MT 2000TM/MTS 2000TMradios combine convenient features and full alphanumeric displays into a
small, rugged package. Programmable function controls and radio-to-radio cloning provide enhanced
™
user flexibility. And you can add even more features through FLASHport
communications needs change.
software upgrades as your
3
microphones and accessories
In the case.
Out of the case.
In. Out.
It’s more efficient
to leave a radio
in place and wear a
microphone on a uniform
jacket or shirt collar —
and Motorola Original
NMN6191C
Noise-Cancelling Remote
Speaker Microphone is
the perfect choice when
you must be heard the
first time.
®
RLN4941A
RMN5038A
audio accessories
make it possible.
AARLN4885B
WADN4190B
4
MT 2000/MTS 2000
for tough conditions...
Remote Speaker Microphones (RSM)
These compact Remote Speaker Microphones are water-resistant and allow talking and listening
without removing the radio from the belt or case. They have a 6-foot coiled cord assembly, 3.5mm
earjack, swivel clip
The orange button on the microphone head can be used to signal that the operator needs help.
This microphone offers high/low volume control and has a
Emergency activation from the RSM is delayed until programmed Mandown Pre-alert and Postalert delays elapse. Depending on radio model, factory defaults or previous programming could set
the delay times for as long as 8 to 120 seconds.
RMN5038ARemote Speaker Microphone with Emergency Button
3.5mm earjack on the microphone head.
RSM Audio Accessories
The following earpieces are compatible with the Remote Speaker Microphone with Emergency
Button RMN5038A.
RLN4941AReceive-Only Earpiece with Translucent Tube and Rubber Eartip
AARLN4885BReceive-Only Covered Earbud
WADN4190BReceive-Only Flexible Earpiece
Public Safety Microphones (PSM)
Public Safety Speaker Microphones include straight cord assembly, 3.5mm earjack,
swivel clip, quick disconnect latch, antenna connector
toggle switch. Use with radio’s antenna, sold separately. RF adapter is included.
NMN6228C* Noise-cancelling Public Safety Microphone with 30 Inch Straight Cord
NMN6244B* Noise-cancelling Public Safety Microphone with 24 Inch Straight Cord
NMN6243B* Noise-cancelling Public Safety Microphone with 18 inch Straight Cord
and receive audio high/low
NMN6193C
RMN5038A
Mandown, Public Safety Tilt Switch
The Mandown, Public Safety Tilt Switch functions as an external emergency switch that is activated when the radio unit is tilted at an angle greater than 60 degrees. No other audio accessory can
be attached to the radio while the tilt switch is attached. Radio must be programmed to enable the
emergency tilt feature.
NTN7660C* Mandown, Public Safety Tilt Switch
Epaulet Straps
Black leather Epaulet Strap secures Remote Speaker Microphone to epaulet on shirt or jacket and
accommodates back clip in leather cut-outs. Snap closure secures cord to allow reliable communications in hostile environments.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, with Clip
RLN4294A
*Intrinsically Safe
RLN4295A
NTN7660C
5
NTN8371A
audio
Surveillance Kits
Surveillance accessories allow the radio user to privately receive messages with the earpiece and are ideal when environments require discreet communication. The following surveillance accessories require the 3.5mm threaded adapter jack
BDN6676D that attaches to the radio, unless being used with speaker microphone.
1-WIRE SURVEILLANCE KITS
BDN6664A* Receive
BDN6665A*
BDN6726A* Receive-Only Earpiece with Standard Earphone (1-Wire). Black
BDN6727A*
BDN6666A* Receive
BDN6728A* Receive-Only Earpiece with Volume Control and Earloop (1-Wire). Black.
BDN6667A* Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Beige.
BDN6669A*
BDN6729A* Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Black.
BDN6731A*
BDN6668A* Earpiece with Microphone and Push-to-Talk Separate (3-Wire). Beige.
BDN6670A*
BDN6730A Earpiece with Microphone and Push-to-Talk Separate (3-Wire). Black
BDN6732A
†
†
†
†
†
†
Surveillance Kits - With Extended-Wear Comfort Earpiece
These kits include an extended-wear comfort earpiece with rubber eartip and clear, comfortable acoustic tube. Users hear
transmissions clearly, while the clear tube provides a discreet appearance.
RLN5314A Comfort Earpiece, Receive-Only. Beige.
RLN5313A Comfort Earpiece, Receive-Only. Black.
RLN5311A Earpiece w/Microphone and PTT Combined (2-Wire). Beige.
RLN5312A Earpiece w/Microphone and PTT Combined (2-Wire). Black.
-Only Earpiece with Standard Earphone (1-Wire). Beige.
Extra Loud Receive-Only Earpiece with Standard Earphone (1-Wire). Beige.
Extra Loud Receive-Only Earpiece with Standard Earphone (1-Wire). Black
-Only Earpiece with Volume Control and Earloop (1-Wire). Beige.
2-WIRE SURVEILLANCE KITS
Extra Loud Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Beige.
Extra Loud Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Black.
3-WIRE SURVEILLANCE KITS
Extra Loud Earpiece with Microphone and Push-to-Talk Separate (3-Wire). Beige.
Extra Loud Earpiece with Microphone and Push-to-Talk Separate (3-Wire). Black
RLN5311A
NTN8370A
BDN6676D
6
Noise Kits
Extreme Noise Kits provide extra comfort and/or noise protection for users wearing surveillance accessories. Lightweight, translucent tube attaches to Motorola
surveillance accessories to provide flexibility and comfort. Clothing clip prevents
accessory from being pulled from the ear due to body movement or head rotation.
For optimal performance, Extra Loud Earphones are recommended for Noise Kits.
NTN8370A Extreme Noise Kit. Includes 2 foam earplugs. For high-noise
environments. Noise reduction = 24dB. Can be used with
Clear Comfortable Earpieces, sold separately.
NTN8371ALow Noise Kit - Clear Acoustic Tube Assembly. Includes
1 rubber eartip. For low-noise environments,
5080369E39
5080370E91
BDN6676D* 3.5mm Jack Adapter with Quick Disconnect Latch
5080384F72Replacement Foam Plugs. Pack of 50
5080370E97Replacement Standard Clear Rubber Eartips. Pack of 25.
†
†
does not provide hearing protection.
Extra Loud Earphone. Beige.
Extra Loud Earphone. Black.
SURVEILLANCE REPLACEMENT ACCESSORIES
For use with NTN8370A. Noise reduction = 24dB.
For use with NTN8371A
Clear Comfortable Earpieces
The Clear Comfortable Earpiece forms to the inside of the ear and is perfect for
low-noise environments. It’s made of easy-to-clean, chemically-inert hypo-allergenic material. Compatible with NTN8371A and all Surveillance Kits.
RLN4760ASmall Custom Earpiece - Right Ear
RLN4761AMedium Custom Earpiece - Right Ear
RLN4762ALarge Custom Earpiece - Right Ear
RLN4763ASmall Custom Earpiece - Left Ear
RLN4764AMedium Custom Earpiece - Left Ear
RLN4765ALarge Custom Earpiece - Left Ear
Enables users to communicate with ease, in full privacy, without visible equipment.
This miniaturized receiver is discreetly hidden in the ear, where it can be worn comfortably for long periods of time. Small as it is, it offers a full range of audio functions
including automatic squelch, automatic gain control and noise filtering. Average battery
life is approximately 100 hours and includes an end-of-life warning signal when the
battery needs to be changed. Kit includes wireless receiver, inductive neckloop, 6 spare
batteries and 5 spare earguards. For use with any standard 2 or 3-Wire Motorola
Surveillance Kit.
RLN4922ACompletely Discreet Earpiece Kit
RLN4919AReplacement Earguards. 5 per pack.
RNN4005AReplacement 1.4 Volt Batteries. 6 per pack.
Ear Microphone Systems (EMS)
This compact, lightweight unit picks up sound through bone vibrations in the ear canal. The miniature earpiece leaves the hands-free and face unobscured, good for rescue and emergency personnel that must retain the ability to help, hear and speak directly to others...those not on the communication system. EMS may be worn with protective masks without reduction in clarity of sound. It’s
ideal for high-noise environments. Available in PTT or Voice-Activated (VOX). Interface Module is
required and sold separately.
BDN6677A*EMS with PTT Interface. Black. For standard noise levels (up to 95dB).
BDN6678A*EMS with PTT Interface. Beige. For standard noise levels (up to 95dB).
BDN6641A*EMS with PTT Interface. Grey. For high noise levels (up to 105dB).
BDN6708B* Push-to-Talk Only Interface Module
BDN6671B* Push-to-Talk and Voice-Activated Interface Module
RLN4922A
The Completely Discreet Earpiece is easy
to use, just remove the earpiece from any
standard 2 or 3-Wire Surveillance Kit and
plug in the neckloop, which is easily hidden under clothing. Security personnel will be able to wear this tiny
receiver comfortably for hours at a time!
BDN6677A
EMS with
Push-to-Talk
Interface
Module.
OPTIONAL ACCESSORIES FOR THE EMS
0180300E25Earguard with Adjustable Loop
0180358B38*Remote Push-to-Talk Ring Switch
0180300E83*Remote Push-to-Talk Body Switch
0180358B32Earholder. Black, size small. Secures Ear Microphone in ear.
0180358B33Earholder. Black, size medium. Secures Ear Microphone in ear.
0180358B34Earholder. Black, size large. Secures Ear Microphone in ear.
0180358B35Earholder. Clear, size small. Secures Ear Microphone in ear.
0180358B36Earholder. Clear, size medium. Secures Ear Microphone in ear.
0180358B37Earholder. Clear, size large. Secures Ear Microphone in ear.
4280369E44Replacement Belt Clip with Screws
5080358B28Eartips. Black, size medium. Pack of 10.
5080358B29Eartips. Black, size large. Pack of 10.
5080358B30Eartips. Beige, size medium. Pack of 10.
5080358B31Eartips. Beige, size large. Pack of 10.
0180305J46 Training CD-ROM
For Ear Microphone System and Temple Transducer.
*Intrinsically Safe
0180300E83
EMS
with Body
Push-to-Talk
Switch.
0180300E25
7
When seconds count,
audio
Motorola Original
audio accessories
can help assure
critical information gets
communicated right the
first time —
quickly, clearly,
and accurately.
®
Security teams know
that for dependability
and all-day comfort, the
BDN6780A
Flexible Ear Receiver
BDN6717B goes to the
head of the class.
Flexible Ear Receiver
This receive-only earpiece contains a flexible earloop and speaker
which rests external to the ear. Black, without volume control.
It plugs directly into adapter BDN6676D or the earjack on speaker microphones.
BDN6719AFlexible Ear Receiver with 3.5mm Threaded Plug
Adapter BDN6676D required if not used with speaker microphones.
BDN6676D 3.5mm Jack Adapter with Quick Disconnect Latch
7580372E11 Replacement Foam Ear Cushion for BDN6717B.
Pellet-Style Earpieces
Pellet-style earpieces allow users to receive communication discreetly
and are comfortable for extended-wear use.
unless being used with a speaker or microphone.
BDN6676D 3.5mm Jack Adapter with Quick Disconnect Latch
7580372E70 Replacement Foam Cushion for Pellet Earpieces
BDN6780A
8
MT 2000/MTS 2000
public safety essentials...
The Temple
Transducer
RMN4049A
allows users to
receive audio
without covering
the ear.
Temple Transducer
The Temple Transducer represents a significant achievement in headset design and functionality. It
allows the user to receive audio without covering the ear. The receiver portion of this accessory
rests on the temples and is capable of converting the receive audio from a two-way radio into sound
vibration. The sound vibration is transmitted through the surrounding human tissue and bone directly
into the inner ear where it is received by the user. It features an
boom microphone.The Temple Transducer enhances communication and safety by not impairing the
user’s hearing of the external sound environment, such as machinery and equipment, warning and
fire alarms, the intercom, traffic and even casual conversations with co-workers.
In-line PTT and noise-cancelling
RMN4049A
RMN5049A
RMN4049A* Temple Transducer
0180305J46 Training CD-ROM. For Ear Microphone System and Temple Transducer.
Rugged Temple Transducer
The Rugged Temple Transducer comes equipped with all the features of the basic model. It sports a
bigger Push-to-Talk button and a larger noise-cancelling boom microphone. It is fully adjustable for
different head sizes, making it comfortable for extended-wear. Over-the-head band allows users to
wear helmets, hardhats and other head gear – and it really stays in place! Water-resistant boom
microphone is ideal for use in blowing rain and the secure cap on PTT prevents accidental activation
in mission critical situations.
RMN5049A*Rugged Temple Transducer
*Intrinsically Safe
9
audio
The same winning quality
and dependability you see
at professional football
stadiums and motor
speedways can be yours
with Motorola Original
accessories.
The Racing Headset
RMN5015A lets
users take charge...
in spite of high
background noise.
®
Racing Headset
This heavy-duty headset can be worn with most hard hats. Ideal for high-noise environments; racing teams like CART
Adapter Cable required.
Receive-Only Headsets are the right choice for high-noise environments where users
must hear information clearly, but seldom need to transmit. Dual-Muff headsets feature easily replaceable earseals filled with a liquid and foam combination to provide
excellent protection from outside noise as well as comfort. These are for use with
Remote and Public Safety Speaker Microphones with a 3.5mm threaded jack. They
can also be plugged directly into the radio when used with BDN6676D.
RMN4056B Receive-Only Dual-Muff Headband Style Headset. For use with
with 3.5mm threaded jack. Can be plugged directly into radio
with 3.5mm adapter BDN6676D. Noise reduction = 24dB.
RMN4057B Receive-Only, Dual-Muff, Hardhat Headset. Mounts easily to
hardhats with slots. For use with remote and public safety
microphones with 3.5mm threaded jack. Can be plugged
directly into radio with 3.5mm adapter BDN6676D.
BDN6676D 3.5mm Jack Adapter with Quick Disconnect Latch
Lightweight Headsets
Lightweight headsets provide high-clarity, hands-free, discreet two-way communication,
while maintaining the comfort necessary for extended-wear in moderate noise environments. Audio adapter BDN6676D required.
RMN4056B
10
NMN6245A Single-Muff Lightweight Headset with In-Line PTT Switch
Requires audio adapter BDN6676D.
NMN6246B Ultra-Light Headset with Boom Microphone, In-Line PTT Switch
Earbud style receiver. Requires audio adapter BDN6676D.
NMN1020A Lightweight Headset with Boom Microphone. Can be worn with
helmet or safety glasses. Includes adapter cable NKN6498A.
Requires audio adapter BDN6676D.
NKN6498A Headset Adapter Cable for use with NMN1020A
BDN6676D 3.5mm Jack Adapter with Quick Disconnect Latch
MT 2000/MTS 2000
clearly understood...
Noise-Cancelling Headsets with Boom Microphone
Ideal for two-way communication in extremely noise environments. Dual-Muff, tactical headsets
include 2 microphones on outside of earcups which reproduce ambient sound back into headset.
Harmful sounds are suppressed to safe levels and low sounds are amplified up to 5 times original
level, but never more than 82dB. Has on/off volume control on earcups. Easily replaceable ear seals
are filled with a liquid and foam combination to provide excellent sealing and comfort. 3-foot coiled
cord assembly included. Adapter Cable RKN4095A required. Hardhat not included.
RLN4923BReplacement Earseals for RMN4051B/RMN4052A/RMN4053A
Includes 2 snap-in earseals.
Hardhat Mount Headset With
Noise-Cancelling Boom Microphone
Ideal for two-way communication in high-noise environments, this headset mounts easily to hardhats with slots, or can be worn alone. Easily replaceable ear seals are filled with a liquid and foam
combination to provide excellent sealing and comfort. 3-foot coiled cord assembly included. Noise
reduction of 22dB. Intrinsically Safe (FM). Separate In-line PTT Adapter Cable RKN4095A required.
Hardhat not included. Black.
RMN4051BTwo-way, Hardhat Mount Headset with Noise-Cancelling Boom Microphone
RKN4095A In-line PTT Adapter Cable. For use with RMN4051B/RMN4052A/RMN4053A.
RMN4053A
RMN4051B
Medium Weight Headsets
Medium weight headsets offer high-clarity sound, with
the additional hearing protection necessary to provide
consistent, clear, two-way radio communication in
harsh, noisy environments or situations.
NMN6258A* Medium Weight, Dual-Muff,
Over-the-Head Style Headset with
In-line PTT
Noise reduction rating = 24dB.
NMN6259A*Medium Weight, Dual-Muff,
Behind-the-Head Style Headset
Can be worn with hardhat.
Noise reduction rating = 24dB.
NMN6258A
Heavy-Duty Headsets
Heavy-duty headsets include noise-cancelling boom
microphones and can be worn with or without a hardhat.
The Push-to-Talk switch is located on the earcup. On
voice-activated models, the VOX module is contained
within the headset. Headsets are for use in noise levels up to 125dB. Heavy-duty headsets require
radio adapter cable BDN6673B, sold separately.
BDN6645A Push-to-Talk Headset with Boom Microphone
A variety of carrying accessories are available for comfort and convenience. The carrying cases are available in sizes designed to fit radios with a battery and permit audio to
be heard clearly. Motorola carry cases were developed to meet the demands of public
safety and other users who operate in the most rigorous of environments.
Leather cases are constructed of top grain, 8 ounce leather and all stainless steel hardware. High-activity cases have a swivel D-ring button and belt loop. To remove
case from belt loop, rotate case 180 degrees and slide case upward, out of the holder.
Case stays on belt more securely in high
to swing freely with body movements.
STANDARD BELT LOOP CASES
NTN7238A Leather Case with Belt Loop, D-rings and T-strap
For use with high-capacity battery.
NTN7239ALeather Case with Belt Loop, D-rings and T-strap
For use with ultra-high capacity battery.
NDN4018B Leather DTMF Case with Belt Loop, D-rings and Antenna Strap
For use with high and ultra-high capacity batteries.
NTN7247A Nylon Case with Belt Loop and Strap
For use with high and ultra-high capacity batteries.
HIGH-ACTIVITY SWIVEL CASES
NTN8035B Leather Case with 2.5 Inch High-Activity Swivel Belt Loop,
D-rings and T-strap. For use with high-capacity battery.
NTN8037BLeather Case with 3 Inch High-Activity Swivel Belt Loop,
D-rings and T-strap. For use with high-capacity battery.
NTN8036BLeather Case with 2.5 Inch High-Activity Swivel Belt Loop,
®
NTN8038B Leather Case with 3 Inch High-Activity Swivel Belt Loop,
NDN4017BLeather DTMF Case with 3 Inch High-Activity Swivel Belt Loop,
D-rings and T-strap. For use with ultra-high capacity battery.
D-rings and T-strap. For use with ultra-high capacity battery.
D-rings and T-strap. For use with high and ultra-high capacity battery.
-activity applications while allowing the radio
NTN7247A
NTN8038B
NTN8036B
NTN8039B
NTN8040B
Carrying Accessories
T-STRAPS
NTN7782A T-Strap for Leather Carry Cases
NTN7376A T-Strap for Nylon Carry Cases
HIGH-ACTIVITY BELT LOOPS
NTN8039B 2.5 Inch High-Activity Swivel Belt Loop
NTN8040B 3 Inch High-Activity Swivel Belt Loop
HIGH-ACTIVITY BUTTONS
NTN1534A High-Activity D-Button with 2.5 Inch High-Activity Swivel Belt
Loop. For use with NTN8039B.
NTN1535A High-Activity D-Button with 3 Inch High-Activity Swivel Belt Loop
For use with NTN8040B.
NTN8063A High-Activity D-Button
BELT CLIPS
4205638V09 2.5 Inch Belt Clip, Black
4205638V07 3 Inch Belt Clip, Black Aluminum
BELT
4200865599 1.75 Inch Wide Black Belt
CARRYING STRAP
NTN5243A Adjustable, Black Nylon Carrying Strap
Attaches to D-ring on case.
D ATTACHMENT
NTN7484A D Attachment
NTN5243A
4200865599
12
MT 2000/MTS 2000
Universal
Chest Pack
HLN6602A
has adjustable
shoulder
and waist straps.
Chest Pack
Motorola Original®Universal Chest Pack protects the radio and provides the freedom from
holding it during standby communication mode. Universal Chest Pack fits virtually any radio.
HLN6602AUniversal Chest Pack with Radio Holder,
Pen Holder and Velcro Secured Pouch
1505596Z02Replacement Strap for HLN6602A/RLN4570A
Break-A-Way Chest Pack
All the features of the original Universal Chest Pack (HLN6602A) plus break-a-way tabs that
allow the entire pack to be pulled off with approximately 10 lbs. of pressure.
RLN4570ABreak-a-Way Chest Pack with Radio Holder,
Pen Holder and Velcro Secured Pouch.
1505596Z02Replacement Strap for HLN6602A/RLN4570A
RLN4570A
RLN4815A
Universal RadioPAk
The RadioPAk is lightweight and comfortable. Worn around the
waist, it keeps radios/phones at hand. It features a separate 6 x 8
inch zippered pouch for other on-the-job necessities. Adjustable
woven nylon belt fits both men and women.
RLN4815ARadioPAk Radio/Utility Case
4280384F89RadioPAk Extension Belt
TM
For waists larger than 40 inches.
Waterproof Bag
HLN9985BWaterproof Bag with Large Strap
Portable Radio Hangers
Portable Radio Hangers slide over and hang from the vehicle door panel, allowing
convenient, easy mounting. Radio belt clip required.
TDN9327APortable Radio Hanger for door panels up to 2.75 Inches.
TDN9373APortable Radio Hanger for door panels 2.75 to 3.25 Inches.
TDN9327A, TDN9373A
Unlike rigid holders, the universal-fit
RadioPAk is lightweight and comfortable. An ideal companion for two-way
radios, as well as iDEN
cellular phones.
®
portables and
13
Battery Characteristics
NiCd batteries provide the
maximum number of
batteries and chargers
charge/discharge cycles
and are best suited for
temperature extremes.
NiMH batteries
provide more
talk-time per shift
and are less prone
to memory effect.
Li-ion batteries
offer the best
Batteries
PREMIUM NICKEL CADMIUM - NiCd
NTN7143CR NiCd, 1200 mAh 7.5 Volt
NTN7372AR NiCd, 1200 mAh 7.5 Volt. Intrinsically Safe.
NTN7147AR NiCd, 1300 mAh 7.5 Volt. Intrinsically Safe.
NTN7149BR NiCd, 1300 mAh 7.5 Volt. CSA.
NTN7150AR NiCd, 1200 mAh 7.5 Volt. MSHA.
NTN7341AR NiCd, 1400 mAh 7.5 Volt. Intrinsically Safe.
NTN7144CR NiCd, 1500 mAh 7.5 Volt
NTN7143CR
NTN7144CR
WPNN4013A
power-to-weight ratio
of all chemistries,
with no memory effect.
14
PREMIUM NICKEL METAL HYDRIDE - NiMH
WPNN4013A NiMH, 2000 mAh 7.5 Volt
WPNN4037A NiMH, 1900 mAh 7.5 Volt
Intrinsically Safe.
IMPRES™ NiCd Batteries
IMPRES batteries, when used with an IMPRES charger, provide automatic,
adaptive reconditioning, end
Data is stored in the battery and communicated to the charger via a unique
IMPRES communication protocol which is designed to maximize talk-time
and optimize battery cycle life – all automatically.
HNN9028AR NiCd, 1500 mAh 7.5 Volt
HNN9029AR NiCd, 1500 mAh 7.5 Volt. Intrinsically Safe.
-of-life display and other advanced features.
NTN7372AR
MT 2000/MTS 2000
essential power...
Single-Unit, Compact, Rapid-Rate Chargers
These Chargers have the power supply built into the line cord giving the user a smaller base
unit for easier storage. Utilizing an enhanced charging algorithm that will help maximize the
life of batteries
RPX4747A Compact Rapid-Rate Charger, 110 Volt, US Plug
RPX4748A Compact Rapid-Rate Charger, 220 Volt, Euro Plug
RPX4749BCompact Rapid-Rate Charger, 230 Volt, UK Plug
Motorola Conditioning Charger (MCC)
The MCC features Instant Fault Detection technology that detects faulty batteries in seconds. You'll
know right away when a battery won't operate at peak performance - saving you time and trouble.
Each unit rapidly charges NiCd and NiMH batteries
negative pulse charging process minimizes overheating and overcharging, extending useful battery
life. Batteries can be left in the charger for extended periods of time, without worry of heat build-up.
Optional accessories are available that allow the MCC to be used in both AC and DC environments that’s flexibility.
and they can rapid-rate charge both NiCd and NiMH batteries.
and optimizes battery performance. It’s patented
WPPN4065BR
WPLN4090BR Charger Kit, 110 Volt AC. Includes single-unit base and 7 Volt adapter plate.
WPLN4091BR Charger Kit, 220 Volt AC. Includes single-unit base and 7 Volt adapter plate.
WPPN4002BR 110 Volt AC Single-Unit Base Charger Only
Adapter plates sold separately.
WPPN4006AR 220 Volt AC Single-Unit Base Charger Only
Adapter plates sold separately.
WPPN4004BR 7 Volt Adapter Plate
WPPN4065BRMulti-Unit Conditioning Charger, 4-Station Base, 110 Volt.
Adapter plates sold separately.
Vehicular Mounting
RLN4814AVehicular Mounting Bracket and Hard Wire
Cable for Single-Unit Motorola Conditioning Chargers
Includes DC Hard Wire Cable 3080384M21.
3080384M21 DC Hard Wire Cable with 3 AH
In-line fuse.
WPPN4002BR
Single-Unit Base Charger and
power supply shown with
optional Vehicular Power
Adapter 3080384G15.
Vehicular Power Adapter
3080384G15DC Vehicular Power Adapter
RLN4814A
15
WPLN4111AR
chargers
IMPRES™ Smart Energy Systems
Through the use of its advanced charging algorithm and automatic reconditioning features,
the IMPRES Smart Energy System ensures maximum talk-time and optimized battery cycle
life. This smart energy system automatically reconditions IMPRES batteries based on actual
usage, keeping them in peak condition. Talk-time and cycle life are optimized and the need
for manual maintenance programs is eliminated. Its advanced conditioning features allow
batteries to be safely left on the charger for extended periods of time without incurring the
damaging heat build-up which can decrease battery cycle life. In addition, batteries left in
the charger are kept fully charged so they are always ready when needed. This rapid-rate,
tri-chemistry charging system will also charge compatible non-IMPRES batteries and supports multiple radio platforms including SABER, XTS and HT 1000 Series portables.
WPLN4130A
Display Readout
WPLN4111AR
IMPRES™ Single-Unit Chargers
WPLN4111AR IMPRES Single-Unit Charger, 110 Volt, US Plug
WPLN4112AR IMPRES Single-Unit Charger, 220 Volt, Euro Plug
WPLN4113AR IMPRES Single-Unit Charger, 240 Volt, UK Plug
5889254E01 Battery Adapter. Required for NTN4538DR,
NTN4593DR, NTN7014BR and NTN8818A batteries.
IMPRES™ Multi-Unit Chargers
WPLN4108BR IMPRES Multi-Unit Charger, 110 Volt, US Plug
WPLN4109BR IMPRES Multi-Unit Charger, 220 Volt, Euro Plug
WPLN4110BR IMPRES Multi-Unit Charger, 240 Volt, UK Plug
4385922B01 Battery Adapter. Required for NTN4538DR,
NTN4593DR, NTN7014BR and NTN8818A batteries.
NLN7967A Wall Mount for Multi-Unit Chargers
IMPRES™ Multi-Unit Chargers with Display Modules
Charger Display Modules provide powerful, “real time” analyzing information for IMPRES
batteries, including current charge status, battery mAh, percent rated capacity and battery
voltage. Readout displays battery kit number, serial number and chemistry and the time
remaining to complete the charge for NiCd and NiMH batteries. It also forecasts the number
of cycles to next reconditioning and more.
WPLN4130A IMPRES Multi-Unit Charger with Display Modules, 110 Volt, US Plug
WPLN4131A IMPRES Multi-Unit Charger with Display Modules, 220 Volt, Euro Plug
WPLN4132A IMPRES Multi-Unit Charger with Display Modules, 240 Volt, UK Plug
4385922B01 Battery Adapter. Required for NTN4538DR,
NTN4593DR, NTN7014BR and NTN8818A batteries.
NLN7967A Wall Mount for Multi-Unit Charger
16
IMPRES™ Individual Charger Display Module
This module is compatible with the standard IMPRES™ Multi-Unit Charger WPLN4108BR,
WPLN4109BR and WPLN4110BR. Up to 6 modules can be used per charger, one for each
charging pocket. Includes detailed installation instructions.
RLN5382A Charger Display Module for IMPRES Multi-Unit Charger
Version 1.3 or Later.
Note: Display Modules compatible with Multi-Unit Charger version 1.2 or earlier require a
software flash update.
Version number is located on label on the bottom of the IMPRES™ Multi-Unit charger. If no
version is shown, it is earlier than version 1.2. Version 1.2 will appear as V1.20, 1.3 will
appear as V1.30, etc.
RLN5382A
IMPRES™ CD
This CD provides an interactive guide to the IMPRES Charging System. It outlines the benefits and gives examples of application usage.
0180305J70 IMPRES CD
MT 2000/MTS 2000
essential power...
WPLN4079BR
Battery Maintenance System
Increase the useful life of your batteries. Using interchangeable battery
adapters (sold separately), the BMS
analyzing, conditioning and cycle testing batteries. It supports NiCd, NiMH
and Li-ion battery chemistries (Li-ion 6-station units only) and tracks better
voltage and capacity (mAh). Its easy-to-use design supports hundreds of
two-way, cellular and camcorder batteries. The BMS
warranty and includes serial printer* port (RS-232).
*Compatible with the STAR Micronics SP200 series printers and other printers
with STAR printer emulation. STAR Micronics printers are available through
STAR Micronics distributors.
PLUS
Upgrades WPLN4079AR, WPLN4080AR, WPLN4081AR.
Allows units to support Li-ion batteries.
Does not support Li-ion or 3-cell batteries.
Does not support Li-ion or 3-cell batteries.
Battery Maintenance System
TDN9435CAdapter. Compatible with NiCd batteries only.
CDN6364A Adapter. Compatible with both NiCd and NiMH batteries.
PLUS
, 110 Volt AC, 50/60 Hz, US Plug
PLUS
, 230 Volt AC, 50/60 Hz, Euro Plug
PLUS
, 230 Volt AC, 50/60 Hz, UK Plug
Li-ion Field Upgrade Kit
PLUS
, 110 Volt AC, 50/60 Hz
PLUS
(BMS
PLUS
) Adapters
Battery Optimizing System II (BOS II)
No other battery analyzer matches the speed, accuracy, versatility and ease-of-use of the BOS II in providing
powerful analyzing capabilities. Users can select from 12 pre-programmed service programs making it quick
and easy to get up and running. Because the BOS II is programmable, users can create custom programs to
perform a wide variety of tasks specific to individual needs. New enhancements include new navigation keys
and an improved, more intuitive menu system. Regular use of the BOS II can optimize battery performance
and help extend battery life, helping reduce battery replacement costs.
NDN4005B
WPLN4124AR
WPLN4124AR BOS II, 4-Station, 90-264 Volt AC, US Plug. Adapter Plates Required.
WPLN4125AR BOS II, 4-Station, 90-264 Volt AC, Euro/UK Plug. Adapter Plates Required.
RL72403BOS II Battery Adapter.
• Quicktest™ diagnostic feature measures a battery’s state of health in approximately 2 to 5 minutes
• Supports NiCd, NiMH, Li-ion and SLA batteries
• Increased power-programmable from 100 mAh to 4 Amps per station
• Programmable adapters allow customization of maintenance routines
• Proprietary reduction cycle restores NiCd and NiMH batteries
• Printer output for reports and labels with computer interface
(Includes both 9-pin serial and 25-pin parallel ports)
• 100-Watt Universal Power Supply (110-240 VAC) provides up to 4 amps of power per station
• Interchangeable adapter plates accommodate nearly all Motorola two-way batteries
and other major brands
17
Those on the road love
the convenience of a
Vehicular Travel Charger.
And no wonder, it helps
assure that your radios
are always good to go
when you are –
chargers and antennas
and there’s no need
to hunt for an extra
battery when you need
to hit the road.
Vehicular Travel Charger
A great traveling companion that ensures constant communication while on the road. Its small compact design allows the radio to be used while rapid charging in the charger base. Unit includes a
voltage regulated vehicular charger adapter, custom charger base, mounting bracket
RLN4884BVehicular Travel Charger
RLN5914AUniversal Mounting Bracket for RLN4884B.
Includes screws and nylon strap cord.
TRAVEL CHARGER TRANSFORMERS
2580600E05Transformer, US, 120 Volt
2580600E06Transformer, European, 230 Volt
2580600E07Transformer, UK, 230 Volt
2580600E08Transformer, Argentina, 220 Volt
and coil cord.
RLN4884B
Vehicular Charger
This 12 Volt DC charger is ideal for mobile use. It charges portable radio NiCd
batteries in rapid-rate charge mode (less than 3 hours) until full charge is obtained
and then switches to trickle charge mode. A micro-processor controls the charge
rate. This durable unit comes with a metal mounting bracket and is
PAC_RT compatible.
18
TDN9816A Vehicular Charger
TDN9816A
MT 2000/MTS 2000
tested and tuned for performance...
Flexible Whip
Flexible whip antennas have a one-piece finish and steel core for optimal radiation characteristics. They provide more comfort when the radio is worn on a belt.
8505241U05 6 Inch Flexible Whip Antenna, 403-520 MHz
8505241U03 7 Inch Flexible Whip Antenna, 806-869 MHz
8505241U047 Inch Flexible Whip Antenna, 764-870 MHz
Helical
Helical antennas are sturdy and dependable for years of failsafe communication.
Each antenna is designed and built to quality standards. The skirt at the base of
the connector helps to seal out damaging elements. The connector is made of
plated brass material for long life.
8505644V01 6 Inch Helical Antenna, 136-151 MHz
8505644V02 6 Inch Helical Antenna, 151-162 MHz
8505644V03 6 Inch Helical Antenna, 162-174 MHz
8505644V04 3 Inch Helical Antenna, 403-435 MHz
8505644V05 3 Inch Helical Antenna, 435-470 MHz
8505644V06 3 Inch Helical Antenna, 470-520 MHz
8505241U05
8505644V01
8505644V03
8505644V04
Dipole
Dipole-molded Antennas are injection molded in lasting polyurethane.
The wide skirt at the bottom of the connector protects against damaging
environmental elements. The Dipole Antenna is ideal when strong and
solid signal clarity is demanded.
NAF4000B 8 Inch Dipole, 806-869 MHz
8505884R02 8 Inch Dipole, 896-941 MHz
Wideband
Wideband antennas are ideal when radios are used in different frequencies since
one antenna will cover all ranges.
8505518V01 8 Inch Wideband Antenna, 136-174 MHz
Stubby
This quarterwave stubby antenna is ideal when the radio is worn on a belt
because the short antenna is non-obtrusive. This is a broad band antenna that
can be used for both 800 MHz and 900 MHz applications.
RAD4194A 3.55 Inch Stubby Antenna, 150-162 MHz
8505241U06 4 Inch Stubby Antenna, 806-941 MHz
NAF4000B
8505884R02
8505241U06
19
Police
Whether in hot pursuit or investi-
gating a cold case, communica-
tion can be made much easier
with a CommPort™ Integrated
Microphone/Receiver System.
Fire
It takes two hands for climbing
ladders and controlling hoses, and
solutions like our Chest Pack pro-
LTS 2000 portable
vide both welcome freedom and
valued protection in the heat of
the action.
Emergency Response
First responders deserve first-
class tools for communicating
their position and conditions, and
our Lightweight Headsets help
everyone quickly and clearly get
the message.
Security
From crowd control to answering
an alarm signaling illegal entry, a
Remote Speaker Microphone lets
professionals respond instantly
without the need to reach
for the radio controls.
20
LTS 2000
90 modes,10 channels...
LTS 2000TManalog radios blend simple operation and key
operating features into a compact, lightweight design.
TM
Powerful yet easy to use, LTS 2000
radios offer dual-mode opera-
“This is Officer
Swanson...
I need a tow truck
at 1475 West Elm
for abandoned
vehicle towing.”
tion that allows for communication on both conventional channels
and private trunked channels — 90 modes in all. And the full APCO
16 feature set is included.
21
In the case.
microphones and audio
HMN9030A
Out of the case.
In. Out.
It’s more efficient
to leave a radio
in place and wear a
microphone on a uniform
jacket or shirt collar —
and Motorola Original
audio accessories
Remote Speaker
Microphone is the
dependable choice
when you must
be heard the first time.
®
make it possible.
22
LTS 2000
essential communication...
Remote Speaker Microphone (RSM)
This compact, water-resistant unit allows radio users to talk and listen without removing the radio
from the belt or case. Attaches securely onto shirt or collar with a swivel clip on the back of the
unit. Includes 6-foot coiled cord and Push-to-Talk switch. Ideal for public safety personnel, or anyone who wears work gloves or uniforms. Intrinsically Safe (FM).
HMN9030A*Remote Speaker Microphone
HKN9094A*Replacement Coiled Cord for HMN9030A
Epaulet Strap
Black leather Epaulet Strap secures Remote Speaker Microphone to
epaulet on shirt or jacket and accommodates back clip in leather cut-outs. Snap closure secures
cord to allow reliable communications in hostile environments.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, with Clip
Surveillance Kits
Surveillance accessories allow the radio user to privately receive messages with
the earpiece. They are ideal when environments require discreet communication.
1-WIRE SURVEILLANCE KIT
HMN9727B*Receive-Only Earpiece with Standard Earphone (1-Wire). Beige.
RLN4894AReceive-Only Earpiece with Standard Earphone (1-Wire). Black.
HMN9752B*Receive-Only Earpiece with Volume Control (1-Wire). Beige.
2-WIRE SURVEILLANCE KITS
HMN9754D*Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Beige.
RLN4895AEarpiece with Microphone and Push-to-Talk Combined (2-Wire). Black.
Surveillance Kits - With Extended-Wear Comfort Earpiece
These kits include an extended-wear comfort earpiece with rubber eartip and clear, comfortable
acoustic tube. Users hear transmissions clearly, while the clear tube provides a discreet appearance.
RLN5317A Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Beige
RLN5318A Earpiece with Microphone and Push-to-Talk Combined (2-Wire). Black
*Intrinsically Safe (FM)
23
audio
Noise Kits
Extreme Noise Kits provide extra comfort and/or noise protection for users wearing surveillance accessories. Lightweight, translucent tube attaches to Motorola
surveillance accessories to provide flexibility and comfort. Clothing clip prevents
accessory from being pulled from the ear due to body movement or head rotation.
For optimal performance, Extra Loud Earphones and Clear Comfortable Earpieces,
both sold separately, are recommended for Noise Kits.
NTN8370A Extreme Noise Kit. Includes 2 foam earplugs.
For high-noise environments. Noise reduction = 24dB.
Includes 1 rubber eartip. For low noise environments,
5080369E39
5080370E91
5080384F72Replacement Foam Plugs. Pack of 50
5080371E73Replacement Foam Plugs. Pack of 25
5080370E97Replacement Standard Black Rubber Eartips. Pack of 25.
†
†
does not provide hearing protection.
Extra Loud Earphone. Beige.
Extra Loud Earphone. Black.
SURVEILLANCE REPLACEMENT ACCESSORIES
For use with NTN8370A. Noise reduction rating = 24dB.
For use with NTN8371A.
For use with NTN8371A.
Clear Comfortable Earpieces
The Clear Comfortable Earpiece forms to the inside of the ear and is perfect for
low noise environments. It’s made of easy-to-clean, chemically-inert hypo-allergenic material. Compatible with NTN8371A and all Surveillance Kits.
NTN8371A
NTN8370A
BDN6720A
RLN4760ASmall Custom Earpiece - Right Ear
RLN4761AMedium Custom Earpiece - Right Ear
RLN4762ALarge Custom Earpiece - Right Ear
RLN4763ASmall Custom Earpiece - Left Ear
RLN4764AMedium Custom Earpiece - Left Ear
RLN4765ALarge Custom Earpiece - Left Ear
Flexible Ear Receiver
This black, receive-only earpiece contains a flexible earloop and speaker
which rests external to the ear.
Lightweight headsets provide high-clarity, discreet two-way
communication, while maintaining the comfort necessary for
extended-wear in moderate noise environments. Adjusts for
left or right ear operation. No adapter required.
RMN4016A* Single-Muff, Adjustable, Lightweight Headset with Boom
Microphone and In-line PTT
REX4648A Replacement Foam Earpad and Windscreen for RMN4016A
Enables users to communicate with ease, in full privacy, without visible equipment. This
miniaturized receiver is discreetly hidden in the ear, where it can be worn comfortably
for long periods of time. Small as it is, it offers a full range of audio functions including
automatic squelch, automatic gain control and noise filtering. Average battery life is
approximately 100 hours and includes an end-of-life warning signal when the battery
needs to be changed. Kit includes wireless receiver, inductive neckloop, 6 spare batteries and 5 spare earguards. For use with any standard 2 or 3-Wire Motorola Surveillance
Kit.
RLN4922ACompletely Discreet Earpiece Kit
RLN4919AReplacement Earguards. 5 per pack.
RNN4005AReplacement 1.4 Volt Batteries. 6 per pack.
Ear Microphone Systems (EMS)
This compact, lightweight unit picks up sound through bone vibrations in the ear canal. The miniature earpiece leaves the hands-free and face unobscured, good for rescue and emergency personnel that must retain the ability to help, hear and speak directly to others...those not on the communication system. EMS may be worn with protective masks without reduction in clarity of
sound. It’s ideal for high-noise environments. Available in PTT or Voice-Activated (VOX). Interface
Module is required and sold separately.
BDN6646C*EMS with PTT Interface. For standard noise levels (up to 95dB).
BDN6706B* EMS with Voice-Activated and PTT Interface
For standard noise levels (up to 95dB).
OPTIONAL ACCESSORIES FOR THE EMS
0180300E25Earguard with Adjustable Loop
0180358B38*Remote Push-to-Talk Ring Switch
0180300E83*Remote Push-to-Talk Body Switch
0180358B32Earholder. Black, size small. Secures Ear Microphone in ear.
0180358B33Earholder. Black, size medium. Secures Ear Microphone in ear.
0180358B34Earholder. Black, size large. Secures Ear Microphone in ear.
0180358B35Earholder. Clear, size small. Secures Ear Microphone in ear.
0180358B36Earholder. Clear, size medium. Secures Ear Microphone in ear.
0180358B37Earholder. Clear, size large. Secures Ear Microphone in ear.
4280369E44Replacement Belt Clip with Screws
5080358B28Eartips. Black, size medium. Pack of 10.
5080358B29Eartips. Black, size large. Pack of 10.
5080358B30Eartips. Beige, size medium. Pack of 10.
5080358B31Eartips. Beige, size large. Pack of 10.
0180305J46 Training CD-ROM
For Ear Microphone System and Temple Transducer.
0180300E83
EMS
with Body
Push-to-Talk
Switch.
RLN4922A
The Completely Discreet Earpiece is easy
to use, just remove the earpiece from any
standard 2 or 3-Wire Surveillance Kit and
plug in the neckloop, which is easily hidden under clothing. Security personnel will be able to wear this tiny
receiver comfortably for hours at a time!
BDN6646C
EMS with
Push-to-Talk
Interface
Module.
0180300E25
*Intrinsically Safe
25
carrying accessories
You’d be surprised how
much time can be saved
in emergencies when
each user’s radio is
always in the same
place — made
easy by this versatile
case selection of
Motorola Original
carry accessories
Leather and Nylon Carrying Cases
A variety of carrying accessories are available for comfort and convenience. The carrying cases are available in sizes designed to fit radios with a battery and permit audio to
be heard clearly. Motorola carry cases were developed to meet the demands of public
safety and other users who operate in the most rigorous of environments.
Leather cases are constructed of top grain, 8 ounce leather and all stainless steel hardware. High-activity cases have a swivel D-ring button and belt loop. To remove
case from belt loop, rotate case 180 degrees and slide case upward, out of the holder.
Case stays on belt more securely in high-activity applications while allowing the radio
to swing freely with body movements.
STANDARD BELT LOOP CASES
HLN9428ALeather DTMF Case with Belt Loop and-D-rings
For use with standard capacity battery.
HLN9429ALeather DTMF Case with Belt Loop and D-rings
For use with FM approved 1100 mAh battery.
HLN9431A Leather DTMF Case with Belt Loop and D-rings
For use with FM approved 600 mAh slim battery.
HIGH-ACTIVITY SWIVEL CASES
HLN9421A Leather DTMF Case with High-Activity Swivel Belt Loop
For use with standard battery.
HLN9426A Leather DTMF Case with High-Activity Swivel Belt Loop
For use with FM approved 1100 mAh battery.
HLN9427A Leather DTMF Case with High-Activity Swivel Belt Loop
For use with FM approved 600 mAh battery.
®
Carrying Accessories
HIGH-ACTIVITY BELT LOOPS
NTN8039B 2.5 Inch High-Activity Swivel Belt Loop
NTN8040B 3 Inch High-Activity Swivel Belt Loop
HLN9428A
HLN9421A
NTN5243A
BELT CLIPS
HLN9724A 2.5 Inch Belt Clip
HLN8255B 3 Inch Spring Action Belt Clip
CARRYING STRAP
NTN5243A Adjustable, Black Nylon Shoulder Strap
Attaches to D-ring on case.
SWIVELLER
TDN1002A Swiveller. Includes holster belt and strap.
Motorola Original®Universal Chest Pack protects the radio and provides the freedom from
holding it during standby communication mode. Universal Chest Pack fits virtually any radio.
HLN6602AUniversal Chest Pack with Radio Holder,
Pen Holder and Velcro Secured Pouch
1505596Z02Replacement Strap for HLN6602A/RLN4570A
Break-A-Way Chest Pack
All the features of the original Universal Chest Pack (HLN6602A) plus
break-a-way tabs that allow the entire pack to be pulled off with
approximately 10 lbs. of pressure.
RLN4570A
RLN4815A
RLN4570ABreak-a-Way Chest Pack with Radio Holder,
Pen Holder and Velcro Secured Pouch.
1505596Z02Replacement Strap for HLN6602A/RLN4570A
Universal RadioPAk
The RadioPAk is lightweight and comfortable. Worn around the waist,
it keeps radios/phones at hand. It features a separate 6 x 8 inch zippered pouch for other on-the-job necessities. Adjustable woven nylon
belt fits both men and women.
RLN4815ARadioPAk Radio/Utility Case
4280384F89RadioPAk Extension Belt
TM
For waists larger than 40 inches.
Waterproof Bag
HLN9985BWaterproof Bag with Large Strap
Portable Radio Hangers
Portable Radio Hangers slide over and hangs from the vehicle door panel, allowing convenient, easy mounting. Radio belt clip required.
TDN9327APortable Radio Hanger for door panels up to 2.75 inches.
TDN9373APortable Radio Hanger for door panels 2.75 to 3.25 inches.
Unlike rigid holders, the universal-fit
RadioPAk is lightweight and comfortable. An ideal companion for two-way
radios, as well as iDEN
cellular phones.
TDN9327A, TDN9373A
®
portables and
27
Battery Characteristics
NiCd batteries provide the
maximum number of
charge/discharge cycles
and are best suited for
temperature extremes.
batteries and chargers
HNN9808B
NiMH batteries
provide more
talk-time per shift
and are less prone
to memory effect.
Li-ion batteries
offer the best
power-to-weight ratio
of all chemistries,
with no memory effect.
Batteries
Motorola Original®Batteries are ruggedly designed for lasting durability and
system tested with Motorola two-way radios to ensure optimum performance.
PREMIUM NICKEL CADMIUM - NiCd
HNN9808B NiCd, 600 mAh 7.5 Volt. Intrinsically Safe, Slim.
HNN9628B NiCd, 1200 mAh 7.5 Volt
HNN9701A NiCd, 1100 mAh 7.5 Volt. Intrinsically Safe.
Single-Unit, Rapid-Rate Chargers
The Single-Unit Intellicharger utilizes an enhanced charging algorithm that
helps maximize the life of batteries. It can rapid-rate charge both NiCd and
NiMH batteries in approximately one hour.
HTN9042A Rapid-Rate Intellicharger, 120 Volt, US Plug
HTN9043A Rapid-Rate Intellicharger, 220 Volt, Euro Plug
HTN9044A Rapid-Rate Intellicharger, 240 Volt, UK Plug
Single-Unit Chargers
Single-unit standard chargers can charge NiCd batteries in approximately 16
hours.
HTN9702A Single-Unit Standard Charger, 110 Volt, US Plug
HTN9804A Single-Unit Standard Charger, 220 Volt, Euro Plug
HTN9805A Single-Unit Standard Charger, 240 Volt, UK Plug
Multi-Unit Chargers (MUC)
Multiple unit chargers can be wall or rack mounted and are ideal for
multiple shift operations. They can charge up to 6 batteries simultaneously and are available in a variety of voltages for domestic and
international applications.
HTN9060A6-Pocket, 1-Hour Rapid-Rate Charger
110 Volt - NiCd and NiMH batteries.
HTN9061A6-Pocket, 90-Minute Rapid-Rate Charger
220 Volt - NiCd and NiMH batteries.
HTN9062A6-Pocket, 90-Minute Rapid-Rate Charger
240 Volt - NiCd and NiMH batteries.
HTN9060A
HTN9042A
HTN9702A
28
WALL MOUNT BRACKETS
HLN9293AWall Mount Bracket
For 90-Minute Multi-Unit Chargers
HLN9944AWall Mount Bracket for Multi-Unit Chargers
LTS 2000
essential power...
Motorola Conditioning Charger (MCC)
The MCC features Instant Fault Detection technology that detects faulty batteries in seconds. You'll
know right away when a battery won't operate at peak performance - saving you time and trouble.
Each unit rapidly charges NiCd and NiMH batteries and optimizes battery performance. It’s patented, negative pulse charging process minimizes overheating and overcharging, extending useful battery life. Batteries can be left on the charger for extended periods of time, without worry of heat
build-up. Optional accessories are available that allow the MCC to be used in both AC and DC environments - that’s flexibility.
WPPN4002BRBase Charge Unit, 110 Volt AC. Adapter plates sold separately.
WPPN4006ARBase Charge Unit, 220 Volt AC. Adapter plates sold separately.
WPPN4005CR Adapter Plate Only, 7 Volt
WPLN4088CR Charger Kit, 110 Volt AC. Includes Single-Unit base and 7 Volt adapter plate.
WPLN4089CR Charger Kit, 220 Volt AC. Includes Single-Unit base and 7 Volt adapter plate.
WPPN4065BRMulti-Unit Conditioning Charger, 4-Station Base, 110 Volt
Adapter plates sold separately.
Vehicular Mounting
RLN4814AVehicular Mounting Bracket and DC Hard Wire Cable
For Single-Unit Motorola Conditioning Chargers.
3080384M21 DC Hard Wire Cable with 3 AH In-line fuse.
Vehicular Power Adapter
3080384G15Vehicular Power Adapter
WPPN4065BR
Vehicular Travel Charger
A great traveling companion that ensures constant communication while
on the road. Allows rapid charging of the battery while using the radio.
Users can talk immediately once the charger is connected and transmit from a
previously “dead” battery in just 5 minutes. Includes voltage regulated adapter,
custom charger base, mounting bracket and coil cord. Ideal for public safety, utility
and construction markets.
2580600E05Transformer, US, 120 Volt
2580600E06Transformer, European, 230 Volt
2580600E07Transformer, UK, 230 Volt
2580600E08Transformer, Argentina, 220 Volt
RLN4814A
Vehicular Charger Adapter
The Vehicular Charger Adapter is designed to easily charge batteries in a vehicle by adapting a single-unit, rapid-rate charger to the vehicular power adapter. Ideal for frequent travelers.
HLN9719A Vehicular Charger and Bracket, 12 Volt
For use with HTN9042A, HTN9043A, HTN9044A.
RLN4833A
HLN9719A
29
chargers
WPLN4079BR
Battery Maintenance System
Increase the useful life of your batteries. Using interchangeable battery adapters (sold
separately), the BMS
ing and cycle testing batteries. It supports NiCd, NiMH and Li-ion battery chemistries
(Li-ion 6-station units only) and tracks better voltage and capacity (mAh). Its easy-touse design supports hundreds of two-way, cellular and camcorder batteries. The
PLUS
BMS
offers a 3-year warranty and includes serial printer* port (RS-232).
*Compatible with the STAR Micronics SP200 series printers and other printers with
STAR printer emulation. STAR Micronics printers are available through STAR
Micronics distributors.
PLUS
is capable of charging and discharging, analyzing, condition-
PLUS
Li-ion Field Upgrade Kit. Upgrades WPLN4079AR,
WPLN4080AR, WPLN4081AR.
Allows units to support Li-ion batteries.
Does not support Li-ion or 3-cell batteries.
Does not support Li-ion or 3-cell batteries.
Battery Maintenance System
TDN9437A Adapter, for use with HNN9701A batteries
TDN9662A Adapter, for use with HNN9628A
TDN9438A Adapter, for use with HNN9808B
PLUS
PLUS
, 110 Volt AC, 50/60 Hz, US Plug
PLUS
, 230 Volt AC, 50/60 Hz, Euro Plug
PLUS
, 230 Volt AC, 50/60 Hz, UK Plug
PLUS
(BMS
(BMS
PLUS
)
PLUS
) Adapters
NDN4005B
30
LTS 2000
WPLN4124AR
Battery Optimizing System II (BOS II)
No other battery analyzer matches the speed, accuracy, versatility and ease-of-use of the BOS II in providing powerful analyzing capabilities. Users can select from 12 pre-programmed service programs making it quick and easy to get up and running. Because the BOS II is
programmable, users can create custom programs to perform a wide variety of tasks specific to individual needs. New enhancements
include new navigation keys and an improved, more intuitive menu system. Regular use of the BOS II can optimize battery performance
and help extend battery life, helping reduce battery replacement costs.
WPLN4124AR BOS II, 4-Station, 90-264 Volt AC, US Plug. Adapter Plates Required.
WPLN4125AR BOS II, 4-Station, 90-264 Volt AC, Euro/UK Plug. Adapter Plates Required.
RL71883 Standard Adapter
• Quicktest™ diagnostic feature measures a battery’s state of health in approximately 2 to 5 minutes
• Supports NiCd, NiMH, Li-ion and SLA batteries
• Increased power-programmable from 100mAh to 4 Amps per station
• Programmable adapters allow customization of maintenance routines
• Proprietary reduction cycle restores NiCd and NiMH batteries
• Printer output for reports and labels with computer interface (Includes both 9-pin serial and 25-pin parallel ports)
• 100-Watt Universal Power Supply (110-240 VAC) provides up to 4 amps of power per station
• Interchangeable adapter plates accommodate nearly all Motorola two-way batteries and other major brands batteries
31
Antenna Characteristics
Heliflex antennas are
engineered for maximum
output and coverage.
Stubby antennas are
non-obtrusive, ideal for
audio
wearing the radio
on a belt.
Whip antennas are
one-piece with a steel core
for optimal radiation.
32
LTS 2000
tuned and tested...
Flexible Whip
Flexible whip antennas have a one-piece finish and steel core for optimal radiation characteristics. They provide more comfort when the radio is worn on a belt.
8505241U03 7 Inch Flexible Whip Antenna, 806-869 MHz
Stubby
This quarterwave stubby antenna is ideal when the radio is worn on a belt
because the short antenna is non-obtrusive. This is a broadband antenna that can
be used for both 800 MHz and 900 MHz applications.
8505241U06 4 Inch Stubby Antenna, 806-941 MHz
8505241U06
33
Public Safety
When professionals need their
hands free for important tasks, a
Visor Microphone and foot-oper-
ated Push-to-Talk switch are the
right solution.
Customer Service
One day you’re in the field. The
next day has you
behind a desk. Control Station
MCS 2000 mobile
Accessories make it easy to con-
vert your
radio for inside use.
Private Transportation
Maximizing passenger safety is a
number one priority,
and an Emergency Switch is a
ready solution when an alarm or
help message
needs to be sent.
Delivery Fleets
Hear one number wrong,
and an important package won’t
needed on time. An
External Speaker
everything clear under
noisy conditions.
34
get where it’s
can help make
MCS 2000
full-featured analog operation with the
features users want most...
MCS 2000TMmobile radios can deliver both narrow band and broad band
operation in a compact, space-saving footprint. All models are compatible
with Motorola MTS 2000 portable radios, so they can serve as the
heart of a truly integrated solution.
35
audio and control station
HMN4072E
Microphones and Accessories
HMN4069E Standard White Palm Microphone
HMN4072E Classic White Palm Microphone
NMN6210D 3 x 4 Button Keypad Microphone
Includes three additional
programmable buttons.
GMN6147B Noise-Cancelling Microphone
Includes three additional
programmable buttons.
HMN1085B Handset with Hang Up Cup
Microphone Adapter Cables
Adapter cables allow a second microphone to be added via
a mobile accessory connector. This requires adding a second
Push-to-Talk microphone HMN4069E or HMN4072E, both
sold separately.
HKN6129A 17-Foot Adapter Cable
For second microphone.
HKN6130A 40-Foot Adapter Cable
For second microphone.
Hands-Free Mobile Accessories
The Gooseneck Push-to-Talk and Foot Switch Push-to-Talk
allow mobile users hands-free communication options.
FMN1611C Dash Mount Visor Microphone
Requires GLN7279A or GLN7278B.
HKN6116A 1-Foot Adapter Cable
HMN1073A Remote Mount Visor Microphone
Requires GLN7279A or GLN7278B.
GLN7279A Gooseneck Push-to-Talk
Attaches to vehicle steering column.
GLN7278B Foot Switch Push-to-Talk
Siren and Public Address Speakers
HSN4038A 7.5-Watt External Water Resistant
Speaker. Requires adapter cable
HKN6127A for dash mount.
HSN4039A 13-Watt External Water Resistant
Remote Speaker. Requires adapter
cable HKN6127A for dash mount.
HKN6127A Speaker Adapter Cable
INSTALLATION ACCESSORIES
HLN6356B Installation Hardware Kit
GKN6263A Ignition Sense Cable
HMN4069E
36
HSN4038A
HMN1073A
MCS 2000
Control Station accessories make the MCS 2000 a desktop
command center. From left to right are Desktop Microphone
HMN1038E, Control Station Power Supply HPN4007A,
Control Station Tray HLN6405A.
Control Station Accessories
HMN1038E Desk Microphone. Beige.
HMN3000B Desk Microphone. Black.
HLN6404A Desk Tray with Speaker, Low Power
For use with Models II and III.
HLN6405A Desk Tray without Speaker, Low Power
For use with Model I.
HPN4008B Power Supply, Low Power
HLN6580B Desk Tray with Speaker, Mid Power
For use with Models II & III.
HLN6581A Desk Tray without Speaker, Low Power
For use with Model I.
HPN4007A Power Supply, High Power
Emergency Switches
These switches enable the user to send an emergency message to
a console where their unit ID can be displayed and an alarm
sounded.
GLN7282AAlarm Buzzer
HLN6642AAlarm Relay and Cable
HLN6372AKey Lock Mount
HKN6128AIgnition Switch Cable
GKN6262BCar Radio Mute Cable
HMN3000B
HLN6405A
HLN5113B
37
A communication
system is only
as good as
the mobile antennas
used to transmit
and receive —
so whenever
cables and antennas
lives are on the line
Motorola Original
accessories
should be the
go-to choice.
®
Remote Mount Kits
Converts a low or mid-power radio from dash to remote mount. Includes
17-foot control head cable, 20-foot power cable, 40-foot power cable, control
head back plate and mounting hardware, front plate for the transceiver and an
adapter for the speaker.
H1634A Remote Mount Retrofit Kit. For use with Model I.
H1635A Remote Mount Retrofit Kit. For use with Model II and Ill.
38
REMOTE MOUNT KIT ACCESSORIES
HKN6111B 10-Foot Control Head Cable
HKN6112B 17-Foot Control Head Cable
HKN6113B 22-Foot Control Head Cable
HKN6118B 40-Foot Control Head Cable
Power Cables
HKN4191B 10-Foot, Low/Mid Power Cable
HKN4192B 20-Foot, Low/Mid Power Cable
MCS 2000
Low Profile Antennas
UHF
RAE4162AWhite 410-430 MHz, 3dB Gain Antenna
RAE4163ABlack 410-430 MHz, 3dB Gain Antenna
RAE4164ABlack 430-450 MHz, 3dB Gain Antenna
RAE4165AWhite 430-450 MHz, 3dB Gain Antenna
RAE4166ABlack 470-490 MHz, 3dB Gain Antenna
RAE4167AWhite 450-470 MHz, 3dB Gain Antenna
RAE4168ABlack 450-470 MHz, 3dB Gain Antenna
RAE4169AWhite 470-490 MHz, 3dB Gain Antenna
800 MHz
RAF4217AWhite 821-896 MHz, 3dB Gain Antenna
RAF4218ABlack 821-896 MHz, 3dB Gain Antenna
RAF4219ABlack 806-866 MHz, 3dB Gain Antenna
RAF4220AWhite 806-866 MHz, 3dB Gain Antenna
RAF4220A
HAE4013A
HAE4003A
HAF4002A
Antennas
800 MHz
HAF4002A 806-900 MHz, 1/4 Wave Roof Mount Antenna
RRA4983A 806-900 MHz. 3dB, Roof Mount Antenna
900 MHz
RRA4935A 890-960 MHz, 3dB Roof Mount Antenna with 14 ft. Cable
RAF4003ARM 890-960 MHz, 3dB Roof Mount Antenna with 22 ft. Low Loss Cable
VHF
HAD4006A 136-144 MHz, 1/4 Wave, Roof Mount Antenna
HAD4007A 144-152 MHz, 1/4 Wave, Roof Mount Antenna
HAD4008A 150.8-162 MHz, 1/4 Wave, Roof Mount Antenna
HAD4009A 162-174 MHz, 1/4 Wave, Roof Mount Antenna
RAD4010ARB 136-174 MHz, 3dB, Roof Mount Antenna
UHF
HAE4002A 403-430 MHz, 1/4 Wave, Roof Mount Antenna
HAE4003A 450-470 MHz, 1/4 Wave, Roof Mount Antenna
HAE4004A 470-512 MHz, 1/4 Wave, Roof Mount Antenna
HAE4010A 406-420 MHz, 3.5dB, Roof Mount Antenna
HAE4011A 450-470 MHz, 3.5dB, Roof Mount Antenna
HAE4012A 470-495 MHz, 3.5dB, Roof Mount Antenna
HAE4013A 494-512 MHz, 3.5dB, Roof Mount Antenna
Low Profile Antenna Kits
Includes 3/4 Brass Mount and 17- foot RG58U Solid Center
Conductor Cable.
UHF
RAE4162ARBWhite 410-430 MHz,
3dB Gain Roof Mount Antenna
RAE4163ARBBlack 410-430 MHz,
3dB Gain Roof Mount Antenna
RAE4164ARBBlack 430-450 MHz,
3dB Gain Roof Mount Antenna
RAE4165ARBWhite 430-450 MHz,
3dB Gain Roof Mount Antenna
RAE4166ARBBlack 470-490 MHz,
3dB Gain Roof Mount Antenna
RAE4167ARBWhite 450-470 MHz,
3dB Gain Roof Mount Antenna
RAE4168ARBBlack 450-470 MHz,
3dB Gain Roof Mount Antenna
RAE4169ARBWhite 470-490 MHz,
3dB Gain Roof Mount Antenna
3080384M48
Antenna Mounts
3080384M44Black Magnetic With 12 ft. RG58A/U Cable, Mini-UHF Crimp
3080384M45Chrome Magnetic With 12 ft. RG58A/U Cable, Mini-UHF Crimp
3080384M46Chrome Trunk Mount With 17 ft. RG58A/U Cable, Mini-UHF Crimp
3080384M47Black Trunk Mount With 17 ft. RG58A/U Cable, Mini-UHF Crimp
3080384M483/4 Roof Mount With 17 ft. RG58A/U Cable, Mini-UHF Crimp
800 MHz
RAF4217ARBWhite 821-896 MHz,
3dB Gain Roof Mount Antenna
RAF4218ARBBlack 821-896 MHz,
3dB Gain Roof Mount Antenna
RAF4219ARBBlack 806-866 MHz,
3dB Gain Roof Mount Antenna
RAF4220ARBWhite 806-866 MHz,
3dB Gain Roof Mount Antenna
39
Public Safety
When professionals need to trans-
mit numeric data as well as voice,
a Full Size DTMF Microphone is
easy to use and
comfortable to hold.
Customer Service
One day you’re in the field. The
next day has you
behind a desk. Control Station
GTX and LCS 2000 mobiles
Accessories make it easy to con-
vert your radio for inside use.
Private Transportation
Maximizing passenger safety is a
number one priority,
and an Emergency Switch is a
ready solution when an alarm or
help message needs to be sent.
Delivery Fleets
Hear one number wrong,
and an important package won’t
get where it’s
needed on time. An
External Speaker
everything clear under
noisy conditions.
40
can help make
GTX & LCS 2000
simple two-way communication with
capabilities that are anything but...
GTX and LCS 2000TMmobile radios are easy to use, yet pack a lot of performance into
their compact, space-saving footprint. Offering both local and wide-area coverage,
these models deliver advanced functionality that meets a variety of
communication needs.
41
audio and control station
Microphones
HMN3220B Standard Compact Microphone
HMN1035C Full Size Palm Microphone
HMN3013A Non-Backlit, Full Size DTMF
Microphone
Mounting Bracket
GLN7317A Non-locking Bracket
Cables
GKN6270A Standard Power Cable
GKN6271A Ignition Switch Cable
Control Station accessories make the LCS 2000 mobile a desktop
command center. Shown here is the Low Power Control Station Package
HLN3067B which includes adapter cable, base tray, black desk micro-
phone and power supply.
Control Station
Converts the mobile radio for desktop use for dispatch purposes. Includes adapter cable,
base tray, black desk microphone and power supply.
HLN3067B Low Power Control Station Package
CONTROL STATION ACCESSORIES
HPN4008B Power Supply, Low Power
HLN6405A Desk Tray without Speaker
HMN3000B Desk Microphone
HKN9088B Adapter Cable
HLN6405A
43
A communication
system is only
as good as
the mobile antennas
used to transmit
and receive —
so whenever
cables and antennas
lives are on the line
Motorola Original
accessories
should be the
go-to choice.
®
44
GTX & LCS 2000
Antennas
HAF4002A 806-900 MHz, 1/4 Wave Roof Mount Antenna
RRA4914B 806-900 MHz, 3dB Stainless Steel Roof Mount Antenna
RRA4990A 806-900 MHz, 3dB Black Chrome Roof Mount Antenna
RRA4983A 806-900 MHz, 3dB, Roof Mount Antenna. Low Loss.
RRA4986A 806-900 MHz, 3dB Black Chrome Roof Mount Antenna
RRA4935A 890-960 MHz, 3dB Roof Mount Antenna
RRA4935A
RAF4220A
HAF4002A
RAF4003ARM 890-960 MHz, 3dB Roof Mount Antenna
Low Profile Antennas
RAE4162AWhite 410-430 MHz, 3dB Gain Antenna
RAE4163ABlack 410-430 MHz, 3dB Gain Antenna
RAE4164ABlack 430-450 MHz, 3dB Gain Antenna
RAE4165AWhite 430-450 MHz, 3dB Gain Antenna
RAE4166ABlack 470-490 MHz, 3dB Gain Antenna
RAE4171AWhite 450-470 MHz, 3dB Gain Antenna
RAE4168ABlack 450-470 MHz, 3dB Gain Antenna
RAE4169AWhite 470-490 MHz, 3dB Gain Antenna
800 MHz
Low Loss.
900 MHz
with 14 ft. Cable
with 22 ft. Low Loss Cable
UHF
3080384M48
Antenna Mounts
3080384M44Black Magnetic with 12 ft.
RG58A/U Cable, Mini-UHF Crimp
3080384M45Chrome Magnetic with 12 ft.
RG58A/U Cable, Mini-UHF Crimp
3080384M46Chrome Trunk Mount with 17 ft.
RG58A/U Cable, Mini-UHF Crimp
3080384M47Black Trunk Mount with 17 ft.
RG58A/U Cable, Mini-UHF Crimp
3080384M483/4 Roof Mount with 17 ft.
RG58A/U Cable, Mini-UHF Crimp
HKN9557A
800 MHz
RAF4217AWhite 821-896 MHz, 3dB Gain Antenna
RAF4218ABlack 821-896 MHz, 3dB Gain Antenna
RAF4219ABlack 806-866 MHz, 3dB Gain Antenna
RAF4220AWhite 806-866 MHz, 3dB Gain Antenna
Low Profile Antennas Kits
Includes 3/4 Brass Mount and 17-foot RG58U Solid Center Conductor Cable.
UHF
RAE4162ARBWhite 410-430 MHz, 3dB Gain Roof Mount Antenna
RAE4163ARBBlack 410-430 MHz, 3dB Gain Roof Mount Antenna
RAE4164ARBBlack 430-450 MHz, 3dB Gain Roof Mount Antenna
RAE4165ARBWhite 430-450 MHz, 3dB Gain Roof Mount Antenna
RAE4166ARBBlack 470-490 MHz, 3dB Gain Roof Mount Antenna
RAE4167ARBWhite 450-470 MHz, 3dB Gain Roof Mount Antenna
RAE4168ARBBlack 450-470 MHz, 3dB Gain Roof Mount Antenna
RAE4169ARBWhite 470-490 MHz, 3dB Gain Roof Mount Antenna
800 MHz
RAF4217ARBWhite 821-896 MHz, 3dB Gain Roof Mount Antenna
RAF4218ARBBlack 821-896 MHz, 3dB Gain Roof Mount Antenna
RAF4219ARBBlack 806-866 MHz, 3dB Gain Roof Mount Antenna
RAF4220ARBWhite 806-866 MHz, 3dB Gain Roof Mount Antenna
2880376E84
Antenna Adapters
HKN9557AMini UHF to UHF Adapter Cable
2880376E84Mini UHF Antenna Connector
HLN8027AMini UHF to BNC Connector
45
Call us and order today...
PHONE: 1-800-422-4210
TTY PHONE: 1-866-522-5210
US FEDERAL GOVERNMENT: 1-800-826-1913
FAX: 1-800-622-6210
MOTOROLA ONLINE USERS: http://motorola.com/businessonline