Motorola 89FT7023 Users manual
User’s Guide
00
WDE1000
CardBus Adaptor
WDE1100
Mini PCI Card
6802978C75-B
WDE1000
WDE11
6802978C75-B
@6802978C75@
April 2006
Disclaimer
Statements included in this manual indicating support provided by Motorola are subject to changes at any time.
Motorola reserves the right to make changes to this manual.
Declaration of Conformity
Per FCC CFR 47 Part 2 Section 2.1077(a)
• Consult the dealer or an experienced radio/TV techni-
cian for help.
As a personal computer peripheral, this device complies
with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC ID: AZ489FT7016 refers to WDE1000
FCC ID: AZ489FT7023 refers to WDE1100
Responsible Party Name: Motorola, Inc.
Address: 1301 East Algonquin Road Schaumburg,
IL 60196
USA Phone Number: 1-800-221-7144
Hereby declares that the product:
Product Name:WDE1000/WDE1100
Model Number: F2889A/F2892A
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d)
and section 15.109(a)
Class B Digital Device
This equipment has been tested
and found to comply with the
NOTE
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
limits for a Class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in a
residential installation. This
equipment generates, uses and
can radiate radio frequency
energy and, if not installed and
used in accordance with the
instructions, may cause harmful
interference to radio
communications. However, there
is no guarantee that interference
will not occur in a particular
installation.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
NOTE
WDE1100 only.
WDE1100 is an OEM module and
is intended only for OEM integrators under the following conditions:
1. The antenna should be
installed so there is at least
20cm of separation between
the body of the user and
nearby persons and the
antenna.
2. The OEM Module may not be
co-located with any other
transmitter or antenna.
3. The antenna installation of
this OEM Module, including
antenna gain, must satisfy the
requirements as specified in
FCC ID: AZ489FT7023 grant of
equipment authorization.
As long as the above conditions
are met, further transmitter tests
will not be required.
However, the OEM integrator is
still responsible for testing their
end product for any additional
compliance requirements re quired
with this Module installed.
If the above conditions can not be
met then the FCC authorization is
no longer considered valid and
the FCC ID can not be used on the
final product.
In this case, the OEM Integrator
will be responsible for reevaluation the end product,
including the transmitter, and
obtaining a separat e FCC
authorization.
ii
Regulatory Requirements
The Federal Communications Commission (FCC) requires
application for certification of digital devices in accordance
with CFR Title 47, Part 15 and Part 90. This includes Electromagnetic Energy Exposure (EME) testing. As the
WDE1000/1100 is not a stand-alone modem but is a PC
card, the WDE1000/1100 cannot be tested by itself for
EME certification and was tested while inserted in a laptop
computer.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
The WDE1000/1100 transmitters, 802.11a@4.9GHz and
802.11b/g@2.4GHz will not work simultaneously when
used in the present configuration.
NOTE
WDE1000 only
The WDE1000 was approved by
the United States Federal Communications Commission (FCC) for
use with internal on board
antennas.
For external antenna use in the
United States, th e Federal
Communications Commission
(FCC) requires that an approval
will be obtained.
.
Safety and General Information
IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION.
READ THIS INFORMATION BEFORE USING YOUR
MOTOROLA WDE1000/1100.
RF Operational Characteristics
Your Motorola product contains a radio frequency transmitter to convey the information you wish to send as well as
occasional automatic signals used to sustain connection to
the wireless network, and a receiver which enables you to
receive communication and connection information from
the network.
Antenna Care (WDE1000 only)
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments
could damage the radio product and may violate FCC regulations. When using any approved accessory antenna, position it at least eight inches (20 cm) from any part of any
person.
DO NOT hold the antenna when the radio product is "IN
USE". Holding the antenna affects communication quality
and may cause the product to operate at a higher power
level than needed.
Compliance and Control Guidelines and Operating
Instructions for WDE1100 Installed as Fixed Site
If WDE1100 is installed at a fixed location and operated as
a fixed unit, the antenna installation must comply with the
following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in
the standards and guidelines listed in “Product Operation
and EME Exposure” on page iii:
• The antenna should be mounted outside the building on
the roof or a tower if at all possible.
• As with all fixed site antenna installations, it is the
responsibility of the licensee to manage the site in
accordance with applicable regulatory requirements
and may require additional compliance actions such as
site survey measurements, signage, and site access
restrictions in order to ensure that exposure limits are
not exceeded.
Product Operation and EME Exposure
Your Motorola product is designed to comply with the following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
• United States Federal Communications Commission,
Code of Federal Regulations; 47 CFR part 2 sub-part J.
• American National Standards Institute (ANSI) / Insti-
tute of Electrical and Electronics Engineers (IEEE).
C95. 1-1992.
• Institute of Electrical and Electronics Engineers
(IEEE). C95. 1-1999 Edition.
• International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
• Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radiofrequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
• Australian Communications Authority Radiocommu-
nications (Electromagnetic Radiation - Human Exposure) Standard 2003.
• ANATEL, Brasil Regulatory Authority, Resolution
303 (July 2, 2002) "Regulation of the limitation of
exposure to electrical, magnetic, and electromagnetic
fields in the radio frequency range between 9 kHz and
300 GHz." "Attachment to Resolution 303 from July 2,
2002."
The WDE1000 has been tested for compliance with FCC
RF exposure limits in laptop computer configurations with
side PCMCIA slots, and can be used in laptop computers
with substantially similar physical dimensions, construction, and electrical and RF characteristics.
iii
FCC ID: AZ489FT7016 MEET THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO
RADIO WAVES.
Your WDE1000 is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines
and establish permitted levels of RF energy for the general
population. The guidelines are based on standards that were
developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and
health.
The exposure standard for WDE1000 employs a unit of
measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6W/kg.
(1)
Tests
for SAR are conducted using standard operating positions
reviewed by the FCC with the WDE1000 transmitting at its
highest certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the WDE1000 while
operating can be well below the maximum value. This is
because the WDE1000 is designed to operate at multiple
power levels so as to use only the power required to reach
the network.
Before a WDE1000 model is available for sale to the public, it must be tested and certified to the FCC that it does not
exceed the limit established by the government-adopted
requirement for safe exposure. The tests are performed in
positions and locations as required by the FCC for each
model.
The FCC has granted an Equipment Authorization for this
WDE1000 with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR
information on this WDE1000 is on file with the FCC and
can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on FCC ID:
AZ489FT7016.
(1) In the United States and Canada, the SAR limit for
modems used by the public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for
the public and to account for any variations in measurements.
FCC ID: AZ489FT7023 MEET THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO
RADIO WAVES.
Your WDE1100 is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines
and establish permitted levels of RF energy for the general
population. The guidelines are based on standards that were
developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and
health.
After integration, this device uses electromagnetic energy
in the RF spectrum to provide communications between
two or more users over a distance. It uses radio frequency
energy or radio waves to send and receive information. The
integrated radio generates measurable RF energy only
while it is transmitting (during talking or sending data), not
when it is receiving (listening or receiving data) or in
standby mode.
Before a WDE1100 model is available for sale to the public, it must be tested and certified to the FCC that it does not
exceed the limit established by the government-adopted
requirement for safe exposure. The tests are performed in
positions and locations as required by the FCC for each
model.
The FCC has granted an Equipment Authorization for this
WDE1100 with all reported MPE as in compliance with the
FCC RF exposure guidelines. MPE information on this
WDE1100 is on file with the FCC and can be found under
the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on FCC ID:
AZ489FT7023.
Electro Magnetic Interference/Compatibility
Nearly every electronic device is
susceptible to electromagnetic
NOTE
interference (EMI) if
inadequately shielded, designed
or otherwise configured for
electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility
conflicts, turn off your WDE1000/1100 in any facility
where posted notices instruct you to do so. Hospitals or
health care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your WDE1000/1100
when on board an aircraft. Any use of a WDE1000/1100
must be in accordance with applicable regulations per airline crew instructions.
Medical Devices
Pacemakers
The Advanced Medical Technology Association
(AdvaMed) recommends that a minimum separation of 8
iv
inches (20 cm) be maintained between a WDE1000/1100
W
G
W
G
C
n
and a pacemaker. These recommendations are consistent
with those of the U.S. Food and Drug Administration.
Persons with pacemakers should:
• ALWAYS keep the WDE1000/1100 more than 8
inches (20 cm) from their pacemaker when the
WDE1000/1100 is turned ON.
• Turn the WDE1000/1100 OFF immediately if you
have any reason to suspect that interference is taking
place.
Hearing Aids
Some digital wireless modem products may interfere with
some hearing aids. In the event of such interference, you
may want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the
manufacturer of your device to determine if it is adequately
shielded from RF energy. Your physician may be able to
assist you in obtaining this information.
Operational Warnings
For Vehicle With Air Bags:
Do not place a WDE1000/1100 in the area over an
!
!
air bag or in the air bag deployment area. Air bags
A R N I N
inflate with great force. If a WDE1000/1100 is placed
in the air bag deployment area and the air bag
inflates, the WDE1000/1100 may be propelled with
great force and cause serious injury to occupants
of the vehicle.
Potentially Explosive Atmospheres
Turn off your WDE1000/1100 prior to entering any
area with a potentially explosive atmosphere.
unless it is a modem product type type especially
qualified for use in such areas as “Intrinsically
Safe” (for example, Factory Mutual, or CSA).
Sparks in a potentially explosive atmosphere can
cause an explosion or fire resulting in bodily injury
or even death.
The areas with potentially explosive atmospheres
referred to above include fueling areas such as
!
!
below decks on boats, fuel or chemical transfer or
A R N I N
storage facilities, and areas where the air contains
chemicals or particles such as grain, dust or metal
powders, and any other area where you would
normally be advised to turn off your vehicle engine.
Areas with potentially explosive atmospheres are
often but not always posted.
Blasting Caps and Blasting Areas
To avoid possible interference with blasting
operations, turn off your WDE1000/1100 when you
are near electrical blasting caps, in a blasting area,
or in areas posted: "Turn off two-way radio." Obey
all signs and instructions.
Operational Cautions
!
a u t i o
Cleaning and Drying Considerations
This product is not water proof, and exposing the unit to
liquids may result in permanent damage to the unit.
If your WDE1000/1100 interior gets wet, then do not try to
accelerate drying with the use of an oven or a dryer as this
will damage the WDE1000/1100 and void the warranty.
Instead, do the following:
1. Immediately power off the WDE1 0 00/1100.
2. Shake excess liquid from WDE1000/1100.
3. Place the WDE1000/1100 in an area that is at room
temperature and has good air flow.
4. Let the WDE1000/1100 dry for 72 hours before power-
ing on again.
If the WDE1000/1100 does not work after following the
steps listed above, contact your dealer for servicing information.
Clean the external surfaces of the WDE1000/1100 with a
damp cloth, using a mild solution of dishwashing detergent
and water. Some household c leaners may contain chemicals
that could seriously damage the WDE1000/1100. Avoid the
use of any petroleum-based solvent cleaners. Also, avoid
applying liquids directly on the WDE1000/1100.
Warranty Information
If the affected product is being purchased pursuant to a
written Communications System Agreement signed by
Motorola, the warranty contained in that written agreement
will apply. Otherwise, the following warranty applies.
What This Warranty Covers And For How Long
Motorola Inc. or, if applicable, Motorola Canada Limited
("Motorola") warrants the Motorola manufactured Broadband Data communications product, against material
defects in material and workmanship under normal use and
service for a period of One (1) Year from the date of shipment.
Motorola, at its option, will at no charge either repair the
Product (with new or reconditioned parts), replace it with
the same or equivalent Product (using new or reconditioned
Product), or refund the purchase price of the Product during
the warranty period provided purchaser notifies Motorola
according to the terms of this warranty. Repaired or
replaced Product is warranted for the balance of the original
applicable warranty period. All replaced parts of the Product shall become the property of Motorola.
v
This express limited warranty is extended by Motorola to
the original end user purchaser purchasing the Product for
purposes of leasing or for commercial, industrial, or governmental use only, and is not assignable or transferable to
any other party. This is the complete warranty for the Product manufactured by Motorola. Motorola assumes no obligations or liability for additions or modifications to this
warranty unless made in writing and signed by an officer of
Motorola. Unless made in a separate written agreement
between Motorola and the original end user purchaser,
Motorola does not warrant the installation, maintenance or
service of the Product.
Motorola cannot be responsible in any way for any ancillary equipment not furnished by Motorola which is attached
to or used in connection with the Product, or for operation
of the Product with any ancillary equipment, and all such
equipment is expressly excluded from this warranty.
Because each system which may use the Product is unique,
Motorola disclaims liability for range, coverage, or operation of the system as a whole under this warranty.
General Provisions
This warranty sets forth the full extent of Motorola's
responsibilities regarding the Product. Repair, replacement
or refund of the purchase price, at Motorola's option, is the
exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU
OF ALL OTHER EXPRESS WARRANTIES. MOTOROLA DISCLAIMS ALL OTHER WARRANTIES OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING
THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MOTOROLA
BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS
OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR
OTHER INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE SUCH PRODUCT, TO THE
FULL EXTENT SUCH MAY BE DISCLAIMED BY
LAW.
How To Get Warranty Service?
Purchaser must notify Motorola's representative or call
Motorola's Customer Response Center at 1-800-247-2346
within the applicable warranty period for information
regarding warranty service.
What Is Not Covered By The Warranty
1. Defects or damage resulting from use of the Product in
other than its normal and customary manner.
2. Defects or damage from misuse, accident, water, or
neglect.
3. Defects or damage from improper testing, operation,
maintenance, installation, alteration, modification, or
adjustment.
4. Breakage or damage to antennas unless caused directly
by defects in material workmanship.
5. A Product subjected to unauthorized Product modifica-
tions, disassemblies or repairs (including, without limitation, the addition to the Product of non-Motorola
supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal
warranty inspection and testing of the Product to verify
any warranty claim.
6. Product which has had the serial number removed or
made illegible.
7. Batteries (they carry their own separate limited war-
ranty).
8. Freight costs to the repair depot.
9. A Product which, due to illegal or unauthorized altera-
tion of the software/firmware in the Product, does not
function in accordance with Motorola's published specifications or with the FCC type acceptance labeling in
effect for the Product at the time the Product was initially distributed from Motorola.
10. Scratches or other cosmetic damage to Product sur-
faces that does not affect the operation of the Product.
11. That the software in the Product will meet the pur-
chaser's requirements or that the operation of the software will be uninterrupted or error-free.
12. Normal and customary wear and tear.
13. Non-Motorola manufactured equipment unless bearing
a Motorola Part Number in the form of an alpha
numeric number (i.e., TDE6030B).
14. Lift trucks for installation, removal, replacement or
repair of the Motorola supplied products from light,
power, telephone poles etc.
15. Dispatch to remote site locations.
16. Loading of software upgrades or fixes into the devices.
Governing Law
In the case of a Product sold in the United States and Canada, this Warranty is governed by the laws of the State of
Illinois and the Province of Ontario, respectively.
Patent and Software Provisions
Motorola will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based
on a claim that the Product or its parts infringe a United
States patent, and Motorola will pay those costs and damages finally awarded against the end user purchaser in any
such suit which are attributable to any such claim, but such
defense and payments are conditioned on the following:
1. that Motorola will be notified promptly in writing by
such purchaser of any notice of such claim;
2. that Motorola will have sole control of the defense of
such suit and all negotiations for its settlement or compromise; and
vi
3. should the Product or its parts become, or in Motorola's
opinion be likely to become, the subject of a claim of
infringement of a United States patent, that such purchaser will permit Motorola, at its option and expense,
either to procure for such purchaser the right to continue using the Product or its parts or to replace or
modify the same so that it becomes non-infringing or
to grant such purchaser a credit for the Product or its
parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime
of the Product or its parts as established by Motorola.
Motorola will have no liability with respect to any claim of
patent infringement which is based upon the combination
of the Product or its parts furnished hereunder with software, apparatus or devices not furnished by Motorola, nor
will Motorola have any liability for the use of ancillary
equipment or software not furnished by Motorola which is
attached to or used in connection with the Product. The
foregoing states the entire liability of Motorola with respect
to infringement of patents by the Product or any its parts
thereof.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce in copies
and distribute copies of such Motorola software. Motorola
software may be used in only the Product in which the software was originally embodied and such software in such
Product may not be replaced, copied, distributed, modified
in any way, or used to produce any derivative thereof. No
other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of
such Motorola software or exercise of rights in such Motorola software is permitted. No license is granted by implication, estoppel or otherwise under Motorola patent rights or
copyrights.
vii
viii
WDE1000/1100 User’s Guide
Contents
Disclaimer ii
Declaration of Conformity ii
Regulatory Requirements iii
Safety and General Information iii
Warranty Information v
PREFACE................................................................................................................. 1
Scope of This Manual............................................................................................................... 1
Arrangement of This Manual.................................................................................................... 1
Applicable Documentation ....................................................................................................... 1
CHAPTER 1 - INTRODUCTION.......................................................................... 3
General Description.................................................................................................................. 3
WDE1000/1100 Specifications................................................................................................. 5
CHAPTER 2 - INSTALLATION........................................................................... 7
Your Package Content .............................................................................................................. 7
Getting to Know Your WDE1000 ............................................................................................ 7
Inserting WDE1000 Into Your Laptop Computer.................................................................... 8
Removing WDE1000 from Your Laptop Computer ................................................................ 8
System Requirements ............................................................................................................... 9
Installing the MCU (Motorola Client Utility) Application..................................................... 10
Uninstalling the MCU (Motorola Client Utility) Application................................................ 23
Upgrading the MCU (Motorola Client Utility) Application................................................... 25
CHAPTER 3 - OPERATION................................................................................ 27
Using the MCU....................................................................................................................... 27
Configuring a new profile....................................................................................................... 28
Activating and Using Your New Profile................................................................................. 39
LED Indicators Operation....................................................................................................... 41
CHAPTER 4 - TROUBLESHOOTING............................................................... 43
General.................................................................................................................................... 43
ix
CHAPTER 5 - GLOSSARY ................................................................................. 45
APPENDIX A - DISABLING/REMOVING WIFI DRIVERS.......................... 49
General.................................................................................................................................... 49
Disabling WiFi Drivers........................................................................................................... 49
For Windows XP Operating System................................................................................. 49
For Windows 2000 Operating System.............................................................................. 50
x
WDE1000/1100 User’s Guide - Preface
Preface
Scope of This Manual
This manual provides instructions for the operation of the WDE1000 (Wireless Device Enabler)
WLAN CardBus Adaptor and the WDE1100 Mini PCI card.
Arrangement of This Manual
This manual is arranged as follows:
• Preface - Contains the scope of the manual and its arrangement.
• Chapter 1-Introduction - Gives a general description of the WDE1000 and its specifications.
• Chapter 2-Installation - Gives information about your WDE1000 package content and instruc-
tions that will enable you to install the card and its operating software.
• Chapter 3 - Operation - Provides you with the information required for setting-up your software
and some initial operation instructions.
• Chapter 4 - Troubleshooting - Gives a list of possible malfunctions that could occur during soft-
ware installation and operation and possible ways to correct them.
• Chapter 5 - Glossary - Gives an explanation to terms and abbreviations that appear in the manual.
Applicable Documentation
For additional information regarding Motorola Client Utility (MCU) application configuration and
use, refer to the On-line Help that is supplied with the application.
1
Preface
This page left blank intentionally
2
WDE1000/1100 User’s Guide - Chapter 1 - Introduction
Chapter 1 - Introduction
General Description
The Wireless Devi ce Enab le r (WDE) CardBus adaptor, referred to throughout this manual as
WDE1000 and the Mini PCI that is referred to as WDE1100, provides modem functionality so that a
client is able to access the WLAN communication services provided by the system network.
This network is an adaptation of an 802.11 System, which provides wireless access to an IP network
using the 4.9 GHz licensed / 2.4 GHz unlicensed spectrum. The system enables the WLAN user to
transmit and receive data at rates of up to 54 Megabits per second (Mbps) by using a version of the
802.11a standard which is adapted for use in the 4.9 GHz band, or 802.11b/g standard for the 2.4 GHz
band.
The WDE is supplied in one of two forms:
• A CardBus adaptor, which is also known by its more generic label as a PCMCIA card
(WDE1000).
• A Mini PCI card. Mini PCI cards are commonly used to add WLAN functionality to notebook
computers such that the function is fully enclosed by the housing of the notebook (WDE1100).
In this manual we refer to the
CardBus form (WDE1000) that has
NOTE
The WDE1000 has the following high level features:
• 2.4 GHz/4.9 GHz band coverage.
• 100 mW typical transmit power.
• FCC 4.9 GHz high power mask.
• Power save mode (for infrastructure communication mode only).
• 802.11e QoS support (EDCA only).
• Two internal antennas and two connectors for external antennas.
• Switched Rx antenna diversity.
• PCMCIA (32 bit) card.
The WDE1000 supports two operational communication modes:
• Infrastructure - The WDE1000 communicates with the network via system infrastructure.
• Ad-hoc - The WDE1000 communicates with another nearby WDE1000, without using system
infrastructure.
A Motorola Client Utility (MCU) application, used with the WDE1000 allows configuration and
monitoring of the connection. A system tray allows WDE1000 status monitoring. A configurable
channel scan list allows for the addition and deletion of channels from the scan list. For single
frequency networks, inclusions of the channel in the scan list significantly improves handoff times.
the same functionality as the Mini
PCI card (WDE1100).
Mini PCI card (WDE1100) will be
available by the end of July 2006 .
3
Chapter 1 - Introduction
A general view of the WDE1000 is shown in Figure 1. A general view of the WDE1100 is shown in
Figure 2.
Figure 1. WDE1000 - General View
Figure 2. WDE1100 - General View
The WDE1100 is installed inside your
Laptop computer and is not visible
NOTE
4
during normal operation.
WDE1000/1100 User’s Guide - Chapter 1 - Introduction
WDE1000/1100 Specifications
Frequency
Range:
802.11b/g: 2.4~2.4835GHz
modified 802.11a @ 4.9GHz:
4.94~4.99GHz
Modulation
Technique:
802.11b (DSSS and CCK)
802.11g (DSSS, CCK and OFDM)
modified 802.11a @ 4.9GHz (OFDM)
Output Power
(typical):
802.11b/g: 18dBm for all modulation rates
4.9GHz band:
20MHz channel: 20dBm for all modulation
rates
10MHz channel: 20dBm for all modulation
rates
5MHz channel: 20dBm for all modulation
rates
Regulatory
Compliance:
Average
Antenna Gain
(typical):
Operation
Modes:
FCC part 90 for 802.11a @ 4.9GHz
FCC part 15 for 802.11 b/g
802.11b/g: 0dBi (on board integral antenna)
4.9GHz band: 0dBi (on board integral
antenna)
Supports external antenna via MMCX
connector
BSS (Infrastructure)
5
Operating
Temperature:
Storage
Temperature:
Operating
Voltage:
Dimensions (W x
L x H):
Chapter 1 - Introduction
IBSS (ad-hoc)
-30 to +60 degrees Celsius
-40 to +85 degrees Celsius
3.3V + 10%
54 x 129 x 5mm (height is 13.8mm at
extension board)
Weight:
Host Interface:
Channel
Support:
Operating
System:
72g
WDE1000 - CardBus 32 bits
WDE1100 - Mini PCI
802 b/g
US: 11 (1~11)
Modified 802.11a
1 7 overlapping 20 MHz bandwidth
channels
2 9 overlapping 10 MHz bandwidth
channels
3 10 overlapping 5 MHz bandwidth
channels
Windows 2000 (Service Pack 4)
Windows XP Professional (Service Pack 2)
Windows XP Tablet (Service Pack 2)
6
WDE1000/1100 User’s Guide - Chapter 2 - Installation
Chapter 2 - Installation
Your Package Content
Verify that your WDE1000 package contains the following:
Item
# Item Description Model Number Quantity
1 WDE1000 Card F2889A 1
2 CD-ROM HKVN4003A 1
Getting to Know Your WDE1000
Figure 3 gives a detailed description of the WDE1000:
Figure 3. WDE1000 - Detailed Description
7
Chapter 2 - Installation
Slo
Inserting WDE1000 Into Your Laptop Computer
Perform the following steps (see Figure 4):
1. Gently insert the WDE1000 into the PCMCIA slot. Verify that the card is sliding along the
guides.
Laptop
Computer
PCMCIA
t
Figure 4. WDE1000 - Installing on a Laptop
2. Push the card into the Laptop PCMCIA connector.
Push Card Inside
PCMCIA Slot
Removing WDE1000 from Your Laptop Computer
Perform the following steps:
1. Press and release the PCMCIA release button to extend it out (see Figure 5).
2. Press the PCMCIA release button again to release the WDE card.
8
WDE1000/1100 User’s Guide - Chapter 2 - Installation
utto
3. Gently pull the card out from the slot.
Pull Card Out
from PCMCIA Slot
PCMCIA Release
B
n
Figure 5. WDE1000 - Removing from a Laptop
System Requirements
The Motorola Client Utility (MCU) requires an IBM PC or compatible computer with the following
minimum configuration:
Processor: Pentium® IV 1.5 GHz or higher
Memory (RAM): 256 MB
PCMCIA slot (for WDE1000): At least one available
Free hard disk space: 20 MB
Drive: CD-ROM
Operating System: Microsoft Windows® 2000 (Service Pack 4)
or Microsoft Windows® XP Professional (Service Pack 2)
or Microsoft Windows® Tablet (Service Pack 2)
9
Loading...