TLKR T60/T61
OWNER'S MANUAL
RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS
ATTENTION!
Before using this product, read the RF Energy Exposure and
Product Safety Guide that ships with the radio which contains
instructions for safe usage and RF energy awareness and
control for compliance with applicable standards and regulation.
Package Contents
• 2 x TLKR T60/T61 Radio
• 2 x Belt Clip
• 1 x Charging Cradle
• 1 x AC Adapter
• 2 x Battery support brackets
• 2 x Rechargeable NiMH battery packs
• TLKR T60/T61 Owner's Manual
Frequency Chart
Ch. Freq. (MHz) Ch. Freq. (MHz) Ch. Freq. (MHz)
1 446.00625 4 446.04375 7 446.08125
2 446.01875 5 446.05625 8 446.09375
3 446.03125 6 446.06875
Features and Specifications
• 8 PMR Channels
• 121 Sub-Codes (38 CTCSS Codes & 83 DCS codes)
• Up to 8 km Range*
• Internal VOX Circuitry
• 5 Selectable Call Tone Alerts
• Backlit LCD Display
• Headset Jack for Optional Headset
• Roger Beep
•Up Timer
• Room Monitor
• Battery Charger
• Battery Level Meter
• Channel Monitor
• Channel Scan
•Dual Watch
• Keypad Lock
•Auto Power Off
• Power Source: NiMH battery Pack / 4 AAA Alkaline batteries
• Battery Life: 16 Hours (under typical use conditions)
*Range may vary depending on environmental and/or topographical
conditions.
English
1
Control and Functions
Antenna
PTT
(Push-To-Talk)
Button
Headset jack
(Headset not included)
(Volume/Channel Up) Button
(Call) Button
MON (Monitor) Button
Speaker
Microphone
(Volume/Channel
Down) Button
SEL/ (Select/Lock)
Button
MENU/(Menu/
Power Button)
DC IN 9V Jack
English
2
Display
1
2
3
4
5
6
9
10
7
8
11
12
Installing the Battery
1. Make sure your radio is turned OFF.
2. To remove the battery compartment door, press the tab at the bottom of the compartment door.
3. Install the NiMH batteries into the battery compartment.
4. Replace the battery compartment door.
English
Battery Level and Low Battery Alert
Indicates that the battery is fully charged.
Blinks when battery is low; charge the radio
or replace batteries immediately.
Charging the Radio
Using the Charging Cradle :
1. Make sure your radio is turned OFF.
2. Connect the AC adapter to the DC IN 9V of the charging
1. Dual Watch Indicator
2. Transmit/Receive Indicator
3. Channel Indicator
4. Volume Level Indicator
5. VOX/Room Monitor Indicator
6. Scan Indicator
7. Battery Level Meter
8. Sub-code Indicator
9. Up timer Indicator
10.APO (Auto Power Off) Indicator
11.Keypad Lock Indicator
12.Call Tone Indicator
cradle.
3. Place the charging cradle on a stable surface.
4. Place the radio in the charging cradle with the keypad facing forward.
5. LED indicator will illuminate and remain illuminated as long as the radio is in the charger.
Note: Charge the battery pack for 16 hours.
Using the Battery Support Bracket :
1. Remove the rechargeable NiMH battery pack from the radio.
2. Place the battery support bracket into the charging cradle.
3. Install the NiMH battery pack into the charging cradle. Ensure that the charging contacts are correctly aligned.
4. LED indicator will illuminate and remain illuminated as long as the radio is in the charger.
Note: Charge the battery pack for 16 hours.
3
Battery Capacity Maintenance
1. Charge the batteries at least once every 3 months when not in use.
2. Remove the battery from the radio after using for storage purpose.
English
3. Store the batteries in temperatures between -20°C to 35°C and in low humidity. Avoid damp conditions and corrosive materials.
Basic Radio Operations
Read this reference guide completely before attempting to
operate the unit.
Turning your Radio On/Off
Press and hold the MENU/ button to turn your radio ON/OFF.
Adjusting the Volume
Adjust the volume by pressing the and buttons.
Adjusting the Sound (Key Beeps)
Your radio emits a beep each time one of the buttons is pressed
(except the PTT and button).
Press and hold the button while turning the radio ON to
switch the sound ON/OFF.
Navigating through the Menu
Your radios has two Menu functions: Select Menu and Mode
Menu.
1. To enter the Select Menu, press the SEL/ button.
2. To enter the Mode Menu, press the MENU/ button.
3. Additional presses of the SEL/ button or MENU/ button will advance you through the Menu.
4. To exit the Menu function, do one of the following :
4
a. Press and hold the MENU/ button.
b. Press and hold the PTT, MON or the button.
c. Wait 10 seconds until the unit automatically returns to
“Normal” mode.
Talking on Your Radio
1. Hold your radio 5–8 cm from your mouth.
2. Press and hold the PTT button while speaking. The appears on the display.
3. Release the PTT button. You can now receive incoming
calls. When you do, the appears on the display. To
respond, repeat procedure from step 1.
Note: When you continue to transmit for 60 seconds, the
radio emits TX Time Out tone and the icon
flashes. The radio will stop transmitting.
In order to speak to someone, both your radios must
be set to the same channel and Sub-Code. Refer to
“Selecting a Channel and a Sub-Code” below.
Selecting a Channel and a Sub-Code
To select a Channel:
1. SEL/ button to enter Select Menu. Advance until the Channel indicator blinks.
2. or to the required channel.
To select a Sub-code :
1. SEL/ button to enter Select Menu. Advance until the Sub-code indicator blinks.
2. or to the required Sub-code.
3. Exit the Select Menu.
Select Menu
Normal
Channel Sub-code VOX Level Call Tone
Auto Power
Off
Normal
1 - 8 0 - 121 OFF, 1 - 5 1 - 5
Off / 60 /
120 / 180
Your radio navigates through the Select Menu as follows:
English
Voice Operated Transmission (VOX)
Transmission is initiated by speaking into the microphone of
radio or headset (headset is not included) i nstead of the
pushing the PTT button.
To select the VOX level:
1. SEL/ button to enter Select Menu. Advance until blinks.
2. or to the desired VOX sensitivity level.
3. Exit the Select Menu.
Note: Level oF(OFF) disables VOX. Levels 1-5 set the
sensitivity of the VOX circuit.Use level 1 in quiet
environments, and use level 5 in very noisy
environments. You can find the appropriate
sensitivity level by speaking into the microphone. If
the flashes, your voice is accept ed.
Transmitting a Call Tone
Your radio is equipped with 5 selectable call tones.
To select a call tone:
1. SEL/ button to enter Select Menu. Advance until blinks.
2. or to the desired call tone.
3. Exit the Select Menu.
To transmit the selected call tone :
1. to transmit the selected call tone. The selected tone will automatically be transmitted for a fixed length of time.
2. PTT to cancel Call Tone.
Auto Power Off
Auto Power Off feature allows you to set the time that the radio
turns off automatically.
1. SEL/ button to enter Select Menu. Advance until and the current Auto Power Off time blinks.
2. or to select the time from oF (Off), 60, 120 and 180 minutes.
3. Exit the Menu.
5
Mode Menu
Select the
Sensitivity
Normal
Scan Mode
Dual Watch
Mode
Room Monitor
Mode
Up Timer
Mode
Select the Channel
and Sub-Code
Normal
Up Timer
Mode
Room Monitor
Mode
Dual Watch
Mode
Scan Mode
Your radio navigates through Mode Menu as follows:
English
Features on Your Radio
Channel Scan Mode
Enables your radio to scan for active channels. When activity is
detected, your radio lands (stays) on that channel
(for 2 seconds). To transmit on that channel, press the PTT
button. When activity on the landed channel ends, your radio
continues scanning other channels.
To turn the channel scan ON:
1. MENU/ to enter Mode Menu. Advance until blinks.
2. SEL/ to turn ON channel scan.
3. MENU/ , or PTT to turn OFF Scan mode.
6
Dual Watch Mode
Enables your to scan the current channel and another channel
alternately.
To set another channel and start Dual Watch:
1. MENU/ to enter Mode Menu. Advance until blinks.
2. or to select the channel, then press SEL/ .
3. or to select the Sub-code, then press SEL/ .
4. The radio starts to Dual Watch.
Note: If you set the same channel and Sub-code as the
current channel, Dual Watch doesn’t work.
5. MENU/ to turn the Dual Watch mode OFF.
Room Monitor
Enables your radio to detect voice/noises (according to the
sensitivity level set) and transmit back to the listening radio
without pushing the PTT button. The monitoring radio is not
able to receive any transmissions in this mode.
To turn Room Monitor ON:
1. MENU/ to enter Mode Menu. Advance until blinks.
2. or to the desired room monitor sensitivity level.
Note: Use level 1 in quiet environments. Use level 5 in very
noisy environments.
3. SEL/ to turn ON room monitor.
MENU/ to turn OFF Room Monitor.
Note: When the voice/noise in the monitored room
continues for more than 60 seconds, the monitoring
radio stop monitoring for 5 seconds, and resumes.
Up Timer
Enables your radio to time up to 39 minutes 59 seconds. You
can receive incoming calls in this mode.
To use up timer:
1. MENU/ to enter Mode Menu. Advance until blinks.
2. SEL/ to select the Up Timer.
3. to start the Up Timer.
4. MENU/ , , MON or PTT to stop or reset up timer.
Key Lock
Press and hold SEL/ until appears to lock the keypad.
Press and hold SEL/ until disappears to unlock the
keypad.
LCD Backlight
The LCD display will automatically illuminate for 10 seconds
after any button is pressed (except for PTT).
Monitor Mode
Enables you to listen for weak signals on the current channel.
To turn the Monitor Mode ON:
1. Press the MON button for brief listening. The icon blinks.
2. Press and hold the MON button for 2 seconds for continuous
listening. The icon continues to blink.
To turn the Monitor Mode OFF:
Press the MON, button to return to “Normal” mode. The icon
stops blinking.
Roger Beep
Sounds to indicate the end of a PTT or VOX transmission. It
can be heard through the spe aker when Key Beep is on. It
cannot be heard through the speaker if Key Beep is turned off.
Press and hold the button while turning the radio ON to turn
the Roger Beep ON. Repeat the step to turn Roger Beep OFF.
Automatic Power Save
For better battery life, your radio is designed to switch to Power
Save mode when there has been no transmissions after 3
seconds. The radio can receive transmissions in this mode.
English
7
Warranty Information
The authorized Motorola dealer or retailer where you purchased
your Motorola two-way radio and/or original accessories will
honour a warranty claim and/or provide warranty service.
Please return your radio to your dealer or retailer to claim your
English
warranty service. Do not return your radio to Motorola.
In order to be eligible to receive warranty service, you must
present your receipt of purchase or a comparable substitute
proof of purchase bearing the date of purchase. The two-way
radio should also clearly display the serial number. The
warranty will not apply if the type or serial numbers on the
product have been altered, deleted, removed, or made illegible.
What Is Not Covered By The Warranty
• Defects or damage resulting from use of the Product in other
than its normal and customary manner or by not following
the instructions in this user manual.
• Defects or damage from misuse, accident or neglect.
• Defects of damage from improper testing, operation, maintenance, adjustment, or any alteration or modification of any
kind.
• Breakage or damage to aerials unless caused directly by
defects in material or workmanship.
• Products disassembled or repaired in such a manner as to
adversely affect performance or prevent adequate inspection and testing to verify any warranty claim.
• Defects or damage due to range.
• Defects or damage due to moisture, liquid or spills.
• All plastic surfaces and all other externally exposed parts
that are scratched or damaged due to normal use.
• Products rented on a temporary basis.
• Periodic maintenance and repair or replacement of parts
due to normal usage, wear and tear.
8
Copyright Information
The Motorola products described in this manual may include
copyrighted Motorola programs, stored semiconductor
memories or other media. Laws in the United States and other
countries preserve for Motorola, certain exclusive rights for
copyrighted computer programs, including the exclusive right to
copy or reproduce in any form, the copyrighted Motorola
programs.
Accordingly, any copyrighted Motorola computer programs
contained in the Motorola products described in this manual
may not be copied or reproduced in a ny manner without
express written permission of Motorola. Furthermore, the
purchase of Motorola products shall not be deemed to grant
either directly or by implicatio n, estoppel, or otherwise, any
license under the copyrights, patents or patent applications of
Motorola, except for the normal non-exclusive royalty free
license to use that arises by operation of law in the sale of a
product.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the
Stylized M logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their
respective owners.
© 2012, 2013 Motorola Solutions, Inc. All rights reserved.
1
M
*68015000924*
68015000924-B
2
Loading...