Motorola 89FT5861 Users Manual
APX 1000
APX™ TWO-WAY RADIOS
APX 1000
MODEL 2
USER GUIDE
English
Antenna
Accessory
Connector
Multi-Function Knob
(MFK):
Primary Feature:
_________________
Secondary Feature:
_________________
Battery
Microphone
Top Lightbar
Side Button 1
__________
PTT Button
Top Side
(Select)
Button
__________
Main
Speaker
Microphone
Side Button 2
__________
Home Button
LED
Menu Select
Buttons
Data Feature
Button
4-Way Navigation
Button
Main Display
Top (Orange)
Button
__________
PMLN6812A
*PMLN6812A*
Receiving and Transmitting
1 Select zone/channel.
2 Listen for a transmission.
OR
Press and hold Volume Set button.ORPress Monitor button and listen for activity.
Sending an Emergency Alarm
receive.
3 Adjust volume, if necessary.
4 Press the PTT button to transmit; release to
1 Press and hold the Emergency button*.
2 The display shows Emergency and the
current zone/channel. Radio sounds a short,
medium-pitched tone, and the LED blinks red
momentarily.
Radio On/Off
• On – Press and hold the MFK until the display
3 When acknowledgment is received, you hear
lights up.
four beeps; alarm ends; and radio exits
• Off – Press and hold the MFK until you see
emergency.
Power off?, then press Menu Select button
below Yes.
* Default emergency button press timer is set
to 1 second. This timer is programmable, see
page 56 in the user guide for details.
To exit emergency at any time, press and hold
the Emergency button.
Zones and Channels
1 Press the MFK to see on the screen.
2 Turn the MFK to scroll to desired zone or
channel and exit Mode Change.
channel.
3 Press MFK to select the desired zone or
ATTENTION!
APX™ 1000 Series
®
Digital Portable Radios
m
Quick Reference Card
ASTRO
This radio is restricted to Occupational use only. Before using
RF Energy Exposure and Product Safety
Guide for Portable Two-Way Radios
the radio, read the RF Energy Exposure and Product Safety
Guide for Portable Two-Way Radios which contains important
Radio Controls
operating instructions for saf e usage and RF energy awareness
and control for Compliance with applicable standards and
Regulations.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola T rad emark Holdings, LLC and
are used under license. All other trademarks are the property of thei r respective owne rs. ©2014 by Motorola Solutions, Inc. All Rights Reserved. 06/14. 1303
East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.
u
t
8
V
O
M
HOR .
i
j
k
the radio.
n
o
m
Menu Navigation
< or > to Menu Entry.
{, |, or } directly below Menu
Entry to select.
H to exit.
U or D to scroll through sub-list.
{, |, or } directly below
Menu Entry to select.
with the radio.
Off = User is currently not associated
The more stripes, the stronger the
Blinking = Device registration or user
signal strength for the current site
(trunking only).
On = User is currently associated with
Blinks when the battery is low.
registration with the server failed due
to an invalid username or pin.
Data activity is present.
Direct radio to radio communication or
connected through a repeater.
On = Direct
Off = Repeater
MFK is in Mode Change feature.
MFK is in Volume Change feature.
On = Secure operation.
This channel is being monitored.
L = Radio is set at Low power.
H = Radio is set at High power.
voice call.
Off = Clear operation.
Blinking = Receiving an encrypted
Priority-One Channel
during scan.
Priority-Two Channel
during scan.
Scanning a scan list.
Blinking dot = Detects activity on the
Steady dot = Detects activity on the
The vote scan feature is enabled.
Sending an Emergency Call
1 Press the Emergency button.
into the microphone.
2 Press and hold the PTT button. Speak clearly
3 Release the PTT button to end call.
4 Press and hold Emergency button to exit
emergency.
To exit emergency at any time, press and hold
the Emergency button.
Receiving a call or data
Transmitting a call or data
Sending a Silent Emergency Call
not light up, and there is no tone.
1 Press the Emergency button.
2 The display does not change; the LED does
Press and hold the Emergency button to exit
emergency state.ORPress and release the PTT button to exit the
Silent Emergency Alarm mode and enter
3 Silent emergency continues until you:
regular dispatch or Emergency Call mode.
To exit emergency at any time, press and hold
the Emergency button.
Display Status Icons
English
Declaration of Conformity
i
English
Model Name: APX 1000
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Declaration of Conformity
Responsible Party
Name: Motorola Solutions, Inc.
Address: 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.
Phone Number: 1-800-927-2744
Hereby declares that the product:
conforms to the following regulations:
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
Note:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
ii
English
Contents
Documentation Copyrights . . . . . . . . . . . . . . .xii
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
iii
English
ASTRO 25 Enhanced Data . . . . . . . . . . . . . . . . . . . 2
Dynamic System Resilience (DSR) . . . . . . . . . . . . . 2
CrossTalk Prevention . . . . . . . . . . . . . . . . . . . . . . . 3
SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . .1
Notations Used in This Manual . . . . . . . . . . . . . . . . . 1
Additional Performance Enhancement . . . . . . . . . . . 2
Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What Your Dealer/System Administrator
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . .1
Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . 4
Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . .5
Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . . 6
Attaching the Accessory Connector
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . .7
Preparing Your Radio for Use . . . . . . . . . . . . . .4
Contents
This User Guide contains all the information you need
to use the APX™ 1000 Series Digital Portable Radios.
for Portable Two-Way Radios . . . . . . . . . . . . . . . .viii
Declaration of Conformity . . . . . . . . . . . . . . . . .i
RF Energy Exposure and Product Safety Guide
Important Safety Information . . . . . . . . . . . . .viii
Notice to Users (FCC and Industry Canada) . . . . . .ix
Software Version . . . . . . . . . . . . . . . . . . . . . . . .ix
Informations importantes sur la
produit pour radios bidirectionnelles portatives . . . . x
Exposition aux radiofréquences et sécurité du
sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Version du logiciel . . . . . . . . . . . . . . . . . . . . . . .xi
Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Avis aux utilisateurs (FCC et Industrie
Computer Software Copyrights . . . . . . . . . . . xii
LED Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Top Lightbar Indications . . . . . . . . . . . . . . . . . . . . .23
Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . 24
Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Phone Call Display and Alert Prompts . . . . . . . . . . 28
Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 30
Saving a Zone and Channel to a Softkey . . . . . . . .32
Saving a Zone and Channel to a Programmable
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Receiving and Responding to a Talkgroup Call . . .34
Receiving and Responding to a Private Call
(Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Receiving and Responding to a Telephone Call
(Trunking Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Using Mode Select Feature . . . . . . . . . . . . . . . . . . 32
Receiving and Responding to a Radio Call . . . . . . 33
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 36
Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . .36
Making a Private Call (Trunking Only) . . . . . . . . . . .36
Making an Enhanced Private Call (Trunking Only) .37
Making a Telephone Call (Trunking Only) . . . . . . . .38
General Radio Operation . . . . . . . . . . . . . . . . 29
Home Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Data Feature Button . . . . . . . . . . . . . . . . . . . . . . .14
4-Way Navigation Button . . . . . . . . . . . . . . . . . . . .14
Multi-Function Knob (MFK) . . . . . . . . . . . . . . . . . . 1 5
Assignable Radio Functions . . . . . . . . . . . . . . . . . . 11
Assignable Settings or Utility Functions . . . . . . . . . 12
Using the Menu Select Buttons . . . . . . . . . . . . . . . 13
Using the Navigation Buttons . . . . . . . . . . . . . . . . . 14
Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 8
Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . 10
Identifying Radio Controls . . . . . . . . . . . . . . . . .9
Programmable Features . . . . . . . . . . . . . . . . . . . . . 11
Accessing the Preprogrammed Functions . . . . . . . 13
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . 15
Identifying Status Indicators . . . . . . . . . . . . . .16
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Text Messaging Service (TMS) Icons . . . . . . . . . . 19
Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . 20
Call Type Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Top Lightbar and LED Indicators . . . . . . . . . . . . . . 22
Contents
iv
English
Contents
Adding a Contact to a Call List . . . . . . . . . . . . . . . 49
Removing a Contact from a Call List . . . . . . . . . . . 49
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . 50
Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . 50
Changing the Scan List Status . . . . . . . . . . . . . . . 51
Viewing and Changing the Priority Status . . . . . . 51
Turning Scan On or Off . . . . . . . . . . . . . . . . . . . . . 52
Making a Dynamic Priority Change (Conventional
Scan Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Deleting a Nuisance Channel . . . . . . . . . . . . . . . . 52
Restoring a Nuisance Channel . . . . . . . . . . . . . . . 53
Receiving a Call Alert Page . . . . . . . . . . . . . . . . . . 54
Sending a Call Alert Page . . . . . . . . . . . . . . . . . . . 54
Sending an Emergency Alarm . . . . . . . . . . . . . . . . 56
Sending an Emergency Call (Trunking Only) . . . . 57
Sending an Emergency Alarm with Emergency
Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . .55
Sending a Silent Emergency Alarm . . . . . . . . . . . . 58
Changing Channels during Emergncy . . . . . . . . . . 58
Using the Emergency Keep-Alive Feature . . . . . . . 58
v
English
Selecting or Changing the ARS Mode . . . . . . . . . . 59
Automatic Registration Service (ARS) . . . . . . . . . . 59
Receiving a Selective Call . . . . . . . . . . . . . . . . . . .4 2
Making a Selective Call . . . . . . . . . . . . . . . . . . . . .42
Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . .40
Conventional Mode Operation . . . . . . . . . . . . . . . .40
Repeater or Direct Operation . . . . . . . . . . . . . . . . .39
Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . .39
Receiving and Making a Selective Call (ASTRO
Conventional Only) . . . . . . . . . . . . . . . . . . . . . . . . .41
Advanced Call Features . . . . . . . . . . . . . . . . . . . . . 41
Selecting a Talkgroup . . . . . . . . . . . . . . . . . . . . . .43
Using the Talkgroup Call Feature (Conventional
Operation Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Sending a Status Call . . . . . . . . . . . . . . . . . . . . . . .43
Requesting a Reprogram (Trunking Only) . . . . . . .45
Classifying Regrouped Radios . . . . . . . . . . . . . . . .45
Entering the Dynamic Zone to Select a Dynamic
Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Saving a Channel in the Dynamic Zone from List
Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Deleting a Channel in the Dynamic Zone . . . . . . . .47
Using the Dynamic Regrouping Feature (Trunking
Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Using Dynamic Zone Programming (DZP) . . . . . . .45
Making a Private Call from Contacts . . . . . . . . . . . .48
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Advanced Features . . . . . . . . . . . . . . . . . . . . . 41
Accessing the Outdoor Location Feature . . . . . . . .71
Saving a Waypoint . . . . . . . . . . . . . . . . . . . . . . . . .72
Viewing a Saved Waypoint . . . . . . . . . . . . . . . . . . .73
Deleting a Single Saved Waypoint . . . . . . . . . . . . .73
Deleting All Saved Waypoints . . . . . . . . . . . . . . . .74
Measuring the Distance and Bearing from a Saved
Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Using the Location Feature While in Emergency
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
The Outdoor Location Feature (Using GPS) . . . . . .70
Enabling MGRS Coordinates . . . . . . . . . . . . . . . . .71
Using the Failsoft System . . . . . . . . . . . . . . . . . . . .75
Going Out of Range . . . . . . . . . . . . . . . . . . . . . . . .76
Using the Site Trunking Feature . . . . . . . . . . . . . . .76
Trunking System Controls . . . . . . . . . . . . . . . . . . . 75
Logging In as a User . . . . . . . . . . . . . . . . . . . . . . .60
Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Accessing the User Login Feature . . . . . . . . . . . . . 60
Accessing the TMS Features . . . . . . . . . . . . . . . . . 62
Sending a Quick Text Message . . . . . . . . . . . . . . . 62
Appending a Priority Status to a Text Message . . . 63
Using the Priority Status and Request Reply
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Removing a Priority Status from a Text Message . 64
Appending a Request Reply to a Text Message . . 64
Removing a Request Reply from a Text Message 64
Appending a Priority Status and a Reply Request to
a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing a Priority Status and a Reply Request
Text Messaging Service (TMS) . . . . . . . . . . . . . . . 61
Viewing the Current Site . . . . . . . . . . . . . . . . . . . . .77
Changing the Current Site . . . . . . . . . . . . . . . . . . .77
Locking and Unlocking a Site . . . . . . . . . . . . . . . . .76
Viewing and Changing a Site . . . . . . . . . . . . . . . . .77
from a Text Message . . . . . . . . . . . . . . . . . . . . . . .65
Receiving a Text Message . . . . . . . . . . . . . . . . . . 65
Viewing a Text Message from the Inbox . . . . . . . .66
Managing Text Messages . . . . . . . . . . . . . . . . . . . 65
Responding to the notification of Upgrade . . . . . . .77
(ASTRO 25 and ASTRO Conventional) . . . . . . . . 77
Programming Over Project 25 (POP 25)
Replying to a Received Text Message . . . . . . . . .66
Managing Sent Text Messages . . . . . . . . . . . . . . . 67
Voice Announcement . . . . . . . . . . . . . . . . . . . . . . . 78
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Viewing a Sent Text Message . . . . . . . . . . . . . . . .67
Sending a Sent Text Message . . . . . . . . . . . . . . . 68
Deleting a Text Message . . . . . . . . . . . . . . . . . . . . 68
Deleting All Text Messages . . . . . . . . . . . . . . . . . .69
Viewing the Recent Calls . . . . . . . . . . . . . . . . . . . .79
Selecting the Power Level . . . . . . . . . . . . . . . . . . . .80
Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . . .81
Understanding the GPS Feature . . . . . . . . . . . . . . 69
Enhancing GPS Performance . . . . . . . . . . . . . . . . 70
The Global Positioning System (GPS) . . . . . . . . . . 69
Contents
vi
English
Contents
Checking the Battery Charge Status . . . . . . . . . . . 94
Servicing Your Radio . . . . . . . . . . . . . . . . . . . . . . . 93
Taking Care of the Battery . . . . . . . . . . . . . . . . . . .94
LED and Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Fuel Gauge Icon . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Battery Recycling and Disposal . . . . . . . . . . . . . . . 95
vii
English
Emergency Channel . . . . . . . . . . . . . . . . . . . . . . . 97
Non-Commercial Call Channel . . . . . . . . . . . . . . . 97
Highlights for the Accessories . . . . . . . . . . . . . . . . . 96
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Special Channel Assignments . . . . . . . . . . . . . . . . 97
Appendix: Maritime Radio Use in the VHF
Frequency Range . . . . . . . . . . . . . . . . . . . . . . .97
Distress and Safety Frequencies . . . . . . . . . . . . . 100
Operating Frequency Requirements . . . . . . . . . . . .98
Declaration of Compliance for the User of
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Commercial Warranty . . . . . . . . . . . . . . . . . . .105
Editing the Time and Date . . . . . . . . . . . . . . . . . . .85
Enabling and Disabling the Radio Alias . . . . . . . . .81
Selecting the Audio Speaker . . . . . . . . . . . . . . . . . .82
Controlling the Display Backlight . . . . . . . . . . . . . . .83
Locking and Unlocking the Controls . . . . . . . . . . . .83
Turning the Switch and Buttons Tones On or Off . .83
Turning Voice Mute On or Off . . . . . . . . . . . . . . . . .84
Using the Time-Out Timer . . . . . . . . . . . . . . . . . . . .84
Setting the Time and Date . . . . . . . . . . . . . . . . . . .85
Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Using the Conventional Squelch Operation
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Using the PL Defeat Feature . . . . . . . . . . . . . . . . . .86
Using the Digital PTT ID Feature . . . . . . . . . . . . . .86
Using the Smart PTT Feature (Conventional Only) 87
Accessing the Battery Info screen . . . . . . . . . . . . .88
Accessing the Radio Information . . . . . . . . . . . . . .88
Viewing the IP Information . . . . . . . . . . . . . . . . . . .89
Viewing the Control Assignments . . . . . . . . . . . . .90
IMPRES™ Battery Annunciator . . . . . . . . . . . . . . .87
Accessing the General Radio Information . . . . . . . .88
Cleaning Your Radio . . . . . . . . . . . . . . . . . . . . . . . .92
Handling Your Radio . . . . . . . . . . . . . . . . . . . . . . . .93
Caring for Your Radio . . . . . . . . . . . . . . . . . . . . . . .91
Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
(e.i.r.p.) is not more than that necessary for successful
communication.
This radio transmitter has been approved by Industry
Canada to operate with the Motorola-approved antenna
types with the maximum permissible gain and required
antenna impedance for each antenna type indicated.
Antenna types not included, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
ATTENTION!
Important Safety Information
RF Energy Exposure and Product Safety Guide
for Portable Two-Way Radios
This radio is restricted to Occupational use only.
Before using the radio, read the RF Energy Exposure and
Product Safety Guide for Portable Two-Way Radios
which contains important operating instructions for safe
usage and RF energy awareness and control for
Compliance with applicable standards and Regulations.
For a list of Motorola-approved antennas, batteries, and
other accessories, visit the following website:
http://www.motorolasolutions.com/APX
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power
Important Safety Information
English
viii
Software Version
ix
English
Software Version
All the features described in the following sections are
supported by the radio's software version R12.00.00 or
including interference that may cause undesired
operation.
expressly approved by Motorola, could void the user's
later.
See Accessing the Radio Information on page 88 to
determine your radio's software version.
Check with your dealer or system administrator
for more details of all the features supported.
Notice to Users (FCC and Industry Canada)
This device complies with Part 15 of the FCC rules and
RSS 210 of the Industry Canada rules per the conditions
listed below:
1 This device may not cause harmful interference.
2 This device must accept any interference received,
authority to operate this equipment.
3 Changes or modifications made to this device, not
autres utilisateurs, le type et le gain de l'antenne doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (P.I.R.E.) ne soit pas plus forte qu'il
ne le faut pour établir la communication.
Le présent émetteur a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne agréés par
Motorola et ayant un gain admissible maximal ainsi que
l'impédance requise pour chaque type d'antenne indiqué.
Les types d'antenne non inclus, dont le gain est supérieur
au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
ATTENTION!
Informations importantes sur la
sécurité
Exposition aux radiofréquences et sécurité du
produit pour radios bidirectionnelles portatives
Cette radio ne doit être utilisée qu'à des fins
professionnelles. Avant d'utiliser la radio, lisez le guide
Exposition aux radiofréquences et sécurité du produit
pour radios bidirectionnelles portatives, qui contient
d'importantes instructions de fonctionnement pour une
utilisation sécuritaire et des informations sur l'exposition
aux fréquences radioélectriques afin d'assurer la
conformité aux normes et règlements applicables.
Pour obtenir une liste d'antennes et d'autres accessoires
approuvés par Motorola, consultez le site Web:
http://www.motorolasolutions.com/APX
Selon la règlementation d'Industrie Canada, cet émetteur
radio ne peut être utilisé qu'avec une antenne dont le
type et le gain maximal (ou minimal) sont approuvés par
Industrie Canada pour cet émetteur. Afin de limiter les
interférences radio pour les
Informations importantes sur la sécurité
x
Français Canadien
Version du logiciel
xi
Français Canadien
Version du logiciel
Toutes les fonctionnalités décrites dans les sections
suivantes sont prises en charge par la version du logiciel
R12.00.00 ou ultérieure de la radio.
Vérifiez auprès de votre détaillant ou de l'administrateur
de système pour obtenir des renseignements sur les
fonctionnalités prises en charge.
Avis aux utilisateurs (FCC et Industrie
Canada)
Cet appareil est conforme à la Partie 15 des règlements
de la FCC et RSS 210 du règlement d'Industrie Canada
nuisibles.
selon les conditions énumérées ci-dessous:
1 Ce dispositif ne doit pas causer d'interférences
compris les interférences qui peuvent perturber le
fonctionnement.
dispositif, non expressément approuvées par Motorola,
peuvent annuler le droit de l'utilisateur à utiliser cet
2 Cet appareil doit accepter toute interférence reçue, y
3 Les changements ou les modifications apportées à ce
équipement.
Documentation Copyrights
No duplication or distribution of this document or any
Computer Software Copyrights
The Motorola products described in this manual may
portion thereof shall take place without the express
written permission of Motorola. No part of this manual
may be reproduced, distributed, or transmitted in any
form or by any means, electronic or mechanical, for any
purpose without the express written permission of
Motorola.
include copyrighted Motorola computer programs stored
in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola
certain exclusive rights for copyrighted computer
programs, including, but not limited to, the exclusive right
to copy or reproduce in any form the copyrighted
Disclaimer
computer program. Accordingly, any copyrighted
Motorola computer programs contained in the Motorola
products described in this manual may not be copied,
The information in this document is carefully examined,
and is believed to be entirely reliable. However, no
responsibility is assumed for inaccuracies. Furthermore,
Motorola reserves the right to make changes to any
products herein to improve readability, function, or
design. Motorola does not assume any liability arising out
of the applications or use of any product or circuit
described herein; nor does it cover any license under its
reproduced, modified, reverse-engineered, or distributed
in any manner without the express written permission of
Motorola. Furthermore, the purchase of Motorola
products shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola,
except for the normal non-exclusive license to use that
arises by operation of law in the sale of a product.
patent rights, nor the rights of others.
Computer Software Copyrights
xii
English
Getting Started
!
!
!
Caution
An operational procedure, practice, or condition,
etc., which may result in injury or death if not
carefully observed.
An operational procedure, practice, or
condition, etc., which may result in damage
to the equipment if not carefully observed.
An operational procedure, practice, or condition,
etc., which is essential to emphasize.
1
English
Notations Used in This Manual
Throughout the text in this publication, you will notice the use of
WARNING, Caution, and Note. These notations are used to
emphasize that safety hazards exist, and the care that must be
taken or observed.
How to Use This Guide
Getting Started
Take a moment to review the following:
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1
Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1
Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Additional Performance Enhancement . . . . . . . . . . . . . page 2
What Your Dealer/System Administrator
This User Guide covers the basic operation of the APX™ 1000
Note:
Portables.
However, your dealer or system administrator may have
customized your radio for your specific needs. Check with your
dealer or system administrator for more information.
Additional Performance Enhancement
The following are some of the latest creations designed to
enhance the security, quality and efficiency of your radio.
Buttons and keys are shown in bold print
ASTRO 25 Enhanced Data
or as an icon.
Menu entries are shown similar to the
ASTRO 25 Enhanced Data is optimized to handle different
message sizes and update rates from different applications.
Install Enhanced Data to the Integrated Data system with a
way they appear on your radio’s display.>This means “Press the right side of the
Dynamic System Resilience (DSR)
software installation to improve data channel efficiency and
enable denser network traffic.
4-way Navigation button”.
DSR seamlessly switches the radio system to a backup master
site during system failures. DSR also provides additional
indication e.g. failure detection, fault recovery, and redundancy
H
or
Example Description
Home button
Phone
within the system to address to the user in need. Mechanisms
related to the Integrated Voice and Data (IV&D) or data centric
are all supported by DSR.
The following special notations identify certain items:
Getting Started
2
English
Getting Started
Can Tell You
What Your Dealer/System Administrator
Check with your dealer or system administrator for the correct
radio settings, if the radio is to be operated in extreme
temperatures (less than -30 °C or more than +60 °C), to ensure
proper top and front display operation.
You can also consult your dealer or system administrator about
the following:
• Is your radio preprogrammed with any preset conventional
channels?
features?
• Which buttons have been preprogrammed to access other
• What optional accessories may suit your needs?
3
English
CrossTalk Prevention
This feature prevents crosstalk scenarios from happening,
especially when a wideband antenna is used. This feature
allows the adjustment of the Trident Transmitting SSI clock rate
in the radio to be different from the Receiving Frequency. This
subsequently reduces the possibilities of radio frequency
interfering spurs and it also prevents crosstalk.
SecureNet
SecureNet allows user to perform secured communications on
an Analog or Motorola Data Communication (MDC) channel.
labeled “hazardous atmosphere”.
!
WARNING
!
To avoid a possible explosion:
• DO NOT replace the battery in any area
• DO NOT discard batteries in a fire.
radio off to ensure a full charge.
Charging the Battery
The Motorola-approved battery shipped with your radio is
Preparing Your Radio for Use
Battery Charger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Assemble your radio by following these steps:
Charging the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . page 6
Attaching the Accessory Connector Cover . . . . . . . . . . page 6
uncharged. Prior to using a new battery, charge it for a minimum
of 16 hours to ensure optimum capacity and performance.
For a list of Motorola-authorized batteries available for use
with your radio, see Accessories on page 96.
Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
Battery Charger
Note: When charging a battery attached to a radio, turn your
To charge the battery, place the battery, with or without the
radio, in a Motorola-approved charger. The charger’s LED
indicates the charging progress; see your charger’s user guide.
For a list of chargers, see Accessories on page 96.
Preparing Your Radio for Use
4
English
Preparing Your Radio for Use
Battery Latch is at the bottom of the battery.
To remove the battery,
turn the radio off. Lift up
the latch then slide the
battery down to remove
the battery from the radio.
You can view the status of
the IMPRES™ battery if
the radio is using an
IMPRES™ battery. See
IMPRES™ Battery
Annunciator on page 87
for more information.
5
English
Attaching the Battery
With the radio turned off, slide the battery into the radio’s frame
until click into place.
connector cover when not in use.
Hooked End
Thumbscrew
Hex Socket Head
Cover
Attaching the Accessory Connector
The accessory connector is located on the antenna side of the
radio. It is used to connect accessories to the radio.
Note: To prevent damage to the connector, shield it with the
Insert the hooked
end of the cover
into the slot above
the connector.
Press downward on
the cover’s top to
seat it in the slot.
Once in place,
tighten by rotating
the thumbscrew
clockwise by hand. To remove the
accessory connector cover, rotate the thumbscrew
counterclockwise until it disengages from the radio.
If the thumbscrew is too tight, use an Allen wrench to loosen
it first.
Rotate and lift the connector cover to disengage it from
the radio.
Attaching the Antenna
With the radio turned off, set the antenna in its receptacle and
turn clockwise to attach it to the radio.
To remove the antenna, turn the antenna counterclockwise.
Make sure you turn off the radio first.
Preparing Your Radio for Use
6
English
Preparing Your Radio for Use
Turning On the Radio
Press and hold the Multi-Function Knob (MFK) until the radio
display lights up, then release the MFK.
If the power-up test is successful, you see the Home screen.
XX/YY (XX/YY is an alphanumeric code).
Note: If the power-up test is unsuccessful, you see Error
Turn off your radio, check the battery, and turn the
radio back on. If your radio fails the power-up test
again, record the Error XX/YY code and contact
7
English
your dealer.
Attaching the Belt Clip
Align the grooves of the belt clip
with those of the radio and
press upward until you hear a
click.
To remove the clip, use a flat-
bladed object to press the belt
clip tab away from the radio.
Then, slide the clip downward
and away from your radio.
Tab
Main
Speaker
Multi-Function Knob (MFK) on page 15 to toggle the
function of the MFK.
for increased loudness and intelligibility, especially in
areas with loud background noises.
Adjusting the Volume
Your radio is preprogrammed to reset to medium volume rate,
which is Level 12, by default whenever the radio powers up.
To increase the volume, turn the MFK clockwise. The display
shows volume bars and volume level when you change the
volume.
Note: If Volume Change is secondary featu r e of MFK, see
To decrease the volume, turn this MFK counterclockwise.
Note: Ensure that the main speaker is pointed towards you
, press the Menu Select button
Power off?
to power off.
Yes
below
To turn off your radio, press and hold the MFK until the radio
display shows
Preparing Your Radio for Use
8
English
Identifying Radio Controls
9
English
Assignable Radio Functions . . . . . . . . . . . . . . . . . . page 11
Assignable Settings or Utility Functions. . . . . . . . . . page 12
Using the Menu Select Buttons . . . . . . . . . . . . . . . . page 13
Identifying Radio Controls
Take a moment to review the following:
Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . page 10
Programmable Features . . . . . . . . . . . . . . . . . . . . . . . page 11
Using the Navigation Buttons. . . . . . . . . . . . . . . . . . page 14
Accessing the Preprogrammed Functions. . . . . . . . . . page 13
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 15
Antenna
1
LED
2
Accessory
Connector
5
Home Button
6
7
4-Way
Navigation
Button
Microphone
4
T op (Orange)
Button*
3
Battery
Latch (at the
bottom)
8
10
Menu Select
Buttons
12
13
Main Display
11
Data Feature
Button
9
Multi-
Function
Knob
(MFK)*
Side Button 2*
Side Button 1*
16
Push-to-Talk
(PTT) Button
19
Top Side
(Select)
Button*
Battery
14
15
Top
Lightbar
20
* These radio controls/buttons are programmable.
Speaker
17
Microphone
18
Radio Parts and Controls
Identifying Radio Controls
English
10
Identifying Radio Controls
Dynamic Priority (Conventional Only) – Allows any channel
in a scan list (except for the Priority-One channel) to temporarily
replace the Priority-Two channel.
Emergency – Depending on the programming, initiates or
cancels an emergency alarm or call.
Information – Displays the information of the radio.
Internet Protocol Address – Displays the Internet Protocol (IP)
address, device name and status of the radio.
Location – Determines the current location (latitude, longitude,
time and date), and also the distance and bearing to another
location. Or, turns the GPS functionality on or off for all location.
Message – Enters the current message list.
11
English
Mode Select – Long-press programs a button with the radio's
current zone and channels; then once programmed, the short
press of that button jumps the radio to the programmed zone
and channel.
Monitor (Conventional Only) – Monitors a selected channel
for all radio traffic until function is disabled.
Multiple Private Line (Conventional Only) – Selects the
Multiple Private Line lists.
Nuisance Delete – Temporarily removes an unwanted channel,
except for priority channels or the designated transmit channel,
from the scan list.
Programmable Features
Any reference in this manual to a control that is
“preprogrammed” means that the control must be programmed
by a dealer or qualified radio technician using the radio's
programming software, in order to assign a feature to that
control.
The programmable buttons can be programmed as shortcuts to
radio functions or preset channels/groups depending on the
duration of a button press:
duration (between 0.25 seconds and 3.75
seconds).
Assignable Radio Functions
• Press – Pressing and releasing rapidly.
• Long press – Pressing and holding for the preprogrammed
• Hold down – Keeping the button pressed.
Call Alert – Allows the radio to function like a pager, or to verify
if a radio is active on the system.
Call Response – Allows you to answer a private call.
Channel – Selects a channel.
Contacts – Selects the Contacts menu.
Site Lock/Unlock (Trunking Only) – Locks onto a specific site.
Status – Sends data calls to the dispatcher about a predefined
status.
Talkaround/Direct (Conventional Only) – Toggles between
using a repeater and communicating directly with another rad i o.
Talkgroup (Conventional Only) – Allows a call from an
individual radio to a group of radios.
Selects the text messaging
menu.
Text Messaging Service (TMS) –
User – Automatically registers with the server.
TMS Quick Text – Selects a predefined message.
Assignable Settings or Utility Functions
Zone Select – Allows selection from a list of zones.
Light/Flip – Press the button to toggle the display backlight on
or off.
Keypad/Control Lock – Locks or unlocks the Menu Select,
Navigation, Home, Data, programmable buttons and rotary
knob.
Voice Announcement – Audibly indicates the current feature
mode, Zone or Channel the user has just assigned.
V o ice Mute – Toggles voice mute on or off.
Volume Set Tone – Sets the volume set tone.
Phone – Allows you to make and receive calls similar to
standard phone calls.
Private Call (Trunking Only) – Allows a call from an individual
radio to another individual radio.
Private Line Defeat (Conventional Only) – Overrides any
coded squelch (DPL or PL) that is preprogrammed to a channel.
Radio Profiles – Allows for easy access to a set of
preprogrammed visual and audio settings of the radio.
Recent Calls – Allows for easy access to the list of calls
recently received or made.
Repeater Access Button (RAB) (Conventional Only) –
Allows to manually send a repeater access codeword.
Reprogram Request (Trunking Only) – Notifies the dispatcher
you want a new dynamic regrouping assignment.
Request-To-Talk (Conventional Only) – Notifies the
dispatcher you want to send a voice call.
Scan – Toggles scan on or off.
Secure Transmission Select (Conventional and Trunking) –
Toggles to transmit is secure or clear transmission.
Selective Call (Conventional Only) – Calls an assigned radio.
Site Display/Search (Trunking Only) – Displays the current
site ID and RSSI value; performs site search for AMSS
(Automatic Multiple Site Select) operation.
Identifying Radio Controls
English
12
Identifying Radio Controls
Data Feature
Button
4-Way Navigation Button
Home Button
Mute | Chan | Zone
Menu Select
Buttons
Softkeys
list of features activated in your radio.
Using the Menu Select Buttons
The Menu Select buttons access the menu entries of features.
Note: Check with your dealer or system administrator for the
Y our radio may be preprogrammed differently from the following
example, but the steps for selecting a channel may appear as
shown below:
• Press the Menu Select button ( | ) directly below Chan.
13
English
OR
Accessing the Preprogrammed Functions
You can access various radio functions through one of the
following ways:
• A short or long press of the relevant programmable buttons.
• Use the Menu Select Buttons ({, |, and }).
Data Feature Button
Use this button to access data-related features, such as the
4-Way Navigation Button
Text Messaging Service (TMS) feature screen.
Use this button to scroll up, down, left or right.
Press and release one of the button to scroll from one entry to
H button is also used to save
Using the Navigation Buttons
Home Button
The H button returns you to the Home (default) screen. In most
cases, this is the current mode.
For selected radio features, the
the next one. Press and hold one of the button to have your
user-edited radio settings or information before returning you to
radio toggles through the list automatically (release the button
the Home screen.
to stop).
H to go to
Note: Some features do not require you to press
the Home screen. Refer to the individual feature
sections in this manual for further details on saving
user-edited radio settings or information.
Identifying Radio Controls
English
14
Loading...