Motorline professional BRAVO500 User Manual
v4.0
REV. 04/2018
EN
USER'S AND INSTALLER'S MANUAL
EN
BRAVO500
2A 2B
2B
13A
13B
4A
4B
6A
12
5A
6A
7B
10B
9A
12
5B
7A
10A
8A
11
ENEN
INDEX
STANDARDS TO FOLLOW
00. CONTENT 01. SAFETY INSTRUCTIONS
STANDARDS TO FOLLOW
SCHEMES FOR CAPACITORS
MAINTENANCE
INSIDE PACKAGE
OPEN COVER
INSTALLATION SITE PREPARATION
FINAL CONSUMERS INSTRUCTIONS
UNLOCK OPERATOR
SITE INSTALLATION – CREATE FOUNDATION
APPLICATION OF MOTOR
CLUTCH ADJUSTMENT
INSTALLATION OF NYLON GEAR RACK
SPECIALIZED TECHNICIANS INSTRUCTIONS
TECHNICAL SPECIFICATIONS
SITE INSTALLATION – EXISTING FOUNDATION
INSTALLATION OF PLATES THE LIMIT SWITCHES
INSTALLATION OF STEEL GEAR RACK
MAP OF INSTALLATION
01. SAFETY INSTRUCTIONS
06. COMPONENTS TEST
07. MAINTENANCE
02. PACKAGE
03. OPERATOR
04. INSTALLATION
05. TROUBLESHOOTING
This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed of
as other household waste at the end of its useful life. To avoid
possible harm to the environment or human health resulting
from the uncontrolled disposal of waste, separate these items
from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Home
users should contact the dealer where they purchased this
product or the National Environment Agency for details on
where and how they can take these items for environmentally
safe recycling. Business users should contact their vendor and
check the terms and conditions of the purchase agreement.
This product and its electronic accessories should not be
mixed with other commercial waste.
This marking indicates that the product and electronic accessories
(eg. charger, USB cable, electronic material, controls, etc.) are
susceptible to electric shock by direct or indirect contact with
electricity. Be cautious when handling the product and observe
all safety procedures in this manual.
ENEN
3A 3B
ENEN
STANDARDS TO FOLLOWSTANDARDS TO FOLLOW
01. SAFETY INSTRUCTIONS01. SAFETY INSTRUCTIONS
ENEN
automated is in good mechanical condition, correctly balanced and opens
and closes properly.
• If the automation is to be installed at a level higher than 2,5 m above
ground level or other level of access, , should be followed the minimum
safety and health requirements for the use of work equipment workers
at work in Directive 2009/104/EC of the European Parliament and of the
Council of 16th September of 2009.
• In the case of the equipment where the automation will be installed, have
a pedestrian door, be aware that it must be closed when the automation is
activated.
• After installation, make sure that the mechanism is properly adjusted and
that the protection system and any manual unlocker works correctly.
• In order to protect the electrical cables against mechanical stress, you
should use conduit for the electrical wires, essentially on the power cable.
• When programming the control unit, pay particular attention to touching
only the location intended for that purpose. Failure to do so may result in
electric shock.
• It is important for your safety that these instructions are followed.
• Keep these instructions in a safe place for future reference.
• The ELECTROCELOS S.A. is not responsible for the improper use of the
product, or other use than that for which it was designed.
• The ELECTROCELOS S.A. is not responsible if safety standards were not
taken into account when installing the equipment, or for any deformation
that may occur.
• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction
of the product when used with components that were not sold by the them.
• This product was designed and manufactured strictly for the use indicated
in this manual.
• Any other use not expressly indicated may damage the product and/or can
cause physical and property damages, and will void the warranty.
• Do not make any changes to the automation components and/or their
accessories.
• Keep remote controls away from children, to prevent the automated system
from being activated involuntarily.
• The customer shall not, under any circumstances, attempt to repair or tune
the automatism. Must call qualified technician only.
• The installer must have certified professional knowledge at the level of
mechanical assemblies in doors and gates and control board programmation.
He should also be able to perform electrical connections in compliance
with all applicable regulations.
• The installer should inform the customer how to handle the product in an
emergency and provide him the manual.
• This device can be used by children 8 year old or older and persons whose
physical, sensory or mental capacities are reduced, or by persons without
experience or knowledge if they have received supervision or instructions on
the use of the device in a safe manner and understood the hazards involved.
Children should not play with the device. Cleaning and maintenance by the
user must not be carried out by unsupervised children.
• Before installing, the installer must verify that the temperature range
indicated on the automatism is appropriate to the location of the installation.
• Before installing, the installer must verify that the equipment to be
4A 4B
385mm
226mm
380mm
01
04
05
A
A
A
03
02
02•
11•
10•
09•
04•
05•
03•
01•
08•
06•
07•
ENEN
Inside the package you will find the following components:
02. PACKAGE
INSIDE PACKAGE
01• 01 motor Bravo500
02• 02 release keys
03• 04 screws DIN912 M5x10
04• 04 fixing screws to the plate
05• 04 fixing screws to the ground
06• 01 fixation plate
07• 02 fixation plate of the limit switches
08• 01 user's manual
09• 02 photocells
10• 02 remote controls
11• 01 Control board
OPEN COVER
03. OPERATOR
During installation you will need
to open the motor cover, to access
various components on the inside. For
this, loosen the 2 screws identified
with (A) until the cover is free to be
removed.
Electronic components of the kit:
ENEN
Loading...