Motorola KEM-ML34301B User Manual

®

wo-Way Radio

T

ser Guide

U

KEM-ML34301B

For More Information

For further information, you may call Motorola Solutions, Inc.

at 1-800-448-6686 (US and Canada) e-mail us at

[e-mail] or visit us on the

Internet at www.motorolasolutions.com/talkabout.

MT Series

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the
general safety information in user guides published prior to
December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To
control your exposure and ensure compliance with the general
population/ uncontrolled environment exposure limits, always
adhere to the following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the
radio generates measurable RF energy exposure only when
transmitting (in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF
energy exposure standards and guidelines:

• United States Federal Communications Commission, Code of
Federal Regulations; 47CFR part 2 sub-part J.

• American National Standards Institute (ANSI)/Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition.

• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.

• Ministry of Health (Canada) Safety Code 6. Limits of Human
Exposure to Radiofrequency Electromagnetic Fields in the
Frequency Range from 3 KHz to 300 GHz, 1999.

• Australian Communications Authority Radiocommunications
(Electromagnetic Radiation—Human Exposure) Standard,

2003.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.

• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.

o ensure optimal radio performance and make sure human

T

xposure to radio frequency electromagnetic energy is within

e

he guidelines set forth in the above standards, always adhere

t
to the following procedures.

ortable Radio Operation and EME Exposure

P

ntenna Care

A

se only the supplied or an approved replacement antenna.

U

nauthorized antennas, modifications, or attachments could

U
damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding
the antenna affects its effective range.

ody-Worn Operation

B

To maintain compliances with FCC/Health Canada RF exposure
guidelines if you wear a radio on your body when transmitting
always place the radio in a Motorola-supplied or approved clip

older, holster, case or body harness for this product. Use of

h

on-Motorola-approved accessories may exceed FCC/Health

n

anada RF exposure guidelines.

C

f you do not use one of the Motorola-supplied or approved

I
body-worn accessories and are not using the radio held in the
normal use position, ensure the radio and its antenna are at

least 1 inch (2.5 cm) from your body when transmitting.

ata Operation

D

If applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna

at least one inch (2.5 cm) from the body.

pproved Audio Accessories

A

• 53724: Remote Speaker with Push-to-Talk Microphone

• 53725: Headset with Swivel Boom Microphone

• 53727: Earbud with Push-to-Talk Microphone

• 53728: Flexible Ear Receiver
56320: Earpiece with Boom Microphone

•

Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic
compatibility. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received,

including interference that may cause undesired operation.

IC Canada

The term "IC:" before the equipment certification number only
signifies that the Industry Canada technical specifications were
met.

Facilities

To avoid electromagnetic interference and/or compatibility
conflicts, turn off your radio in any facility where posted notices
instruct you to do so. Hospitals or health care facilities may be
using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an
aircraft. Any use of a radio must be in accordance with
applicable regulations per airline crew instructions.

M edical Devices – Pacemakers

The Advanced Medical Technology Association recommends
that a minimum separation of 6 inches (15 cm) be maintained
between a handheld wireless radio and a pacemaker. These
recommendations are consistent with the independent research
by and recommendations of the U.S. Food and Drug
Administration.

People with pacemakers should:

• ALWAYS keep the radio more than 6 inches (15 cm) from

their pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the

potential for interference.

• Turn the radio OFF immediately if there is any reason to

suspect that interference is taking place.

M edical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing
aids. In the event of such interference, you may want to consult
your hearing aid manufacturer to discuss alternatives.

1

edical Devices – Other

M

f you use any other personal medical device, consult the

I

anufacturer of your device to determine if it is adequately

m
shielded from RF energy. Your physician may be able to assist
you in obtaining this information.

afety and General Use While Driving

S

Check the laws and regulations regarding the use of radios in
the area where you drive, and always obey them. If you do use
your radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

Pull off the road and park before making or answering a call

•
if driving conditions so require.

he use of a two-way radio while engaged in activities requiring

T
concentration may cause distraction or otherwise impair your
ability to safely participate in such activities. Always use
technology safely.

Do not place a portable radio in the area over an air bag or in the

ir bag deployment area. Air bags inflate with great force. If a

a

ortable radio is placed in the air bag deployment area and the

p

ir bag inflates, the radio may be propelled with great force and

a
cause serious injury to occupants of the vehicle.

otentially Explosive Atmospheres

P

urn off your radio prior to entering any area with a potentially

T
explosive atmosphere. Only radio types that are especially
qualified should be used in such areas as “Intrinsically Safe.”

o not remove, install or charge batteries in such areas. Sparks

D

n a potentially explosive atmosphere can cause an explosion or

i
fire resulting in bodily injury or even death.

Note: The areas with potentially explosive atmospheres referred
to above include fueling areas such as below decks on boats,
fuel or chemical transfer or storage facilities, areas where the air
contains chemicals or particles (such as grain, dust or metal
powders) and any other area where you would normally be
advised to turn off your vehicle engine. Areas with potentially
explosive atmospheres are often—but not always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off
your radio when you are near electrical blasting caps, in a
blasting area, or in areas posted “Turn off two-way radios.”
Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor
burn can result.

Batteries

All batteries can cause property damage and/or bodily injury such
as burns if a conductive material—like jewelry, keys or beaded
chains— touch exposed terminals. The conductive material may
complete an electrical circuit (short circuit) and become quite hot.
Exercise care in handling any charged battery, particularly when
placing it inside a pocket, purse or other container with metal
objects.

Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has received
a sharp blow, or has been dropped or damaged in any way.

3. Never alter the AC cord or plug provided with the unit. If the
plug will not fit the outlet, have the proper outlet installed by
a qualified electrician. An improper condition can result in a
risk of electric shock.

4. To reduce the risk of damage to the cord or plug, pull the
plug rather than the cord when disconnecting the charger
from the AC receptacle.

5. To reduce the risk of electric shock, unplug the charger from
the outlet before attempting any maintenance or cleaning.

6. Use of an attachment not recommended or sold by Motorola
may result in a risk of fire, electric shock or personal injury.

7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress.

MT Series

8. An extension cord should not be used unless absolutely

MON

MENU

Emergency Alert

Flash Light LED

Menu/ Keypad Lock

Scan/Monitor

Speaker

Accessory Port

LED Indicator

Call Tone

Microphone

Flash Light
Button

Volume

Push to Talk
(High)

Push to Talk
(Low)

Scroll/Weather

Mini-USB
Charging Port

Numbers for Codes

Numbers for Channel,
Call Tone

—Battery Meter

—Channel Power
Indicator
(see menu Options)

—Keypad Lock

—Talk Confirmation
Tone (Roger Beep)

—Noise Filtering

—On/Off for each
feature

—Scan

—Call Tone,
Keypad Tone

—Weather Alert

—Hands-Free Use
Without

Accessories

—Hands-Free Use
With Accessories

—Dual Scan

—Vibrate

necessary. Use of an improper extension cord could result

n a risk of a fire and/or electric shock. If an extension cord

i

ust be used, make sure that:

m

• The pins on the plug of the extension cord are the same
umber, size and shape as those on the plug of the

n

harger.

c

• The extension cord is properly wired and in good
ondition.

c

• The extension cord size is 18 AWG for lengths up to 100

eet, and 16 AWG for lengths up to 150 feet.

f

9. The supply cord of the AC adaptor cannot be replaced.
f the cord is damaged, call customer service at

I

-800-448-6686 (U.S. and Canada) or e-mail us at

1

[e-mail].

c

Licensing Information

our Motorola radio operates on FRS & GMRS frequencies in

Y

anada & in the USA. For Canadian citizens, use of these

C
frequencies is subject to the rules & regulations of Industry
Canada (IC). IC requires no license when operated in Canada.

or USA citizens, use is subject to the rules and regulations of

F
the Federal Communications Commission (FCC) . The FCC
requires that all operators using GMRS frequencies obtain a
radio license before operating their equipment. To obtain the FCC
forms, please visit the FCC’s Web site at

ireless.fcc.gov/uls/index.htm?job=home to source form 605 and

w
159, which includes all the instructions you will need. If you wish

o have the document faxed or mailed, or if you have questions,

t

or a fax:

F

Contact the

Fax-0n-Demand

system

1-202-418-0177 1-800-418-FORM

or mail service:

F

Call the FCC

Forms Hotline

(3676)

f you have

I

questions about

the FCC License:

Call the FCC

1-888-CALL-FCC

(225-5322)

please use the following contact information:

Changes or modifications not expressly approved by Motorola
may void the user’s authority granted by the IC/FCC to operate
this radio and should not be made. To comply with IC/FCC
requirements, transmitter adjustments should be made only by
or under the supervision of a person certified as technically
qualified to perform transmitter maintenance and repairs in the
private land, mobile and fixed services as certified by an
organization representative of the user of those services.
Replacement of any transmitter component (crystal,
semiconductor, etc.) not authorized by the IC/FCC equipment
authorization for this radio could violate IC/FCC rules.

Note: Use of this radio outside the country where it was
intended to be distributed is subject to government regulations
and may be prohibited.

Control Buttons

isplay Screen Guide

D

Getting Started

eatherproof

W

This radio is weatherproof to IP-54 standards. It is
dust/splashproof from any direction. The radio is resistant to
water and rain splashes only when the battery cover and

eadset accessory mini-USB ports are sealed. Open the battery

h

ompartment door or headset port cover only when the radio is

c

ry. Use of a headset accessory should be in dry environments

d
only.

The charging base and AC adaptor are not waterproof. Do not
expose the charger to rain or snow. Charge the radios only in a
dry location. Do not place wet radios into the charging base. The
battery door must be tightly closed with the screw to maintain the
weatherproof seal of the radio.

Installing the Batteries

Each radio can use either 1 NiMH rechargeable battery pack or
3 AA alkaline batteries and beeps when the batteries are low.

Installing NiMH Rechargeable Battery Pack

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

3. Remove the NiMH battery pack from the clear plastic bag

4. Insert the NiMH battery pack with the diagram facing you.

5. Close the battery cover and tighten the retaining screw on

Installing the Three AA Alkaline Batteries (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

3. Insert the three AA alkaline batteries with + and - polarity as

4. Close the battery cover and tighten the retaining screw on

Radio Battery Meter

The radio battery icon shows the battery charge level, from full

radio chirps periodically or after releasing (Low Battery
Alert).

Removing the NiMH Battery Pack

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

3. Remove the NiMH battery pack by pulling the ribbon

screw on the battery door and open the cover.

(do not disassemble or unwrap the battery pack).

(The ribbon should be underneath the battery pack and
should wrap around the right side of the pack for easy
removal.)

the battery door.

screw on the battery door and open the cover.

shown inside. (The ribbon should be underneath the AA
alkaline batteries and should wrap around the right side of
the batteries.)

the battery door.

to empty . When the radio has one segment left, the

screw on the battery door and open the cover.

attached to the radio.

2

. Close the battery cover and tighten the retaining screw on

4

the battery door.

emoving the Three AA Alkaline Batteries (Optional Accessory)

R

. Turn the radio off.

1

. With the back of the radio facing you, loosen the retaining

2

crew on the battery door and open the cover.

s

. Gently remove each alkaline battery by easing each battery

3

ut individually.

o

. Close the battery cover and tighten the retaining screw on

4

he battery door.

t

Notes

Exercise care when removing NiMH or AA batteries. Do not

•
se sharp or conductive tools to remove either of these

u

atteries.

b

Remove the batteries before storing your radio for extended

•
eriods of time. Batteries corrode over time and may cause

p

ermanent damage to your radio.

p

sing the mini-USB Charging Adaptor

U

he mini-USB charging adaptor allows you to conveniently

T

harge your NiMH battery pack. This is an alternative to

c
charging your NiMH battery pack in the Battery Charger desk
stand using the AC wall adaptor and especially useful when
used while traveling.

Available mini-USB charging options:

1. Vehicle charger

. Mini-USB computer cable

2

f using a computer, the computer must be turned on.

I

his and other accessories (sold separately) are available for

T

our radio. For more information, visit our Web site at

y

otorolasolutions.com/talkabout.

m

. Plug your mini-USB cable or charger into a power source as

1

is appropriate for your accessory.

2. Plug the cable into the mini-USB port on the bottom of your

radio.

3. After the initial charge, an empty battery will be fully charged

in 7 hrs. for the MT350 series radio (KEBT-650 mAh NiMH
battery pack) or 14 hrs. for the MT352 series radio (KEBT-1300
mAh NiMH battery pack).

4. The battery icon will scroll as the battery is being charged.

The scrolling icon will stop when the battery is fully charged.

Notes

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger

within 16 hours. Do not store the radio while connected to
the charger.

• If the radio is kept on while charging, the charging time will

be extended.

• Even though the charger is connected, you may not be able

to transmit a message if the battery is completely empty .
Allow time for the battery to charge to 1 bar before
attempting to transmit a message.

Attaching and Removing the Belt Clip

1. Attach belt clip to pocket or belt strap.

2. Align the belt clip post with the hole in the back of the radio.

3. Gently push until the clip clicks in place.

To Remove

1. Push down on the release tab at the top of the belt clip to

release the catch.

2. Pull the belt clip away from the back of the radio.

Using the Desktop Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a
desk or workbench. Charge the NiMH battery overnight (at least
16 hours) before using it for the first time.

MT350R Radio

After the initial charge, an empty battery (KEBT-650 mAh NiMH)
is fully charged within 7 hrs.

MT352R Radio

After the initial charge, an empty battery (KEBT-1300 mAh NiMH)
is fully charged within 14 hrs.

MT Series

1. Follow the steps above to install a NiMH Battery Pack.

Flash Light LED

Menu/ Keypad Lock

Scan/Monitor

Speaker

Accessory Port

LED Indicator

—Scan

—Dual Scan

—Vibrate

Numbers for Codes

Numbers for Channel,
Call Tone

—Battery Meter

—Channel Power
Indicator
(see menu Options)

—Keypad Lock

—Talk Confirmation
Tone (Roger Beep)

—Noise Filtering

—On/Off for each
feature

—Scan

—Call Tone,
Keypad Tone

—Weather Alert

—Hands-Free Use
Without
Accessories

—Hands-Free Use
With Accessories

—Dual Scan

—Vibrate

Emergency Alert

Call Tone

Microphone

Flash Light
Button

Volume

Push to Talk
(High)

Push to Talk
(Low)

S

croll/Weather

Mini-USB
Charging Port

MON

MENU

MT350

Line Drawing best fitting for UG

. Plug the AC power supply cord into the jack on the desk

2

stand.

. Plug the AC power supply into a standard wall outlet.

3

. With a radio facing forward, slide it into one of the charging

4

ockets.

p

. When charging in the battery charger, the red light on the

5

harger base will glow continuously.

c

Turning your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to

urn the radio off.

t

. In the ON position, the radio chirps and briefly shows all

1

eature icons available on the radio.

f

2. The display screen then shows the current channel, code
nd all features that are enabled.

a

Setting the Volume

Press and hold for three seconds, then rotate until you
reach a comfortable listening level.

1. Rotate clockwise to increase the volume.

. Rotate counterclockwise to decrease the volume.

2

Do not hold the radio close to your ear. If the volume is set to an

ncomfortable level, it could hurt your ear.

u

Talking and Listening

To communicate, all radios in your group must be set to the
same channel and Interference Eliminator Code.

1. To talk, press and hold .

2. When you are finished talking, release .

or maximum clarity, hold the radio two to three inches away

F

rom your mouth and speak directly into the microphone. Do not

f
cover the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet
apart.

Power Boost

To boost your radio’s power up to high power, press the top
portion of the button when talking. If you know your party is
close by, you can conserve your battery’s energy by pushing the
lower part of the button to use less power.

Note:

If you are on an FRS only channel (see Channels and
Frequencies table) the radio will only use low power when either
portion of the is pressed.

Monitor Button

Pressing and holding for three seconds allows you to listen
to the volume level of the radio when you are not receiving. This
allows you to adjust the volume, if necessary. You can also
press to check for activity on the current channel before you
talk.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the
radio emits a continuous warning tone and stops transmitting if
you press for 60 continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the
radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and all
other channels are GMRS. (See the "Channels and Frequencies"
table on overleaf for details.)

1. With the radio on, press . When the radio is on a 0.5

watt channel, displays. When the radio is on a 1.5 watts

channel, displays. The current channel flashes.

2. Press or and select an unused or quiet channel.

3. Press to save the channel setting or to continue set

up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by
blocking transmissions from unknown sources. Your radio has

121 Interference Eliminator Codes. Codes 1 – 38 are the
standard analog codes that appear on other FRS/GMRS radios.

odes 39 – 121 are additional digital codes added for superior

C

nterference protection. 0 is the off position, no analog or digital

i

odes are enabled.

c

o set the code for a channel:

T

. Press until the code starts to flash.

1

. Press or to select the code.

2

. Press to save the code setting or to continue set up.

3

ou can set a different code for each channel using this

Y

rocedure. An extended press of or allows you to scroll

p
through the Interference Code rapidly so you can quickly reach
the code you want.

Note: You must set the Interference Eliminator Code to 0 on a
radio that uses Interference Eliminator Codes to communicate

ith radios that do not have Interference Eliminator Codes.

w

elect 0 for “no tone, no code” and OFF will flash on your radio’s

S

isplay.

d

etting and Transmitting Call Tones

S

our radio can transmit different call tones to other radios in

Y

our group so you can alert them that you want to talk. Your

y
radio has 20 call tones from which to choose.

o set a call tone:

T

. Press three times until the current call tone setting

1

flashes and appears.

2. Press or to change and hear the call tone.

3. Press to set the new call tone or to continue set up.

To transmit your call tone to other radios set to the same

hannel and Interference Eliminator Code as your radio,

c

ress .

p

ote: Setting the call to 0 disables the call tone feature.

N

Hands-Free Use Without Accessories ( )

You can use the iVOX feature to transmit hands-free without the
need for any headset accessories. Once iVOX is turned on, the
radio detects your voice and transmits when you speak into the
internal microphone.

1. Press until appears on the display. The current
setting On/Off will flash.

2. Press or to select On or Off.

3. Press to set or to continue set up.

Hands-Free Use With Accessories ( )

You can transmit hands-free more reliably with the use of
optional headset accessories. Once VOX is turned on, the radio
detects your voice and transmits when you speak.

Many accessories (sold separately) are available for your radio.
For more information, visit our Web site at
motorolasolutions.com/talkabout.

1. Turn the radio off and plug the VOX accessory into the
accessory port.

2. Turn the radio on. VOX shows on the display.

3. Adjust the volume appropriately by rotating . Lower the
volume before placing the accessory on your head or in your
ear.

4. To turn off, simply remove accessory.

Note: There is a short delay between the time you start talking
and when the radio transmits. There is a short delay before the
transmission is completed.

Setting the Sensitivity Level When in Mode

Adjusting the radio’s sensitivity level helps minimize the
possibility of unintended noises triggering a transmission and
helps the radio pick up soft voices.

1. Press until VOX and the level setting (1 - 3) appear on
the display.

2. Press or to select the sensitivity level.

3. Press to set or to continue set up.

3 = High Sensitivity for quiet environments

2 = Medium Sensitivity for most environments

1 = Low Sensitivity for noisy environments

3

Note: When you connect a headset, the radio is automatically
set to the last chosen sensitivity level.

QTNoise Filtering

he Q

oise-filtering feature helps to ensure uninterrupted

T

n

T

communication with other Motorola radios that have this

eature. This feature also filters out unwanted transmissions

f

rom other radios. This is useful in places where there is

f
heavy radio traffic, such as amusement parks or ski resorts.

oise filtering is not available when the radio is

ote: Q

n

N

T

canning.

s

To turn Q

1

2

noise filtering on or off:

T

. Press until displays. The current setting On/Off will

lash.

f

. Press or to turn noise filtering On or Off.

3. Press to confirm your selection or to continue set
p.

u

To transmit to a radio that has Q

. Select the same channel and Interference Eliminator

1

noise filtering turned on:

T

Code as the other radio.

. Press to send a call tone. This allows your voice to

2

pass through the Q

noise filter on the receiving radio.

T

3. Press and speak normally.

ote: If you skip step 2, the beginning of your message may

N

not be heard on the receiving radio. For a 30-second period,

tarting after the last transmission, all transmissions

s
received on the selected channel and code will pass

hrough the Q

t

TM

ibraCall

V

VibraCall

eceiving a message. This is useful in noisy environments. When

r

he alert is on, the radio vibrates once every 30 seconds when

t
you receive a message on the channel and code you set.

1. To turn vibrating alerts on, press until is displayed. The

current setting will flash.

2. Press or to change the setting to On/Off.

3. Press to set or to continue set up.

Keypad Tones

You may enable or disable the speaker key tones. You will hear
the key tone each time a button is pushed.

1. Press until appears. The current setting On/Off will

2. Press either or to turn On or Off.

3. Press to confirm or to continue set up.

Note: When the key tone feature is off, the following are not
disabled:

• Transmit timeout alert tone

• Call tone

• Low battery alert tone or

• The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set your radio to transmit a unique tone when you finish
transmitting. It is like saying “Roger” or “Over” to let others
know you are finished talking.

1. With the radio on, press until the appears. The

2. Press or to turn On or Off.

3. Press to set or to quit menu mode.

Dual Watch Scan

This feature allows you to monitor two channels at the same
time.

1. Press the button until the Dual Channel Scan icon

2. Press the or buttons to select the second channel for

3. Press or the PTT button to confirm the channel selection.

When the Dual Watch feature is activated, the radio will switch
sequentially between the primary and the Dual Watch channels.

The active channel will display for five (5) seconds after any
activity has ended on the dual channel. You may talk on the Dual
Watch channel during this period.

lert

A

M

T

is a vibrating alert that notifies you that your radio is

flash.

current setting On/Off flashes.

displays.

Dual Watch reception. (if you want to disable the Dual
Watch function, set it to ‘OFF’).

oise filter.

n

T

MT Series

Special Features

mergency Alert Mode

E

The Emergency Alert feature can be used to signal members in

our group of your need for urgent help. MT series radios will

y

perate in an automatic “hands-free” emergency control mode

o
for a total of 30 seconds after activating the Emergency Alert. MT

eries radios in your group will automatically advance the

s
speaker volume to the maximum setting and sound a warbling

lert tone for 8 seconds. The alert tone is emitted from your own

a
radio speaker and the receiving radios in your group. After the 8

econd alert, any spoken words or incidental sounds at your end

s

ill be transmitted to the group for 22 seconds. For the 30 second

w
duration of Emergency Alert mode, MT series radio controls and

uttons will be locked to maximize reception of the emergency

b
message.

1. Press and hold the Emergency Alert button for 3 seconds.

. Release the button after the LED Indicator glows red and the

2

alert tone begins to sound. There is no need to continue to
hold the Emergency Alert button or use PTT for your message
to be transmitted.

3. After the alert tone ends you may speak into the
microphone. Your voice or incidental sounds will be

ransmitted. The LED indicator will continue to glow for the

t

uration of the 22 second period.

d

4. After 30 seconds your radio speaker will emit a Talk

onfirmation Tone and the LED Indicator will extinguish.

C

peration then returns to normal two-way mode.

O

ote: All Motorola Talkabout EM, MJ, MR, and MT series radios

N

are fully compatible with the Emergency Alert feature. Radios

ther than EM, MJ, MR, and MT series can receive the

o
emergency alert signal, but will not respond with adjusted volume

ettings, locked controls, or a warbling alert tone. Users of other

s
radio models set to the same channel and Interference Eliminator

ode will hear a steady tone for 8 seconds followed by the voice

C
transmission for 22 seconds.

arning: The Emergency Alert feature should only be used in

W

the event of an actual emergency. Motorola is not responsible if
there is no response to the emergency alert from the receiving
group.

Built-in Flashlight

Press and hold the flashlight button to turn and keep the light on.
The switch functions as a momentary control for the light.

Note: Turn off the flashlight when not in use to conserve battery
power.

Keypad Lock

To avoid accidentally changing your radio settings:

1. Press and hold until displays.

2. When in lock mode, you can turn the radio on and off, adjust
the volume, receive, transmit, send a call tone, and monitor
channels. All other functions are locked.

To unlock the radio, press and hold until is no longer
displayed.

Scanning Channels

Use scan to search the 22 channels for transmissions from
unknown parties, to find someone in your group who has
accidentally changed channels, or to quickly find unused
channels for your own use.

There is a priority feature and 2 modes of scanning ( basic and
advanced ) to make your search more effective. The basic scan
mode uses the channel and code combinations for each of the
22 channels as you have set them ( or with the default code
value of 1). The “Advanced Scan” mode will scan all channels
for any and all codes, detect any code in use, and use that code
value temporarily for that channel.

Priority is given to the “home channel,” that is, the channel (and
Interference Eliminator Code) your radio is set to when you start
the scan. This means the initial channel (and code setting) is
scanned more often than the other 21 channels, and your radio will
respond quickly to any activity occurring on the home channel as
a priority.

To start Scanning:

1. Briefly press the key. The scan will appear in the
display, and the radio will begin to scroll through the channel
and code combinations.

2. When the radio detects channel activity matching the
channel and code combination, it stops scrolling and you
can hear the transmission.

3. To respond and talk to the person transmitting, press
within five seconds after the end of the transmission.

4. The radio will resume scrolling through the channels five
seconds after the end of any received activity.

5. To stop scanning, briefly press the key.

o start Advanced Scanning:

T

. Set the Interference Eliminator Code to “zero” or OFF.

1

. Briefly press the key. The scan will appear in the

2

isplay, and the radio will begin to scroll through the

d

hannels. No Interference Eliminator Codes will filter what

c

s heard.

i

. When the radio detects channel activity with ANY code (or

3

O code), it stops scrolling and you can hear the

N
transmission. Any Interference Eliminator Code that may be
in use by that party will be detected and displayed.

4. To respond and talk to the person transmitting, press
within five seconds of the end of the transmission. The radio
will transmit using the newly detected Interference

liminator Code.

E

5. The radio will resume scrolling through the channels five
seconds after the end of any received activity.

6. To stop scanning, briefly press the key.

Scanning Notes:

1. If you press while the radio is scrolling through inactive

hannels, the transmission will be on the “home channel”.

c

canning will resume five seconds after the end of your

S

ransmission. You may press the key to stop scanning at

t
any time.

2. If the radio stops on an undesired transmission, you may

mmediately resume the scan by briefly pressing or .

i

3. If the radio repeatedly stops on an undesired transmission,
you may temporarily remove that channel from the scan list
by pressing and holding or for three seconds. You

ay remove more than one channel in this way.

m

4. To restore the removed channel(s) to the scan list, turn the
radio off and then back on, or exit and re-enter the scanning

ode by pressing .

m

5. You cannot remove the home channel from the scan list.

6. In Advanced Scan, the detected code will only be used for
one transmission. You must note the code, exit scan, and set
that detected code on that channel to permanently use the
detected code.

Weather Receiver

Your radio can tune in to broadcasts by the United States National
Oceanic and Atmospheric Administration (NOAA) Weather Radio
and Environment Canada Weatheradio.

You can listen to a weather channel (see “Weather Channels and
Frequencies” table below) or set your radio to alert you to
emergency weather broadcasts that interrupt routine broadcasts.
When you listen to a weather channel, you cannot use your radio in
scan mode or for two-way communications.

Both NOAA and Environment Canada have transmitters located
throughout the United States and Canada, respectively. These
transmitters broadcast watches, forecasts, and other information 24
hours a day.

Note: NOAA weather radio stations are assigned to cover specific
areas and service may be limited. Please check with your local
weather office for frequency and details, or visit
www.weather.gov/nwr in the US or
www.msc.ec.gc.ca/msb/weatheradio in Canada to view the
appropriate transmitter for your area.

The use of the NOAA logo does not provide an endorsement or
implied endorsement by NOAA’s National Weather Service, nor
does the use of the Weatheradio logo provide an endorsement or
implied endorsement by Environment Canada.

Turning Weather Channel Reception On and Off

1. To turn weather reception on, press and hold for 3
seconds.

2. To turn off, press or turn the radio off and then back on.

Setting the Weather Channel

Your radio receives weather frequencies:

1. After turning weather reception on, press . The current
channel flashes.

2. Press or to select the appropriate channel with good
reception in your area.

3. Press to save the weather channel setting.

Setting the Weather Alert

Your radio can be set to respond to NOAA Weather Radio
emergency messages. A special alarm tone sounds an alert and
turns on the weather receiver to give you immediate weather
and emergency information.

4

. After turning weather reception on, press twice. On/Off

1

isplays.

d

2. Press or to select On/Off. If you activate Weather

Alert and return to two-way mode, will display.

. Press to save the Weather Alert setting.

3

. Press to return to two-way mode.

4
As with two-way radio reception, weather channel reception

epends on how close you are to a transmitter and whether you

d
are indoors or outdoors. Because weather channels are

ransmitted without codes, they may contain static or noise.

t
Weather Alert will not function while actively transmitting or

eceiving in two-way mode.

r

canning for Weather Channel

S

he radio can scan for an active NOAA transmission

T

utomatically.

a

1. After turning weather reception on, briefly press the key.

2. The scan icon will appear in the display, and the channel
will scroll through the NOAA channels 1-7.

3. When the radio detects channel activity, it stops scanning
and you can hear the transmission.

. You may resume the scan by briefly pressing or .

4

. To stop scanning, briefly press the key. The scan

5

icon will disappear.

Weather Channels and Frequencies

eather

W
Channel

WX1 162.550 MHz WX7 162.525 MHz

WX2 162.400 MHz WX8 161.650 MHz

WX3 162.475 MHz WX9 161.775 MHz

WX4 162.425 MHz WX10 161.750 MHz

WX5 162.450 MHz WX11 162.000 MHz

WX6 162.500 MHz

requency

F

eather

W

Channel

requency

F

Channels and Frequencies

Channel

Frequency Description

462.5625

1

462.5875

2

462.6125

3

462.6375

4

462.6625

5

462.6875

6

462.7125

7

467.5625

8

467.5875

9

467.6125

10

467.6375

11

MHz

MHz

MHz

MHz

MHz

MHz

MHz

MHz

MHz

MHz

MHz

GMRS/FRS 12

GMRS/FRS 13

GMRS/FRS 14

GMRS/FRS 15

GMRS/FRS 16

GMRS/FRS 17

GMRS/FRS 18

Channel

FRS 19

FRS 20

FRS 21

FRS 22

Frequency Description

467.6625
MHz

467.6875
MHz

467.7125
MHz

462.5500
MHz

462.5750
MHz

462.6000
MHz

462.6250
MHz

462.6500
MHz

462.6750
MHz

462.7000
MHz

462.7250
MHz

FRS

FRS

FRS

GMRS

GMRS

GMRS

GMRS

GMRS

GMRS

GMRS

GMRS

MT Series

Warranty

onsumer Two-Way Radio Products and Accessories

C
purchased in the United States or Canada.

hat Does this Warranty Cover?

W

ubject to the exclusions contained below, Motorola

S

olutions, Inc. (“Motorola”) warrants the Motorola branded

S
consumer two-way radios that operate via Family Radio

ervice or General Mobile Radio Service (“Products”), the

S
Motorola branded or certified accessories sold for use with

hese Products (“Accessories”) to be free from defects in

t

aterials and workmanship under normal consumer usage

m
for the period(s) outlined below. This limited warranty is the

xclusive remedy of a consumer, and applies as follows to

e
new Products and Accessories and purchased by

onsumers in the United States or Canada, which are

c

ccompanied by this written warranty:

a

Who is covered?

his warranty extends only to the first consumer purchaser,

T

nd is not transferable.

a

What will MOTOROLA SOLUTIONS, INC. do?

otorola Solutions, Inc., at its option, will at no charge

M
repair, replace or refund the purchase price of any
Products or Accessories that do not conform to this

arranty. We may use functionally equivalent

w
reconditioned/ refurbished/ pre-owned or new Products or

ccessories.

A

How to Obtain Warranty Service or Other Information?

To obtain service or information, please call

USA and Canada Two-Way Radios

Contact customer service at

[e-mail]

www.motorolasolutions.com/talkabout

www.facebook.com/ MotorolaTalkaboutWalkieTalkies

For Accessories:

Please call the telephone number designated above for the
Product with which they are used.

You will receive instructions on how to ship the Products or
Accessories at your expense, to Motorola or a Motorola
Authorized Repair Center. To obtain service, you must
include: (a) a copy of your receipt, bill of sale or other
comparable proof of purchase; (b) a written description of
the problem; (c) the name of your service provider, if
applicable; (d) the name and location of the installation
facility (if applicable) and, most importantly; (e) your
address and telephone number.

1-800-448-6686

Please visit

Like us on Facebook

Products Covered

roducts and Accessories

P

as defined above, unless

therwise provided for

o

elow:

b

atteries whose fully

B

charged capacity falls

elow 80% of their rated

b

apacity and batteries that

c
leak

Products and Accessories

hat are repaired or

t

eplaced

r

What Other Limitations Are There?
Any Implied Warranties, Including Without Limitation

The implied warranties of merchantability and fitness for
a particular purpose, shall be limited to the duration of
this limited warranty, otherwise the repair, replacement,
or refund as provided under this express limited warranty
is the exclusive remedy of the consumers, and is provided
in lieu of all other warranties, express or implied. In no
event shall Motorola Solutions be liable, whether in
contract or tort (including negligence) for damages in
excess of the purchase price of the product or accessory,
or for any indirect, incidental, special or consequential
damages of any kind, or loss of revenue or profits, loss of
business, loss of information or other financial loss
arising out of or in connection with the ability or inability
to use the products or accessories to the full extent these
damages may be disclaimed by law.

Some states and jurisdictions do not allow the limitation
or exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the
above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights that vary from state to state or from one
jurisdiction to another.

Length of Coverage

ne (1) year from the date

O

f purchase by the first

o
consumer purchaser of

he product unless

t
otherwise provided for

elow.

b

he balance of the

T

riginal warranty or for

o
ninety (90) days from the

ate returned to the

d
consumer, whichever is

onger.

l

Exclusions From Warranty Coverage

eriodic maintenance, repair and

ormal Wear and Tear:

N

replacement of Products or Accessories due to normal

ear

w

nd tear.

a

buse & Misuse: D

A

improper operation, storage, misuse or abuse, accident

r neglect, such as physical damage (cracks, scratches,

o

tc.) to the surface of the Products and Accessories

e
resulting from misuse; (b) contact with liquid, water, rain,

xtreme humidity or heavy perspiration, sand, dirt or the

e
like, extreme heat, or food; (c) use of the Products or

ccessories for commercial purposes or subjecting the

A

roduct or Accessory to abnormal usage or conditions;

P
or (d) other acts which are not the fault of Motorola.

Use of Non-Motorola branded Products and

ccessories:Defects or damage that result from the use

A

f Non-Motorola branded or certified products,

o
accessories, software or other peripheral equipment.

Unauthorized Service or Modification:

damages resulting from service, testing, adjustment,

nstallation, maintenance, alteration, or modification in

i
any way by someone other than Motorola or its

uthorized service centers.

a

ltered Products:

A

numbers or date tags that have been removed, altered or

bliterated; (b) broken seals or that show evidence of

o
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or
parts.

Communication Services:

failure of Products or Accessories due to any
communication service or signal you may subscribe to or
use with the Products or Accessories.

P

efects or damage that result from: (a)

Defects or

roducts or Accessories with (a) serial

P

Defects, damages, or the

Patent and Copyright Information

Manufactured and distributed by Giant International Ltd.,
official licensee for this product. MOTOROLA, MOTOROLA
SOLUTIONS and the Stylized M Logo are trademarks or
registered trademarks of MotorolaTrademark Holdings, LLC
and are used under license. All other trademarks are the
property of their respective owners. ©2015 Motorola
Solutions, Inc. All rights reserved.

5

MT Series