Motorola 89FT6014 User Manual

en

m

Coin Cell

CR2450

Battery

Tray

6IP
TORX
Screw

Battery ‘+’

Face Up

Gun Holster Sensor

Screw Holster

Belt Bracket

Gun Holster

Side Button

Battery Tray

MAC Address

LED

Gun Holster Sensor

PMLN7593 / PMLN7594

*MN003064A01*

MN003064A01-AB

MOTOROLA, MOTO, MOTOROLA SOLUTIONS
and the Stylized M logo are trademarks or registered
trademarks of Motorola Trademar k Holdings, LLC
and are used under license. All ot her trad emarks are
the property of their respective owners.
© 2016 Motorola Solutions, Inc.
All rights reserved.
Printed in

Class B Digital Device

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:

1. This device may not cause harmful
interference, and

2. This device must accept any
interference received, including
interference that may cause undesired
operation.

Note:

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rul es.
These limits are designed to provide
reasonable protection against harmful
interference. However, there is no guarantee
that interference will not occur in a particular
installation.

If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet

on a circuit different from that to which
the receiver is connected.

• Consult the dealer or an experienced

radio or TV technician for help.

• Reorient or relocate the receiving

antenna.

IMPORTANT SAFETY
INFORMATION

RF Energy Exposure and Product Safety
Compliance

Attention!

This device is restricted to Occupational use
only. Before using the device, read the RF
Energy Exposure and Product Safety Guide
which contains important operating
instructions for safe usage and RF energy
awareness and control for Compliance with
applicable standards and Regulations.

Notice to Users (FCC and Industry
Canada)

This device complies with Part 15 of the FCC
rules and RSS 210 of the Industry Canada
rules per the following conditions:

• This device may not cause harmful
interference.

• This device must accept any interfer­ence received, including interference
that may cause undesired operation.

• Changes or modifications made to this
device, not expressly approved by
Motorola, could void the authority of the
user to operate this equipment.

CONSIGNES DE SÉCURITÉ
IMPORTANTES

Expositionaux radio fréquences et sécu­rité du produit

Attention!

Cette capteur ne doit être utilisée qu'à des
finsprofessionnelles. Avant d'utiliser la radio,
lisez leguide Radios bidirectionnelles
portatives : expositionaux radiofréquences e t
sécurité du produit, quicontient d'importantes
instructions de fonctionnementpour une
utilisation sécuritaire et des informations
surl'exposition aux fréquences
radioélectriques, dans lebut d’assurer votre
conformité aux normes etrèglements en
vigueur.

Avis aux utilisateurs (FCC et Industrie
Canada)

Cet appareil est conforme à la Partie 15 des
règlements de la FCC et RSS 210 du
règlement d'Industrie Canada selon les
conditions énumérée sci-dessous:

• Ce dispositif ne doit pas causer d'inter­férences nuisibles.

• Cet appareil doit accepter toute inter­férence reçue, y compris les inter­férences qui peuvent perturber le
fonctionnement.

• Les changements ou les modifications
apportées à ce dispositif, non
expressément approuvées par.

Battery Information:

The sensor is using coin cell CR2450. It is
recommended to use Panasonic brand.
Note: The coin cell is a user replaceable part.

Important Information:

Battery life may temporarily shorten in
low-temperature conditions.

INTRODUCTION

PMLN7593 and PMLN7594 gun holster
sensor detects a hand-gun when the hand­gun is removed from or inserted into the
holster. An event is sent to the device, and
then over the network to applications.

PMLN7593 is applied to the Right-handed
gun holster, while PMLN7594 is applied to
the Left-handed gun holster.

Figure 1: The gun holster sensor in

isometric view

COMP A TIBLE GUN HOLSTER
MODEL

Below is the list of weapon types that are
supported by Safariland 6280 and 6360
models:

• Sig Sauer P226 9 mm

• Sig Sauer P226.40

• Smith & Wesson M&P 9 mm

• Smith & Wesson M&P.40

• Glock 17

• Glock 19

• Glock 21

• Glock 22

• Glock 34

P AIRING AND CONNECTION
METHOD

1. Press the side button for three seconds.
Blue LED blinks, which indicates the
sensor is discoverable.

2. On your device, select the sensor from
the list:
e.g. G_yyy_<last four digit from the MAC
address>.

3. The sensor is connected to the device.

• Blue LED is steady ON for three sec-

onds upon connection.

OPERATING INSTRUCTIONS

The sensor can be connected to one device
at a time.

Installing the Sensor

1. Unscrew the battery tray.

2. Insert the cell into the tray.

3. Screw the battery tray.

4. Attach the sensor within the gun holster.

Figure 2: PMLN7594 (Left) and

PMLN7593 (Right)

Mounting the Sensor within Holster and
Belt Bracket

1. Arrange the components as in Figure 3
with the sensor within the holster and
belt bracket by facing the M-logo to Belt
Bracket.

2. Screw the belt loop plate to the holster
with the sensor in between.

Figure 3: Mounting the sensor within

holster and belt bracket

CALIBRATION

The sensor will need to be calibrated when
using it for the first time.
Red LED will be turned ON when the sensor
is NOT calibrated.
Withdraw and holster the gun to perform
calibration. Each withdraw and holster action
interval should be approximately five seconds
or more. Repeat the process until the red
LED is turned OFF . It may take approximately
three times for successful calibration.

3.

SOFTWARE UPGRADE

1. Red and Blue LED blink alternately
during the sensor software update.

OTHER FUNCTIONS

1. Reset: Disconnect Bluetooth. Press the
side button for more than 15 seconds to
reset the sensor. This will clear the
previous pairing data and calibration
data on the sensor as well.

2. Still Alive Indicator: Press the side button
to check the sensor status. Blue LED
indicates the unit is responsive and
good. If there is no Blue LED, either the
battery is drained or the unit is faulty.

NOTES