How it Works
Motorola
Loading...
89FT3803
User Manual
58 pgs2.84 Mb0

Motorola 89FT3803 User Manual

Download
Page 1
TWO-WAY RADIO
@6864110R04@
6864110R04-O
PRELIMINARY
User's Guide
Models XU1100, XU2100, and XU2600
Models XV1100, XV2100, and XV2600
010449-O
Page 2
Page 3
6881038B80.book Page i Thursday, August 30, 2001 5:33 PM
Safety and General Information
Important Information on Safe and Efficient Operation Read This Information Before Using Your Radio
The information provided in this document supersedes the general safety information contained in user guides published prior to July 2000. For information regarding radio use in a hazardous atmosphere please refer to the Factory Mutual (FM) Approval Manual Supplement or Instruction Card, which is included with radio models that offer this capability.
RF Operational Characteristics
Your radio contains a transmitter and a receiver. When it is ON, it receives and transmits radio frequency (RF) energy. The XTN Series VHF radios operate in the frequency range of 151-161 MHz, the XTN Series UHF radios operate in the frequency range of 461-469 MHz. When you communicate with XU1100 or XV1100 radios the output power level is 1.0 watt, with other XTN Series radios, the output power level is 2.0 watts
Exposure to Radio Frequency Energy
Your Motorola radio is designed to comply with the following national and international standards and guidelines regarding exposure of human beings to radio frequency electromagnetic energy:
• United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J
• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992
• Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
PRELIMINARY
Safety and General Information
i
Page 4
6881038B80.book Page ii Thursday, August 30, 2001 5:33 PM
• National Council on Radiation Protection and Measurements (NCRP) of the United States, Report 86, 1986
• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio
Frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999
• Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard 1999 (applicable to wireless phones only)
To assure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures:
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. DO NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects the effective range.
Two-Way Radio Operation
When using your radio as a traditional two-way radio, hold the radio in a vertical position with the microphone two to three inches (5. 0 to 7.5 cm) away from the lips.
Safety and General Information
ii
PRELIMINARY
Page 5
6881038B80.book Page iii Thursday, August 30, 2001 5:33 PM
Body-Worn Operation
To maintain compliance with FCC/Health Canada RF exposure guidelines, if you wear a radio on your body when transmitting, always place the radio in a Motorola
supplied or approved clip, holder, holster, case, or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC RF exposure guidelines. If you do not use a body-worn accessory, ensure the radio and its antenna is at least one inch (2.5 cm) from your body when transmitting. Data Operation
When using any data feature of a device, with or without an accessory cable, position the device and its antenna at least one inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories refer to the Two-Way Radio section of
www.motorola.com/store. Electromagnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.
Safety and General Information
PRELIMINARY
iii
Page 6
6881038B80.book Page iv Thursday, August 30, 2001 5:33 PM
Medical Devices
Pacemakers
The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 centimeters) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by, and recommendations of the U.S. Food and Drug Administration. Persons with pacemakers should:
• ALWAYS keep the radio more than six inches (15 centimeters) from their pacemaker when the radio is turned ON.
• not carry the radio in the breast pocket.
• use the ear opposite the pacemaker to minimize the potential for interference.
• turn the radio OFF immediately if you have any reason to suspect that
interference is taking place.
Hearing Aids
Some wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may
Safety and General Information
be able to assist you in obtaining this information.
iv
PRELIMINARY
Page 7
Safety and General Use While Driving
Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:
• Give full attention to driving and to the road.
• Use hands-free operation, if available.
• Pull off the road and park before making or answering a call if driving conditions
so require.
Operational Warnings
For Vehicles with an Air Bag
Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type especially qualified for use in such areas as “Intrinsically Safe.” Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Note: The areas with potentially explosive atmospheres referred to above include
fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted.
PRELIMINARY
Safety and General Information
v
Page 8
6881038B80.book Page vi Thursday, August 30, 2001 5:33 PM
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two­way radio.” Obey all signs and instructions.
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.
Charging Safety Instructions
Before using the battery charger, read all instructions and cautionary markings on:
1. the battery
2. the battery charger, and
3. the radio using the battery.
Caution: To reduce the risk of injury, charge only the rechargeable battery. Other types of batteries may burst, causing personal injury and damage.
Safety and General Information
vi
PRELIMINARY
Page 9
6881038B80.book Page vii Thursday, August 30, 2001 5:33 PM
Save these Instructions
1. Do not expose the charger to rain or snow.
2. Do not operate the charger if it has received a sharp blow, or has been dropped or damaged in any way.
3. Do not disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.
4. Never alter the AC cord or plug provided with the unit. If plug will not fit the out­let, have proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.
5. To reduce risk of damage to cord or plug, pull the plug rather than the cord when disconnecting charger from AC receptacle.
6. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.
7. Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock, or personal injury.
8. Make sure that the cord is located so that it will not be stepped on, tripped over, or subjected to damage or stress.
Safety and General Information
PRELIMINARY
vii
Page 10
6881038B80.book Page viii Thursday, August 30, 2001 5:33 PM
9. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure:
• That the pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.
• That the extension cord is properly wired and in good electrical condition, and
• That the cord size is18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.
10. The supply cord of this charger cannot be replaced. If the cord is damaged, call Motorola Product Services at:
1-800-353-2729 (U.S.A.) 1-800-461-4575 (Canada) 1-888-390-6456 TTY (Text Telephone) 1-888-390-6456 TTY (Text Telephone)
Safety and General Information
viii
PRELIMINARY
Page 11
6881038B80.book Page -1 Thursday, August 30, 2001 5:33 PM
Introduction
Thank you for purchasing a Motorola
Your radio is a product of Motorola’s 70 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The revised industrial design reflects the heritage and ruggedness of the XTN Series. The XTN Series radios provide cost­effective communications for businesses such as retail stores, restaurants, schools, construction sites and more. Motorola professional two-way radios are the perfect communications solution for all of today’s fast-paced industries.
Note: Please read this manual
Motorola Consumer Products Division 1705 Belle Meade Court Lawrenceville, GA 30043
XTN Series Radio.
carefully to ensure you know how to properly operate the radio before use.
PRELIMINARY
Package Contents
• Radio
• Swivel Belt Holster
• NiMH Battery NTN8971
• 10-Hour Charger NNTN4021
• User's Guide
• Accessory Brochure
• Warranty Card
Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are Trademarks of Motorola, Inc.
Reg. U.S. Pat. & Tm. Off. © 2001 Motorola, Inc. All rights reserved. Printed in the U.S.A. 08/01
For a copy of a large-print version of this guide, or for product-related questions, please contact:
1-800-353-2729 U.S.A. 1-800-461-4575 Canada 1-888-390-6456 TTY (Text Telephone)
On the web, please refer to: www.motorola.com/radios/professional
Introduction
-1
Page 12
Contents
Getting Started . . . . . . . . . . . . . . 3
Turning On/Off Your Radio . . . . . . . 3
Installing Batteries . . . . . . . . . . . . . . 4
Charging . . . . . . . . . . . . . . . . . . . . . 7
Programming Mode . . . . . . . . . . 9
Setting the
Channel . . . . . . . . . . . . . . . . . . . 10
Frequency . . . . . . . . . . . . . . . . . 10
Interference Eliminator Code . . . 11
Eavesdrop Reducer . . . . . . . . . . 11
Bandwidth . . . . . . . . . . . . . . . . . 12
Manager Lockout . . . . . . . . . . . . 12
Assigning Channels to Presets . . . 12
Cloning . . . . . . . . . . . . . . . . . . . . . . 13
Resetting Factory Defaults . . . . . . 13
Settings and Functions Display 14
Operating Radio . . . . . . . . . . . . 15
Signal Strength Indicator . . . . . . . . 15
Monitor Signal Strength Indicator . 15
ContentsContents
0
PRELIMINARY
User Menu Features . . . . . . . . 16
Setting Call Tone . . . . . . . . . . . . . 16
Setting Microphone Gain . . . . . . . . 16
Hands-Free Use/VOX . . . . . . . . . . 17
Setting Preferences for Scanning. . 19
Setting the Battery Type* . . . . . . . 20
End-of-Transmission Tone . . . . . . 20
Keypad Tones . . . . . . . . . . . . . . . . 21
Use and Care . . . . . . . . . . . . . . 22
Frequency and Code Charts . . 23
VHF Frequency Chart . . . . . . . . . . 23
UHF Frequency Chart . . . . . . . . . . 24
Interference Eliminator Codes . . . . 25
Digital Private Line/DPL Codes . . . 26
Troubleshooting . . . . . . . . . . . 27
Motorola Limited Warranty . . . 30
Page 13
FCC Licensing Information
XTN Series professional two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission (FCC). In order to transmit on these frequencies, you are required to have a license issued by the FCC.
Application is made on FCC Form 601 and Schedules D, E and G.
FCC
To have the FCC forms please request document 000601 and instructions. If you wish to have the document faxed, mailed or have questions, please use the following contact information.
contact the Fax-On-
Faxed
Demand system at:
1-202-418-0177
Before filling out your application, you must decide which frequency(ies) you can operate on. See the Frequency and Code Charts on page 23.
For questions on determining your radio frequency, please call Motorola Product Services at:
Mailed
call the FCC forms
hotline at:
1-800-418-FORM
1-800-418-3676
1-800-448-6686
which includes all forms
Questions
regarding FCC license
contact the FCC at:
1-888-CALL-FCC
1-888-225-5322
Or: http://www.fcc.gov
PRELIMINARY
FCC Licensing Information
1
Page 14
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform
FCC
transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed
FCC Licensing Information
2
is subject to government regulations and may be prohibited.
PRELIMINARY
Page 15
Getting Started
Turning On/Off Your Radio
Tur n
knob
P
Display Normal Menu Mode
Turn knob on the top of the radio clockwise to turn the radio On. Turn the Knob counterclockwise to turn the
k
1
radio Off. The radio chirps and the display will briefly show all
features and display segments of your radio.
Then, the code area will briefly display the current Channel (larger number located in the center of the display) and the Frequency assigned to that Channel.
The Interference Eliminator Code shows briefly. Current Channel will be left on display.
A Diagram of your New XTN Series Radio and its Functions can be found on page 8.
Volu me
You can set the volume by adjusting the knob on the top of the radio; P.
Note:
Do not hold the radio too close to your ear when the volume is at a high setting.
PRELIMINARY
Getting Started
X
3
Page 16
Installing Batteries
The Nickel-Metal Hydride Battery
• Push the Ribbed Latch on the bottom of the radio away from the battery door, or toward the contacts.
• Slide and lift the battery door off.
• Place the battery so that the charge
contacts are facing out toward the battery door. Insert the top of the battery into the radio and push the battery up and into the battery compartment. The battery fits tightly into place.
• Slide and snap the battery door into place.
Getting Started
Ribbed Latch
X
4
Note: *Based upon 5/5/90 duty cycle.
PRELIMINARY
Page 17
AA Alkaline Batteries
Your radio can also use 4 AA batteries; alkaline cells provide 24 hours* of radio use.
• Push the ribbed latch on the bottom of the radio away from the battery door.
• Slide and lift the battery door off.
• Place AA batteries matching the markings in
the compartment.
• Slide and snap the battery door into place.
Battery Meter
The battery meter located in the upper left hand corner of the display indicates how much battery power you have remaining.
Full Two-thirds Full One-third Full
Battery Meter flashes
when almost empty.
db c m
When the battery meter Flashes; m, the radio chirps after releasing Mand every
10 minutes.
Note: *Based upon 5/5/90 duty cycle.
PRELIMINARY
Getting Started
X
5
Page 18
Diagram of your New XTN Series Radio and its Functions
Indicator Light:
Use B to:
Transmit call tone
Use M to:
Ta lk
Exit a menu
Use \ button to:
Scroll through menus
Lock the keypad
Use T /
Getting Started
S buttons to:
Access Presets
(XU2600, XV2600)
Use P (Power) to:
Turn power On/Off Adjust radio volume
Accessory Jack
Audio Accessories Radio Plug-in Charging
Use J button to:
Turn Scan On/Off (XU2600, XV2600)
Monitor the Frequency
Use [ and ] to:
Change Channels (XU2600, XV2600) Scroll through menu settings
X
6
Microphone:
Speaker:
PRELIMINARY
Page 19
Charging
The NiMH Battery with 10-Hour Charger
• Make sure the radio is Off.
• Lift Accessory Cover and plug the 10-Hour
Charger (NNTN4021) firmly into the lower jack (small hole). Please see figure.
• Plug the charger into an electric outlet.
The light on the charger will glow red if charging properly. Note: Charge the battery (NTN8971)
overnight (16 hours) before using it for the first time, it will only need up to ten hours of charging thereafter.
For optimum battery life, the battery must not be left charging for prolonged periods after reaching full charge. Charging the battery over the weekend is acceptable.
If radio is On while charging, additional time is required to charge the battery.
Light
Getting Started
X
PRELIMINARY
7
Page 20
With Drop-in Charging Tray ( Not included with all models)
The Drop-in Charging Tray can be placed on any flat surface and provides drop-in charging convenience.
• Connect 10-Hour Charger (NNTN4021) and Drop-in Charging Tray* (NNTN4019) by inserting plug into the rear of Drop-in Charging Tray.
• To charge the radio, place into the Drop-in Charging Tray with the radio facing toward you.
Note: The battery can be charged while inside
the radio or removed from the radio and placed in Drop-in Charging Tray separately. The battery’s contacts must face down and the Motorola Logo must face the front of Charger.
The light on the 10-Hour Charger will glow continuously when radio/battery is inserted.
Note: Allow 10 hours for the battery to reach
Getting Started
* Accessory Number for Drop-in Charger is 53872.
X
full charge.
8
10-Hour Charger
NNTN4021
Drop-in
Charging Tray
NNTN401
PRELIMINARY
Page 21
Programming Mode
To talk with someone on your two-way radios, the following features need to be set exactly alike:
1. Channel
2. Frequency
3. Interference Eliminator Code providing you with a choice of code combinations.) Please refer to the Frequency and Code Charts on page 23.
4. Eavesdrop Reducer/Scrambling Code sound garbled to anyone listening who is not set to that specific code). Please refer to Setting Eavesdrop Reducer (2 watt models only) can be found on page 11.
Note: The Cloning Feature used with the Multi-unit Charger/MUC (Optional
Channel Frequency, Interference Eliminator Code, Eavesdrop Reducer/Scrambling
Code, and Manager Lock can all be selected in Programming Mode: k.
• Access k by turning the radio on while holding the M and J buttons for
three seconds.
• The Programming icon; k illuminates and radio chirps to indicate access.
• Exit k by holding the M for three seconds.
Note: k does not timeout.
(Current channel that the radio is using.)
(The frequency wave your radio uses to transmit/receive.)
(These codes help minimize interference by
(Codes that make your transmissions
Accessory) can help to duplicate radio settings easily for multiple radio use. Please refer to Cloning on page 13.
PRELIMINARY
k
Programming Mode
9
Page 22
6881038B80.book Page 10 Thursday, August 30, 2001 5:33 PM
Now, you may use your radio’s
k
k
Press Display Then Press
\
Setting the Channel (X2600 and XV2600 only)
• Make sure k is accessed. Please refer to Programming
• The channel number flashes. l and Code will display
• Press [ or ] until the desired channel is selected.
Setting the Frequency
• Press \ once, l indicator illuminates and the
• Press [ or ] to choose desired Frequency.
Programming Mode
• Exit the Programming Mode by holding down M.
10
the icon representing the feature you want
Mode on page 9.
alternately.
Frequency flashes.
\
and
or ] to select features.
[
[ or ] to select the feature.
Press
M for three seconds to exit
programming mode.
PRELIMINARY
6
Page 23
6881038B80.book Page 11 Thursday, August 30, 2001 5:33 PM
Setting the Interference Eliminator Code
The Interference Eliminator Code helps minimize interference by providing you with a choice of code combinations.
Make sure k is accessed. Please refer to Programming Mode on page 9.
• To set the code, press \ until the code number display begins
to flash.
• Then press [ or ] to choose the code.
Note: To hear everyone on your frequency, select Interference Eliminator Code 0.
Setting Eavesdrop Reducer (2 watt models only)
Your radio has the Eavesdrop Reducer feature, a scramble code that makes your transmissions sound garbled to anyone listening without the same code. It doesn’t guarantee confidentiality, but it adds an extra layer of privacy.
Note: All the radios have to be set to the same Eavesdrop Reducer for transmission
to be clear.
• Make sure k is accessed. Please refer to Programming Mode on page 9.
• Press \ as needed until e
• Press [ or ] to choose the scramble code.
•
Select code 1, 2, or
When you exit k, radio displays e.
3. Factory Default is set at 0 (Off).
is displayed, then
e
PRELIMINARY
k
Programming Mode
11
Page 24
6881038B80.book Page 12 Thursday, August 30, 2001 5:33 PM
Setting Bandwidth (when FCC allowable)
k
Make sure k is accessed. Please refer to Programming Mode on page 9.
k
• Change the setting by pushing the \ until ‘b’ displays.
• Press [ or ] to select setting:
Bandwidth is only selectable when flashing. Either "HI" (high: 25.0 kHz) or "Lo" (low: 12.5 kHz) will display.
Setting Manager Lockout
This feature aids in preventing changing of radio settings. All buttons except M and B, will be unaccessible when ‘Y’ is chosen.
• Make sure k is accessed. Please refer to Programming Mode on page 9.
• To turn lock on, press \ until f displays.
• Press [ or ] to select setting, ‘Y’ or ‘n.’
• Once turned on, f icon displays after exiting k.
Assigning Channels to Presets
• Make sure k is accessed. Please refer to Programming Mode on page 9.
• Press [ or ] to choose desired Channel.
• Press and hold T or S to assign a Channel to that preset button, radio beeps
Programming Mode
to confirm.
Note: All of the Channel settings are assigned to that preset button.
C
K
n
12
PRELIMINARY
Page 25
6881038B80.book Page 13 Thursday, August 30, 2001 5:33 PM
Cloning
The XTN Series radios have cloning capability when connected via the Multi Unit Charger (MUC). Cloning enables rapid fleet reconfiguration because all selectable settings are sent to the target unit. The target radios must be placed behind the source radio, please refer to the MUC instructions included with this accessory.
• Make sure k is accessed. Please refer to Programming
Mode on page 9.
• The source radio enters Cloning Mode through an extended
press of J. Pressing J again, will clone additional radios.
• Either p for pass or f for fail shall appear on the display.
• Only the source radio needs to be in Clone Mode, and both
radios will indicate if cloning was successful.
Resetting Factory Defaults
All selectable features can be reset to factory defaults by turning the radio on while
holding M and \ buttons simultaneously for five seconds.
Note: The radio cannot be reset if Manager Lockout is enabled.
PRELIMINARY
k
Programming Mode
13
Page 26
6881038B80.book Page 14 Thursday, August 30, 2001 5:33 PM
Settings and Functions Display
k
k
Scan
Battery Meter
Manager Lockout/User Lock
Eavesdrop Reducer Signal Strength
Programming Mode
Channel
The following table lists the functions you can set by pressing and holding a button while you are turning on your radio.
Frequency Setting and
Interference Eliminator Code
Frequency Indicator
VOX
Key(s) Pressed. Function
Access k Programming Mode: Five second delay.
You can change the channel here. Reset factory settings: Five second delay.
+
)
Will not work if Manager Lock is enabled.
Enable g VOX.
Tu r ns “End-of-Transmission Tone On/Off. Radio default setting is “Off.”
Turns Keypad Tones On/Off. Radio default setting is “On.”
14
J P = k
M
M
\
M
P
Settings and Functions Display
]
P
[
P
P +
PRELIMINARY
Page 27
6881038B80.book Page 15 Thursday, August 30, 2001 5:33 PM
Operating Radio
Check channel activity by pressing monitor button. You will hear static if the channel is clear to use. Do not transmit if someone is speaking on the channel.
• Press and hold M. and speak into radio.
Note: To maximize clarity hold radio two-to-three inches away from mouth.)
• To listen for messages, release M.
Note: The transmit light on the front left of the radio flashes every three seconds
Signal Strength Indicator
Monitor Signal Strength Indicator
To check for channel activity, press and hold the J button. You’ll hear static if the channel is clear and w 0 will display. Press J to release. To avoid interrupted conversation, wait until the channel
is clear or switch to another channel. Note: Obstacles that block the signal path may affect the strength of the incoming
when radio is On and is steady red when transmitting.
The radio will display w when there is activity on the frequency. When receiving the display will show w and a signal strength of
1 (weakest) through 6 (strongest) .
radio is moving out of range.
signal.
This can help to determine when a
Operating Radio
X
PRELIMINARY
15
Page 28
6881038B80.book Page 16 Thursday, August 30, 2001 5:33 PM
User Menu Features
Setting Call Tone
Your radio can transmit call tones to other radios in your group so you can alert the group that you want to talk to them. There are three distinct individual call tones to
choose or you can choose to turn Call Tones off: 0. Once selected, just press
transmit the Call Tone to others.
• To set your call tone, press
• You can press [ or ] to scroll through the available call tones.
The radio plays each individual Call tone as you scroll through.
as needed to display E.
\
B
to
User Menu Features
X
16
Note: The default is set on 0, or you may choose 1
Setting Microphone Gain
Microphone Gain allows compensation for background noise and enhances the ability to pick up quiet voices.
• To set sensitivity level, press \ as needed, until g and ? are
visible.
• Select 1, 2 or 3 by using 3 = High Sensitivity
2 = Medium Sensitivity 1 = Low Sensitivity
[
or ]:
, 2, or
3.
PRELIMINARY
?
Page 29
6881038B80.book Page 17 Thursday, August 30, 2001 5:33 PM
Hands-Free Use/VOX
VOX allows “hands-free” transmission when used with compatible VOX
• Turn radio Off.
• Open Accessory Cover.
• Insert plug of audio accessory firmly into Accessory Jack.
• Turn radio On and lower volume before placing accessory
on head or in ear.
• To transmit, speak into Accessory Microphone and to receive, stop talking.
Setting VOX Sensitivity Level
The default VOX sensitivity level must be changed for initial
use. The g will flash if sensitivity is set to 0.
• Press
• Select Sensitivity Level of 1, 2, or 3 by using
or ]:
[ 3 = High Sensitivity 2 = Medium Sensitivity 1 = Low Sensitivity
as needed to display g and H.
\
accessories.
User Menu Features
X
PRELIMINARY
17
Page 30
6881038B80.book Page 18 Thursday, August 30, 2001 5:33 PM
Note: To order accessories, please refer to: www.motorola.com/
radios/professional.
• VOX operation can be disabled by pressing M.
• A short press M of will enable VOX.
XU2600 and XV2600 radios are capable of hands-free use without accessories.
• Enable VOX by pressing M as needed to display g and I.
\
M will enable VOX.
User Menu Features
X
• Press
Setting VOX Sensitivity Level
• Select Sensitivity Level of 1, 2, or 3 by using
or ]:
[ 3 = High Sensitivity 2 = Medium Sensitivity 1 = Low Sensitivity
To turn VOX Off, simply turn the radio Off and then On again. The g will not be visible. Press M to turn off VOX and return to normal operation, g will flash.
A short press of Note: There is a short delay between when you start talking and the radio
transmits.
18
H
3
while turning the radio On.
PRELIMINARY
Page 31
6881038B80.book Page 19 Thursday, August 30, 2001 5:33 PM
Setting Preferences for Scanning/Scan List
By using J, you can monitor channels and codes for transmissions and lock in on
a specific channel.
• To start scanning, briefly press J. Your channel/code screen displays h and begins to scroll through channels. When
the radio detects channel activity, it stops on that channel and displays its channel and code. You can talk to the person(s) transmitting without having to switch channels by pressing
• To stop scanning, briefly press J. If you press
which was selected before you activated Scan. If no transmission occurs within five seconds, scanning will resume. If you want to scan channels without interference eliminator codes, change the code
for your set channel to 0 before you briefly press J.
Nuisance Delete/ Manual Advance While Scanning
Note: While scanning you can quickly delete a channel that the radio has loaded for
.
M
while the radio is scanning, the radio will transmit on the channel
M
an indefinite period of time by pressing Editing. You can also advance to the next channel with activity by manually pressing
].
[ once, i.e. shortcut to Scan List
User Menu Features
X
PRELIMINARY
19
Page 32
6881038B80.book Page 20 Thursday, August 30, 2001 5:33 PM
Editing Scan List
Scan List Setting is changed by pressing the \ button three times.
• The flashing channel will appear on the display with a solid
code section.
• Press [ or ] button to increase or decrease the channel.
• Pressing the Js button toggles between the channel number and Scan List
setting.
• The scroll buttons, [ or ] will change the Scan List to include/
that particular channel.
• Once you have seklected your Scan List options, press
Setting the Battery Type*
This feature allows the battery meter to recognize and properly display the power remaining of single cell batteries.
Press \ until d displays. Either A (Alkaline) or n (NiCad,
NiMH, Li-Ion rechargeable AA cells) is flashing.
• Press [ or ] until your choice of A or n displays.
Note: *This menu will not appear if the NiMH Battery is in use.
User Menu Features
End-of-Transmission Tone
X
When you turn this feature On, your two-way radio transmits a tone when you finish transmitting. It’s like saying “Roger” or “Over.”
20
Y or n in the
to exit.
M
Y or exclude/n
A
PRELIMINARY
Page 33
6881038B80.book Page 21 Thursday, August 30, 2001 5:33 PM
• If you don’t hear the talk confirmation tone, you can enable it by pressing and
holding ] as you turn on your radio.
• To disable the End-of-Transmission Tone feature, turn your radio Off and then
back On while pressing and holding ].
Keypad Tones
Every time you press a button on your radio, it beeps unless you turn this feature off.
• Turn your radio On while you press and hold
• To turn Keypad Tones back on, turn the radio Off and then back On again while
you press and hold [.
Talking Range
Industrial Multi-Level Outdoor
Inside steel/concrete
Model
UHF 2W Up to 250, 000 Sq. Ft. Up to 20 Floors Up to 6 Miles
UHF 1W Up to 200, 000 Sq. Ft. Up to 15 Floors Up to 5 Miles
VHF 2W Up to 180, 000 Sq. Ft. Up to 10 Floors Up to 6 Miles
VHF 1W Up to 150,000 Sq. Ft. Up to 8 Floors Up to 5 Miles
industrial buildings
Inside multi-level
buildings
[
.
Flat ground with no
obstructions
User Menu Features
X
PRELIMINARY
21
Page 34
XXX
6881038B80.book Page 22 Thursday, August 30, 2001 5:33 PM
Use and Care
XXX
Use and Care
X
22
Use a soft damp cloth
to clean the exterior.
If the radio gets wet...
Turn radio Off and
remove batteries.
PRELIMINARY
Do not immerse
in water.
Dry with soft cloth.
Do not use alcohol or
cleaning solutions.
Do not use radio until
completely dry.
Page 35
6881038B80.book Page 23 Thursday, August 30, 2001 5:33 PM
Frequency and Code Charts
The charts on these pages provide frequency and code information. These charts are useful when using Motorola XTN Series two-way radios with other business radios.
VHF Frequency Chart
Position MHz Bandwidth Position MHz Bandwidth
1 151.6250 25.00 16 151.8650 25.00 2 151.9550 25.00 17 151.8950 25.00 3 154.5700 25.00 4 154.6000 25.00 19 152.7000 25.00 5 151.7000 12.5/25.0 6 151.7600 12.5/25.0 21 154.5150 25.00 7 151.8200* 12.5/25.0 8 151.8800* 12.5/25.0 23 154.5400 25.00
9 151.9400* 12.5/25.0 10 151.5125 25.00 25 154.6550 25.00 11 151.6550 25.00 12 151.6850 25.00 27 158.4075 25.00 13 151.7150 25.00 14 151.7450 25.00 15 151.7750 25.00
18 151.9250 25.00
20 154.4900 25.00
22 154.5275 25.00
24 154.6000 25.00
26 158.4000 25.00
Note: Due to FCC regulations,
these frequencies transmit at 1 watt only.
PRELIMINARY
Frequency and Code Charts
X
23
Page 36
6881038B80.book Page 24 Thursday, August 30, 2001 5:33 PM
Position MHz Bandwidth Position MHz Bandwidth
1 464.5000 12.5/25.0 29 462.9125 12.5 2 464.5500 12.5/25.0 30 464.4875 12.5 3 467.7625 12.5 4 467.8125 12.5 32 464.5375 12.5 5 467.8500 12.5/25.0 6 467.8750 12.5/25.0 34 466.0375 12.5 7 467.9000 12.5/25.0 8 467.9250 12.5/25.0 36 466.0875 12.5
9 461.0375 12.5 10 461.0625 12.5 38 466.1375 12.5 11 461.0875 12.5 12 461.1125 12.5 40 466.1875 12.5 13 461.1375 12.5 14 461.1625 12.5 42 466.2375 12.5 15 461.1875 12.5 16 461.2125 12.5 44 466.2875 12.5 17 461.2375 12.5 18 461.2625 12.5 46 466.3375 12.5 19 461.2875 12.5 20 461.3125 12.5 48 467.7875 12.5 21 461.3375 12.5 22 461.3625 12.5 50 467.8625 12.5
Frequency and Code Charts
X
24
23 462.7625 12.5 24 462.7875 12.5 52 467.9125 12.5 25 462.8125 12.5 26 462.8375 12.5 54 469.5125 12.5 27 462.8625 12.5 28 462.8875 12.5 56 469.5625 12.5
UHF Frequency Chart
31 464.5125 12.5
33 464.5625 12.5
35 466.0625 12.5
37 466.1125 12.5
39 466.1625 12.5
41 466.2125 12.5
43 466.2625 12.5
45 466.3125 12.5
47 466.3625 12.5
49 467.8375 12.5
51 467.8875 12.5
53 469.4875 12.5
55 469.5375 12.5
PRELIMINARY
Page 37
6881038B80.book Page 25 Thursday, August 30, 2001 5:33 PM
Interference Eliminator Codes
This allows you to monitor all activity on the channel you are using. Interference Eliminator codes help minimize interference by providing you with a choice of code combinations.
Code Hz Code Hz Code Hz
1 67.0 14 107.2 27 167.9
2 71.9 15 110.9 28 173.8
3 74.4 16 114.8 29 179.9
4 77.0 17 118.8 30 186.2
5 79.7 18 123.0 31 192.8
6 82.5 19 127.3 32 203.5
7 85.4 20 131.8 33 210.7
8 88.5 21 136.5 34 218.1
9 91.5 22 141.3 35 225.7
10 94.8 23 146.2 36 233.6
11 97.4 24 151.4 37 241.8
12 100.0 25 156.7 38 250.3
13 103.5 26 162.2
Carrier Squelch (0) disables Interfeence Eliminator Codes.
PRELIMINARY
Frequency and Code Charts
X
25
Page 38
6881038B80.book Page 26 Thursday, August 30, 2001 5:33 PM
Digital Private Line/DPL Codes
Position Code Word Position Code Word Position Code Word
39 023 67 174 95 445 40 0256820596 464 41 026 42 0317022698 466 43 032 44 04372244100 506 45 047 46 05174251102 532 47 054 48 06576263104 565 49 071 50 07278271106 612 51 073 52 07480311108 627 53 114 54 11582331110 632 55 116 56 12584346112 662 57 131 58 13286364114 703 59 134
Frequency and Code Charts
X
26
60 14388371116 723 61 152 62 15590412118 732 63 156 64 16292423120 743 65 165 66 17294432
69 223 97 465
71 243 99 503
73 245 101 516
75 261 103 546
77 265 105 606
79 306 107 624
81 315 109 631
83 343 111 654
85 351 113 664
87 365 115 712
89 411 117 731
91 413 119 734
93 431 121 754
PRELIMINARY
Page 39
6881038B80.book Page 27 Thursday, August 30, 2001 5:33 PM
Troubleshooting
Symptom Try Thi s:
No Power
Message not transmitted
Hearing other noises or conversation on a channel
Message scrambled
Limited talk range
PRELIMINARY
Recharge or replace battery (NTN8971). Reposition or replace AA batteries.
Make sure M is completely pressed as you transmit.
Replace, recharge and/or reposition batteries.
Confirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use,
change code on all radios if possible.
Eavesdrop Reducer is on, and/or setting does not match other radios’ settings.
Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission.
Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio.
Troubleshooting
X
27
Page 40
6881038B80.book Page 28 Thursday, August 30, 2001 5:33 PM
Symptom Try This:
Confirm radios have the same channel, frequency, interference eliminator code and *eavesdrop reducer code settings. (*XV2600, XU2600)
Message not received
Make sure M
Replace, recharge and/or reposition batteries. Obstructions and operating indoors, or in vehicles, may interfere
-- change location. Verify that the radio is not in Scan mode.
is NOT being pressed while trying to listen.
Troubleshooting
X
28
Heavy static or interference
Keypad locked
Low batteries
PRELIMINARY
Radios are too close, they must be at least five feet apart. Radios are too far apart or obstacles are interfering with
transmission.
Make sure menu is unlocked. Unlock by holding \ for three
seconds. Make sure Manager Lockout is disabled. Please refer to Setting
Manager Lockout on page 12.
Recharge or replace NiMH battery. Replace AA batteries. Extreme operating temperatures affect battery life.
Page 41
6881038B80.book Page 29 Thursday, August 30, 2001 5:33 PM
Symptom Try Thi s:
Charger light does not come on.
Low battery meter reading although new batteries are installed
Cannot activate VOX
PRELIMINARY
Check radio/battery is properly inserted and check battery/ charger contacts to be sure they are clean.
Verify that the radio is set to the correct battery type. (Single cell bateries only.)
Feature not set and on.Sensitivity set to 0.
Please refer to Hands-Free Use/VOX on page 17.
Troubleshooting
X
29
Page 42
6881038B80.book Page 30 Thursday, August 30, 2001 5:33 PM
Motorola Limited Warranty
Personal Communications Products Purchased in the United States and Canada
V. What This Warranty Covers
• Products. Defects in materials and workmanship in wireless cellular telephones, pagers, and/or two-way radios, and certain accessories that are sold with them, such as the battery, battery charger and holster manufactured and/or sold by Motorola (Products).
• Batteries. Defects in materials and workmanship in batteries that are manufactured by Motorola and/or sold with Products are covered by this warranty only if the fully-charged capacity falls below 80% of rated capacity or they leak.
• Software. Physical defects in the media that tangibly embodies each copy of any software supplied with the Products.
VI. What the Period of Coverage Is
From the date the Products are purchased by the first end-user:
• Products. The warranty is for one year. Exception: The warranty for Spirit GT series and Talkabout series two-way radio accessories is for 90 days.
• Software. The warranty is for 90 days.
• Repairs / Replacements. The warranty is for the balance of the original warranty or for 90
days from the date you receive it, whichever is longer.
VII. Who is Covered
This warranty extends to the first end-user purchaser, only.
Motorola Limited Warranty
X
30
PRELIMINARY
Page 43
6881038B80.book Page 31 Thursday, August 30, 2001 5:33 PM
VIII. What We Will Do to Correct Warranty Problems
At no charge to you, we have the option to repair or replace the Products or software that do not conform to the warranty, or to refund the Products’ purchase price. We may use functionally equivalent reconditioned/refurbished/pre-owned or new Products or parts. No software updates are provided.
IX. How to Get Warranty Service
Please call: USA Canada
Cellular 1-800-331-6456 All Products1-800-461-4575 Paging 1-800-548-9954 TTY 1-888-390-6456 (Text Telephone) Two-Way 1-800-353-2729 TTY 1-888-390-6456 (Text Telephone)
You will receive instructions on how to ship the Products to Motorola. You must ship the Products to us with freight, duties and insurance prepaid. Along with the Products you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider (if this Product requires subscription service); (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number. If requested, you must also return all detachable parts such as antennas, batteries and chargers. RETAIN YOUR ORIGINAL PROOF OF PURCHASE. We will ship repaired or replacement Products at our expense for the freight and insurance, but at your expense for any duties. If additional information is needed, please contact us at the telephone number listed above.
PRELIMINARY
Motorola Limited Warranty
X
31
Page 44
6881038B80.book Page 32 Thursday, August 30, 2001 5:33 PM
X. What This Warranty Does Not Cover
• Products that are operated in combination with ancillary or peripheral equipment or software not furnished by Motorola for use with the Products (“ancillary equipment”), or any damage to the Products or ancillary equipment as a result of such use. Among other things, “ancillary equipment” includes batteries, chargers, adaptors, and power supplies not manufactured or supplied by Motorola. Any of these voids the warranty.
• Someone other than Motorola (or its authorized service centers) tests, adjusts, installs, maintains, alters, modifies or services the Products in any way. Any of these voids the warranty.
• Rechargeable batteries that: (a) are charged by other than the Motorola-approved battery charger specified for charging such batteries; (b) have any broken seals or show evidence of tampering; (c) are used in equipment other than the Product for which they are specified; or (d) are charged and stored at temperatures greater than 60 degrees centigrade. Any of these voids the warranty.
• Products that have: (a) serial numbers or date tags that have been removed, altered or obliterated; (b) board serial numbers that do not match each other, or board serial numbers that do not match the housing; or (c) nonconforming or non-Motorola housings or parts. Any of these voids the warranty.
• Defects or damage that result from: (a) use of the Products in a manner that is not normal or customary; (b) improper operation or misuse; (c) accident or neglect such as dropping the Products onto hard surfaces; (d) contact with water, rain, extreme humidity or heavy perspiration; (e) contact with sand, dirt or the like; or (f) contact with extreme heat, or spills of food or liquid.
• Physical damage to the surface of the Products, including scratches, cracks or other
Motorola Limited Warranty
damage to a display screen, lens or other externally exposed parts.
X
• Failure of Products that is due primarily to any communication service or signal you may subscribe to or use with the Products.
• Coil cords that are stretched or that have any broken modular tabs.
32
• Products that are leased.
PRELIMINARY
Page 45
6881038B80.book Page 33 Thursday, August 30, 2001 5:33 PM
Flat-rate repair rates may apply to Products not covered by this warranty. To obtain information about Products needing repairs that are not covered by this warranty, please call the telephone number previously listed. We will provide information on repair availability, rates, methods of payment, where to send the Products, etc.
XI. Some Other Limitations
This is Motorola’s complete warranty for the Products, and states your exclusive remedies. This warranty is given in lieu of all other express warranties. Implied warranties, including without limitation, the implied warranties of merchantability and fitness for a particular purpose, are given only if specifically required by applicable law. Otherwise, they are specifically excluded. No warranty is made as to coverage, availability, or grade of service provided by the Products, whether through a service provider or otherwise. No warranty is made that the software will meet your requirements or will work in combination with any hardware or applications software products provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. In no event shall Motorola be liable, whether in contract or tort (including negligence) for damages in excess of the purchase price of the Product, or for any indirect, incidental, special or consequential damages of any kind, or loss of revenue or profits, loss of business, loss of information or data, or other financial loss arising out of or in connection with the ability or inability to use the Products, to the full extent these damages may be disclaimed by law.
Motorola Limited Warranty
X
PRELIMINARY
33
Page 46
6881038B80.book Page 34 Thursday, August 30, 2001 5:33 PM
XII. Patent and Software Provisions
At Motorola’s expense, we will defend you, and pay costs and damages that may be finally awarded against you, to the extent that a lawsuit is based on a claim that the Products directly infringe a United States patent. Our obligation is conditioned on: (a) you notifying us promptly in writing when you receive notice of the claim; (b) you giving us sole control of the defense of the suit and all negotiations for its settlement or compromise; and (c) should the Products become, or in Motorola's opinion be likely to become, the subject of a claim of infringement of a United States patent, you permit us, at our option and expense, either to: procure for you the right to continue using the Products; replace or modify them so that they become non-infringing; or grant you a credit for such Products, as depreciated, and accept their return. The depreciation will be an equal amount per year over the lifetime of the Products, as established by Motorola. Motorola will have no liability to you with respect to any claim of patent infringement that is based upon the combination of the Products or parts furnished under this limited warranty with ancillary equipment, as defined in VI., above. This is Motorola’s entire liability with respect to infringement of patents by the Products. Laws in the United States and other countries preserve for Motorola and other third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to reproduce in copies and distribute copies of such software. The
Motorola Limited Warranty
software may be copied into, used in and redistributed with only those Products that are associated with such software. No other use, including without limitation,
X
disassembly or reverse engineering of such software or exercise of exclusive rights in such software is permitted.
34
PRELIMINARY
Page 47
6881038B80.book Page 35 Thursday, August 30, 2001 5:33 PM
XIII. State Law and Other Jurisdiction Rights
Some states and other jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction. To obtain information on Motorola Personal Communications Products, including warranty service, accessories and optional Extended Warranties on selected Products, please call: USA Canada
Cellular 1-800-331-6456 All Products1-800-461-4575 Paging 1-800-548-9954 TTY 1-888-390-6456 (Text Telephone) Two-Way 1-800-353-2729 TTY 1-888-390-6456 (Text Telephone)
To correspond with Motorola about the Products, please write us at http://www.motorola.com or at: In the USA: In Canada:
Motorola, Inc. Motorola Canada Limited 600 North U.S. Highway 45 5875 Whittle Road Libertyville, IL 60048 Mississauga, ON L4Z 2H4
Page 48
6881038B80.book Page 36 Thursday, August 30, 2001 5:33 PM
Software Copyright Notice
The Motorola products described in this manual may include copyrighted Motorola and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law. Furthermore, the purchase of the Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Patent Notice
This product is covered by one or more of the following United States patents. 5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758 D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745 D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252 D416893 D433001
Page 49
6881038B80.book Page 37 Thursday, August 30, 2001 5:33 PM
Export Law Assurances
This product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and International Trade.
Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
More specifically, changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed
is subject to government regulations and may be prohibited.
Page 50
6881038B80.book Page 38 Thursday, August 30, 2001 5:33 PM
Page 51
6881038B80.book Page 55 Thursday, August 30, 2001 5:33 PM
Index A
Accessory ..................................................18
Cover.....................................................6
Adjust volume ...............................................6
Alkaline batteries ..........................................5
B
Back cover ....................................................4
Bandwidth...................................................12
Battery
Alkaline ..................................................5
Install ..............................................5
Charge
NTN8971NiMH...............................7
Meter .....................................................5
NTN8971NiMH
Charge............................................7
Install ..............................................4
Optimum life ..........................................7
Setting .................................................20
Button Beeps ..............................................14
C
Call display .................................................16
Call tone...................................................6,16
Channel ................................................3,9,14
Activity .................................................15
Change..................................................6
Monitor.................................................19
Setting .................................................10
Charger .........................................................7
Desktop Drop-in.....................................8
Multi-unit ................................................9
Plug-in....................................................8
Charging .......................................................7
Clean radio..................................................22
Cloning.....................................................9,13
Code
Interference Eliminator......................9,11
Scrambling.............................................9
D
Default
Settings................................................13
Diagram
Function .................................................6
Drop-in Charger ............................................8
E
Eavesdrop Reducer ....................................11
Exit a menu ...................................................6
F
FCC
FAX
1-202-418-0177 ..............................1
FORMS
1-800-418-3676 ..............................1
1-800-418-FORM ...........................1
QUESTIONS
1-888-225-5322 ..............................1
1-888-CALL-FCC............................1
Page 52
6881038B80.book Page 56 Thursday, August 30, 2001 5:33 PM
UHF Bandwidth ...................................12
FCC Licensing Information ...........................1
Frequency.....................................................3
Setting .................................................10
Functions ......................................................6
G
Gain ............................................................16
H
Hands-Free Use .........................................17
I
Icon Programming ........................................9
Indicator Light
...............................................................6
Install
AA Battery .............................................5
NTN8971NiMH Battery.......................... 4
Interference Eliminator Code...................9,11
Internal VOX ...............................................18
L
Licensing Information
FCC .......................................................1
Light
Charger..................................................7
Desktop Charger ...................................8
Radio indicator.....................................15
Lock
keypad ...................................................6
M
Meter
Battery ...................................................5
Mic Gain......................................................16
Microphone ...................................................6
Monitor Signal Strength ..............................15
MOTOROLA SERVICES
1-800-448-6686 .....................................1
N
noise ...........................................................16
NTN8971NiMH battery..................................4
O
Obstacle......................................................15
Operating radio ...........................................15
Optional Accessory
www.motorola.com/spirit........................9
P
Plug
Audio....................................................17
Plug-in Charger.............................................7
Programming Mode ................10,11,12,13,14
R
Radio
Back cover .............................................5
Bottom ...................................................4
Clean ...................................................22
Diagram .................................................6
Display ...................................................5
Factory default settings........................13
Features...............................................16
Frequency wave/Channel ......................9
Page 53
6881038B80.book Page 57 Thursday, August 30, 2001 5:33 PM
Functions and Settings ........................ 14
Latch......................................................4
Off..........................................................3
On........................................................14
Operating.............................................21
Out of range.........................................15
Radio Display................................................3
Range
Talking.................................................21
Roger Beeps...............................................14
S
Scan............................................................28
Turn On/Off............................................6
Scan List.....................................................19
Scrambling Code ........................................11
Sensitivity level ...........................................17
Setting
Battery Type ........................................20
Call tone ..............................................16
Channel ...............................................10
Factory Defaults ..................................13
Interference Eliminator Code............... 11
Scrambling Code.................................11
Volume ..................................................3
Setting VOX Sensitivity Level ...............17, 18
Signal Strength Indicator ............................15
Speaker ........................................................6
T
Talk Confirmation Tone ..............................20
Talking range ..............................................21
To talk ...........................................................6
Transmit ......................................................18
U
Use and Care..............................................22
V
Volume
Adjust.....................................................6
VOX .......................................................14,17
External................................................17
Off ........................................................18
W
Website
Motorola
www.motorola.com
Accesories
www.motorola.com/radios/professional
FCC
www.fcc.gov .........................................1
Page 54
6881038B80.book Page 67 Thursday, August 30, 2001 5:33 PM
Function Appearance
Channel
Frequency
Interference Eliminator Code
XTN-Series Quick Reference
[
or
Use
XU2600, XV2600
] for
1 through 6*
Eavesdrop Reducer
Battery Meter
Channel Scan
XU2600, XV2600
Receiving
Visible if Feature is On.
Visible except when changing features.
Press J to access.
Others speaking on the same frequency and code.
6
Signal strength 1-6
Page 55
6881038B80.book Page 68 Thursday, August 30, 2001 5:33 PM
XTN Series User Programming
Radio On
Call Tone
Mic Gain/ Sensitivity Level
Scan List
*Battery Type
Lock Keypad
XTN Series Buttons
• Turn power on/off M
P
T
• Access Preset Channel
S
• Transmit call tone
B
Visual \as needed, then
?
A
*XU2600, XV2600 only
Choose1,2,3 or Off = 0
Choose1 low, 2 medium, or 3 high sensitivity.
Choose Y (yes) or n (no) for each
individual channel.
*XU2600, XV2600 only
A (alkaline) n (other rechargeable single cells)
Does not appear if using NiMH.
Hold \for 3 seconds
no flashing
\
[
or ]• Scroll through settings.
[
or
]
• Talk on the radio
• Exit a menu
• Scroll through menus
• Lock Keypad 3 seconds
Page 56
Page 57
6881038B80.book Page 2 Thursday, August 30, 2001 5:33 PM
• Extend Your Productivity
Provides a cost-effective solution to onsite communication needs. Designed for heavy duty, everyday industrial use. Well suited for construction, manufacturing, security, property management, retail, etc.
• Rugged MOTOROLA QUALITY
Shock/drop/temperature tested to meet Motorola's High standards.
• Weather/Dust Resistant
IP-54 rating
• Built to Military Specifications
810 C, D, E & F
• Dependable Indoor/Outdoor Coverage
Will provide a communication range* of up to 250,000 sq. ft. or 20 floors indoors and up to 6 miles outdoors. *Range will vary based on terrain and conditions and model selected.
• Accessories for XTN Series - Brochure included Convenient headphones, multi-chargers, drop-in chargers, carry cases, and rechargeable battery packs available from your retailer or www.motorola.com
MOTOROLA, the Stylized M Logo, XTN Series and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. © 2001 Motorola, Inc. All rights reserved. Printed in the U.S.A.
Motorola® XTN Series
@xtnseries@
Proof of Purchase
• Simple and Easy to Operate
Allows one-to-one or group communication at the push of a button. With no phone numbers to dial, plus the manager lock feature, there's little to no training needed for your staff to be fully up to speed.
• Cost Efficient
No monthly fees to pay and no service contracts. Compatible with older Motorola Spirit• radios and audio accessories.
• User Guide Included
Radio Specification Chart
Tr an s mi t Po w er Receiver Sensitivity Audio Putput Receiver Technology
/sradios/professional
FCC
License required.
• Business Exclusive Frequencies
Frequencies set aside exclusively for business-only use (FCC License required).
• 38 PL Codes, 83 Digital PL Codes.
• Talk Hands-Free Mode (VOX)
Advanced voice activation (VOX) let's you talk hands-free; XV2600, XU2600 models do not require accessories.
• Voice Compression Technology
Helps provide better sound even at longer distances.
• Cloning Capability
1 or 2 Watts
-120 dBm for 12 dB SINAD 90 dB SPL Direct Conversion
PWARNING CHOKING HAZARD
SMALL PARTS
Not for children under 3 years.
This product is not intended to be used
as a toy or plaything.
Page 58
3
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use