Datasheet MC34184D, MC34184DTB, MC34184P, MC34181P, MC34182D Datasheet (Motorola)




Order this document by MC34181/D

D SUFFIX

PLASTIC PACKAGE

CASE 751

(SO–8)

P SUFFIX

PLASTIC PACKAGE

CASE 626

P SUFFIX

PLASTIC PACKAGE

CASE 646

D SUFFIX

PLASTIC PACKAGE

CASE 751A

(SO–14)

PIN CONNECTIONS

(Single, Top View)

(Dual, Top View)

(Quad, Top View)

4

23

1

PIN CONNECTIONS

Offset Null

V

EE

V

EE

Inputs 1

Output 1

Inputs

NC
V

CC

Output
Offset Null

Inputs 2

Output 2

V

CC

1
2
3
4

8
7
6
5

+

1
2
3
4

8
7
6
5

1

2

1

2

3

4
5

6

78

9

10

11

12

13

14

Inputs 1

Output 1

V

CC

Inputs 2

Output 2

Output 4

Inputs 4

V

EE

Inputs 3

Output 3

–

+

–

+

–

+

–––

+

+
–

+
–

1

8

1

8

14

1

14

1

DTB SUFFIX

PLASTIC PACKAGE

CASE 948G
(TSSOP–14)

14

1

1

MOTOROLA ANALOG IC DEVICE DATA

"( "($  ( &
 !(&  !#'&
#$&"!  #$%

Quality bipolar fabrication with innovative design concepts are employed
for the MC33181/2/4, MC34181/2/4 series of monolithic operational
amplifiers. This JFET input series of operational amplifiers operates at
210 µA per amplifier and offers 4.0 MHz of gain bandwidth product and
10 V/µs slew rate. Precision matching and an innovative trim technique of
the single and dual versions provide low input offset voltages. With a JFET
input stage, this series exhibits high input resistance, low input offset voltage
and high gain. The all NPN output stage, characterized by no deadband
crossover distortion and large output voltage swing, provides high
capacitance drive capability, excellent phase and gain margins, low open
loop high frequency output impedance and symmetrical source/sink AC
frequency response.

The MC33181/2/4, MC34181/2/4 series of devices are specified over the
commercial or industrial/vehicular temperature ranges. The complete series
of single, dual and quad operational amplifiers are available in the plastic
DIP as well as the SOIC surface mount packages.

• Low Supply Current: 210 µA (Per Amplifier)

• Wide Supply Operating Range: ±1.5 V to ±18 V

• Wide Bandwidth: 4.0 MHz

• High Slew Rate: 10 V/µs

• Low Input Offset Voltage: 2.0 mV

• Large Output Voltage Swing: –14 V to +14 V (with ±15 V Supplies)

• Large Capacitance Drive Capability: 0 pF to 500 pF

• Low Total Harmonic Distortion: 0.04%

• Excellent Phase Margin: 67°

• Excellent Gain Margin: 6.7 dB

• Output Short Circuit Protection

• Offered in New TSSOP Package Including the Standard SOIC and

DIP Packages

ORDERING INFORMATION

Op Amp

Function

Device

Operating

Temperature Range

Package

Single MC34181P

MC34181D

TA = 0° to +70°C

Plastic DIP

SO–8

MC33181P
MC33181D

TA = –40° to +85°C

Plastic DIP

SO–8

Dual MC34182P

MC34182D

TA = 0° to +70°C

Plastic DIP

SO–8

MC33182P
MC33182D

TA = –40° to +85°C

Plastic DIP

SO–8

Quad MC34184P

MC34184D

MC34184DTB

TA = 0° to +70°C

Plastic DIP

SO–14

TSSOP–14

MC33184P
MC33184D

MC33184DTB

TA = –40° to +85°C

Plastic DIP

SO–14

TSSOP–14

 Motorola, Inc. 1996 Rev 1

MC34181,2,4 MC33181,2,4

2

MOTOROLA ANALOG IC DEVICE DATA

MAXIMUM RATINGS

Rating Symbol Value Unit

Supply Voltage (from VCC to VEE) V

S

+36 V

Input Differential Voltage Range V

IDR

Note 1 V

Input Voltage Range V

IR

Note 1 V

Output Short Circuit Duration (Note 2) t

SC

Indefinite sec

Operating Junction Temperature T

J

+150 °C

Storage Temperature Range T

stg

–60 to +150 °C

NOTES: 1. Either or both input voltages should not exceed the magnitude of VCC or VEE.

2.Power dissipation must be considered to ensure maximum junction temperature (TJ) is not
exceeded (see Figure 1).

Q

8

Internal

Bias

Network

Neg Pos

V

CC

V

O

V

EE

J

1

J

2

Q

9

Q

7

D

3

D

1

C

1

R

6

D

2

R

7

C

2

Q

4

Q

6

Q

5

I

4

R

5

R

4

R

2

Q

3

I

3

R

3

R

1

Q

2

Q

1

Null Offsets

MC3X181 (Single) Only

1

5

1

5

V

EE

MC3X181 Input Offset
Voltage Null CIrcuit

25 k

Ω

–
+

+

Representative Schematic Diagram

(Each Amplifier)

MC34181,2,4 MC33181,2,4

3

MOTOROLA ANALOG IC DEVICE DATA

DC ELECTRICAL CHARACTERISTICS (V

CC

= +15 V , VEE = –15 V , TA = 25°C, unless otherwise noted.)

Characteristics Symbol Min Typ Max Unit

Input Offset Voltage (RS = 50 Ω, VO = 0 V)

Single

TA = +25°C
TA = 0° to +70°C (MC34181)
TA = –40° to +85°C (MC33181)

Dual

TA = +25°C
TA = 0° to +70°C (MC34182)
TA = –40° to +85°C (MC33182)

Quad

TA = +25°C
TA = 0° to +70°C (MC34184)
TA = –40° to +85°C (MC33184)

V

IO

—
—
—

—
—
—

—
—
—

0.5
—
—

1.0
—
—

4.0
—
—

2.0

3.0

3.5

3.0

4.0

4.5

10
11

11.5

mV

Average Temperature Coefficient of VIO (RS = 50 Ω, VO = 0V) ∆VIO/∆T — 10 — µV/°C
Input Offset Current (VCM = 0 V, VO = 0V)

TA = +25°C
TA = 0° to +70°C
TA = –40° to +85°C

I

IO

—
—
—

0.001
—
—

0.05

1.0

2.0

nA

Input Bias Current (VCM = 0 V, VO = 0V)

TA = +25°C
TA = 0° to +70°C
TA = –40° to +85°C

I

IB

—
—
—

0.003
—
—

0.1

2.0

4.0

nA

Input Common Mode Voltage Range V

ICR

(VEE +4.0 V) to (VCC –2.0 V) V

Large Signal Voltage Gain (RL = 10 kΩ, VO = ±10 V)

TA = +25°C
TA = T

low

to T

high

A

VOL

25
15

60

—

—
—

V/mV

Output Voltage Swing (VID = 1.0 V, RL = 10 kΩ)

TA = +25°C

VO+
VO–

+13.5

—

+14
–14

—

–13.5

V

Common Mode Rejection (RS = 50 Ω, VCM = V

ICR

, VO = 0 V) CMR 70 86 — dB
Power Supply Rejection (RS = 50 Ω, VCM = 0 V, VO = 0 V) PSR 70 84 — dB
Output Short Circuit Current (VID = 1.0 V , Output to Ground)

Source
Sink

I

SC

3.0

8.0

8.0
11

—
—

mA

Power Supply Current (No Load, VO = 0 V)

Single

TA = +25°C
TA = T

low

to T

high

Dual

TA = +25°C
TA = T

low

to T

high

Quad

TA = +25°C
TA = T

low

to T

high

I

D

—
—

—
—

—
—

210

—

420

—

840

—

250
250

500
500

1000
1000

µA

MC34181,2,4 MC33181,2,4

4

MOTOROLA ANALOG IC DEVICE DATA

AC ELECTRICAL CHARACTERISTICS

(VCC = +15 V , VEE = –15 V , TA = 25°C, unless otherwise noted.)

Characteristics Symbol Min Typ Max Unit

Slew Rate (Vin = –10 V to +10 V, RL = 10 kΩ, CL = 100 pF)

AV = +1.0
AV = –1.0

SR

7.0
—

10
10

—
—

V/µs

Settling Time (AV = –1.0, RL = 10 kΩ, VO = 0 V to +10 V Step)

To Within 0.10%
To Within 0.01%

t

s

—
—

1.1

1.5

—
—

µs

Gain Bandwidth Product (f = 100 kHz) GBW 3.0 4.0 — MHz
Power Bandwidth (AV = +1.0, RL = 10 kΩ, VO = 20 Vpp, THD = 5.0%) BW

p

— 120 — kHz

Phase Margin (–10 V < VO < +10 V)

RL = 10 kΩ
RL = 10 kΩ, CL = 100 pF

f

m

—
—

67
34

—
—

Degrees

Gain Margin (–10 V < VO < +10 V)

RL = 10 kΩ
RL = 10 kΩ, CL = 100 pF

A

m

—
—

6.7

3.4

—
—

dB

Equivalent Input Noise Voltage

RS = 100 Ω, f = 1.0 kHz

e

n

— 38 —

nV/ Hz√

Equivalent Input Noise Current

f = 1.0 kHz

i

n

— 0.01 —

pA/ Hz√

Differential Input Capacitance C

i

— 3.0 — pF

Differential Input Resistance R

i

— 10

12

— W

Total Harmonic Distortion

AV = 10, RL = 10 kΩ, 2.0 Vpp < VO < 20 Vpp, f = 1.0 kHz

THD — 0.04 — %

Channel Separation (RL = 10 kΩ, –10 V < VO < +10 V, 0 Hz < f < 10 kHz) — — 120 — dB
Open Loop Output Impedance

(f = 1.0 MHz)

|Zo| — 200 — Ω

8/14 Pin

Plastic

SO–8

SO–14

Figure 1. Maximum Power Dissipation versus

Temperature for Package Variations

Figure 2. Input Common Mode Voltage Range

versus Temperature

TA, AMBIENT TEMPERATURE (°C)

D

P , MAXIMUM POWER DISSIPATION (mW)

–55 –40 –20 0 20 40 60 80 100 120 140 160

TA, AMBIENT TEMPERATURE (°C)

ICR

V , INPUT COMMON MODE VOLTAGE

RANGE (V)

–55 –25 0 25 50 75 100 125

VCC = +3.0 V to +15 V
VEE = –3.0 V to –15 V

∆

VIO = 5.0 mV

VCC (VCM to VCC)

V

EE

2400

2000

1600

1200

800

400

0

0

–1.0

–2.0

3.0

2.0

1.0

0

TSSOP–14

MC34181,2,4 MC33181,2,4

5

MOTOROLA ANALOG IC DEVICE DATA

V

EE

V

CC

VCC = +15 V
VEE = –15 V
TA = +25

°

C

Figure 3. Input Bias Current

versus Temperature

Figure 4. Input Bias Current versus

Input Common Mode Voltage

Figure 5. Output Voltage Swing

versus Supply Voltage

Figure 6. Output Saturation Voltage

versus Load Current

Figure 7. Output Saturation Voltage versus

Load Resistance to Ground

Figure 8. Output Saturation Voltage versus

Load Resistance to V

CC

TA, AMBIENT TEMPERATURE (°C)

IB

I , INPUT BIAS CURRENT (nA)

–55 –25 0 25 50 75 100 125

VCC = +15 V
VEE = –15 V
VCM = 0 V

V

ICR

, INPUT COMMON MODE VOLTAGE (V)

–10 –5.0 0 5.0 10

VCC = +15 V
VEE = –15 V
TA = 25

°

C

VCC, |VEE|, SUPPLY VOLTAGE (V)

0 2.0 4.0 6.0 8.0 10 12 14 16

V

O

, OUTPUT VOLTAGE SWING (V)

RL Connected to Ground

TA = 25

°

C

RL = 10 k

IL, LOAD CURRENT (mA)

Sink

0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10

VCC = +15 V
VEE = –15 V
TA = +25

°

C

Source

sat

V , OUTPUT SA TURATION VOLTAGE (V)

RL, LOAD RESISTANCE T O GROUND (Ω)

1.0 k 10 k 100 k 1.0 M

V

EE

V

CC

VCC = +15 V
VEE = –15 V
TA = +25

°

C

RL, LOAD RESISTANCE (Ω)

1.0 k 10 k 100 k 1.0 M

V

CC

V

EE

sat

V , OUTPUT SA TURATION VOLTAGE (V)

sat

V , OUTPUT SA TURATION VOLTAGE (V)

IB

I , INPUT BIAS CURRENT (nA)

1000

100

10

1.0

0.1

0.01

0.001

20

15

10

5

0

40

30

20

10

0

0
–1.0
–2.0

–3.0

+3.0
+2.0
+1.0

0

0

–1.0
–2.0
–3.0

3.0

2.0

1.0
0

0

–1.0
–2.0
–3.0

3.0

2.0

1.0
0

MC34181,2,4 MC33181,2,4

6

MOTOROLA ANALOG IC DEVICE DATA

100

10

1.0

AV = 1000

VCC = +15 V
VEE = –15 V
VO = 2.0 V

pp

RL = 10 k

Ω

TA = 25°C

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

THD = 1.0%
TA = 25

°

C

100 10

AV = 1000

1.0

VCC = +15 V
VEE = –15 V
VCM = 0 V
VO = 0 V

∆

IO = 10 µA

TA = 25

°

C

A , OPEN LOOP VOLTAGE GAIN (dB)

Figure 9. Output Short Circuit Current

versus Temperature

Figure 10. Output Impedance versus Frequency

Figure 11. Output Voltage Swing

versus Frequency

Figure 12. Output Distortion versus

Frequency

Figure 13. Open Loop Voltage Gain

versus Temperature

Figure 14. Open Loop Voltage Gain and

Phase versus Frequency

TA, AMBIENT TEMPERATURE (°C)

SC

I , OUTPUT SHORT CIRCUIT CURRENT (mA)

–55 –25 0 25 50 75 100 125

Sink

Source

VCC = +15 V
VEE = –15 V
RL

≤

0.1

Ω

VID = 1.0 V

f, FREQUENCY (Hz)

O

|Z |, OUTPUT IMPEDANCE ( )

Ω

100 1.0 k 10 k 100 k 1.0 M

f, FREQUENCY (Hz)

1.0 k 10 k 109 k 1.0 M

,

V

O

OUTPUT VOL TAGE SWING (V

p–p

)

f, FREQUENCY (Hz)

THD, TOT AL HARMONIC DISTORTION (%)

10 100 1.0 k 10 k 100 k

VOL

A , OPEN LOOP VOLTAGE GAIN (V/mV)

TA, AMBIENT TEMPERATURE (°C)

–55 –25 0 25 50 75 100 125

f, FREQUENCY (Hz)

VOL

1.0 10 100 1.0 k 10 k 1.0 M 10 M 100 M100 k

Phase

Gain

, EXCESS PHASE (DEGREES)

φ

30

20

10

0

300

200

100

0

30

24

18

12

6

0

1.0

0.8

0.6

0.4

0.2

0

70

60

50

40

30

20

100

80

60

40

20

0

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

f ≤ 10 Hz
TA = 25

°

C

VCC = +15 V
VEE = –15 V
VO = 0 V
RL = 10 k

Ω

TA = 25°C

0

45

90

135

180

MC34181,2,4 MC33181,2,4

7

MOTOROLA ANALOG IC DEVICE DATA

CL = 100 pF

CL = 10 pF

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

to

∞

–10 V < VO < +10 V

Figure 15. Normalized Gain Bandwidth

Product versus Temperature

Figure 16. Output Voltage Overshoot

versus Load Capacitance

Figure 17. Phase Margin versus

Load Capacitance

Figure 18. Gain Margin versus

Load Capacitance

Figure 19. Phase Margin

versus Temperature

Figure 20. Gain Margin

versus Temperature

TA, AMBIENT TEMPERATURE (°C)

GBW, GAIN BANDWIDTH PRODUCT (NORMALIZED)

–55 –25 0 25 50 75 100 125

CL, LOAD CAPACITANCE (pF)

OS

V , OUTPUT VOLTAGE OVERSHOOT (%)

10 100 1.0 k

CL, LOAD CAPACITANCE (pF)

, PHASE MARGIN (DEGREES)

φ

m

10 100 1.0 k

CL, LOAD CAPACITANCE (pF)

A

m

, GAIN MARGIN (dB)

10 100 1.0 k

, PHASE MARGIN (DEGREES)

φ

m

–55 –25 0 25 50 75 100 125

TA, AMBIENT TEMPERATURE (

°

C) TA, AMBIENT TEMPERATURE (°C)

CL = 100 pF

CL = 10 pF

A

m

, GAIN MARGIN (dB)

–55 –25 0 25 50 75 100 125

1.3

1.2

1.1

0.9

0.8

0.7

1.0

100

80

60

40

20

0

70
60
50
40
30
20
10

0

10

8.0

6.0

4.0

2.0

0

70

60

50

40

30

20

10

10

9.0

8.0

7.0

6.0

5.0

4.0

3.0

2.0

1.0
0

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

∆

VO = 100 mV

pp

–10 V < VO < +10 V
AV = +1.0
TA = 25

°

C

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

to

∞

–10 V < VO < +10 V
TA = 25

°

C

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

to

∞

–10 V < VO < +10 V
TA = 25

°

C

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

to

∞

–10 V < VO < +10 V

MC34181,2,4 MC33181,2,4

8

MOTOROLA ANALOG IC DEVICE DATA

+PSR (∆VCC = ±1.5 V)

–PSR (∆VEE = ±1.5 V)

+PSR = 20Log

∆

VO/A

DM

∆

V

CC

–PSR = 20Log

∆

VO/A

DM

∆

V

EE

VCC = +15 V
VEE = –15 V
TA = 25

°

C

∆

V

CC

∆

V

EE

A

DM

–
+

∆

V

O

|I |, I , SUPPLY CURRENT (NORMALIZED)

Figure 21. Normalized Slew Rate

versus Temperature

Figure 22. Common Mode Rejection

versus Frequency

Figure 23. Input Noise Voltage

versus Frequency

Figure 24. Power Supply Rejection

versus Temperature

Figure 25. Power Supply Rejection

versus Frequency

Figure 26. Normalized Supply Current

versus Supply Voltage

TA, AMBIENT TEMPERATURE (°C)

SR, SLEW RATE (NORMALIZED)

–55 –25 0 25 50 75 100 125

f, FREQUENCY (Hz)

CMR, COMMON MODE REJECTION (dB)

100 1.0 k 10 k 100 k 1.0 M

f, FREQUENCY (Hz)

e

n

, INPUT NOISE VOL TAGE ( )

10 100 1.0 k 10 k 100 k

nV/ Hz

√

TA < AMBIENT TEMPERATURE (°C)

PSR, POWER SUPPLY REJECTION (dB)

–55 –25 0 25 50 75 100 125

Positive Supply

Negative Supply

∆

VCC, ∆VEE = 3.0 V

f

≤

10 Hz

f, FREQUENCY (Hz)

PSR, POWER SUPPLY REJECTION (dB)

100 1.0 k 10 k 100 k 1.0 M

VCC, |VEE|, SUPPLY VOLTAGE (V)

EE CC

0 5.0 10 15

20

TA = 25°C

125

°

C

–55

°

C

1.1

1.0

0.9

0.8

0.7

0.6

0.5

140
120
100

80
60
40
20

0

100

80

60

40

20

0

110

100

90

80

140
120

100

80
60
40
20

0

1.2

1.1

1.0

0.9

0.8

0.7

VCC = +15 V
VEE = –15 V
AV = +1.0
RL = 10 k

Ω

CL = 100 pF
Vin = –10 V to +10 V

VCC = +15 V
VEE = –15 V

∆

VCM = 3.0 V

TA = 25

°

C

VCC = +15 V
VEE = –15 V
VCM = 0 V
TA = 25

°

C

VCC = +15 V
VEE = –15 V
TA = 25

°

C

RL =

∞

VO = 0V

CMR = 20 Log

A

DM

–
+

∆

V

CM

∆

V

O

X A

DM

∆

V

CM

∆

V

O

MC34181,2,4 MC33181,2,4

9

MOTOROLA ANALOG IC DEVICE DATA

Figure 27. Channel Separation versus Frequency Figure 28. Transient Response

Figure 29. Small Signal Transient Reponse

f, FREQUENCY (Hz)

CHANNEL SEPARATION (dB)

10 k 100 k 1.0 M 10 M

VCC = +15 V
VEE = –15 V
TA = +25

°

C

O

V , OUTPUT VOLTAGE (5.0 V/DIV)

t, TIME (2.0 µs/DIV)

O

V , OUTPUT VOLTAGE (20 mV/DIV)

t, TIME (0.5 µs/DIV)

VCC = +15 V
VEE = –15 V
RL = 10 k

Ω

AV = +1.0
TA = 25

°

C

VCC = +15 V

VEE = –15 V
RL = 10 k

Ω

AV = +1.0
TA = 25

°

C

140
120
100

80
60
40
20

0

MC34181,2,4 MC33181,2,4

10

MOTOROLA ANALOG IC DEVICE DATA

P SUFFIX

PLASTIC PACKAGE

CASE 626–05

ISSUE K

D SUFFIX

PLASTIC PACKAGE

CASE 751–05

(SO–8)

ISSUE R

OUTLINE DIMENSIONS

NOTES:

1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.

2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).

3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

14

58

F

NOTE 2

–A–

–B–

–T–

SEATING
PLANE

H

J

G

D

K

N

C

L

M

M

A

M

0.13 (0.005) B

M

T

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A 9.40 10.16 0.370 0.400
B 6.10 6.60 0.240 0.260
C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020
F 1.02 1.78 0.040 0.070
G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
K 2.92 3.43 0.115 0.135
L 7.62 BSC 0.300 BSC
M ––– 10 ––– 10
N 0.76 1.01 0.030 0.040

__

SEATING
PLANE

1

4

58

A0.25MCB

SS

0.25MB

M

h

q

C

X 45

_

L

DIM MIN MAX

MILLIMETERS

A 1.35 1.75

A1 0.10 0.25

B 0.35 0.49
C 0.18 0.25
D 4.80 5.00
E

1.27 BSCe

3.80 4.00

H 5.80 6.20
h

0 7

L 0.40 1.25

q

0.25 0.50

__

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.

2. DIMENSIONS ARE IN MILLIMETERS.

3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.

D

E

H

A

B

e

B

A1

C

A

0.10

MC34181,2,4 MC33181,2,4

11

MOTOROLA ANALOG IC DEVICE DATA

P SUFFIX

PLASTIC PACKAGE

CASE 646–06

ISSUE L

D SUFFIX

PLASTIC PACKAGE

CASE 751A–03

(SO–14)

ISSUE F

OUTLINE DIMENSIONS – continued

NOTES:

1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE
POSITION AT SEATING PLANE AT MAXIMUM
MATERIAL CONDITION.

2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.

3. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.

4. ROUNDED CORNERS OPTIONAL.

17

14 8

B

A

F

HG D

K

C

N

L

J

M

SEATING
PLANE

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A 0.715 0.770 18.16 19.56
B 0.240 0.260 6.10 6.60
C 0.145 0.185 3.69 4.69
D 0.015 0.021 0.38 0.53
F 0.040 0.070 1.02 1.78
G 0.100 BSC 2.54 BSC
H 0.052 0.095 1.32 2.41
J 0.008 0.015 0.20 0.38
K 0.115 0.135 2.92 3.43
L 0.300 BSC 7.62 BSC
M 0 10 0 10
N 0.015 0.039 0.39 1.01

____

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.

–A–

–B–

G

P

7 PL

14 8

71

M

0.25 (0.010) B

M

S

B

M

0.25 (0.010) A

S

T

–T–

F

R

X 45

SEATING
PLANE

D 14 PL

K

C

J

M

_

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A 8.55 8.75 0.337 0.344
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009

M 0 7 0 7

P 5.80 6.20 0.228 0.244
R 0.25 0.50 0.010 0.019

____

MC34181,2,4 MC33181,2,4

12

MOTOROLA ANALOG IC DEVICE DATA

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:

USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF [e-mail] – TOUCHT ONE 602–244–6609 ASIA/P ACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

INTERNET: http://Design–NET.com 51 Ting Ko k Road, Tai Po, N.T., Hong Kong. 852–26629298

MC34181/D

*MC34181/D*

◊