®
Two-Way Radio
User’s Guide
KEM-ML36100-15
he MS350R is approved for use in the US only.
T
his radio floats with included NiMH battery.
T
It may not float with some AA batteries.
For More Information
For further information, you may call Motorola at 1-800-638-5119,
e-mail us at giantintl@callcenter.com or visit us on the Internet
at www.motorola.com.
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using The Radio.
The information provided in this document supersedes the general
safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
This two-way radio contains a transmitter and a receiver. To
control your exposure and ensure compliance with the general
population/uncontrolled environment exposure limits, always
adhere to the following procedure:
• Transmit no more than 50% of the time.
• To receive calls, release the PTT button.
• To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the
radio generates measurable RF energy exposure only when
transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
This Motorola two-way radio complies with the following RF
energy exposure standards and guidelines:
• United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.
• American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.
• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
MS350 Series
To ensure optimal radio performance and make sure human
exposure to radio frequency electromagnetic energy is within
the guidelines set forth in the above standards, always adhere
o the following procedures.
t
Portable Radio Operation and EME Exposure
ntenna Care
A
se only the supplied or an approved replacement antenna.
U
nauthorized antennas, modifications, or attachments could
U
amage the radio and may violate FCC regulations.
d
o NOT hold the antenna when the radio is “IN USE.” Holding
D
he antenna affects its effective range.
t
Body-Worn Operation
To maintain compliances with FCC guidelines if you wear a radio
on your body when transmitting always place the radio in a
otorola-supplied or approved clip holder, holster, case or body
M
arness for this product. Use of non-Motorola-approved
h
ccessories may exceed FCC guidelines.
a
f you do not use one of the Motorola-supplied or approved
I
body-worn accessories and are not using the radio held in the
normal use position, ensure the radio and its antenna are at
least 1 inch (2.5 cm) from your body when transmitting.
Data Operation
f applicable, when using any data feature of the radio with or
I
ithout an accessory cable, position the radio and its antenna
w
t least one inch (2.5 cm) from the body.
a
Approved Accessories
3724: Remote Speaker with Push-to-Talk Microphone
5
3725: Headset with Swivel Boom Microphone
5
3727: Ear bud with Push-to-Talk Microphone
5
53728: Flexible Ear Receiver
56320: Earpiece with Boom Microphone
lectromagnetic Interference/Compatibility
E
Note: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic
compatibility. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility
conflicts, turn off the radio in any facility where posted notices
instruct you to do so. Hospitals or health care facilities may be
using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off the radio when onboard an
aircraft. Any use of a radio must be in accordance with
applicable regulations per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends
that a minimum separation of 6 inches (15 cm) be maintained
between a handheld wireless radio and a pacemaker. These
recommendations are consistent with the independent research
by and recommendations of the U.S. Food and Drug
Administration.
People with pacemakers should:
• ALWAYS keep the radio more than 6 inches (15 cm) from
their pacemaker when the radio is turned ON.
• Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the
potential for interference.
• Turn the radio OFF immediately if there is any reason to
suspect that interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing
aids. In the event of such interference, you may want to consult
your hearing aid manufacturer to discuss alternatives.
Medical Devices – Other
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to assist
you in obtaining this information.
1
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in
the area where you drive, and always obey them. If you do use
he radio while driving, please:
t
Give full attention to driving and to the road.
•
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call
if driving conditions so require.
he use of a two-way radio while engaged in activities requiring
T
concentration may cause distraction or otherwise impair your
ability to safely participate in such activities. Always use
technology safely.
Do not place a portable radio in the area over an air bag or in the
ir bag deployment area. Air bags inflate with great force. If a
a
ortable radio is placed in the air bag deployment area and the
p
ir bag inflates, the radio may be propelled with great force and
a
ause serious injury to occupants of the vehicle.
c
Potentially Explosive Atmospheres
Turn off the radio prior to entering any area with a potentially
explosive atmosphere. Only radio types that are especially
ualified should be used in such areas as “Intrinsically Safe.”
q
o not remove, install or charge batteries in such areas. Sparks
D
n a potentially explosive atmosphere can cause an explosion or
i
fire resulting in bodily injury or even death.
ote: The areas with potentially explosive atmospheres referred
N
to above include fueling areas such as below decks on boats,
fuel or chemical transfer or storage facilities, areas where the air
ontains chemicals or particles (such as grain, dust or metal
c
powders) and any other area where you would normally be
advised to turn off your vehicle engine. Areas with potentially
explosive atmospheres are often—but not always—posted.
Blasting Caps and Areas
o avoid possible interference with blasting operations, turn off
T
the radio when you are near electrical blasting caps, in a
blasting area, or in areas posted “Turn off two-way radios.”
Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor
burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such
as burns if a conductive material—like jewelry, keys or beaded
chains— touch exposed terminals. The conductive material may
complete an electrical circuit (short circuit) and become quite hot.
Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse or other container with metal
objects.
Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received
a sharp blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the
plug will not fit the outlet, have the proper outlet installed by
a qualified electrician. An improper condition can result in a
risk of electric shock.
4. To reduce the risk of damage to the cord or plug, pull the
plug rather than the cord when disconnecting the charger
from the AC receptacle.
5. To reduce the risk of electric shock, unplug the charger from
the outlet before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock or personal injury.
7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress.
8. An extension cord should not be used unless absolutely
necessary. Use of an improper extension cord could result in
a risk of a fire and/or electric shock. If an extension cord
must be used, make sure that:
• The pins on the plug of the extension cord are the same
number, size and shape as those on the plug of the
charger.
MS350 Series
The extension cord is properly wired and in good
•
ondition.
c
The extension cord size is 18 AWG for lengths up to 100
•
eet, and 16 AWG for lengths up to 150 feet.
f
9. The supply cord of the AC adaptor cannot be replaced. If the
ord is damaged, call customer service at 1-800-638-5119 or
c
-mail us at giantintl@callcenter.com.
e
Control Buttons
Display Screen Guide
FCC Licensing Information
This Motorola radio operate s on General Mobile Radio Service
(GMRS) frequencies and is subject to the Rules and Regulations
of the Federal Communications Commission (FCC). The FCC
requires that all operators using GMRS frequencies obtain a
radio license before operating their equipment. To obtain the
FCC forms, please visit the FCC’s Web site at
wireless.fcc.gov/uls/index.htm?job=home to source form 605
and 159, which includes all the instructions you will need.
If you wish to have the document faxed or mailed, or if you have
questions, please use the following contact information:
For a fax:
Contact the
Fax-0n-Demand
system
1-202-418-0177 1-800-418-FORM
For mail service:
Call the FCC
Forms Hotline
(3676)
If you have
questions about
the FCC License:
Call the FCC
1-888-CALL-FCC
(225-5322)
hanges or modifications not expressly approved by Motorola
C
ay void the user’s authority granted by the FCC to operate this
m
adio and should not be made. To comply with FCC requirements,
r
ransmitter adjustments should be made only by or under the
t
supervision of a person certified as technically qualified to
perform transmitter maintenance and repairs in the private land
mobile and fixed services as certified by an organization
epresentative of the user of those services. Replacement of any
r
ransmitter component (crystal, semiconductor, etc.) not
t
uthorized by the FCC equipment authorization for this radio
a
ould violate FCC rules.
c
Note:
se of this radio outside the country where it was
U
intended to be distributed is subject to government regulations
and may be prohibited.
etting Started
G
aterproof
W
his radio is waterproof to IP-67 standards. It will withstand
T
ubmersion under up to 1 meter of water for up to 30 minutes.
s
The radio is resistant to water, rain, and splashes only when the
battery cover and headset accessory port are sealed. Open the
battery compartment door or headset port cover only when the
radio is dry. Use of a headset accessory should be in dry
nvironments only.
e
he charging base and AC adaptor are not waterproof. Do not
T
expose the charger to rain or snow. Charge the radios only in a
dry location. Do not place wet radios into the charging base.
nstalling the Batteries
I
Radio floats with included NiMH battery. It may not float with
some AA batteries. Each radio can use either 1 NiMH
rechargeable battery pack or 3 AA alkaline batteries and beeps
when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Remove the NiMH battery pack from the clear plastic bag
(do not disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you.
(The ribbon should be underneath the battery pack and
should wrap around the right side of the pack for easy
removal.)
5. Close the battery cover and tighten the retaining screw on
the battery door.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Insert the three AA alkaline batteries with + and - polarity as
shown inside. (The ribbon should be underneath the AA
alkaline batteries and should wrap around the right side of
the batteries.)
4. Close the battery cover and tighten the retaining screw on
the battery door.
Caution: Radio may not float with some AA batteries installed.
Radio Battery Meter
The radio battery icon shows the battery charge level, from
full to empty . When the radio has one segment left,
the radio chirps periodically or after releasing (Low Battery
Alert).
Removing the NiMH Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door to release the battery cover and
open the cover.
3. Remove the NiMH battery pack by pulling the ribbon
attached to the radio.
4. Close the battery cover and tighten the retaining screw on
the battery door.
Removing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door, release the battery cover and
open the cover.
. Gently remove each alkaline battery by easing each battery out
3
individually.
. Close the battery cover and tighten the retaining screw on
4
he battery door.
t
otes
N
• Exercise care when removing NiMH or AA batteries. Do not
use sharp or conductive tools to remove either of these
batteries.
Remove the batteries before storing the radio for extended
•
periods of time. Batteries corrode over time and may cause
permanent damage to the radio.
The battery door must be tightly closed with the screw to
•
aintain the waterproof seal of the radio.
m
Using the Battery Charger (Optional Accessory)
he battery charger provides drop-in charging convenience for
T
iMH batteries and can be placed on any flat surface, such as a
N
esk or workbench. Charge the NiMH battery overnight (at least
d
6 hours) before using it for the first time. After the initial charge,
1
an empty battery is fully charged within 14 hours.
1. Follow the steps above to install a NiMH Battery Pack.
. Plug the AC power supply cord into the jack on the desk
2
stand.
3. Plug the AC power supply into a standard wall outlet.
. With a radio facing forward, slide it into one of the charging
4
pockets.
. When charging in the battery charger, the red light on the
5
harger base will glow continuously.
c
Notes
The light will remain red after the NiMH battery pack is fully
•
harged.
c
When moving between hot and cold temperatures, do not
•
harge the NiMH battery pack until the battery temperature
c
acclimates (usually about 20 minutes).
For optimal battery life, remove the radio from the charger
•
within 16 hours. Do not store the radio while connected to
the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty .
Allow time for the battery to charge to 1 bar before
attempting to transmit a message.
• When the radio is wet from rain or snow, thoroughly dry the
surface before charging or removing the batteries.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning the Radio On and Off
In the ON position, the radio chirps and briefly shows all feature
icons available on the radio. The display screen then shows the
current channel, code and all features that are enabled.
Press and hold for 3 seconds to turn the radio on. Press and
hold for 3 seconds to turn the radio off.
Setting the Volume
Press and hold for 3 seconds, then press the or keys
until you reach a comfortable listening level.
The MS350 has 16 volume levels controlled by the keys.
1. Press to increase volume.
2. Press to decrease volume.
3. Hold or to rapidly increase volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the
same channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release .
2
MS350 Series
or maximum clarity, hold the radio two to three inches away
F
rom your mouth and speak directly into the microphone. Do not
f
over the microphone while talking.
c
alk Range
T
his radio is designed to maximize performance and improve
T
ransmission range. Do not use the radios closer than five feet
t
part.
a
ower Boost
P
o boost the radio’s power up to high power, press the top portion
T
of the button when talking. If you know your party is close by,
you can conserve the battery’s energy by pushing the lower part
of the button to use less power.
Note:
If you are on an FRS only channel (see “Channels and
requencies” tables on overleaf for details) the radio will only use
F
ow power when either portion of the is pressed.
l
onitor Button
M
Use the Monitor function to check if a channel is currently in use
by others. For maximum range performance, the Monitor
function will also help you to hear signals that are weak.
To latch the Monitor function on, Press and hold for three
seconds. When an empty channel is located, you will hear
ontinuous static and noise on that channel.
c
o turn the Monitor function off, tap a second time or press .
T
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the
adio emits a continuous warning tone and stops transmitting if
r
ou press for 60 continuous seconds.
y
Menu Options
There are 12 options you may set to your preferences. Each press
of the MENU key advances you to the next option setting. Press
the or keys to change the setting. The menu will
automatically close 5 seconds after the last press of any button.
After the last menu item, the radio exits MENU mode and returns
to operation of the radio. A press of the button while setting
any menu option will immediately save all your settings and return
to operation of the radio.
All MENU settings will revert back to the factory default values if the
battery is fully discharged or removed for more than 30 seconds.
Menus and Values
1. Channel (1-22 and 15R-22R)
2. Interference Eliminator Code (1-121 or OFF)
3. Call Tone (1-10 or OFF)
4. iVOX (ON/OFF)
5. VOX sensitivity (1-3)
6. QT Noise Filtering (ON/OFF)
7. VibraCall (ON/OFF)
8. Keypad Tones (ON/OFF)
9. Talk Confirmation Tone (ON/OFF)
10. Auto Power Off (30/60/90 minutes or OFF)
11. Repeater Channel Enable (ON/OFF)
12. Repeater Transmitted Interference Eliminator Code
Selecting the Channel
This radio has 22 simplex channels plus 8 repeater duplex
channels. Channels are shared by other radio users and channel
selection will vary based on your location. Select a channel that is
not being used from the 22 available simplex channels. Channels
8-14 are low power (FRS 0.5 watt). All other channels are GMRS.
When the radio is on a FRS 0.5 watt channel, displays. When
the radio is on a GMRS 1.5 watt channel, displays.
The 8 GMRS repeater duplex channels 15R – 22R are disabled
by default. See ”Enabling Repeater Channels” on overleaf in
order to select a repeater channel.
See the “Channels and Frequencies” tables on overleaf for
details on channel frequencies.
1. Press . The current channel setting flashes.
2. Press or and select the channel.
3. Press to save the channel setting or to continue set up.
Selecting the Interference Eliminator Code
This radio has 121 Interference Eliminator Code settings. When a
channel is in use by 2 or more groups, this feature blocks the
reception of signals that do not carry the matching tone or code.
There are 121 privacy codes. 0 is the off position, no codes are
enabled, and all users of that channel will be heard.
ee the ”Interference Eliminator Tone / Code Values” table on
S
verleaf for details on tone frequencies and code values.
o
. Press until the code starts to flash.
1
. Press or to select the code.
2
3. Press to save the code setting or to continue set up.
ou can set a different code for each channel using this
Y
procedure. An extended press of or allows you to scroll
rapidly so you can quickly reach the code you want.
This menu setting for repeater channels 15R-22R is used for
receiving only. The value must match with the repeater output.
Many repeaters will require a value of 0 or OFF. The transmitted
ode is set separately and is often required for repeater access.
c
ee ”Selecting the Repeater Access (TX) Code” on overleaf for
S
dditional information.
a
ote: You must set the Interference Eliminator Code to 0 to
N
ommunicate with radios that do not have Interference
c
Eliminator Codes.
etting and Transmitting Call Tones
S
his radio can transmit different call tones to other radios in your
T
roup so you can alert them that you want to talk. The radio has
g
10 call tones from which to choose.
o set a call tone:
T
. Press until the current call tone setting flashes and
1
ppears.
a
. Press or to change and hear the call tone.
2
. Press to set the new call tone or to continue set up.
3
To transmit your call tone to other radios set to the same
channel and Interference Eliminator Code as your radio,
ress .
p
ote: Setting the call tone to 0 disables the call tone feature.
N
ands-Free Use Without Accessories ( )
H
You can use the iVOX feature to transmit hands-free without the
need for any headset accessories. Once iVOX is turned on, the
radio detects your voice and transmits when you speak into the
internal microphone.
1. Press until appears on the display. The current
setting On/Off will flash.
2. Press or to select On or Off.
3. Press to set or to continue set up.
Hands-Free Use With Accessories ( )
You can transmit hands-free more reliably with the use of
optional headset accessories. Once VOX is turned on, the radio
detects your voice and transmits when you speak.
Many accessories (sold separately) are available for this radio. For
more information, visit our Web site at www.motorola.com or
shop.giantintl.com.
1. Turn the radio off and plug the VOX accessory into the
accessory port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by pressing or . Lower
the volume before placing the accessory on your head or in
your ear.
4. To turn off, simply remove accessory.
Notes:
• There is a short delay between the time you start talking and when
the radio transmits. There is a short delay before the transmission is
completed.
• The accessory port cover must be tightly in place to
maintain the water tight seal of the radio.
Setting the Sensitivity Level When in Mode
Adjusting the radio’s sensitivity level helps minimize the
possibility of unintended noises triggering a transmission and
helps the radio pick up soft voices.
1. Press until VOX and the level setting (1 - 3) appear on the
display.
2. Press or to select the sensitivity level.
3. Press to set or to continue set up.
3 = High Sensitivity for quiet environments
2 = Medium Sensitivity for most environments
1 = Low Sensitivity for noisy environments
ote: When you connect a headset, the radio is automatically
N
set to the last chosen sensitivity level.
oise Filtering
QTN
he Q
oise-filtering feature helps to ensure uninterrupted
T
n
T
communication with other Motorola radios that have this
feature. This feature also filters out unwanted transmissions
rom other radios. This is useful in places where there is
f
eavy radio traffic, such as amusement parks or ski resorts.
h
oise filtering is not available when the radio is
ote: Q
n
N
T
scanning.
o turn Q
T
. Press until displays. The current setting On/Off
1
oise filtering on or off:
n
T
will flash.
. Press or to turn noise filtering On or Off.
2
. Press to confirm your selection or to continue
3
et up.
s
To transmit to a radio that has Q
1. Select the same channel and Interference Eliminator
ode as the other radio.
C
. Press to send a call tone. This allows your voice to
2
ass through the Q
p
. Press and speak normally.
3
T
noise filtering turned on:
T
oise filter on the receiving radio.
n
Note: If you skip step 2, the beginning of your message may
not be heard on the receiving radio. For a 30-second period,
starting after the last transmission, all transmissions
received on the selected channel and code will pass
through the Q
VibraCallTMAlert
ibraCall
V
receiving a message. This is useful in noisy environments. When
he alert is on, the radio vibrates once every 30 seconds when
t
you receive a message on the channel and code you set.
1. To turn vibrating alerts on, press until is displayed. The
current setting will flash.
2. Press or to change the setting to On/Off.
3. Press to set or to continue set up.
Keypad Tones
You may enable or disable the speaker key tones. You will hear
the key tone each time a button is pushed.
1. Press until appears. The current setting On/Off will flash.
2. Press either or to turn On or Off.
3. Press to confirm or to continue set up.
Note: When the key tone feature is off, the following are not disabled:
• Transmit timeout alert tone
• Call tone
• Low battery alert tone or
• The transmitted talk confirmation tone
Transmitting a Talk Confirmation Tone
You can set this radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others
know you are finished talking. Talk Confirmation Tone is disabled
in repeater mode on channels 15R-22R.
1. Press until the appears. The current setting On/Off
flashes.
2. Press or to turn On or Off.
3. Press to set or to continue setup.
Auto Power Off
Your radio will save power by automatically turning itself off if
unused after a predetermined amount of time.
1. Press until displays. The current setting (0, 30, 60 or 90)
will flash.
2. Press or to set the time to 30 minutes, 60 minutes or
90 minutes. When this feature is activated, the will remain
on the display.
3. When you exit the Menu mode, the timer will begin. If a
button is pressed, or if there is an incoming signal, the timer
will restart.
4. Press to confirm or to continue set up.
Enabling Repeater Channels
Use of a repeater can greatly increase the radio range and
coverage area. Repeater use must be coordinated with the
owner of the repeater. Be sure to understand and follow the
sharing and usage rules for each repeater system.
noise filter.
T
TM
s a vibrating alert that notifies that the radio is
i
3
MS350 Series
. Press until the R appears. The current setting ON/OFF
1
ill flash.
w
. Press or to select ON or OFF.
2
. Press to save the setting or to continue set up.
3
fter enabling the repeater channels, you will be able to select
A
channels 15R-22R. Refer to the “Selecting the Channel” section
n page one.
o
Selecting the Repeater Access (TX) Code
hen a repeater channel is selected, an additional menu option is
W
vailable for setting the transmitted Interference Eliminator Code.
a
Many repeaters will require a specific value setting to activate the
epeater on your transmissions. See the table “Interference
r
Eliminator Tone / Code Values” for detailed information.
. Press repeatedly until the , the R, and the current
1
setting flash.
2. Press or to select the code.
. Press or to exit menu mode.
3
ou can set a different code for each channel using this procedure.
Y
n extended press of or allows you to scroll through the
A
Interference Code rapidly so you can quickly reach the code
you want. 0 is the off position.
Special Features
uilt-in Flashlight
B
Press and hold the flashlight button to turn and keep the light on.
The switch functions as a momentary control for the light.
Note: Turn off the flashlight when not in use to conserve battery
ower.
p
eypad Lock
K
o avoid accidentally changing the radio settings, a keypad lock
T
feature may be enabled. When in lock mode, you can only turn
the radio OFF, Receive, Transmit, send a call tone, and use the
monitor function. All other functions are locked.
1. Press and hold until icon displays.
2. To unlock the radio, press and hold until the icon is no
longer displayed.
Scanning Channels
Use scan to search the 22 channels for transmissions from unknown
parties, to find someone in your group who has accidentally changed
channels, or to quickly find unused channels for your own use.
There is a priority feature and 2 modes of scanning (basic and
advanced) to make your search more effective. The basic scan
mode uses the channel and code combinations for each of the
22 channels as you have set them (or with the default code
value of 1). The “Advanced Scan” mode will scan all channels
for any and all codes, detect any code in use, and use that code
value temporarily for that channel.
Priority is given to the “home channel,” that is, the channel (and
Interference Eliminator Code) the radio is set to when you start the
scan. This means the initial channel (and code setting) is scanned
more often than the other 21 channels, and the radio will respond
quickly to any activity occurring on the home channel as a priority.
To start Scanning:
1. Briefly press the key. The scan will appear in the
display, and the radio will begin to scroll through the channel
and code combinations.
2. When the radio detects channel activity matching the channel
and code combination, it stops scrolling and you can hear the
transmission.
3. To respond and talk to the person transmitting, press
within five seconds after the end of the transmission.
4. The radio will resume scrolling through the channels five
seconds after the end of any received activity.
5. To stop scanning, briefly press the key.
To start Advanced Scanning:
1. Set the Interference Eliminator Code to “zero” or OFF.
2. Briefly press the key. The scan will appear in the
display, and the radio will begin to scroll through the channels.
No Interference Eliminator Codes will filter what is heard.
3. When the radio detects channel activity with ANY code (or
NO code), it stops scrolling and you can hear the
transmission. Any Interference Eliminator Code that may be
in use by that party will be detected and displayed.
4. To respond and talk to the person transmitting, press within
five seconds of the end of the transmission. The radio will
transmit using the newly detected Interference Eliminator Code.
5. The radio will resume scrolling through the channels five
seconds after the end of any received activity.
. To stop scanning, briefly press the key.
6
canning Notes:
S
. If you press while the radio is scrolling through inactive
1
hannels, the transmission will be on the “home channel”.
c
Scanning will resume five seconds after the end of your
transmission. You may press the key to stop scanning at
any time.
2. If the radio stops on an undesired transmission, you may
mmediately resume the scan by briefly pressing or .
i
3. If the radio repeatedly stops on an undesired transmission,
ou may temporarily remove that channel from the scan list
y
y pressing and holding or for three seconds. You
b
ay remove more than one channel in this way.
m
. To restore the removed channel(s) to the scan list, turn the
4
adio off and then back on, or exit and re-enter the scanning
r
ode by pressing .
m
5. You cannot remove the home channel from the scan list.
. In Advanced Scan, the detected code will only be used for
6
ne transmission. You must note the code, exit scan, and set
o
hat detected code on that channel to permanently use the
t
detected code.
Weather Receiver
This radio can tune in to broadcasts by the United States National
Oceanic and Atmospheric Administration (NOAA) Weather Radio.
ou can listen to a weather channel (see “Weather Channels and
Y
Frequencies” table for details) or set the radio to alert you to
mergency weather broadcasts that interrupt routine broadcasts.
e
When you listen to a weather channel, you cannot use the radio in
can mode or for two-way communications.
s
NOAA has transmitters located throughout the United States. These
ransmitters broadcast watches, forecasts, and other information 24
t
hours a day.
ote: NOAA weather radio stations are assigned to cover specific
N
areas and service may be limited. Please check with your local
weather office for frequency and details, or visit
www.weather.gov/nwr in the US to view the appropriate transmitter
for your area.
The use of the NOAA logo does not provide an endorsement or
implied endorsement by NOAA’s National Weather Service.
Turning Weather Channel Reception On and Off
1. To turn weather reception on, press and hold for
3 seconds.
2. To turn off, press or turn the radio off and then back on.
Scanning for Weather Channel
The radio can scan for an active NOAA transmission automatically.
1. After turning weather reception on, briefly press the key.
2. The scan icon will appear in the display, and the channel
will scroll through the NOAA channels 1-7.
3. When the radio detects channel activity, it stops scanning
and you can hear the transmission.
4. You may resume the scan by briefly pressing or .
5. To stop scanning, briefly press the key. The scan
icon will disappear.
Setting the Weather Channel Manually
If you know which frequency is correct for your location, refer
to the "Weather Channels and Frequencies" table to manually
set your radio to the appropriate weather channel.
1. After turning weather reception on, press . The current
channel flashes.
2. Press or to select the appropriate channel with good
reception in your area.
3. Press to save the weather channel setting.
Setting the Weather Alert
The radio can be set to respond to NOAA Weather Radio
emergency messages. A special alarm tone sounds an alert and
turns on the weather receiver to give you immediate weather
and emergency information.
1. After turning weather reception on, press twice. ON or OFF
flashes.
2. Press or to select ON to activate. If you activate the
Weather Alert and return to two-way mode, will display.
3. Press to save the Weather Alert setting.
4. Press to return to two-way mode.
4
FRS / GMRS SIMPLEX CHANNELS AND FREQUENCIES
CHANNEL FREQ (MHz) TYPE CHANNEL FREQ (MHz) TYPE
1 462.5625 GMRS/FRS 12 467.6625 FRS
62.5875GMRS/FRS13467.6875FRS
2 4
3 462.6125 GMRS/FRS 14 467.7125 FRS
62.6375GMRS/FRS15462.5500GMRS
4 4
5 462.6625 GMRS/FRS 16 462.5750 GMRS
6 462.6875 GMRS/FRS 17 462.6000 GMRS
62.7125GMRS/FRS18462.6250GMRS
7 4
8 467.5625 FRS 19 462.6500 GMRS
9 467.5875 FRS 20 462.6750 GMRS
67.6125FRS
104
11 467.6375 FRS 22 462.7250 GMRS
MRS DUPLEX REPEATER CHANNEL FREQUENCIES
G
CHANNEL RX (MHz) TX (MHz) CHANNEL RX (MHz) TX (MHz)
15R 462.5500 467.5500 19R 462.6500 467.6500
16R 462.5750 467.5750 20R 462.6750 467.6750
7R462.6000467.600021R462.7000467.7000
1
8R462.6250467.625022R462.7250467.7250
1
EATHER CHANNELS AND FREQUENCIES
W
CHANNEL RX (MHz) CHANNEL RX (MHz) CHANNEL RX (MHz)
WX1 162.550 WX5 162.450 WX9 161.775
WX2 162.400 WX6 162.500 WX10 161.750
WX3 162.475 WX7 162.525 WX11 162.000
WX4 162.425 WX8 161.650
214
62.7000GMRS
INTERFERENCE ELIMINATOR TONE / CODE VALUES
CODE (Hz) CODE (OCTAL) CODE (OCTAL)
1 67.0 39 023 81 315
2 71.9 40 025 82 331
3 74.4 41 026 83 343
4 77.0 42 031 84 346
5 79.7 43 032 85 351
6 82.5 44 043 86 364
7 85.4 45 047 87 365
8 88.5 46 051 88 371
9 91.5 47 054 89 411
10 94.8 48 065 90 412
11 97.4 49 071 91 413
12 100.0 50 072 92 423
13 103.5 51 073 93 431
14 107.2 52 074 94 432
15 110.9 53 114 95 445
16 114.8 54 115 96 464
17 118.8 55 116 97 465
18 123.0 56 125 98 466
19 127.3 57 131 99 503
20 131.8 58 132 100 506
21 136.5 59 134 101 516
22 141.3 60 143 102 532
23 146.2 61 152 103 546
24 151.4 62 155 104 565
25 156.7 63 156 105 606
26 162.2 64 162 106 612
27 167.9 65 165 107 624
28 173.8 66 172 108 627
29 179.9 67 174 109 631
30 186.2 68 205 110 632
31 192.8 69 223 111 654
32 203.5 70 226 112 662
33 210.7 71 243 113 664
34 218.1 72 244 114 703
35 225.7 73 245 115 712
36 233.6 74 251 116 723
37 241.8 75 261 117 731
38 250.3 76 263 118 732
77 265 119 734
78 271 120 743
79 306 121 754
80 311
MS350 Series
Warranty
Consumer Two-Way Radio Products and Accessories
urchased in the United States.
p
What Does this Warranty Cover?
ubject to the exclusions contained to the right, Giant
S
International Ltd. warrants the Motorola branded consumer
wo-way radios that operate via Family Radio Service or
t
eneral Mobile Radio Service that it manufactures
G
(“Products”), the Motorola branded or certified
ccessories sold for use with these Products that it
a
manufactures (“Accessories”) to be free from defects in
aterials and workmanship under normal consumer usage
m
or the period(s) outlined below. This limited warranty is a
f
consumer’s exclusive remedy, and applies as follows to
ew Motorola branded Products and Accessories
n
manufactured by Giant International Ltd., and purchased by
onsumers in the United States, which are accompanied by
c
his written warranty:
t
Who is covered?
his warranty extends only to the first consumer purchaser,
T
nd is not transferable.
a
What will GIANT INTERNATIONAL LTD. do?
IANT INTERNATIONAL LTD., at its option, will at no charge
G
repair, replace or refund the purchase price of any
Products or Accessories that does not conform to this
warranty. We may use functionally equivalent
econditioned/ refurbished/ pre-owned or new Products,
r
Accessories or parts.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA Two-Way Radios
1-800-638-5119
giantintl@callcenter.com
For Accessories, please call the telephone number
designated above for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories at your expense, to a GIANT INTERNATIONAL
LTD. Authorized Repair Center. To obtain service, you must
include: (a) a copy of your receipt, bill of sale or other
comparable proof of purchase; (b) a written description of
the problem; (c) the name of your service provider, if
applicable; (d) the name and location of the installation
facility (if applicable) and, most importantly; (e) your
address and telephone number.
Products Covered
roducts and Accessories
P
as defined above, unless
therwise provided for
o
below.
. Consumer Two-Way
1
Radio Accessories.
2. Products and
ccessories that are
A
epaired or Replaced.
R
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS
EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN
NO EVENT SHALL MOTOROLA OR GIANT
INTERNATIONAL LTD. BE LIABLE, WHETHER IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS
OF BUSINESS, LOSS OF INFORMATION OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE
PRODUCTS OR ACCESSORIES TO THE FULL EXTENT
THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some states and jurisdictions do not allow the limitation
or exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the
above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights that vary from state to state or from one
jurisdiction to another.
Length of Coverage
ne (1) year from the date
O
of purchase by the first
onsumer purchaser of
c
the product unless
therwise provided for
o
elow.
b
. Ninety (90) days from
1
the date of purchase
y the first consumer
b
urchaser of the
p
product.
2. The balance of the
riginal warranty or
o
or ninety (90) days
f
from the date returned
o the consumer,
t
whichever is longer.
Exclusions
eriodic maintenance, repair and
ormal Wear and Tear.
N
replacement of parts due to normal wear and tear are
xcluded from coverage.
e
atteries.
B
alls below 80% of their rated capacity and batteries that
f
leak are covered by this limited warranty.
Abuse & Misuse.
mproper operation, storage, misuse or abuse, accident or
i
eglect, such as physical damage (cracks, scratches, etc.)
n
to the surface of the product resulting from misuse; (b)
ontact with liquid, water, rain, extreme humidity, heavy
c
perspiration, when the battery door or accessory port
eals are not closed, sand, dirt or the like, extreme heat, or
s
ood; (c) use of the Products or Accessories for
f
commercial purposes or subjecting the Product or
ccessory to abnormal usage or conditions; or (d) other
A
acts which are not the fault of Motorola or Giant
nternational Ltd., are excluded from coverage.
I
Use of Non-Motorola branded Products and
ccessories.Defects or damage that result from the use
A
of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded
rom coverage.
f
Unauthorized Service or Modification.
damages resulting from service, testing, adjustment,
nstallation, maintenance, alteration, or modification in
i
any way by someone other than Motorola, Giant
International Ltd. or its authorized service centers, are
excluded from coverage.
Altered Products.
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
Communication Services. Defects, damages, or the
failure of Products or Accessories due to any
communication service or signal you may subscribe to or
use with the Products or Accessories is excluded from
coverage.
nly batteries whose fully charged capacity
O
P
Defects or damage that result from: (a)
Defects or
Products or Accessories: with (a) serial
Patent and Copyright Information
Manufactured, distributed or sold by Giant International
Ltd., official licensee for this product. MOTOROLA,
MOTOROLA SOLUTIONS and the Stylized M Logo are
trademarks or registered trademarks of Motorola
Trademark Holdings, LLC and are used under license. All
other trademarks are the property of their respective
owners. ©2011 Motorola, Inc. All rights reserved.
5
MS350 Series
Loading...