:
SettingDisplayFunction
-
38
QuieT6000
is turned off.
14
1
14
QuieT6000
scanning.
is turned on, but is suspended while
Privacy
2
QuieT6000 is turned on, including while scanning.
14
You can also turn the QuieT6000
pressing and holding
while you turn on your radio.
(
function on (Setting 1) or off (Setting -) by
39
QuieT6000™ (Continued)
If you have a T6200 radio with QuieT6000 on and want to talk to others in your
group who also have QuieT6000 on, you must first transmit a call tone before talking
to them. When the call tone is transmitted, ^ will display on the other T6200 or
T6300 series radios with the same channel, interference eliminator code, and
QuieT6000 on, letting them know that you want to talk to them. Those radios can
then receive and transmit until 30 seconds of inactivity occurs, which resets the
QuieT6000 function. While QuieT6000 is on, F is displayed to indicate that the
function is on. However, during the 30 seconds of inactivity, F will flash.
Unique Situations
QuieT6000 can also keep your radio quiet when you are in a situation where noise
can be disruptive, such as when you are in a movie theater or out hunting. Set
QuieT6000 to either 1 or 2 and set your radio’s alert to 1 (VibraCall only). Now
Privacy
when you receive a call from another T6200 or T6300 series radio, your radio will
vibrate while the ^ displays on the screen. The ^ will remain on the screen until you
press any button. Only then can you receive and transmit to those radios until 30
seconds of inactivity occurs and the QuieT6000 function resets.
40
Weather (T6220 Only)
You can’t change the weather, but you can be prepared for it
whenever you take your Motorola Talkabout T6220 radio with
you. That’s because it tunes into National Oceanic and
Atmospheric Administration (NOAA) Weather Radio broadcasts.
You can listen to a weather channel or you can even set your
radio to alert you to emergency weather broadcasts.
And because NOAA Weather Radio now broadcasts warning
information for all types of hazards, routine broadcasts are
interrupted during emergencies for natural and technological warnings, watches,
and other critical information.
NOAA has transmitters located throughout the United States and Canada that
broadcast National Weather Service warnings, watches, forecasts, and other hazard
information 24 hours a day.
Whenever you listen to a weather channel, you cannot use your radio for two-way
communications. However, a weather alert will notify you while the radio is in twoway mode (if you have enabled weather alert) and the radio is on but not
transmitting or receiving.
Turning On Weather Channel Reception
To turn on weather channel reception, press and hold the Ro button. To turn off
weather channel reception and return to two-way mode, press and hold the
button again.
Ro
Weather (T6220 Only)
41
Setting the Weather Channel
Your radio receives eight NOAA frequencies. See the Frequency and Code
Charts beginning on page 48 for a complete list.
After turning on the weather broadcast, press
channel display blinking.
Press [ or ] to select the strongest channel.
As with two-way radio reception, weather channel reception depends on how close
you are to a transmitter and whether you are indoors or outdoors. Also, because
weather channels are transmitted without codes, they may contain static or noise.
Note: In some isolated areas, it may not be possible to receive weather channel
transmissions.
Weather (T6220 Only)
\ to start the
42
Setting the Weather Alert
If you set the weather alert and switch back to two-way mode, o
Whenever NOAA transmits an emergency weather broadcast on the selected
channel, your radio alerts you using the selected alert mode, ring B or vibrate i,
and switches to the selected weather channel. If your radio is in weather mode, you
will receive a weather alert only on the selected channel.
To set weather alerts, switch to weather mode, press \ twice,
and press [ or ] to select
Note: The TalkAbout T6200-series two-way radios are designed to be two-way
radios primarily, with the added utility of features such as Weather Alert. The
radio uses the same circuitry for both two-way radio and weather alert
receptions. Therefore, you can miss a weather alert while you are engaged
in two-way communication (either transmitting or receiving). To ensure that
you do not miss a weather alert, leave the radio in the Weather Mode.
Y (on).
is displayed.
Weather (T6220 Only)
43
Other Important Features
Lock
To avoid accidentally changing radio operation, the Lock feature locks the Menu,
Volume Control, Weather (T6220 only), and Scan functions. Meaning that you can
only turn the two-way radio on and off, transmit, and monitor
You can make sure your menu settings won’t be changed
accidentally.Just turn on lock by pressing
Now you’ll see the f icon.
To turn Lock off, press \ again for three seconds.
Note: If your radio is in two-way mode and Weather Alert is enabled, an
emergency broadcast on the selected channel will still switch the radio to
that weather channel.
Scanning
Other Important Features
By using Scanning h, you can monitor channels and codes for transmissions
and lock in on the one that interests you. More importantly, you can find someone
in your group who has accidentally changed channels and is talking during your
scan. You don’t have to set a new channel or code, the radio just resets itself
temporarily to that channel and code and you can start talking.
for three seconds.
\
44
Lock On
Scanning (Continued)
To start scanning, briefly press ) (Scan/Monitor).
h
and begins to scroll through channels. When the radio detects channel activity, it stops
on that channel and displays its channel and code. You can talk to the person(s)
transmitting without having to switch channels by pressing
press
channel you selected before you activated Scan. If no
seconds, scanning will resume.
If you want to scan channels without interference eliminator codes, change the code
for your set channel to
. If you press
)
while the radio is scanning, the radio will transmit on the
M
0 before you briefly press
Your channel/code screen displays
.
To stop scanning, briefly
M
transmission occurs within five
.
)
Auto Power Off
You can program your radio to turn itself off after a certain period of inactivity. This
helps save battery life.
To set the automatic power off feature, press \ as needed to
display O. Press [ or ] to set the number of hours
which power shuts off.
After you exit the menu, O displays on the screen when the automatic power off
feature has been activated. Five minutes before the radio shuts off, an alert beep
sounds. Another alert beep will sound once per minute and O will flash
continuously during those five minutes.
Select - to turn off the automatic power off feature.
1 - 8, after
O
8
Other Important Features
45
Reset
You can reset your radio’s menu settings to the factory settings by turning it on while
pressing and holding M and \ or
M
and
.
)
Simple Menu
Simple Menu allows you to limit the number of menus displayed (Channel, Code,
and Call Tones) to allow for simpler radio operation. The Scan and Weather
features, along with most of the radio turn-on sequences (See page 25), are also
disabled to prevent accidentally changing the radio’s mode of operation.
If you want the radios in your group to keep the same settings that you have on your
radio, press \ as you turn each radio on. Simple Menu increases the menu time-
out to 60 seconds. To turn off Simple Menu, press \ as you turn on the radio.
If you want to set up Simple Menu for inexperienced users, without advanced
features activated such as Eavesdrop Reducer and QuieT6000, reset their radios to
the original factory settings by either pressing
Other Important Features
\ while turning on their radios. Then activate Simple Menu by turning their radios
off and then back on while pressing
\
.
)
and
or by pressing
M
46
M
and
Use and Care
glub
Use a soft damp cloth to
clean the exterior.
If the radio gets wet...
Turn it off and remove
batteries.
Do not immerse in water.Do not use alcohol or
cleaning solutions.
Use and Care
Dry with soft cloth.Do not use until completely
dry.
47
Frequency and Code Charts
The charts on these pages provide frequency and code compatibility information.
These charts are useful when using Motorola Talkabout two-way radios with other
FRS radios.
Note: Motorola 7/7x is an older Motorola radio that has seven codes common
with newer FRS radios.
Frequency and Code Charts
49
50
Troubleshooting
SymptomTry This:
No Power
Message not
transmitted
Hearing other
noises or
conversation on
a channel
Message
scrambled
Troubleshooting
Limited talk
range
Reposition or replace alkaline batteries.
Recharge or replace NiMH battery.
Make sure M is completely pressed as you transmit.
Reposition, replace, or recharge batteries.
Confirm interference eliminator code is set.
Shared channel or interference eliminator code may be in use, try
another.
Eavesdrop
radios’ settings; all radios must use the same Eavesdrop
code.
Steel and/or concrete structures, heavy foliage, use in buildings or
vehicles decrease range. Check for clear line of sight to improve
transmission.
Wearing radio close to body such as in a pocket or on a belt
decreases range. Change location of radio.
Reducer
code is on, or setting does not match other
Reducer
SymptomTry Th is :
Message not
received
Heavy static or
interference
Channel and/or
code locked
Confirm radios have the same channel and interference eliminator
code settings.
Make sure
Reposition, replace, or recharge batteries.
If QuieT6000
If QuieT6000
received call must be acknowleged by pressing any button (or a
VOX activation) before the radio can receive any incoming
transmissions.
Obstructions and operating indoors, or in vehicles, may interfere -change location.
Verify that the radio is not in Scan mode.
Eavesdrop
radios; all radios must use the same Eavesdrop
Radios are too close, they must be at least five feet apart.
Radios are too far apart or obstacles interfering with transmission.
Talk range is up to two miles in clear, unobstructed conditions.
Make sure menu is unlocked. Unlock by pressing \ for three
seconds.
M
is
NOT
being pressed while trying to listen.
feature is on, transmit call tone before talking.
feature is on, with only VibraCall selected, a
Reducer
code is on, or setting does not match other
Reducer
Troubleshooting
code.
51
52
Troubleshooting
SymptomTry This:
Cannot access
all menus
or
Cannot display
desired icon
Other radios not
receiving your
transmissions
Low batteries
Low battery
meter reading
although new
batteries are
installed
Charger LED
double flashing
Cannot activate
VOX
Verify whether Simple Menu is activated. Disable Simple Menu by
pressing
QuieT6000
QuieT6000
or turn
Replace alkaline batteries. Recharge or replace NiMH battery.
Extreme operating temperatures affect battery life.
Verify that the radio is set to the correct battery type. See page 26.
Charger not properly positioned. Reposition charger and ensure it
is firmly clamped to the radio, battery, or charging dock.
Battery power is very low; battery is charging up slowly before it
starts to quick charge.
Feature not set and on. See page 36.
while turning on the radio.
\
mode is set. Press ( to talk to members of your party
off.
Motorola Limited Warranty
Motorola Personal Communications Products Purchased in the United States and
Canada
I.What This Warranty Covers
•Products. Defects in materials and workmanship in wireless cellular telephones,
pagers, and/or two-way radios, and certain accessories that are sold with them,
such as the battery, battery charger and holster manufactured and/or sold by
Motorola (Products).
•Batteries
manufactured by Motorola and/or sold with Products are covered by this
warranty only if the fully-charged capacity falls below 80% of rated capacity or
they leak.
•Software
any software supplied with the Products.
II. What the Period of Coverage Is
From the date the Products are purchased by the first end-user:
•Products.
series and Talkabout series two-way radio accessories is for 90 days.
•Software.
•Repairs / Replacements.
or for 90 days from the date you receive it, whichever is longer.
. Defects in materials and workmanship in batteries that are
. Physical defects in the media that tangibly embodies each copy of
The warranty is for one year. Exception: The warranty for Spirit GT
The warranty is for 90 days.
The warranty is for the balance of the original warranty
Motorola Limited Warranty
53
Motorola Limited Warranty
54
III. Who is Covered
This warranty extends to the first end-user purchaser, only.
IV. What We Will Do to Correct Warranty Problems
At no charge to you, we have the option to repair or replace the Products or
software that do not conform to the warranty, or to refund the Products’ purchase
price. We may use functionally equivalent reconditioned/refurbished/pre-owned
or new Products or parts. No software updates are provided.
You will receive instructions on how to ship the Products to Motorola. You must
ship the Products to us with freight, duties and insurance prepaid. Along with the
Products you must include: (a) a copy of your receipt, bill of sale or other
comparable proof of purchase; (b) a written description of the problem; (c) the
name of your service provider (if this Product requires subscription service); (d)
the name and location of the installation facility (if applicable) and, most
importantly; (e) your address and telephone number. If requested, you must also
return all detachable parts such as antennas, batteries and chargers. RETAIN
YOUR ORIGINAL PROOF OF PURCHASE.
We will ship repaired or replacement Products at our expense for the freight and
insurance, but at your expense for any duties. If additional information is needed,
please contact us at the telephone number listed above.
VI. What This Warranty Does Not Cover
•Products that are operated in combination with ancillary or peripheral
equipment or software not furnished by Motorola for use with the Products
(“ancillary equipment”), or any damage to the Products or ancillary equipment
as a result of such use. Among other things, “ancillary equipment” includes
batteries, chargers, adaptors, and power supplies not manufactured or supplied
by Motorola. Any of these voids the warranty.
•Someone other than Motorola (or its authorized service centers) tests, adjusts,
installs, maintains, alters, modifies or services the Products in any way. Any of
these voids the warranty.
•Rechargeable batteries that: (a) are charged by other than the Motorolaapproved battery charger specified for charging such batteries; (b) have any
broken seals or show evidence of tampering; (c) are used in equipment other
than the Product for which they are specified; or (d) are charged and stored at
temperatures greater than 60 degrees centigrade. Any of these voids the
warranty.
•Products that have: (a) serial numbers or date tags that have been removed,
altered or obliterated; (b) board serial numbers that do not match each other, or
board serial numbers that do not match the housing; or (c) nonconforming or
non-Motorola housings or parts. Any of these voids the warranty.
•Defects or damage that result from: (a) use of the Products in a manner that is
not normal or customary; (b) improper operation or misuse; (c) accident or
Motorola Limited Warranty
55
Motorola Limited Warranty
56
neglect such as dropping the Products onto hard surfaces; (d) contact
with water, rain, extreme humidity or heavy perspiration; (e) contact with
sand, dirt or the like; or (f) contact with extreme heat, or spills of food or
liquid.
•Physical damage to the surface of the Products, including scratches,
cracks or other damage to a display screen, lens or other externally
exposed parts.
•Failure of Products that is due primarily to any communication service or
signal you may subscribe to or use with the Products.
•Coil cords that are stretched or that have any broken modular tabs.
•Products that are leased.
Flat-rate repair rates may apply to Products not covered by this warranty. To
obtain information about Products needing repairs that are not covered by this
warranty, please call the telephone number previously listed. We will provide
information on repair availability, rates, methods of payment, where to send
the Products, etc.
VII. Some Other Limitations
This is Motorola’s complete warranty for the Products, and states your
exclusive remedies. This warranty is given in lieu of all other express
warranties. Implied warranties, including without limitation, the implied
warranties of merchantability and fitness for a particular purpose, are given
only if specifically required by applicable law. Otherwise, they are specifically
excluded.
No warranty is made as to coverage, availability, or grade of service provided
by the Products, whether through a service provider or otherwise.
No warranty is made that the software will meet your requirements or will work
in combination with any hardware or applications software products provided
by third parties, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software products will be
corrected.
In no event shall Motorola be liable, whether in contract or tort (including
negligence) for damages in excess of the purchase price of the Product, or for
any indirect, incidental, special or consequential damages of any kind, or loss
of revenue or profits, loss of business, loss of information or data, or other
financial loss arising out of or in connection with the ability or inability to use
the Products, to the full extent these damages may be disclaimed by law.
Motorola Limited Warranty
57
Motorola Limited Warranty
58
VIII.Patent and Software Provisions
At Motorola’s expense, we will defend you, and pay costs and damages that
may be finally awarded against you, to the extent that a lawsuit is based on a
claim that the Products directly infringe a United States patent. Our obligation
is conditioned on: (a) you notifying us promptly in writing when you receive
notice of the claim; (b) you giving us sole control of the defense of the suit and
all negotiations for its settlement or compromise; and (c) should the Products
become, or in Motorola's opinion be likely to become, the subject of a claim of
infringement of a United States patent, you permit us, at our option and
expense, either to: procure for you the right to continue using the Products;
replace or modify them so that they become non-infringing; or grant you a
credit for such Products, as depreciated, and accept their return. The
depreciation will be an equal amount per year over the lifetime of the Products,
as established by Motorola.
Motorola will have no liability to you with respect to any claim of patent
infringement that is based upon the combination of the Products or parts
furnished under this limited warranty with ancillary equipment, as defined in
VI., above.
This is Motorola’s entire liability with respect to infringement of patents by the
Products.
Laws in the United States and other countries preserve for Motorola and other
third party software providers certain exclusive rights for copyrighted software,
such as the exclusive rights to reproduce in copies and distribute copies of
such software. The software may be copied into, used in and redistributed with only
those Products that are associated with such software. No other use, including
without limitation, disassembly or reverse engineering of such software or exercise
of exclusive rights in such software is permitted.
IX. State Law and Other Jurisdiction Rights
Some states and other jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights,
which vary from jurisdiction to jurisdiction.
To obtain information on Motorola Personal Communications Products, including
warranty service, accessories and optional Extended Warranties on selected
Products, please call:
To correspond with Motorola about the Products, please write us at
http://www.motorola.com or at:
USACanada
Motorola, Inc.Motorola Canada Limited
600 North U.S. Highway 455875 Whittle Road
Libertyville, IL 60048Mississauga, ON L4Z 2H4
Motorola Limited Warranty
59
Computer Software Copyrights
The Motorola equipment described in this manual may include copyrighted Motorola
computer programs stored in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola certain exclusive rights for
copyrighted computer programs, including the exclusive right to copy or reproduce in
any form the copyrighted computer program. Accordingly, any copyrighted Motorola
computer programs contained in the Motorola equipment described in this manual may
not be copied or reproduced in any manner without the express permission of Motorola,
Inc. Furthermore, the purchase of Motorola equipment shall not be deemed to grant
either directly or by implication, estoppel, or otherwise any license under the copyrights,
patents or patent applications of Motorola, except for the normal nonexclusive, royalty
free license to use arising by operation of law in the sale of this product.
Patent Notice
This product is covered by one or more of the following United States patents.
Changes or modifications not expressly approved by Motorola may void the user’s
authority granted by the FCC to operate this radio and should not be made. To comply
with FCC requirements, transmitter adjustments should be made only by or under the
supervision of a person certified as technically qualified to perform transmitter
maintenance and repairs in the private land mobile and fixed services as certified by an
organization representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized by the FCC
equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be
distributed is subject to government regulations and may be prohibited.
Export Law Assurances
This product is controlled under the export regulations of the United States of America
and Canada. The governments of the United States and Canada may restrict
exportation and re-exportation of this product to certain destinations. For further
information, contact the U.S. Department of Commerce or the Canadian Department of
Foreign Affairs and International Trade.
•No license fee or airtime charges!•Weather-resistant•Quick release Swivel Belt Clip included
•Up to 2 mile range
*Depending on terrain and conditions
•QuieT6000™
Helps keep radios outside your group
from disturbing you with ring tones or
conversation
•Automatic Power Off
Saves battery life by shutting down after
user-defined period of inactivity
•Keypad Lock
Prevents your settings from being
accidentally changed
•Low Battery Alert
Audible tone and visual display tell you
your battery is running down
•14 channels, each with 38 interference
eliminator codes
Privacy feature that helps minimize
interference from other groups
•“Roger” Beep
Signals others you’re done talking
•Call Button
Get others’ attention before you start
talking
•Scan
Easily finds your group’s channel and
code by searching all combinations
•Durable, fixed antenna
Maximizes talk range
•1 Year Limited Warranty
For warranty details call 1-800-353-2729
•Illuminated display
Easy to read your settings in dark places
•Talk Hands-Free (VOX)
“Voice act ivation” (VOX ) lets you talk
hands-free when used with optional
accessories
•Multiple Audible Call Tones
Multiple distinct ringing options so your
group can identify who’s calling
•Button Beeps (on/off)
Silences the beeps to avoid disturbing
others
•Batteries (not included)
Requires 3 AA Alkaline batteries or one
NiMH rechargeable battery
•User’s guide included
•Accessories for T6200 series - Convenient headphones, some with hands-free talk capabilities, mesh and waterproof carry
cases, and rechargeable battery packs available from your retailer or www.motorola.com