Motorola SBV5220 User Manual

User Guide
SBV5220 VoIP Cable Modem
Introduction Installation Troubleshooting Glossary License

Safety and Regulatory Information

WARNING: T O PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT.
CAUTION: THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS. TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERF ACE CABLES AND INSTALL THEM PROPERLY.
CAUTION: DIFFERENT TYPES OF CORD SETS MA Y BE USED FOR CONNECTIONS T O THE MAIN SUPPLY CIRCUIT. USE ONLY A MAIN LINE CORD THAT COMPLIES WITH ALL APPLICABLE PRODUCT SAFETY REQUIREMENTS OF THE COUNTRY OF USE.
CAUTION: TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER UL LISTED OR CSA CERTIFIED TELECOMMUNICATION LINE CORD, OR NATIONAL EQUIVALENT.
CAUTION: INSTALLATION OF THIS PRODUCT MUST BE IN ACCORDANCE WITH NATIONAL WIRING CODES AND CONFORM TO LOCAL REGULATIONS.
CAUTION: DO NOT OPEN THE UNIT . DO NOT PERFORM ANY SER VICING OTHER THAN THA T CONTAINED IN THE INST ALLATION AND TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: CHANGES AND MODIFICATIONS NOT EXPRESSLY APPROVED BY MOTOROLA FOR COMPLIANCE COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IMPORT ANT SAFETY INSTRUCTIONS: When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
Read all of the instructions listed here and/or in the user manual before you operate this equipment. Give
particular attention to all safety precautions. Retain the instructions for future reference.
This device must be installed and used in strict accordance with manufacturer’s instructions as described in
the user documentation that comes with the product.
Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols
that are affixed to this equipment.
Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a
wet basement, or near a swimming pool.
Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC
outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.
Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of
the power cord.
Place unit to allow for easy access when disconnecting the power cord of the device from the AC wall outlet.
Do not connect the plug into an extension cord, receptacle, or other outlet unless the plug can be fully
inserted with no part of the blades exposed.
SBV5220 VoIP Cable Modem User Guide ii
Introduction Installation Troubleshooting Glossary License
Place this equipment on a stable surface.
Postpone cable modem installation until there is no risk of thunderstorm or lightning activity in the area.
It is recommended that the customer install an AC surge protector in the AC outlet to which this device is
connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, and disconnect the cable system. This will prevent damage to the product due to lightning and power surges.
Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from
excessive heat and humidity and keep the device free from vibration and dust.
Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners
directly on the unit or use forced air to remove dust.
Avoid damaging the cable modem with static by touching the coaxial cabl e when it is attached to the earth-
grounded coaxial cable-TV wall outlet.
Always first touch the coaxial cable connector on the cable modem when disconnecting or re-connecting USB
or Ethernet cable from the cable modem or the user’s PC.
Operate this product only from the type of power source indicated on the product’s marking label. If you are
not sure of the type of power supplied to your home, consult your dealer or local power company.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for possible special disposal instructions.
Disconnect the phone wire (RJ-11 cable) and unplug the power cable before removing the cover.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks
to determine that the product is in safe operating condition. SAVE THESE INSTRUCTIONS. Be sure that the outside cable system is grounded, so as to provide some protection against voltage surges and
built-up static charges. Article 820-40 of the NEC (Section 54, Part I of the Canadian Electrical Code) provides guidelines for proper grounding and, in particular, specifies the CATV cable ground shall be connected in the grounding system of the building, as close to the point of cable entry as practical.
Caring for the Environment by Recycling
When you see this symbol on a Motorola product, do not dispose of the product with residential or commercial waste.
Recycling your Motorola Equipment
Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local authorities for information about practices establishe d for your region. If collection systems are not available, call Motorola Customer Service for assistance.
SBV5220 VoIP Cable Modem User Guide iii
Introduction Installation Troubleshooting Glossary License

Safety Requirements for the SBV5220 Lithium-Ion Battery

You must properly handle the SBV5220 lithium-ion rechargeable battery to ensure your safety . Improper handling can cause leakage, heat, smoke, explosion, or fire resulting in damage to the equipment or the user.
Use the SBV5220 battery only in the SBV5220 VoIP cable modem.
CAUTION: Risk of explosion if battery is replaced by the incorrect type. Use only Motorola approved
batteries, Motorola part number 515757-001. Dispose of used batteries according to the instructions.
Do not use the battery where static electricity is generated.
Do not heat the battery or discard into a fire. Keep the battery away from high-temperature locations.
Properly discard the battery if it exhibits an abnormal condition, such as heat, odor, color, or a change in
shape. When discarding, place insulated tape over the battery terminals.
The battery should be stored out of the reach of children.
Do not store the battery close to metal objects.
If the battery leaks fluid and you touch it, immediately wash your hands. If the fluid gets into your eye, do not
rub the eye. Rinse with water and immediately seek medical care. Left untreated, the battery fluid could cause
damage to the eye.
Ensure that the battery does not receive any strong impacts, such as dropping or striking with a hard object.
At the end of battery life, the SBV5220 battery must be disposed of properly and may need to be recycled.
Contact your local recycling center for proper disposal methods.
Do not expose the battery to ultrasonic energy.
Do not disassemble, modify, or attempt to repair the battery.
Before installation, the battery should not be subjected to temperatures below –10ºC or above +60ºC (14º F
to 140º F). After initial customer usage (initially charged above shipping charge state), the battery should not
be subjected to temperatures outside the operating temperature range:
Battery Pack External Exposure Operating Temperature Range:
Charging: 0.0°C to +45.0°C (0º F to 113º F)
Discharging: –10.0°C to +60.0°C (14º F to 140º F)
SBV5220 VoIP Cable Modem User Guide iv
Introduction Installation Troubleshooting Glossary License

Important VoIP Service Information

Any services provided through this equipment:
Are not intended to replace or be a substitute for primary line voice services or Plain Old
Telephon e Service (POTS).
Are not meant to provide guaranteed 911 or E911 services or to permit access to 411
directory assistance services.
IMPORTANT: When using this VoIP device, you CANNOT make any calls, including an emergency call, and E911 location services WILL NOT be available, under the following circumstances:
Your broadband ISP connection goes down, is lost or otherwise fails.
You lose electrical power.
When using this VoIP device, you may be able to make an emergency call to an operator, but E911 location services may not be available under the following circumstances:
You have changed the physical address of your VoIP device, and you did not update or
otherwise advise your VoIP service provider of this change.
You are using a non-U.S. telephone number.
There are delays in making your location information available in or through the local
automatic location information database. Note: Your service provider, not Motorola, is responsible for the provision of VoIP telephony services through this equipment. Motorola shall not be liable for, and expressly disclaims, any
direct or indirect liabilities, damages, losses, claims, demands, actions, causes of action, risks or harms arising from or related to the services provided through this equipment.

Regulatory Information

FCC Compliance Class B Digital Device

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicati o n s. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tu rning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Canada - Industry Canada (IC)
This Class B digital device complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
SBV5220 VoIP Cable Modem User Guide v
Introduction Installation Troubleshooting Glossary License

FCC Declaration of Conformity

According to 47CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers, Motorola, Inc. Connected Home Solutions Business, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole responsibility that the product identifies with 47CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variatio n accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde sired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47CFR, Paragraph 15.101 to 15.109.

International Declaration of Conformity

We,
Motorola, Inc. Connected Home Solutions Business 101 Tournament Drive Horsham, PA, U.S.A.
declare under our sole responsibility that the
SBV5220
to which the declaration relates is in conformity with one or more of the following standards:
EN55022 EN55024 EN60950 EN61000-3-2 EN61000-3-3 CISPR 22 CISPR 24 IEC 60950 3rd Edition ETSI EN 300386
the following provisions of the Directive(s) of the Council of the European Union:
EMC Directive 89/336/EEC Low Voltage Directive 73/23/EEC Directive 93/68/EEC
Models Standards
SBV5220, SBV5220 Diagnostic FCC Part 15, ICES-003
SBV5220i, SBV5220 Diagnostic EN55022, EN55024, CISPR22, CISPR24,
UL/C-UL 60950 3rd Edition
EN61000-3-2, EN61000-3-3, EN60950-2000, IEC60950 3rd Edition, ETSI EN 300386
SBV5220 VoIP Cable Modem User Guide vi
Introduction Installation Troubleshooting Glossary License

Regulatory, Safety, Software License, and Warranty Information Card

This product is provided with a separate Regulatory , Saf e ty, Software License, and Warranty Information card. If one is not provided with this product, please ask your service provider or point-of-purchase representative, as the case may be.
THIS PRODUCT IS IN COMPLIANCE WITH ONE OR MORE OF THE STANDARDS LISTED ON THE
REGULATORY, SAFETY, SOFTWARE LICENSE, AND WARRANTY INFORMATION CARD. NOT ALL STANDARDS APPLY TO ALL MODELS.
NO WARRANTIES OF ANY KIND ARE PROVIDED BY MOTOROLA WITH RESPECT TO THIS PRODUCT,
EXCEPT AS STATED ON THE REGULATORY, SAFETY, SOFTWARE LICENSE, AND WARRANTY INFORMATION CARD. MOTOROLA’S WARRANTIES DO NOT APPLY TO PRODUCT THAT HAS BEEN REFURBISHED OR REISSUED BY YOUR SERVICE PROVIDER.
Copyright © 2006 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as
translation, transformation or adaptation) wit hout written permission from Motorola, Inc. Motorola reserves the right to revise this publication and to make changes in content from time to time withou t obligat ion on the part of Motorola to
provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me, and Windows NT are registered trademarks and Microsoft Corporation. Macintosh is a registered trademark of Apple Computer, Inc. CableLabs and DOCSIS are a registered trademarks and PacketCable is a trademark of Cable Television Laboratories, Inc. Linux is a registered trademark of Linus Torvalds. Solaris, Java, and all Java-based marks trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. Adobe and Acrobat Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the U.S. and/or other countries. trademark of Netscape Communications Corporation.
product or service names are the property of their respective owners. © Motorola, Inc. 2006.
All other
SBV5220 VoIP Cable Modem User Guide vii
Windows XP is a trademark of
UNIX is a registered trademark of the Open Group in the United States and other countries.
Microsoft Corporation. Microsoft Windows screen shots are used by permission of
Navigator is a registered
Introduction Installation Troubleshooting Glossary License

Contents

Safety and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Safety Requirements for the SBV5220 Lithium-Ion Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Important VoIP Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
FCC Compliance Class B Digital Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
FCC Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
International Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Regulatory, Safety, Software License, and Warranty Information Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SBV5220 VoIP Cable Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SBV5220 VoIP Telephone Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Telephone Features Supported by the SBV5220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Top and Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Signing Up for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Computer System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ethernet Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cabling and Startup for a Single User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setting Up a USB Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Setting Up a USB Driver in Windows 98 Second Edition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Setting Up a USB Driver in Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Setting Up a USB Driver in Windows Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Setting Up a USB Driver in Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Configuring TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Configuring TCP/IP in Windows 98, Windows 98 Second Edition, orWindows Me . . . . . . . . . . . . . . . . . . . . . . . .22
Configuring TCP/IP in Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Configuring TCP/IP in Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Verifying the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Verifying the IP Address in Windows 98, Windows 98 Second Edition, or Windows Me . . . . . . . . . . . . . . . . . . . .32
Verifying the IP Address in Windows 2000 or Wi ndows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Renewing Your IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Cabling for Multiple Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ethernet and USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Wall Mounting the SBV5220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Wall Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Front-Panel Lights and Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
SBV5220 VoIP Cable Modem User Guide viii
Introduction Installation Troubleshooting Glossary License
Removing the USB Driver from Windows 98 Second Edition or Windows Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Removing the USB Driver from Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Removing the USB Driver from Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Running the Motorola USB Driver Removal Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Software License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SBV5220 VoIP Cable Modem User Guide ix

Introduction

Introduction Installation Troubleshooting Glossary License
Congratulations on your new Motorola SBV5220 Voice over Internet Protocol (VoIP) cable modem! It provides high-speed access to the Internet and other online services, and connections for up to two telephone lines.

SBV5220 VoIP Cable Modem

Your SBV5220 V oIP cable modem transmits and receives data much faster than traditional dial-up or DSL (digital subscriber line) modems. It lets you enjoy surfing the Web without the long wait. Because many network and other factors can affect performance, the actual speed will vary.
Unlike a dial-up modem, your SBV5220 VoIP cable modem is always online. Just open your browser and surf! Y ou can use your high-speed, upgradeable VoIP cable modem to connect one or more computers in your home or
business to the Internet. You can connect:
A single computer equipped with a Universal Serial Bus (USB) port directly to the USB port on the SBV5220
VoIP cable modem
A single computer equipped with an Ethernet adapter directly to the Ethernet port on the SBV5220 VoIP cable
modem
Two computers, one to the USB port and one to the Ethernet port
Up to 31 computers to a single SBV5220 VoIP cable modem using an Ethernet hub, as shown in “Cabling for
Multiple Users” on page 35
For easiest set-up, use the Installation Assistant on the SBV5220 VoIP Cable Modem CD-ROM.

SBV5220 VoIP Telephone Service

The SBV5220 also provides telephone service through your cable connection with the same features as your traditional phone service, including standby power with an integrated battery backup in the event that you lose AC power. You can connect up to two standard telephone lines using your SBV5220 VoIP cable modem, supporting:
Local and long-distance calling
Standby power support for a minimum of six hours standby or four hours talk time
Standard telephone feature support. For a full listing, see “Tele phone Features Supported by the SBV5220”
on page 2.
Telephon e modem and fax support
HTML diagnostic page
Software upgrades over the network to provide new or improved services
Caution
Use only a standard telephone. Digital phones used in many businesses that connect to a PBX (private branch exchange) do not operate with the SBV5220.
SBV5220 VoIP Cable Modem User Guide 1
Introduction Installation Troubleshooting Glossary License

Telephone Features Supported by the SBV5220

The SBV5220 supports the telephone features listed below. Some features listed may not be available on your telephone. Feature availability may also be determined by your telephone service provider.
Standard two-wire telephone connection for voice, fax, and telephone modem operation. The connection to
the telephone equipment is made with a standard RJ-11 jack and plug.
Re-dial number
Speed dial
Call forwarding
Call hold and mute
Call return
Call waiting
Caller ID
Caller ID block
Three-way calling
Voice mail
Telephony Devices for the Disabled (TDD)
On hook, off hook detection
Operator barge-in
Standard call progress signals
Dial-tone stutter
Dial-tone busy
Fast-busy stutter dial-tone call waiting
No support for pulse-dial equipment
SBV5220 VoIP Cable Modem User Guide 2
Introduction Installation Troubleshooting Glossary License

Top and Front Panel

For added security, you can press the Standby button (1) to suspend your Internet connection. No data is transmitted or received from the Internet when the Standby light is on. All other front-panel lights turn off until you press the Standby button again, except for Tel 1 and Tel 2.
The model number on your VoIP
cable modem may be different
than in the illustrations and
screen images in this guide.
The lights provide information about power, communications, and errors:
Key Light Flashing On
2Power Startup diagnostics in progress. VoIP cable modem powered on. 3 DS (downstream) Scanning for a receive (downstream)
channel connection.
4 US (upstream) Scanning for a send (upstream)
channel connection.
5Online Scanning for a network connection. Startup process completed. 6Link Transmitting or receiving data. A device, such as a computer or hub, is connected to
7Tel 1 Connected and activated,
telephone is off-hook (in use).
8Tel 2 Connected and activated,
telephone is off-hook (in use).
9 Battery AC power not present. Normal condition indicating that AC power present and
10 Standby This light does not flash. Internet service blocked because the Standby button
During normal operation, the Power, DS, US, and Online lights are on and the Link light flashes when the VoIP cable modem is transferring data.
Downstream channel connected.
Upstream channel connected.
the USB or Ethernet connectors on the back panel. Connected and activated, the telephone is on-hook
(not in use). Connected and activated, the telephone is on-hook
(not in use).
the battery is in good condition.
was pressed. If this light is on, all other lights are off, except for Tel 1 and Tel 2.
SBV5220 VoIP Cable Modem User Guide 3
Introduction Installation Troubleshooting Glossary License

Rear Panel

The rear panel provides cabling connectors and the power receptacle:
Key Item Description
1 & 2 Tel 1 and Tel 2 Telephone port s 1 and 2 provide connections for two telephone lines. 3POWER Provides AC power to the VoIP cab le modem. 4 ETHERNET Provides the connection to Ethernet equipped computers using a cable terminated with an
RJ-45 connector.
5USB Provides the connection to USB equipped computers. 6 Reset If you experience a problem, you can push this recessed button to reset the VoIP cable modem
(see “Troubleshooting” on page40). Resetting may take some time (5 to 30 minutes) because the VoIP cable modem must find and lock on the appropriate communications channels.
7 CABLE Provides the connection to the coaxial cable (coax) outl et.
SBV5220 VoIP Cable Modem User Guide 4
Introduction Installation Troubleshooting Glossary License

Before You Begin

Before you begin the installation, check that you received the following items with your VoIP cable modem:
Item Description
Power adapter or cable
10/100Base-T Ethernet cable
USB cable Connects to the USB port
Phone wire Connects the telephone to the cable system to provide telephone service
SBV5220 VoIP Cable Modem
CD-ROM
Connects to the AC power outlet
Connects to the Ethernet port
Contains the User Guide and USB drivers
Battery Provides standby power for your SBV5220 (one each). The SBV5220 has
the capability to accommodate two st andby batteries. For additional stan dby batteries, contact your service provider.
You will need 75-ohm coaxial cable with F-type connectors to connect your VoIP cable modem to the nearest cable outlet. If a TV is connected to the cable outlet, you may need a 5–900 MHz RF splitter and a total of three coaxial cables to connect both the TV and the VoIP cable modem. The coaxial cable and RF splitter are available at consumer electronics stores. To connect your VoIP cable modem to an Ethernet hub, see the network description in “Cabling for Multiple Users” on page 35. Check the documentation provided with your hub.
Caution
This product is for indoor use only. Do not route the USB, Ethernet, or telephone cables outside of the building. Exposure of the cables to lightning could create a safety hazard and damage the product.
SBV5220 VoIP Cable Modem User Guide 5
Introduction Installation Troubleshooting Glossary License

Precautions

Postpone VoIP cable modem installation until there is no risk of thunderstorm or lightning activity in the area. To avoid damaging the VoIP cable modem with static electricity:
Always first connect the coaxial cable to the grounded cable TV wall outlet.
Before you connect or disconnect the USB or Ethernet cable from your VoIP cable modem or PC, always
touch the coaxial cable connector on the VoIP cable modem to release any static charges.
To avoid damaging your VoIP cable modem or PC with static electricity:
Before you connect or
disconnect the USB or
Ethernet cable, touch the
coaxial cable connector on
the VoIP cable modem.
To prevent overheating the VoIP cable modem, do not block the ventilation holes. Do not open the VoIP cable modem. Refer all service to your cable provider. Wipe the VoIP cable modem with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray
cleaners directly on the unit or use forced air to remove dust.
Always make the wall connection first.
Caution
Contact your cable provider before connecting your VoIP cable modem to your existing telephone wiring. Do not connect the telephone wire to a traditional telephone (PSTN) service.
SBV5220 VoIP Cable Modem User Guide 6
Introduction Installation Troubleshooting Glossary License

Signing Up for Service

You must sign up with a cable provider to access the Internet and other online services. To activate your servic e, call your local cable provider.
T o receive data service, you need to provide the MAC address printed on the bar code label marked HFC MAC ID on the back of the cable modem. You can record it here:
00 : ______ : ______ : ______ : ______ : ______
To receive telephone service, you need to provide the MAC address printed on the bar code label marked MTA MAC ID on the back of the cable modem. You can record it here:
00 : ______ : ______ : ______ : ______ : ______
You should ask your cable provider the following questions:
Do you have any special system requirements?
When can I begin to use my VoIP cable modem?
Are there any files I need to download after I am connected?
Do I need a user name or password to access the Internet or use e-mail?
SBV5220 VoIP Cable Modem User Guide 7
Introduction Installation Troubleshooting Glossary License

Computer System Requirements

You can use any Web browser, such as Microsoft® Internet Explorer or Netscape Navigator®, with your SBV5220 VoIP cable modem.
For Microsoft Windows computers, the Installation Assistant application automatically checks your system configuration. CD-ROM.
Your SBV5220 VoIP cable modem is compatible with Microsoft Windows®, Macintosh®, UNIX®, and Linux computers. Windows® 95 is not supported by the SBV5220.
You must have the latest version of your operating system installed with all current service packs and patches.

Ethernet Card

You can use the Ethernet connection with any Windows, Macin tosh, UNIX, or Linux computer equipped with a 10Base-T or 10/100Base-T Ethernet card.
The original version of Windows connection.
If you use an Ethernet card, it must be installed in your computer before you install your SBV5220 VoIP cable modem. If it is not installed, follow the installation instructions provided with your Ethernet card.
You can start the Installation
®
98, Windows® NT, UNIX, Linux, or Macintosh computers must use the Ethernet
Assistant from the Main Menu on the SBV5220 VoIP Cable Modem
®

USB Connection

You can use the USB connection with any PC running Windows® 98 Second Edition, Windows® 2000, Windows
®
Me
, or Windows XP™ that has a USB interface. The USB connection requires special USB driver software that is
supplied on the SBV5220 VoIP Cable Modem CD-ROM. You can upgrade your USB drivers from our Downloads page http://broadband.motorola.com/noflash/
usb_drivers.asp.
SBV5220 VoIP Cable Modem User Guide 8
Introduction Installation Troubleshooting Glossary License

Battery Installation

Before you begin the installation, you must first install the battery in your VoIP cable modem. Please read “Safety
Requirements for the SBV5220 Lithium-Ion Battery” on page iv before proceeding.
1 Place the SBV5220 on its side and remove the battery cover on the bottom.
Battery Installation
2
Slide the battery into the battery compartment until it is fully seated. The battery is keyed so that it cannot be installed incorrectly. Make sure that the pull-tab on the battery is accessible and does not prevent the battery cover from closing properly.
3 Re-install the battery cover with the locking tabs seated downward, and then push the cover forward.
It may take up to 12 hours to reach full charge when:
The battery is installed for the first time.
The battery is replaced.
The battery is fully discharged.
SBV5220 VoIP Cable Modem User Guide 9
Introduction Installation Troubleshooting Glossary License

Installation and Configuration

To install and configure your Motorola VoIP cable modem for a single PC running Microsoft Window s, we recommend using the
SBV5220 VoIP Cable Modem
Motorola VoIP cable modem. Otherwise, to install and configure your Motorola VoIP cable modem:
1 Connect the cables as described for your situation:
“Cabling and Startup for a Single User” on page 10
“Cabling for Multiple Users” on page 35
2 If you are using the USB port only, go to “Setting Up a USB Driver” on page 12. Ethernet users can skip this
step.
3 Configure TCP/IP and verify the IP address for your computer as described for yo ur situation:
For Windows computers, see “Configuring TCP/IP” on page 22.
Refer to your Macintosh or UNIX user manual for information regarding TCP/IP and IP address
configuration.
Installation
Assistant.
CD-ROM. In most cases, the Installation
You can start the Installation
Assistant from the Main Menu on the
Assistant automatically configures your

Cabling and Startup for a Single User

Allow some time (5 to 30 minutes) to power up the first time because the Motorola VoIP cable modem must find and lock on the appropriate channels for communications.
Always connect coaxial cable to the wall outlet first.
To electrical outlet (step 4)
To cable outlet (step 2)
1 Be sure your computer is on and the Motorola VoIP cable modem is unplugged. 2 Connect one end of the coaxial cable to the cable outlet or splitter. Connect the other end of the coaxial cable
to the CABLE connector on the Motorola VoIP cable modem. Hand-tighten the connectors to avoid damaging them.
3 Insert the SBV5220 VoIP Cable Modem CD-ROM into your CD-ROM drive. 4 Plug the AC power cord into the connector on the Motorola VoIP cable modem and an unswitched AC
electrical outlet. This turns on the Motorola VoIP cable modem. You do not need to unplug it when not in use.
SBV5220 VoIP Cable Modem User Guide 10
Introduction Installation Troubleshooting Glossary License
Check that the lights on the front of the Motorola VoIP cable modem cycle through this sequence:
5
Power flashes during the self-test and changes to solid green when the self-test is successfully complete.
Receive flashes while scanning for the receive (downstream) channel and changes to solid green when it
is connected.
Send flashes while scanning for the send (upstream) channel and changes to solid green when it is
connected.
Online flashes while the Motorola VoIP cable modem downloads configuration data and changes to solid
green when the download is complete.
6 Connect your computer to the Motorola VoIP cable modem using USB or Ethernet:
Either/or
ComputerMotorola VoIP cable
USB: Be sure the SBV5220 VoIP Cable Modem CD-ROM is inserted in your CD-ROM drive. Perform the appropriate procedure for Setting Up a USB Driver for your Windows version. Connect the USB cable to the USB port on the Motorola VoIP cable modem. Connect the other end to the USB port on your PC.
Ethernet:
cable modem. Connect the other end to the Ethernet port on your computer. Ethernet users do not need to set up USB.
Connect the provided straight-through Ethernet cable to the Ethernet connector on the Motorola VoIP
SBV5220 VoIP Cable Modem User Guide 11
Introduction Installation Troubleshooting Glossary License
Perform the procedures for “Configuring TCP/IP” on page 22.
7 8 To connect the telephone line, plug a phone wire into the Tel 1 connector. You can also connect a second
telephone line to the Tel 2 connector.
Either/or
Caution!
To reduce the risk of fire, use only No. 26 or larger UL Listed or CSA Certified Telecommunication Line Cord or national equivalent to connect a telephone line to your Motorola VoIP cable modem.
Do not connect both the Ethernet and USB cables to the same computer. Connect to either Ethernet or USB.
Contact your cable provider before connecting your Motorola VoIP cable modem to your existing telephone wiring. Do not connect the telephone wire to a traditional telephone (PSTN) service.
Be sure the phone connectors are neither connected together nor connected to wall jacks on the same network.

Setting Up a USB Driver

The following subsections describe setting up a USB driver. Before connecting a PC to the USB port, perform the appropriate procedure for your Windows version:
“Setting Up a USB Driver in Windows 98 Second Edition” on page 13
“Setting Up a USB Driver in Windows 2000” on page 17
“Setting Up a USB Driver in Windows Me” on page 20
“Setting Up a USB Driver in Windows XP” on page 21
When you finish setting up the USB driver, you can continue with “Configuring TCP/IP” on page 22. The Motorola VoIP cable modem USB driver does not support Macintosh or UNIX computers. For those systems,
you can connect through Ethernet only.
Caution!
Be sure the SBV5220 VoIP Cable Modem CD-ROM is inserted in the CD-ROM drive before you plug in the USB cable.
SBV5220 VoIP Cable Modem User Guide 12
Introduction Installation Troubleshooting Glossary License
Setting Up a USB Driver in Windows 98 Second Edition
1 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers
and must be inserted and read by the PC before you connect the Motorola VoIP cable modem to the PC.
2 Connect the Motorola VoIP cable modem to your computer with a USB cable. For further instructions, see
“Cabling and Startup for a Single User” on page 10. A few seconds after you complete the USB connection,
the Add New Hardware Wizard window is displayed:
3 Click Next. The following window is displayed:
SBV5220 VoIP Cable Modem User Guide 13
Introduction Installation Troubleshooting Glossary License
Be sure “Search for the best driver for your device” is selected and click Next. The following window is
4
displayed:
5 Be sure “CD-ROM drive” is the only box selected. Click Next.
The message “Please wait while Windows searches for a new driver for this device” is displayed. If your computer successfully locates the driver, skip to step 8. If your computer does not locate the driver, the previous window is displayed again.
6 Select Specify a location and type the location of your CD-ROM drive.
To load the driver successfully, you may need to click Browse to manually select the NetMotCM.sys file from the CD-ROM.
SBV5220 VoIP Cable Modem User Guide 14
Introduction Installation Troubleshooting Glossary License
Click Next. The following window is displayed:
7
8 Select The updated driver... and click Next.
If this window is not displayed, verify that the SBV5220 VoIP Cable Modem CD-ROM is properly inserted in the CD-ROM drive. If you still cannot find the correct driver file, click Cancel to cancel the installation and perform the procedure for “Removing the USB Driver from Windows 98 Second Edition or Windows Me” on page 42. Then repeat this procedure.
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
SBV5220 VoIP Cable Modem User Guide 15
Introduction Installation Troubleshooting Glossary License
After the window shown under step 8 is displayed, click Next.
9
If a window with the message Copying Files... displays and asks for your CD-ROM drive, type your CD-ROM drive letter (for example, “D:”) and click OK.
If an Insert Disk window similar to the following is displayed, Windows system files are needed to complete the installation. T o install the files, insert your Windows 98 Second Edition CD-ROM in the CD-ROM drive and click OK.
After all the necessary files are loaded, the following window is displayed confirming a successful installation:
10 Click Finish. The Systems Settings Change window is displayed:
11 Click Yes to restart your computer.
When you finish setting up the USB driver, you can continue with “Configuring TCP/IP in Windows 98, Windows
98 Second Edition, or Windows Me” on page 22.
If you have difficulties setting up the USB driver, perform “Removing the USB Driver from Windows 98 Second
Edition or Windows Me” on page 42 and repeat this procedure. If that does not correct your problem , see the
Regulatory, Safety, Software License, and Warranty Information card provided with your Motorola VoIP cable modem for information about obtaining warranty service.
SBV5220 VoIP Cable Modem User Guide 16
Introduction Installation Troubleshooting Glossary License

Setting Up a USB Driver in Windows 2000

1 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers
and must be inserted and read by the PC before you connect the Motorola VoIP cable modem to the PC.
2 Connect the Motorola VoIP cable modem to your computer with a USB cable. For further instructions, see
“Cabling and Startup for a Single User” on page 10. A few seconds after you complete the USB connection,
the Found New Hardware Wizard window is displayed:
3 Click Next. The following window is displayed:
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
Be sure “Search for a suitable driver for my device” is selected.
SBV5220 VoIP Cable Modem User Guide 17
Introduction Installation Troubleshooting Glossary License
Click Next. The following window is displayed:
4
Be sure “CD-ROM drives” is the only box selected.
5 Click Next. The following window is displayed:
6 Click Next.
If the Insert Disk window is displayed, be sure the SBV522 0 VoIP Cable Modem CD-ROM is in the CD-ROM drive and follow steps 7 to 11. Otherwise, if the Completing the Found New Hardware window is displayed, you can skip to step 12.
SBV5220 VoIP Cable Modem User Guide 18
Introduction Installation Troubleshooting Glossary License
On the Insert Disk window, click OK. The Files Needed window is displayed:
7
8 If necessary, select your CD-ROM drive in the “Copy files from” list. 9 Click Browse. 10 Double-click the NetMotCM.sys file in the CD-ROM root directory. The Files Needed window is displayed: 11 Click OK. The Found New Hardware Wizard window is displayed:
12 Click Finish to complete the installation.
When you finish setting up the USB driver, you can continue with “Configuring TCP/IP in Windows 2000” on page 25.
If you have any difficulties setting up the USB driver, perform “Removing the USB Driver from Windows 2000” on page 43 and repeat this procedure.
SBV5220 VoIP Cable Modem User Guide 19
Introduction Installation Troubleshooting Glossary License
Setting Up a USB Driver in Windows Me
1 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers
and must be inserted and read by the PC before you connect the Motorola VoIP cable modem to the PC.
2 Connect the Motorola VoIP cable modem to your computer with a USB cable. For further instructions, see
“Cabling and Startup for a Single User” on page 10. A few seconds after you complete the USB connection,
the Add New Hardware Wizard window is displayed:
3 Click Next. Windows automatically searches for the correct USB drivers and installs them. If the installation is
successful, the following window is displayed. Otherwise, be sure the SBV5220 VoIP Cable Modem CD-ROM is correctly inserted in your CD-ROM drive.
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
4 Click Finish to complete the installation.
When you finish setting up the USB driver, you can continue with “Configuring TCP/IP in Windows 98, Windows
98 Second Edition, or Windows Me” on page 22.
SBV5220 VoIP Cable Modem User Guide 20
Introduction Installation Troubleshooting Glossary License
Setting Up a USB Driver in Windows XP
1 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers
and must be inserted and read by the PC before you connect the Motorola VoIP cable modem to the PC.
2 Connect the Motorola VoIP cable modem to your computer with a USB cable. For further instructions, see
“Cabling and Startup for a Single User” on page 10. A few seconds after you complete the USB connection,
the Found New Hardware Wizard window is displayed:
3 Be sure “Install the software automatically” is selected. 4 Click Next. Windows automatically searches for the correct USB drivers and installs them. If the installation is
successful, the following window is displayed:
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
5 Click Finish to complete the installation. Otherwise, be sure the SBV5220 VoIP Cable Modem CD-ROM is
correctly inserted in your CD-ROM drive.
When you finish setting up the USB driver, you can continue with “Configuring TCP/IP in Windows XP” on page 28.
SBV5220 VoIP Cable Modem User Guide 21
Introduction Installation Troubleshooting Glossary License

Configuring TCP/IP

The Motorola VoIP cable modem contains all required software. You do not need to configure the Motorola VoIP cable modem, but you must be sure that your computer is configured for TCP/IP (a protocol for communication between computers). Perform one of the following:
“Configuring TCP/IP in Windows 98, Windows 98 Second Edition, or Windows Me” on page 22
“Configuring TCP/IP in Windows 2000” on page 25
“Configuring TCP/IP in Windows XP” on page 28
Follow the instructions in your Macintosh or UNIX user manual
After configuring TCP/IP, perform one of the following to verify the IP address:
“Verifying the IP Address in Windows 98, Windows 98 Second Edition, or Windows Me” on page 32
“Verifying the IP Address in Windows 2000 or Windows XP” on page 33
Follow the instructions in your Macintosh or UNIX user manual
Your cable provider may provide additional instructions to set up your computer.
Configuring TCP/IP in Windows 98, Windows 98 Second Edition, or Windows Me
1 On the Windows Desktop, click Start. 2 Select Settings and then Control Panel from the pop-up menus. 3 Double-click the Network icon on the Control Panel window. The Network window is displayed:
4 Select the Configuration tab. 5 Verify that TCP/IP is installed for the adapter that will be used to connect to the Motorola VoIP cable modem
by looking for TCP/IP. If found, TCP/IP is installed. Skip to step 10. If TCP/IP is not installed for the adapter, continue with step 6.
SBV5220 VoIP Cable Modem User Guide 22
Introduction Installation Troubleshooting Glossary License
Select the adapter to be used for the SBV5220 VoIP cable modem connection and then click Add. The Select
6
Network Component Type window is displayed:
7 Select the Protocol option and click Add. The Select Network Protocol window is displayed:
8 Click Microsoft in the Manufacturers section and click TCP/IP in the Network Protocol section of Select
Network Protocol window.
9 Click OK. 10 Click TCP/IP on the Network window. If there is more than one TCP/IP entry, choose the one for the Ethernet
card or USB port connected to the Motorola VoIP cable modem.
SBV5220 VoIP Cable Modem User Guide 23
Introduction Installation Troubleshooting Glossary License
Click Properties. The TCP/IP Properties window is displayed:
11
12 Click the IP Address tab. 13 Click Obtain an IP address automatically. 14 Click OK to accept the TCP/IP settings. 15 Click OK to close the Network window. 16 Click OK when prompted to restart your computer and click OK again.
When you complete TCP/IP configuration, go to “Verifying the IP Address in Windows 98, Windows 98 Second
Edition, or Windows Me” on page 32.
SBV5220 VoIP Cable Modem User Guide 24
Introduction Installation Troubleshooting Glossary License
Configuring TCP/IP in Windows 2000
1 On the Windows Desktop, click Start. 2 Select Settings and then Control Panel from the pop-up menus. The Control Panel window is displayed:
In the steps that follow, a connection number such as 1, 2, or 3 is a reference displayed on PCs with multiple network interfaces. PCs having only one network interface may display only the label
Local Area Connection
3 Double-click the Network and Dial-up Connections icon on the Control Pa nel window. The Network and
Dial-up Connections window is displayed:
4 Double-click Local Area Connection number. The value of number varies from system to system. The Local
Area Connection number Status window is displayed:
.
SBV5220 VoIP Cable Modem User Guide 25
Introduction Installation Troubleshooting Glossary License
Click Properties. The Local Area Connection Properties window is displayed:
5
6 If Internet Protocol (TCP/IP) is in the list of components, TCP/IP is installed. You can skip to step 10.
If Internet Protocol (TCP/IP) is not in the list, click Install. The Select Network Component Type window is displayed:
7 Click Protocol on the Select Network Component Type window and click Add. The Select Network Protocol
window is displayed:
8 Click Internet Protocol (TCP/IP) in the Network Protocol section on the Select Network Protocol window.
SBV5220 VoIP Cable Modem User Guide 26
Introduction Installation Troubleshooting Glossary License
Click OK. The Local Area Connection number Properties window is re-displayed:
9
10 On the Local Area Connection number Properties window, be sure the box next to Internet Protocol
(TCP/IP) is selected.
11 Click Properties. The Internet Protocol (TCP/IP) Properties window is displayed:
12 Be sure Obtain IP address automatically and Obtain DNS server address automatically are selected.
Click OK to accept the TCP/IP settings.
13 Click OK to close the Local Area Connection number Properties window. 14 Click OK when prompted to restart your computer and click OK again.
When you complete the TCP/IP configuration, go to “Verifying the IP Address in Windows 2000 or Windows XP” on page 33.
SBV5220 VoIP Cable Modem User Guide 27
Introduction Installation Troubleshooting Glossary License
Configuring TCP/IP in Windows XP
1 On the Windows desktop, click Start to display the Start window shown.
2 Click Control Panel to display the Control Panel window. The display varies, depending on your Windows XP
view options. If the display is a Category view as shown below, continue with step 3. Otherwise, skip to step 5.
SBV5220 VoIP Cable Modem User Guide 28
Introduction Installation Troubleshooting Glossary License
Click Network and Internet Connections. The Network and Internet Connections window is displayed:
3
4 On the Network and Internet Connections window, click Network Connections to display the LAN or
high-speed Internet connections. Skip to step 6.
5 If a Classic view similar to below is displayed, click Network Connections to display the LAN or high-speed
Internet connections.
SBV5220 VoIP Cable Modem User Guide 29
Introduction Installation Troubleshooting Glossary License
Right-click your network connection. If more than one connection is displayed, be sure to select the one for
6
your network interface.
7 Select Properties from the pop-up menu. The Local Area Connection Properties window is displayed:
SBV5220 VoIP Cable Modem User Guide 30
Introduction Installation Troubleshooting Glossary License
Select Internet Protocol (TCP/IP) and click Properties to display the Internet Protocol (TCP/IP) Properties
8
window:
9 On the Internet Protocol (TCP/IP) Properties window, verify that the settings are correct, as shown. 10 Click OK to close the TCP/IP Properties window. 11 Click OK to close the Local Area Connection Properties window.
When you complete the TCP/IP configuration, go to “Verifying the IP Address in Windows 2000 or Windows XP” on page 33.
SBV5220 VoIP Cable Modem User Guide 31
Introduction Installation Troubleshooting Glossary License

Verifying the IP Address

The following subsections describe verifying an IP address. Perform the appropriate procedure for your Windows version:
“Verifying the IP Address in Windows 98, Windows 98 Second Edition, or Windows Me” on page 32
“Verifying the IP Address in Windows 2000 or Windows XP” on page33
For a Macintosh or UNIX system, refer to your user guide.
Verifying the IP Address in Windows 98, Windows 98 Second Edition, or Windows Me
To check the IP address:
1 On the Windows Desktop, click Start. 2 Select Run. The Run window is displayed. 3 Type winipcfg.exe and click OK. A window similar to the example is displayed:
The example values for Adapter Address, IP Address, Subnet Mask, and Default Gateway on your PC will be different than in the image above.
In Windows 98 Second Edition, if IP Autoconfiguration Address is displayed before Adapter Address, call your service provider.
4 Select your adapter name — the Ethernet card or USB device. 5 Click Renew. 6 Click OK after the system displays an IP address.
If after performing this procedure your computer cannot access the Internet, call your cable provider for help.
SBV5220 VoIP Cable Modem User Guide 32
Introduction Installation Troubleshooting Glossary License

Verifying the IP Address in Windows 2000 or Windows XP

To check the IP address:
1 On the Windows Desktop, click Start. 2 Select Run. The Run window is displayed. 3 Type cmd and click OK. 4 Type ipconfig and press ENTER to display your IP configuration. A display, like below, indicates a normal
configuration:
If an Autoconfiguration IP Address is displayed as in the window below, there is an incorrect connection between your PC and the Motorola VoIP cable modem or there are cable network problems.
Check:
Your cable connections
Whether you can see cable-TV channels on your television
After successfully verifying your cable connections and proper cable-TV operation, you can renew your IP address.
SBV5220 VoIP Cable Modem User Guide 33
Introduction Installation Troubleshooting Glossary License

Renewing Your IP Address

To renew your IP address:
1 On the Windows Desktop, click Start. 2 Select Run. The Run window is displayed. 3 Type cmd and click OK. 4 Type ipconfig /renew and press ENTER. If a valid IP address is displayed as shown, Internet access should
be available.
5 Type exit and press ENTER to return to Windows.
If after performing this procedure your computer cannot access the Internet, call your cable provider for help.
SBV5220 VoIP Cable Modem User Guide 34
Introduction Installation Troubleshooting Glossary License

Cabling for Multiple Users

The Motorola VoIP cable modem supports several multiple-user configurations. Along with an optional hub or router, it can serve as an Internet gateway for up to 31 computers.
Not all service providers support multiple-user service. For information about multiple-user service, contact your cable provider.

Ethernet and USB

You can connect the USB port on one computer and the Ethernet port on another computer directly to the Motorola VoIP cable modem, as shown.
Cable outlet
Coaxial cable
Motorola VoIP
cable modem
USB cable
Ethernet cable
Computer
Computer
Caution
Do not connect both the Ethernet and USB cables to the same computer.
You can connect a single computer to the USB port and from one to 31 remaining us ers to an Ethernet hub, as shown. You cannot connect more than one computer to the Motorola VoIP cable modem through the USB port.
Cable outlet
Coaxial cable
Motorola VoIP
cable modem
USB cable
Computer
Ethernet cables
Ethernet cable
Ethernet hub
or switch
ComputerComputerComputer
SBV5220 VoIP Cable Modem User Guide 35
Introduction Installation Troubleshooting Glossary License

Ethernet

Y ou can connect up to 31 computers to an Ethernet hub connected to a SBV5220 Motorola VoIP cable modem, as shown.
Cable outlet
Coaxial cable
Motorola VoIP
cable modem
Ethernet cable
Ethernet hub
or switch
Ethernet cable
ComputerComputerComputer
SBV5220 VoIP Cable Modem User Guide 36
Introduction Installation Troubleshooting Glossary License

Wall Mounting the SBV5220

If you mount your SBV5220 on the wall, you must:
Locate the unit as specified by the local or national codes governing residential or business cable TV and
communications services.
Follow all local standards for installing a network interface unit/network interface device (NIU/NID).
If possible, mount the SBV5220 to concrete, masonry, a wooden stud, or other very solid wall material. Use anchors if necessary, for example, if you must mount the unit on drywall.
To mount yo ur SBV5220 on the wall:
1 If present, remove the four rubber chassis feet on the bottom of the SBV5220 as indicated.
2 Print the Wall Mounting Template on page 39.
While viewing the Wall Mounting Template, click the Print icon or choose Print from the File menu to display the Print dialog box. (The following image is from Adobe
may be slight differences in your version). Under Print Range, select Current page. Be sure you print the template at 100% scale. Page scaling should
be set to None (100%). Click OK to print the template.
®
Acrobat® Reader® running on Windows XP; there
SBV5220 VoIP Cable Modem User Guide 37
Introduction Installation Troubleshooting Glossary License
Measure the printed template with a ruler to ensure that it is the correct size.
3 4 Use a center punch to mark the center of the holes. 5 On the wall, locate the marks for the mounting holes.
Caution
Before drilling holes, check the structure for potential damage to water, gas, or electric lines.
6 See step 6 for recommended mounting hardware size. Drill holes to a depth and diameter appropriate for the
size and type of hardware you have selected.
7 If necessary, install an anchor in each hole.
Use M3.5 x 38 mm (#6 x 1 1/2 inch) screws with a flat underside and maximum screw head diameter of 9.0 mm (.35 inches) to mount the SBV5220.
8 Using a screwdriver, turn each screw until the head protrudes from the wall, as shown:
— There must be at least 2.5 mm (.10 inches) between the wall and the underside of the screw head. — The maximum distance from the wall to the top of the screw head is 6.0 mm (.24 in)
Note: Example above for mounting SBV5220 on a wood surface.
9 Place the SBV5220 so the keyholes are above the mounting screws. 10 Slide the SBV5220 down so it stops against the top of the keyhole opening.
SBV5220 VoIP Cable Modem User Guide 38
Introduction Installation Troubleshooting Glossary License

Wall Mounting Template

You can print this page to use as a wall mounting template.
Be sure you print it at 100% scale. Page scaling should be set to None (100%). Measure the printed template with a ruler to ensure that it is the correct size
SBV5220 VoIP Cable Modem User Guide 39
Introduction Installation Troubleshooting Glossary License

Troubleshooting

If the solutions listed here do not solve your problem, contact your cable provider. Before calling your service provider, try pressing the reset button on the rear panel or unplugging and plugging in the VoIP cable modem power cord. Resetting the VoIP cable modem may take 5 to 30 minutes. Your service provider may ask for the status of the front-panel lights as described in “Front-Panel Lights and Error Conditions” on page 41.
Problem Possible Solutions
Green POWER light is off
No telephone service
Cannot send or receive data
Check that the power cord is properly plugged into the electrical outlet and the VoIP cable
modem.
Check that the electrical outlet is working.
If the Standby light is on, the Internet connection is off. Press the Standby button to
reconnect to the Internet.
Check the connection between the SBV5220 and your telephone.
If your telephone requires external power, check the AC power connection for your
telephone.
Check the coaxial cable on the SBV5220 and the electrical outlet. Hand-tighten the cable
connectors if necessary.
Check the lights on the front panel. Make sure the green power light is on. If it is not, check
that the power cord is properly plugged into the electrical outlet and the VoIP cable modem.
If you have cable TV, check that your TV is working and the picture is clear. If you cannot
receive your regular TV channels, your telephone service will not func tion.
Check the lights on the front p an el. Not e the fi rst li ght f rom top t o botto m that is off. This light
indicates where the error occurred, as described in “Front-Panel Lights and Error
Conditions” on page 41.
If all lights are off except the Standby and Tel 1/Tel 2 lights, the VoIP cable modem is in
Standby mode. Press the Standby button to reconnect your Internet service. The Standby button does not affect the Tel 1/Tel 2 LEDs.
If you have cable TV, check that your TV is working and the picture is clear. If you cannot
receive your regular TV channels, your data service will not function.
Check the coaxial cable on the SBV5220 and the electrical outlet. Hand-tighten the cable
connectors if necessary.
Check the IP address. Follow the steps in “Verifying the IP Address in Windows 98, Windows 98 Second Edition, or Windows Me” on page 32 or “Verifying the IP Address in Windows 2000 or Windows XP” on page 33. Call your cable provider if you need an IP
address.
Check that the USB or Ethernet cable is properly connected to the VoIP cable modem and
your computer.
Problems related to unsuccessful USB driver installation
SBV5220 VoIP Cable Modem User Guide 40
Remove the USB driver. Follow the instructions in one of:
• “Removing the USB Driver from Windows 98 Second Edition or Windows Me” on page 42
• “Removing the USB Driver from Windows 2000” on page 43
• “Removing the USB Driver from Windows XP” on page 45
Then perform “Running the Motorola USB Driver Remov al Utility” on page 48.
Introduction Installation Troubleshooting Glossary License

Front-Panel Lights and Error Conditions

Light Turns Off During Startup If Turns Off During Normal Operation If
Power The VoIP cable modem is not properly plugged
into the power outlet
Battery AC power is not present. AC power is not present. DS
(Receive) US
(Send) Online IP registration is unsuccessful The IP registration is lost Tel 1 or
Tel 2
The receive channel cannot be acquired The receive channel is lost
The send channel cannot be acquired The send channel is lost
If the Tel light fails to flash during startup, telephone line configuration has failed.
The VoIP cable modem is unplugged or is in standby mode. Plug it in or press the Standby button.
Connected during a phone call and does not blink, telephone connection is lost.
If a telephone line is properly connected and the Tel 1 or Tel 2 light remain s off, the line has not been set up for service. Contact your service provider.
For more information about the lights, see “Top and Front Panel” on page 3.
SBV5220 VoIP Cable Modem User Guide 41
Introduction Installation Troubleshooting Glossary License
Removing
1 On the Windows Desktop, right-click one of:
the USB Driver from Windows 98 Second Edition or Windows Me
In Windows 98 Second Edition, the Network Neighborhood icon
In Windows Me, the My Network Places icon
The Network window is displayed:
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
2 Click the Motorola SURFboard USB Cable Modem and click Remove. The Network window no longer
displays Motorola SURFboard USB Cable Modem in the list:
SBV5220 VoIP Cable Modem User Guide 42
Introduction Installation Troubleshooting Glossary License
Click OK. The System Settings Change window is displayed:
3
4 Disconnect the USB cable from your computer or VoIP cable modem. 5 Click Yes to restart your computer. 6 Perform “Running the Motorola USB Driver Removal Utility” on page 48.
Removing
1 On your Windows desktop, click Start. 2 Click Settings. 3 Double-click Control Panel to display the Control Panel window:
the USB Driver from Windows 2000
4 Double-click System to display the System Properties window.
SBV5220 VoIP Cable Modem User Guide 43
Introduction Installation Troubleshooting Glossary License
Click the Hardware tab:
5
6 Click Device Manager to display the Device Manager window:
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
7 Double-click Network Adapters. 8 Click the Motorola SURFboard USB Cable Modem. The Uninstall icon is displayed on the window near the
top.
9 Click Uninstall. A window is displayed. 10 Click OK. 11 Close the Device Manager and Control Panel windows. 12 Perform “Running the Motorola USB Driver Removal Utility” on page 48.
SBV5220 VoIP Cable Modem User Guide 44
Introduction Installation Troubleshooting Glossary License
Removing the USB Driver from Windows XP
1 On the Windows desktop, click Start to display the Start window shown.
2 Click Control Panel to display the Control Panel window. The display varies, depending on your Windows XP
view options.
SBV5220 VoIP Cable Modem User Guide 45
Introduction Installation Troubleshooting Glossary License
If a Category view similar to the image under step 2 is displayed, click Performance an d Maintenance.
3
Otherwise, skip to step 5.
4 Click System to display the System Properties window. Skip to step 6. 5 If a Classic view similar to the following is displayed, click System to display the System Properties window:
SBV5220 VoIP Cable Modem User Guide 46
Introduction Installation Troubleshooting Glossary License
Click the Hardware tab to display the Hardware page:
6
7 Click Device Manager to display the Device Manager window:
Although your Motorola VoIP cable modem model number may be different than in the images in this guide, the procedure is the same.
8 Double-click Network adapters. 9 Click the Motorola SURFboard USB Cable Modem. The Uninstall icon is displayed on the window near the
top. Click Uninstall.
10 Close the Device Manager window and Control Panel windows. 11 Perform “Running the Motorola USB Driver Removal Utility” on page 48.
SBV5220 VoIP Cable Modem User Guide 47
Introduction Installation Troubleshooting Glossary License
Running the Motorola USB Driver Removal Utility
Before running the Motorola USB Driver Removal Utility, you must run the Windows Device Manager by performing one of:
“Removing the USB Driver from Windows 98 Second Edition or Win dows Me” on page 42
“Removing the USB Driver from Windows 2000” on page 43
“Removing the USB Driver from Windows XP” on page 45
To run the Mo torola USB Driver Removal Utility:
1 Insert the SBV5220 VoIP Cable Modem CD-ROM in the CD-ROM drive. After a short time, a window with
language choices is displayed.
2 Press the Esc key on the keyboard to exit the start-up screens. 3 To start Windows Explorer, click Start and select Run. On the Run window, type explorer and click OK.
Your Windows Explorer may appear different than in the image on this page. There are variations between Windows versions and you can configure Windows Explorer as you like.
4 Double-click My Computer. 5 Double-click the Motorola CD icon (D: in the image). 6 Double-click remove or remove.exe to run the Remove utility from the SBV5220 VoIP Cable Modem
CD-ROM. The Motorola USB Driver Removal window is displayed. Be sure the USB cable is disconnected.
SBV5220 VoIP Cable Modem User Guide 48
Introduction Installation Troubleshooting Glossary License
Click Remove Driver. A progress bar indicates that the driver is being removed.
7
The following window displays when the USB driver has been successfully removed:
8 Click Exit to exit the Motorola USB Driver Removal Utility .
or Y ou can click Details to display informational messages about the files that were found and deleted, similar to
the ones shown. If necessary, scroll down to view the entire list. Click OK to close the details window:
Re-install the USB driver following one of:
“Setting Up a USB Driver in Windows 98 Second Edition” on page 13
“Setting Up a USB Driver in Windows 2000” on page 17
“Setting Up a USB Driver in Windows Me” on page 20
“Setting Up a USB Driver in Windows XP” on page 21
If you continue to have problems, contact your cable provider.
SBV5220 VoIP Cable Modem User Guide 49
Introduction Installation Troubleshooting Glossary License

Contact Us

If you need assistance while working with the Motorola VoIP cable modem, contact your cable provider. For more information about customer service, technical support, or warranty claims, see the Regulatory, Safety, Software License, and Warranty Information card provided with the Motorola VoIP cable modem.
For answers to typical questions, see “Frequently Asked Questions” on page 50. For information about Motorola consumer cable products, education, and support, visit
www.broadbandmotorola.com/consumers.

Frequently Asked Questions

Q Wh at is high-speed cable Internet access?
A Cable Internet access uses cable television wires instead of telephone lines to connect to the Internet. It is
extremely fast and affordable and does not tie up telephone lines for incoming or outgoing calls and faxes.
Q Wh at is voice over Internet Protocol (VoIP)?
A VoIP uses cable television wires instead of traditional telephone lines to provide voice and fax service.
Q How fast is a VoIP cable modem?
A A cable modem offers Internet access at speeds up to 100 times faster than a traditional phone modem. You
can experience speeds of over 1,000 Kbps. Network conditions such as traffic volume and the speed of the sites you visit can affect download speeds.
Q Can I still watch cable TV while using my VoIP cable modem?
A Yes, your cable TV line can carry the TV signal while you send and receive information on the Internet.
Q What are CableLabs
®
Certified, DOCSIS®, and Euro-DOCSIS?
A CableLabs Certified, DOCSIS, and Euro-DOCSIS are the industry standards for high-speed data distribution
over cable television system networks. They are intended to ensure that all compliant VoIP cable modems interface with all compliant cable systems. Your Motorola SBV5220 VoIP cable modem is DOCSIS-, or Euro-DOCSIS certified.
Q Wh at is PacketCable?
A PacketCable
services over cable; for example, VoIP, multimedia conferencing, and interactive gaming.
is an evolving set of interface specifications for delivering advanced, real-time multimedia
Q If I have a VoIP cable modem, can I still use my old 28.8 Kbps or 56 Kbps modem?
A Y es! Although once you’ve experienced the speed of cable Internet access, you’ll never again want to wait for
traditional dial-up services.
Q I have more than one computer. Do I need more than one Motorola VoIP cable modem?
A No, not if your computers are connected on a network. The Motorola VoIP cable modem supports current
Internet connection sharing technologies to enable you to connect up to 31 computers to the Internet using a single VoIP cable modem.
SBV5220 VoIP Cable Modem User Guide 50
Introduction Installation Troubleshooting Glossary License
Do I need to change my Internet service provider (ISP)?
Q
A A broadband connection is required for high-speed Internet access and VoIP telephone service available with
your SBV5220. Contact your cable company for your specific information.
Q Do I need to subscribe to cable TV to get cable Internet access?
A No, but you will need to subscribe to cable Internet service. Some systems require that you subscribe to basic
service before you can get Internet access and/or offer a discount when you use your own VoIP cable modem. Check with your local cable company for specific information.
Q What type of technical support is available?
A For questions about your Internet service, connection, or VoIP cable modem, contact your cable provider.
Q What do I do if my Motorola VoIP cable modem stops working?
A “Troubleshooting” on page 40 provides tips to diagnose problems and simple solutions. If you continue to
have problems, contact your cable provider or Motorola as described in “Contact Us” on page 50.
SBV5220 VoIP Cable Modem User Guide 51

Glossary

Introduction Installation Troubleshooting Glossary License
coaxial cable (coax)
DOCSIS The CableLabs Data-Over-Cable Service Interface Specification defines interface standards for
download To copy a file from one computer to another. You can use the Internet to download files from a
downstream In a network, downstream describes the direction of data received by your computer from the
Ethernet The most widely used type of local area network (LAN). The most commonly installed Ethernet
expansion slot An opening in a computer where a circuit board can be inserted to add new capabilities. F-type connector A connector used to connect coaxial cable to equipment. IP address An Internet Protocol address is an identifier for a computer or device on a TCP/IP network.
MAC address The Media Access Control Address uniquely identifies each device that can be connected to an
A type of wire consisting of a center wire surrounded by insulation and a grounded shield of braided wire. The shield minimizes electrical and radio frequency interference.
cable modems and supporting equipment.
server to your home PC. A DOCSIS VoIP cable modem downloads its con figurat io n from a serv er during start-up.
Internet.
networks are called 10Base-T. 10Base-T provides transmission speeds up to 10 megabits per second (Mbps), usually over twisted-pair wire. Fast Ethernet (100Base-T) provides transmission speeds up to 100 Mbps.
Networks using TCP/IP route messages based on the destination I P address. Your cable provider assigns your VoIP cable modem an IP address to provide a continuous Internet connection.
Ethernet network. It is permanently written to r ead-only memory (ROM) at the factory and printed on the rear panel of your Motorola VoIP cable modem. You need to provide the MAC address to your cable provider .
MHz Mega Hertz. A measure of frequency - millions of cycles per second. One MHz means one million
cycles per second.
PBX A private branch exchange is a private tele phone network usually us ed within a business. Users of
the PBX share a certain number of outside lines for making telephone calls external to the PBX.
PSTN The public switched telephone network is the traditional ci rcuit-switch ed, voice-orien ted teleph one
network originally invented by Alexander Graham Bell. It is sometimes referred to as plain old telephone service (POTS).
RJ-11 The most common type of connector for household phones. RJ-45 The most common type of connector for Ethernet networks. splitter A splitter i s a device t hat divides t he signal power from an input cable equall y between two or more
signals, each carrying a selected frequency range.
TCP/IP Transmission Control Protocol/Internet Protocol is a set of standards and rules for communication
between networks.
upstream In a network, upstream describes the direction of data sent from your computer to the In ternet. UPS An uninterruptible power supply provides a battery backup to enable voice service to continue for
some time during a power outage.
SBV5220 VoIP Cable Modem User Guide 52
Introduction Installation Troubleshooting Glossary License
USB Universal Serial Bus is a computer interface for add-on devices such as printers, scanners, and
VoIP cable modems. When you connect your Motorola VoIP cable modem to the USB port, Windows 98 Second Edition and later versions automatically reco gnize the VoIP cable modem.
VoIP Voice over Internet Protocol is a method to exchange voice, fax, and other information over the
Internet. Voice and fax have traditionally been carried over traditional telephone lines using a dedicated circuit for each line. VoIP enables calls to travel as discrete data packets on shared lines.
SBV5220 VoIP Cable Modem User Guide 53
Introduction Installation Troubleshooting Glossary License

Software License

SBV5220 VoIP Cable Modem Motorola, Inc., Connected Home Solutions Business ("Motorola")
101 Tournament Drive Horsham, PA 19044
IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE (“LICENSE”) CAREFULLY BEFORE YOU INSTALL, DOWNLOAD OR USE ANY APPLICATION SOFTWARE, USB DRIVER SOFTWARE, FIRMWARE AND RELATED DOCUMENTATION (“SOFTWARE”) PROVIDED WITH MOTOROLA’S CABLE DATA PRODUCT (THE “CABLE DATA PRODUCT”). BY USING THE CABLE DATA PRODUCT AND/OR INSTALLING, DOWNLOADING OR USING ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF THIS LICENSE. UPON ACCEPTANCE, THIS LICENSE WILL BE A LEGALLY BINDING AGREEMENT BETWEEN YOU AND MOTOROLA. THE TERMS OF THIS LICENSE APPLY TO YOU AND TO ANY SUBSEQUENT USER OF THIS SOFTWARE.
IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE (I) DO NOT INSTALL OR USE THE SOFTWARE AND (II) RETURN THE CABLE DATA PRODUCT AND THE SOFTWARE (COLLECTIVELY, “PRODUCT”), INCLUDING ALL COMPONENTS, DOCUMENTATION AND ANY OTHER MATERIALS PROVIDED WITH THE PRODUCT, TO YOUR POINT OF PURCHASE OR SERVICE PROVIDER, AS THE CASE MAY BE, FOR A FULL REFUND. BY INSTALLING OR USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE PROVISIONS OF THIS LICENSE AGREEMENT.
The Software includes associated media, any printed materials, and any “on-line” or electronic documentation. Software provided by third parties may be subject to separate end-user license agreements from the manufacturers of such Software.
The Software is never sold. Motorola licenses the Software to the original customer and to any subsequent licensee for personal use only on the terms of this License. Motorola and its 3
You may:
USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only
if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred.
TERMINATE this License by destroying the original and all copies of the Sof tware (if applicable) in whatever form.
You may not:
(1) Loan, distribute, rent, lease, give, sublicense or otherwise transfer the Software, in whole or in part, to any other person, except as permitted under the TRANSFER paragraph above. (2) Copy or translate the User Guide included with the Software, other than for personal use. (3) Copy, alter, translate, decompile, disassemble or reverse engineer the Software, including but not limited to, modifying the Software to make it operate on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws.
The Product is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design, construction, operati on or mai nte nance of a ny nucl ear f acili ty. MOTOROLA AND ITS 3 PARTY LICENSORS DISCLAIM ANY EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR SUCH USES. YOU REPRESENT AND WARRANT THAT YOU SHALL NOT USE THE PRODUCT FOR SUCH PURPOSES.
Title to this Software, including the ownership of all copyrights, mask work rights, patents, trademarks and all other intellectual property rights subsisting i n the foregoin g, and all a daptat ions to and mod ifications of the forego ing shall at all times remain with Motorola and its 3 License. The Software, including any images, graphics, photographs, animation, video, audio, music and text incorporated therein is owned by Motorola or its 3 international treaty provisions. Except as otherwise expressly provided in this License, the copying, reproduction, distribution or preparation of derivative works of the Software, any portion of the Prod uct or the documentation is strictly prohibited by such laws and treaty provisions. Nothing in th is License constitutes a waiver of Motorola’s rights under United States copyright law.
This License and your rights regarding any matter it addresses are gov erned by the laws of the Commonwealth of Pennsylvania, without reference to conflict of laws principles. THIS LICENSE SHALL TERMINATE AUTOMATICALLY if you fail to comply with the terms of this License.
Motorola is not responsible for any third party software provided as a bundled application, or otherwise, with the Software. U.S. GOVERNMENT RESTRICTED RIGHTS The Product and documentation is provided with RESTRICTED RIGHTS. The use, duplication or disclosure by the
Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at 52.227-7013. The contractor/manufacturer is Motorola, Inc., Connected Home Solutions Business, 101 Tournament Drive, Horsham, PA 19044.
rd
party licensors. Motorola retains all rights not expressly licensed under this
rd
party licensors and is protected by United States copyright laws and
rd
party licensors retain the ownership of the Software.
RD
SBV5220 VoIP Cable Modem User Guide 54
Visit our website at:
www.motorola.com
526781-001 2/06
Loading...