Motorola 99FT4086 User Manual

MOTOTRBO XPR

Display Portable

User Guide

68009502001-A

7550

Contents

This User Guide contains all the information you need to use the MOTOTRBO XPR Series Digital Portable Radios.

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . 7

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Important Safety Information . . . . . . . . . . . . . . . . . 10

Product Safety and RF Exposure Compliance . . 10

Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Computer Software Copyrights . . . . . . . . . . . . . . . 11

Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . 12

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . 1

What Your Dealer/System Administrator

Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Preparing Your Radio for Use . . . . . . . . . . . . . . . . . 2

Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . 2

Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . 3

Contents

Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . 3

Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . 4

Attaching the Universal Connector Cover (Dust Cover)

Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . 5

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 6

Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . 6

Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . 8

Assignable Radio Functions . . . . . . . . . . . . . . . . . 8

Assignable Settings or Utility Functions . . . . . . . 10

Using the 4-Way Navigation Button . . . . . . . . . . . . 10

Accessing the Programmed Functions . . . . . . . . . 11

Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . 13

Switching Between Conventional Analog and Digital

Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Identifying Status Indicators . . . . . . . . . . . . . . . . . 15

Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Call Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Advanced Menu Icons . . . . . . . . . . . . . . . . . . . . . . 17

Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

English

Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Making and Receiving Calls . . . . . . . . . . . . . . . . . . 21

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Selecting a Radio Channel, Subscriber ID,

or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Receiving and Responding to a Radio Call . . . . . . 23

Receiving and Responding to a Group Call . . . . . 23

Receiving and Responding to a Private Call . . . 24

Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . 25

Receiving and Responding to a Selective Call . . 26

Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 27

Making a Call with the Channel Selector Knob . . 27

Making a Group Call . . . . . . . . . . . . . . . . . . . . . 27

Making a Private Call . . . . . . . . . . . . . . . . . . . . 28

Making an All Call . . . . . . . . . . . . . . . . . . . . . . . 29

Making a Selective Call . . . . . . . . . . . . . . . . . . 30

Making a Group or Private Call with the One Touch

Access Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Making a Group, Private or All Call with the

Programmable Number Key . . . . . . . . . . . . . . . . 32

Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . 33

Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 34

Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . 34

Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . . 35

Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . .36

Radio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Sending a Radio Check . . . . . . . . . . . . . . . . . . . . 37

Remote Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Initiating Remote Monitor . . . . . . . . . . . . . . . . . . . 38

Stopping Remote Monitor . . . . . . . . . . . . . . . . . . 40

Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Viewing an Entry in the Scan List . . . . . . . . . . . . 40

Viewing an Entry in the Scan List by Alias Search 41

Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . 41

Adding a New Entry to the Scan List . . . . . . . . 41

Deleting an Entry from the Scan List . . . . . . . . 42

Setting and Editing Priority for an Entry in the Scan

List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Starting and Stopping Scan . . . . . . . . . . . . . . . . . 45

Responding to a Transmission During a Scan . . 45

Deleting a Nuisance Channel . . . . . . . . . . . . . . . 46

Restoring a Nuisance Channel . . . . . . . . . . . . . . 46

Vote Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Contacts Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Making a Group Call from Contacts . . . . . . . . . . . 48

Making a Private Call from Contacts . . . . . . . . . 49

Making a Call by Alias Search . . . . . . . . . . . . . . 50

Contents

English

Assigning an Entry to a Programmable

Number Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Removing the Association between Entry and

Programmable Number Key . . . . . . . . . . . . . . . 52

Setting Default Contact . . . . . . . . . . . . . . . . . . . 53

Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . 53

Activating and Deactivating Call Ringers for Call Alert 53 Activating and Deactivating Call Ringers for Private

Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Activating and Deactivating Call Ringers for Selective

Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Activating and Deactivating Call Ringers for Text

Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Activating and Deactivating Call Ringers for

Telemetry Status with Text . . . . . . . . . . . . . . . . 55

Assigning Ring Styles . . . . . . . . . . . . . . . . . . . . 56

Escalating Alarm Tone Volume . . . . . . . . . . . . . . 56

Call Log Features . . . . . . . . . . . . . . . . . . . . . . . . . 57

Viewing Recent Calls . . . . . . . . . . . . . . . . . . . . . 57

Storing an Alias or ID from a Call List . . . . . . . . . 57

Deleting a Call from a Call List . . . . . . . . . . . . . . 58

Viewing Details from a Call List . . . . . . . . . . . . . 58

Contents

Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . 59

Receiving and Responding to a Call Alert . . . . . 59

Making a Call Alert from the Contacts List . . . . . 59

Making a Call Alert with the One Touch Access Button 60

Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 60

Receiving an Emergency Alarm . . . . . . . . . . . . . 61

Responding to an Emergency Alarm . . . . . . . . . 62

Sending an Emergency Alarm . . . . . . . . . . . . . . 63

Sending an Emergency Alarm with Call . . . . . . . 63

Sending an Emergency Alarm with Voice to Follow 64

Reinitiating an Emergency Mode . . . . . . . . . . . . 65

Exiting Emergency Mode . . . . . . . . . . . . . . . . . . 66

Text Message Features . . . . . . . . . . . . . . . . . . . . 67

Writing and Sending a Text Message . . . . . . . . . 67

Sending a Quick Text Message . . . . . . . . . . . . . 68

Sending a Quick Text Message with the One Touch

Access Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Accessing the Drafts Folder . . . . . . . . . . . . . . . . 69

Viewing a Saved Text Message . . . . . . . . . . . 70

Editing and Sending a Saved Text Message . . 70

Deleting a Saved Text Message from Drafts . . 71

Managing Fail-to-Send Text Messages . . . . . . . 71

Resending a Text Message . . . . . . . . . . . . . . . 71

Forwarding a Text Message . . . . . . . . . . . . . . 72

Editing a Text Message . . . . . . . . . . . . . . . . . . 72

English

Managing Sent Text Messages . . . . . . . . . . . . . . 73

Viewing a Sent Text Message . . . . . . . . . . . . . 74

Sending a Sent Text Message . . . . . . . . . . . . . 74

Deleting All Sent Text Messages from Sent Items

Receiving a Text Message . . . . . . . . . . . . . . . . . 76

Reading a Text Message . . . . . . . . . . . . . . . . . . . 76

Managing Received Text Messages . . . . . . . . . . 77

Viewing a Text Message from the Inbox . . . . . 77

Viewing a Telemetry Status Text Message from the

Inbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Replying to a Text Message from the Inbox . . . 78

Deleting a Text Message from the Inbox . . . . . 79

Deleting All Text Messages from the Inbox . . . 79

Analog Message Encode . . . . . . . . . . . . . . . . . . . . 80

Sending MDC Message Encode to Dispatcher . . 80 Sending 5-Tone Message Encode to Contact . . . 80

Analog Status Update . . . . . . . . . . . . . . . . . . . . . . 81

Sending Status Update to Predefined Contact . . 81

Viewing 5-Tone Status Details . . . . . . . . . . . . . . . 81

Editing 5-Tone Status Details . . . . . . . . . . . . . . . 81

Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Dual Tone Multi Frequency (DTMF) . . . . . . . . . . . . 84

IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Starting an Automatic Site Search . . . . . . . . . . . . 85

Stopping an Automatic Site Search . . . . . . . . . . . 86

Starting a Manual Site Search . . . . . . . . . . . . . . . 87

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Radio Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Radio Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Password Lock Features . . . . . . . . . . . . . . . . . . . . 90

Accessing the Radio from Password . . . . . . . . . . 90

Unlocking the Radio from Locked State . . . . . . . 90

Turning the Password Lock On or Off . . . . . . . . . 91

Changing the Password . . . . . . . . . . . . . . . . . . . . 92

Bluetooth Operation . . . . . . . . . . . . . . . . . . . . . . . . 93

Finding and Connecting to a Bluetooth Device . . 93

Disconnecting from a Bluetooth Device . . . . . . . . 94

Switching Audio Route . . . . . . . . . . . . . . . . . . . . . 95

Viewing Device Details . . . . . . . . . . . . . . . . . . . . 95

Editing Device Name . . . . . . . . . . . . . . . . . . . . . . 95

Notification List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Accessing the Notification List . . . . . . . . . . . . . . . 96

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Turning the Radio Tones/Alerts On or Off . . . . . . 96

Turning Keypad Tones On or Off . . . . . . . . . . . . . 97

Setting the Tone Alert Volume Offset Level . . . . 97

Turning the Talk Permit Tone On or Off . . . . . . . 98

Setting the Power Level . . . . . . . . . . . . . . . . . . . . 98

Contents

English

Changing the Display Mode . . . . . . . . . . . . . . . . 99

Adjusting the Display Brightness . . . . . . . . . . . . 99

Controlling the Display Backlight . . . . . . . . . . . 100

Setting the Squelch Level . . . . . . . . . . . . . . . . 100

Turning the Introduction Screen On or Off . . . . 101

Locking and Unlocking the Keypad . . . . . . . . . . 101

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Turning the LED Indicator On or Off . . . . . . . . . 102

Turning the Voice Operating Transmission (VOX)

Feature On or Off . . . . . . . . . . . . . . . . . . . . . . . 103

Turning the Option Board Feature(s) On or Off 104

Identifying Cable Type . . . . . . . . . . . . . . . . . . . 104

Voice Announcement . . . . . . . . . . . . . . . . . . . . 104

Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . 105

Menu Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Analog Mic AGC . . . . . . . . . . . . . . . . . . . . . . . . 106

Digital Mic AGC . . . . . . . . . . . . . . . . . . . . . . . . . 106

Intelligent Audio . . . . . . . . . . . . . . . . . . . . . . . . 107

GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Accessing General Radio Information . . . . . . . 108

Accessing the Battery Information . . . . . . . . . 108

Checking the Radio Alias and ID . . . . . . . . . 108

Contents

Checking the Firmware Version and Codeplug Ver-

sion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Checking the GPS Information . . . . . . . . . . . 109

Front Panel Programming (FPP) . . . . . . . . . . . . . 110

Entering FPP Mode . . . . . . . . . . . . . . . . . . . . . . 110

Editing FPP Mode Parameters . . . . . . . . . . . . . 110

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Headsets and Headset Accessories . . . . . . . . . . 112

Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . 112

Remote Speaker Microphones . . . . . . . . . . . . . . . 112

Surveillance Accessories . . . . . . . . . . . . . . . . . . . 112

Miscellaneous Accessories . . . . . . . . . . . . . . . . . 113

Batteries and Chargers Warranty . . . . . . . . . . . . 114

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

English

Declaration of Conformity

This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.

DECLARATION OF CONFORMITY

Per FCC CFR 47 Part 2 Section 2.1077(a)

Responsible Party Name: Motorola Solutions, Inc.

Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744

Hereby declares that the product:

Model Name: XPR 7550

conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)

Class B Digital Device

As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Declaration of Conformity

English

Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

English

Notes

English

Important Safety Information

Software Version

Product Safety and RF Exposure Compliance

Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.

ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.

Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits.

For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website:

http://www.motorolasolutions.com/governmentandenterprise

Important Safety Information

All the features described in the following sections are

supported by the radio's software version R02.00.00. See Checking the Firmware Version and Codeplug

Version on page 109 to determine your radio's software

version.

Check with your dealer or system administrator for more details of all the features supported.

English

Computer Software Copyrights

The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product.

The AMBE+2 this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc.

This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form.

U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.

voice coding Technology embodied in

Computer Software Copyrights

English

Handling Precautions

The MOTOTRBO Series Digital Portable radio meets IP57 specifications, allowing the radio to withstand adverse field conditions such as being submersed in water.

• If the radio has been submersed in water, shake the

radio well to remove any water that may be trapped inside the speaker grille and microphone port. Trapped water could cause decreased audio performance.

• If the radio’s battery contact area has been exposed to

water, clean and dry battery contacts on both the radio and the battery before attaching the battery to the radio. The residual water could short-circuit the radio.

• If the radio has been submersed in a corrosive

substance (e.g. saltwater), rinse the radio and battery in fresh water then dry the radio and battery.

• To clean the exterior surfaces of the radio, use a diluted

solution of mild dishwashing detergent and fresh water (i.e. one teaspoon of detergent to one gallon of water).

Handling Precautions

• Never poke the vent (hole) located on the radio chassis

below the battery contact. This vent allows for pressure equalization in the radio. Doing so may create a leak path into the radio and the radio’s submersibility may be lost.

• Never obstruct or cover the vent, even with a label.

• Ensure that no oily substances come in contact with the

vent.

• The radio with antenna attached properly is designed to

be submersible to a maximum depth of 1 meter (3.28 feet) and a maximum submersion time of 30 minutes. Exceeding either maximum limit or use without antenna may result in damage to the radio.

• When cleaning the radio, do not use a high pressure jet

spray on the radio as this will exceed the 1 meter depth pressure and may cause water to leak into the radio.

Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Radio maintenance should only be done in service depot that is equipped to test and replace the seal on the radio.

English

Notes

English

Notes

English

Getting Started

Take a moment to review the following:

How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1

What Your Dealer/System Administrator

Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1

How to Use This Guide

For features that are available in both conventional Analog and Digital modes, no icon is shown.

Selected features are also available on the single-site trunking mode, Capacity Plus. See Capacity Plus on page 14 for more

information.

What Your Dealer/System Administrator

Can Tell You

Getting Started

This User Guide covers the basic operation of the MOTOTRBO Portables.

However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information.

Throughout this publication, the icons below are used to indicate features supported in either the conventional Analog mode or conventional Digital mode:

Indicates a conventional Analog Mode-Only feature.

Indicates a conventional Digital Mode-Only feature.

You can consult your dealer or system administrator about the following:

• Is your radio programmed with any preset conventional

channels?

• Which buttons have been programmed to access other

features?

• What optional accessories may suit your needs?

English

Preparing Your Radio for Use

Assemble your radio by following these steps:

Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2

Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Attaching the Belt Clip. . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Attaching the Universal Connector

Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . . page 5

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . page 6

Preparing Your Radio for Use

Charging the Battery

Your radio is powered by a Nickel Metal-Hydride (NiMH) or Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger

exactly as described in the charger user guide.

Charge a new battery 14 to 16 hours before initial use for best performance.

IMPORTANT: ALWAYS charge your IMPRES battery with an

IMPRES charger for optimized battery life and valuable battery data. IMPRES batteries charged exclusively with IMPRES chargers receive a 6-month capacity warranty extension over the standard Motorola Premium battery warranty duration.

English

Attaching the Battery

Attaching the Antenna

Align the battery with the rails on the back of the radio. Press

the battery firmly, and slide upward until the latch snaps into

place. Slide battery latch into lock position.

To remove the battery, turn the radio off. Move the battery latch into unlock position and hold, and slide the battery down and off the rails.

Battery Latch

With the radio turned off, set the antenna in its receptacle and turn clockwise.

To remove the antenna, turn the antenna counterclockwise.

If antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio. See Antennas on page 111 for a list of available antennas.

Preparing Your Radio for Use

English

Attaching the Belt Clip

Attaching the Universal Connector Cover

(Dust Cover)

Align the grooves on the clip with those on the battery and press downward until you hear a click.

To remove the clip, press the belt clip tab away from the battery. Using a key may be helpful. Then slide the clip upward and away from the radio.

Preparing Your Radio for Use

The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio.

Insert the hooked end of the cover into the slots above the universal connector. Press downward on the

Universal Connector

connector cover, press down on the cover and turn the thumbscrew counterclockwise. Lift the cover up, slide the connector cover loop upwards, and remove it from the attached antenna.

Replace the dust cover when the universal connector is not in use.

cover to seat the lower tab properly into the RF connector.

Turn the thumbscrew clockwise to secure the connector cover to the radio.

To remove the universal

English

Powering Up the Radio

Rotate the On/Off/Volume

Control Knob clockwise

until you hear a click. You

see MOTOTRBO (TM) on the

radio’s display momentarily,

followed by a welcome

message or welcome

image.

The LED lights up solid

green and the Home screen

lights up if the backlight

setting is set to turn on

automatically.

LED

NOTE: The Home screen does not light up during a power up if

the LED indicator is disabled (see Turning the LED Indicator On or Off on page 102).

A brief tone sounds, indicating that the power up test is successful.

NOTE: There is no power up tone if the radio tones/alerts

function is disabled (see Turning the Radio Tones/ Alerts On or Off on page 96).

If your radio does not power up, check your battery. Make sure that it is charged and properly attached. If your radio still does not power up, contact your dealer.

To turn off the radio, rotate this knob counterclockwise until you hear a click. You see a brief display.

Powering Down

on the radio’s

Preparing Your Radio for Use

English

Adjusting the Volume

To increase the volume,

turn the On/Off/Volume Control Knob clockwise.

To decrease the volume, turn this knob counterclockwise.

NOTE: Your radio can be

programmed to have a minimum volume offset where the volume level cannot be turned down fully. Check with your dealer or system administrator for more information.

Identifying Radio Controls

Take a moment to review the following:

Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7

Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 8

Using the 4-Way Navigation Button. . . . . . . . . . . . . . . page 10

Accessing the Programmed Functions . . . . . . . . . . . . page 11

Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12

Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 13

Switching Between Conventional Analog and

Digital Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14

Capacity Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14

English

Radio Controls

1 2

4 5

6 7

8 9

Channel Selector Knob

On/Off/Volume Control Knob

LED Indicator

18 17

16 15

13 12

Side Button 1*

Push-to-Talk (PTT) Button

Side Button 2*

Side Button 3*

Front Button P1*

Menu/OK Button

4-Way Navigation Button

Keypad

Back/Home Button

Front Button P2*

Display

Microphone

Speaker

Universal Connector for Accessories

Emergency Button*

Antenna

* These buttons are programmable.

Identifying Radio Controls

English

Programmable Buttons



Assignable Radio Functions

Your dealer can program the programmable buttons as

shortcuts to radio functions or preset channels/groups

depending on the duration of a button press:

• Short press – Pressing and releasing rapidly.

• Long press – Pressing and holding for the programmed

duration.

• Hold down – Keeping the button pressed.

NOTE: The programmed duration of a button press is

applicable for all assignable radio/utility functions or

settings. See Emergency Operation on page 60 for

more information on the programmed duration of the

Emergency button.

Identifying Radio Controls

Bluetooth Audio Switch – Toggles audio routing between

internal radio speaker and external Bluetooth-enabled accessory.

Contacts – Provides direct access to the contacts list. Call Alert – Direct access to the radio contacts list to select a

radio contact to send a call alert to.

Call Forwarding – Toggles Call Forwarding on or off. Call Log – Selects the call log list. Voice Announcement for Channel – Plays zone and channel

announcement voice messages for the current channel. This function is unavailable when Voice Announcement is disabled.

Emergency – Depending on the programming, initiates or

cancels an emergency alarm or call.

Intelligent Audio On/Off – Toggles Intelligent Audio on or off. Manual Dial – Initiates a call by keying in any subscriber

ID.

Manual Site Roam* – Starts the manual site search. Mic AGC On/Off – Toggles the internal microphone automatic

gain control (AGC) on or off. Not applicable during a Bluetooth session.

English

* Not applicable in Capacity Plus

Monitor – Monitors a selected channel for activity.

Nuisance Channel Delete* – Temporarily removes an

unwanted channel, except for the Selected Channel, from the

scan list. The Selected Channel refers to the user’s selected

zone/channel combination from which scan is initiated.

One Touch Access – Directly initiates a predefined Private or

Group Call, a Call Alert or a Quick Text message.

Repeater/Talkaround* – Toggles between using a repeater

and communicating directly with another radio.

Identifying Radio Controls

Scan* – Toggles scan on or off. Site Lock On/Off* – Toggles the automatic site roam on or

off.

Status – Selects the status list menu.

Option Board Feature – Toggles option board feature(s) on or

off for option board-enabled channels.

Permanent Monitor* – Monitors a selected channel for all radio

traffic until function is disabled.

Privacy – Toggles privacy on or off.

Radio Alias and ID – Provides radio alias and ID.

Radio Check – Determines if a radio is active in a system.

Radio Enable – Allows a target radio to be remotely

enabled.

Radio Disable – Allows a target radio to be remotely

disabled.

Remote Monitor – Turns on the microphone of a target

radio without it giving any indicators.

Telemetry Control – Controls the Output Pin on a local or

remote radio.

Text Message – Transmit Interrupt Remote Dekey – Stops the

transmission of a remote monitored radio without giving any indicators, or an ongoing interruptible call to free the channel.

V o ice Ann ou ncement On/O ff – Toggles Voice Announcement on or off.

V o ice Op eratin g Transmission (VOX) – Toggles VOX on or

off.

Zone – Allows selection from a list of zones.

Selects the text message menu.

* Not applicable in Capacity Plus

English

Assignable Settings or Utility Functions



Using the 4-Way Navigation Button

All Tones/Alerts – Toggles all tones and alerts on or off. Backlight On/Off – Toggles display backlight on or off. Backlight Brightness – Adjusts the brightness level. Display Mode – Toggles the day/night display mode on or off. Keypad Lock – Toggles keypad between locked and unlocked. Power Level – Toggles transmit power level between high and

low.

Squelch – Toggles squelch level between tight and

normal.

Identifying Radio Controls

You can use the 4-way navigation button, e, to scroll through

options, increase/decrease values, and navigate vertically.

Accessing the Programmed Functions

You can access various radio functions through one of the

following ways:

• A short or long press of the

relevant programmable buttons.

• Use the 4-way navigation button as follows:

1 To access the menu, press the c button. Press the

appropriate direction of the functions.

2 To select a function or enter a sub-menu, press the c

button.

3 To go back one menu level, or to return to the previous

screen, press the return to the Home screen.

NOTE: Your radio automatically exits the menu after a period

of inactivity and returns to your Home screen.

d button. Long press the d button to

ced

e to access the menu

Identifying Radio Controls

English

Using the Keypad

You can use the 3 x 4 alphanumeric keypad to access your radio’s features. You can use the keypad to enter subscriber aliases or IDs, and text messages. Many characters require that you press a key multiple times. The table below shows the number of times a key needs to be pressed to generate the required character.

Number of Times Key is Pressed

Key1 2345678910111213

1 2 3 4 5 6 7 8 9 0

Identifying Radio Controls

* #

1.,?!@&‘%-:*#

ABC2

DEF3

GHI4

JKL5

MNO6

PQRS7

TUV8

WXYZ9

* or del

# or space

NOTE: Press to enter “0” and long press to activate the CAPS lock. Another long press to turn off the CAPS lock. NOTE: Press during text entry to delete the character. Press during numeric entry to enter a “*”. NOTE: Press during text entry to insert a space. Press during numeric entry to enter a “#”.

English

Push-To-Talk (PTT) Button

The PTT button on the side of the radio serves two basic

purposes:

If the Talk Permi t Tone (see Turning the Talk Permit Tone On or Off on page 98) or the PTT Sidetone is enabled, wait

until the short alert tone ends before talking.

During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you

will hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond.

Identifying Radio Controls

PTT Button

• While a call is in progress, the PTT button allows the radio to

transmit to other radios in the call.

Press and hold down PTT button to talk. Release the PTT

button to listen.

The microphone is activated when the PTT button is pressed.

• While a call is not in progress, the PTT button is used to make

a new call (see Making a Radio Call on page 27).

You will also hear the Channel Free Indication tone if your call is interrupted, for example when the radio receives an

Emergency Call. You can turn off the Channel Free Indication tone or the PTT Sidetone by disabling all radio tones and alerts

(see Turning the Radio Tones/Alerts On or Off on page 96).

English

Switching Between Conventional Analog

and Digital Mode

Each channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Selector Knob to switch between an analog or a digital channel.

Channel Selector Knob

When switching from digital to analog mode, certain features are unavailable. Icons for the digital features (such as Messages) reflect this change by appearing ‘grayed out’. Disabled features are hidden in the menu.

Your radio also has features available in both analog and digital mode. However, the minor differences in the way each feature

works does NOT affect the performance of your radio.

NOTE: Your radio also switches between digital and analog

Identifying Radio Controls

modes during a dual mode scan (see Scan on

page 44).

Capacity Plus

Capacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which uses a pool of channels to support hundreds of users and up to 254 Groups. This feature allows your radio to efficiently utilize the available number of programmed channels while in Repeater Mode.

You can only access channel(s) with Capacity Plus via the

Channel Selector Knob, while features supported in Capacity Plus can be accessed via the menu and/or a programmable button press.

Icons of features not applicable to Capacity Plus will not be available in the menu. You will hear a negative indicator tone if you access a feature not applicable to Capacity Plus via a programmable button press.

Your radio also has features that are available in both conventional digital mode and Capacity Plus. However, the

minor differences in the way each feature works does NOT

affect the performance of your radio.

Check with your dealer or system administrator for more information on this system.

English

Identifying Status Indicators

Your radio indicates its operational status through the following:

Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15

Call Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17

Advanced Menu Icons. . . . . . . . . . . . . . . . . . . . . . . . . page 17

Mini Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18

Sent Item Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18

LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19

Audio Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20

Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20

Display Icons

The 132 x 90 pixels, 256 colors, liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries.

The following are icons that appear on the status bar at the top of the radio’s display. Icons are displayed on the status bar, arranged left-to-right, in order of appearance/usage.

Received Signal Strength Indicator (RSSI)

The number of bars displayed represents the radio signal strength. Four bars indicate the strongest signal. This icon is only displayed while receiving.

Battery

The number of bars (0 – 4) shown indicates the charge remaining in the battery.

Blinks when the battery is low.

Bluetooth

The Bluetooth feature is enabled but there is no remote Bluetooth device connected.

Bluetooth Connected

The Bluetooth feature is enabled. The icon stays lit when one or more remote Bluetooth devices are connected.

Emergency

Radio is in Emergency mode.

Identifying Status Indicators

English

Notification

Notification list is not empty.

Scan

Scan feature is enabled.

Scan – Priority 1*

Radio detects activity on channel/group designated as Priority 1).

Scan – Priority 2 *

Radio detects activity on channel/group designated as Priority 2.

Vote Scan

Vote scan feature is enabled.

Monitor

Selected channel is being monitored.

Talkaround

In the absence of a repeater, radio is currently configured for direct radio to radio communication.

Site Roaming*

The site roaming feature is enabled.

Secure

Identifying Status Indicators

The Privacy feature is enabled.

Unsecure

The Privacy feature is disabled.

GPS Available

The GPS feature is enabled. The icon stays lit when a position fix is available.

GPS Not Available/Out of Range

The GPS feature is enabled but is not receiving data from the satellite.

Option Board

The Option Board is enabled.

Option Board Non-Function

The Option Board is disabled.

Ton es Disable

Tones are turned off.

Power Level

Radio is set at Low power.

Radio is set at High power.

Not applicable in Capacity Plus

English

* Not applicable in Capacity Plus

+ 110 hidden pages