Datasheet MHPM7A15S120DC3 Datasheet (Motorola)



SEMICONDUCTOR TECHNICAL DATA

 

  

Integrated Power Stage for 3.0 hp
460 VAC Motor Drive

Order this document

by MHPM7A15S120DC3/D



Motorola Preferred Device

This module integrates a 3–phase inverter, 3–phase rectifier,
brake, and temperature sense in a single convenient package. It is
designed for 3.0 hp general purpose 3–phase induction motor drive

15 AMP, 1200 VOLT

HYBRID POWER MODULE

applications. The inverter incorporates advanced insulated gate
bipolar transistors (IGBT) matched with fast soft free–wheeling
diodes to give optimum performance. The solderable top connector
pins are designed for easy interfacing to the user’s control board.

• Short Circuit Rated 10 µs @ 125°C, 720 V

• Pin-to-Baseplate Isolation Exceeds 2500 V ac (rms)

• Compact Package Outline

• Access to Positive and Negative DC Bus

• Independent Brake Circuit Connections

• UL Recognition Pending

ORDERING INFORMATION

Voltage

Device

PHPM7A15S120DC3 1200 15 3.0

MAXIMUM DEVICE RATINGS (T

Repetitive Peak Input Rectifier Reverse Voltage (TJ = 25°C to 150°C) V
Non–Repetitive Peak Input Rectifier Reverse Voltage

(TJ = 25°C to 150°C)
IGBT Reverse Voltage V
Gate-Emitter Voltage V
Continuous IGBT Collector Current (TC = 25°C) I
Repetitive Peak IGBT Collector Current
Continuous Free–Wheeling Diode Current (TC = 25°C) I
Continuous Free–Wheeling Diode Current (TC = 80°C) I
Repetitive Peak Free–Wheeling Diode Current
Average Converter Output Current (Peak–to–Average ratio of 10, TC = 95°C) I
IGBT Power Dissipation per die (TC = 95°C) P
Free–Wheeling Diode Power Dissipation per die (TC = 95°C) P
Junction Temperature Range T
Short Circuit Duration (VCE = 720 V, TJ = 125°C) t
Isolation Voltage, pin to baseplate V
Operating Case Temperature Range T
Storage Temperature Range T
Mounting Torque — Heat Sink Mounting Holes — 12 lb–in

(1) Half–Sine 60 Hz, maximum reverse voltage capability decreases by 0.1% per °C at lower temperature
(2) 1.0 ms = 1.0% duty cycle

Preferred devices are Motorola recommended choices for future use and best overall value.
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.

Rating

= 25°C unless otherwise noted)

J

Rating

(2)

(2)

Current

Rating

(1)

Equivalent

Horsepower

CASE 464D–01

ISSUE O

Symbol Value Unit

RRM

V

RSM

CES

GES

Cmax

I

C(pk)
Fmax

F80

I

F(pk)

Omax

sc

ISO

stg

D
D

J

C

900 V

1600 V

1200 V

±20 V

15 A
30 A
15 A

11.7 A
30 A
16 A
36 W
16 W

–40 to +150 °C

10

2500 Vac

–40 to +95 °C

–40 to +150 °C

m

s

Motorola IGBT Device Data

 Motorola, Inc. 1998

1

MHPM7A15S120DC3

ELECTRICAL CHARACTERISTICS

DC AND SMALL SIGNAL CHARACTERISTICS

Input Rectifier Forward Voltage (IF = 15 A) V
Gate–Emitter Leakage Current (VCE = 0 V, VGE = ±20 V) I
Collector–Emitter Leakage Current (VCE = 1200 V, VGE = 0 V) I
Gate–Emitter Threshold Voltage (VCE = VGE, IC = 1.0 mA) V
Collector–Emitter Breakdown Voltage (IC = 10 mA, VGE = 0 V) V
Collector–Emitter Saturation Voltage (IC = I
Free–Wheeling Diode Forward Voltage (IF = I
Input Capacitance (VGE = 0 V, VCE = 25 V, f = 1.0 MHz) C
Input Gate Charge (VCE = 600 V, IC = I

THERMAL CHARACTERISTICS, EACH DIE

Thermal Resistance — IGBT
Thermal Resistance — Free–Wheeling (Fast Soft) Diode
Thermal Resistance — Input Rectifier

TEMPERATURE SENSE DIODE

Forward Voltage (@ IF = 1.0 mA) V
Forward Voltage Temperature Coefficient (@ IF = 1.0 mA) TC

(T

= 25°C unless otherwise noted)

J

Characteristic

Cmax

Cmax

Symbol Min Typ Max Unit

(BR)CES

, VGE = 15 V) V

, VGE = 0 V) V

Fmax

, VGE = 15 V) Q

F
GES
CES

GE(th)

CE(sat)

F

ies

T

R

q

JC

R

q

JC

R

q

JC

F

VF

— 1.09 1.38 V
— — ±20
— 5.0 100

4.0 6.0 8.0 V

1200 — — V

— 2.5 3.5 V

1.8 2.0 2.5 V
— 2800 — pF
— 100 — nC

— 1.1 1.5 °C/W
— 2.4 3.3 °C/W
— 3.2 4.2 °C/W

1.983 2.024 2.066 V
— –8.64 — mV/°C

m

A

m

A

2

Motorola IGBT Device Data

TYPICAL CHARACTERISTICS

MHPM7A15S120DC3

30
27
24
21
18
15
12

9.0

, FORWARD CURRENT (AMPS)

6.0

F

I

3.0
0

30

25

20

TJ = 25°C

0.2 1.0

0.4 0.6

VF, FORWARD VOLTAGE (VOLTS)

0.8

1.2

Figure 1. Forward Characteristics —

Input Rectifier

VGE = 18 V 15 V

12 V

30

25

20

15

10

, FORWARD CURRENT (AMPS)

F

5.0

I

0

1.40

0

0.5 1.0 1.5 2.0 3.0
VF, FORWARD VOLTAGE (VOLTS)

TJ = 125°C 25°C

2.5

Figure 2. Forward Characteristics —

Free–Wheeling Diode

30

VGE = 18 V 15 V

25

20

12 V

15

10

, COLLECTOR CURRENT (AMPS)

5.0

C

I

0

15

10

TJ = 125°CTJ = 25°C

, COLLECTOR CURRENT (AMPS)

5.0

C

I

1.0

VCE, COLLECTOR–TO–EMITTER VOLTAGE (VOLTS)

3.02.0 4.0

5.00

0

1.0 1.5 2.5

VCE, COLLECTOR–TO–EMITTER VOLTAGE (VOLTS)

3.00.5 2.0 3.5

4.0 4.5

Figure 3. Forward Characteristics, TJ = 25°C Figure 4. Forward Characteristics, TJ = 125°C

+15 V

MBRS130T3

W

20

R

G(off)

160

R

G(on)

W

MBRS130T3

MC33153

MBRS130T3

5.00

Motorola IGBT Device Data

Figure 5. Recommended Gate Drive Circuit

3

MHPM7A15S120DC3

+15 V

TYPICAL CHARACTERISTICS

2.5

2.0

MAXIMUM
TYPICAL
MINIMUM

Figure 6. Recommended T emperature Sense

MOTOR OUTPUT

U
V

W

R1

12.4 k

14

15

21

W

A/D INPUT

Bias Circuit

1.5

1.0
TYPICAL

VF = 2.240 – 0.00864 T

0.5

, FORWARD VOLTAGE @ 1 mA (VOLTS)

F

V

MIN: 2.199 – 0.00864 T
MAX: 2.282 – 0.00864 T

0

20 40 60 80

100 120

T, TEMPERATURE (°C)

140

1600

Figure 7. BA V99LT1 Temperature Sense Diode

Performance: VF = 2.59 – 7.31E–3 T

BRAKE RESISTOR

43

65

7 8 9 10 12

11

C

R
ST3 PHASE INPUT

D1

D2

R1

SENSE

RESISTOR

Q1

Q2

24

Q3

D3

Q4

D4

23

22

R2 R3

D7

Q5

D5

TEMP

SENSE

D14

Q6

D6

21 20

19

18 17 16 15 14 13

+

C1

Q7

Figure 8. Schematic of Module, Showing Pin–Out and

External Connections

D12D10D8

D13D11D9

FILTER

R NTC

FILTER

4

Motorola IGBT Device Data

0.175

0.175

0.585

0.450

0.250

MHPM7A15S120DC3

KEEP–OUT ZONES (x4)

0.066

1.850

0.925

NOTES:

1. Package is symmetrical, except for a polarizing plastic post near pin 1,
indicated by a non–plated thru–hole in the footprint.

2. Dimension of plated thru–holes indicates finished hole size after plating.

3. Access holes for mounting screws may or may not be necessary depending on
assembly plan for finished product.

0.270

0.140

NON–PLATED

THRU–HOLE

PLATED THRU–HOLES (x24)

Figure 9. Package Footprint (Dimensions in Inches)

OPTIONAL NON–PLATED
THRU–HOLES FOR ACCESS
TO HEAT SINK MOUNTING
SCREWS (x2)

Motorola IGBT Device Data

5

MHPM7A15S120DC3

P ACKAGE DIMENSIONS

AA

M

4 PL

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. LEAD LOCATION DIMENSIONS (ie: P, Q, R, S...)
ARE TO THE CENTER OF THE LEAD.

DIM MIN MAX MIN MAX

A 111.51 112.52 4.390 4.430
B 50.93 51.94 2.005 2.045
C 12.32 13.59 0.485 0.535
D 0.89 1.65
E 8.64 9.65
F 0.13 0.64
G 5.97 6.73
H 46.48 47.50
J 0.41 1.22
K 16.26 17.27
L 3.71 4.72

M 5.46 6.48

N 10.92 11.94
P 37.60 38.60
Q 2.01 2.62
R 23.24 23.75
S 14.35 15.37
U 99.10 100.08
V 81.28 82.55

W 42.67 43.69 1.680 1.720

Y 5.15 5.77 0.203 0.227
X 11.30 12.07 0.445 0.475

AA 2.01 2.72 0.079 0.107

F

AB 16.26 17.27 0.640 0.680

0.035 0.065

0.340 0.380

0.005 0.025

0.235 0.265

1.830 1.870

0.016 0.048

0.640 0.680

0.146 0.186

0.215 0.255

0.430 0.470

1.480 1.520

0.079 0.103

0.915 0.935

0.565 0.605

3.900 3.940

3.200 3.240

DETAIL Z

INCHESMILLIMETERS

A

U

Q3 PL

Y2 PL

23

1

NPB

456

789101112

H

R

24

23 22 21 20 19 18 17 16 15 14 13

S

G 22 PL

J

DETAIL Z

D

24 PL

24 PL

AB

X

C

V

K

E

L

W

CASE 464D–01

ISSUE O

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141,

P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488

Customer Focus Center: 1–800–521–6274
Mfax: [e-mail] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

Moto rola Fax Bac k System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

– http://sps.motorola.com/mfax/

HOME PAGE: http://motorola.com/sps/

Mfax is a trademark of Motorola, Inc.

6

◊

Motorola IGBT Device Data

MHPM7A15S120DC3/D