Motorline TELICA User Manual

V2.1

REV. 02/2019

TELICA

EN

USER’S AND INSTALLER’S MANUAL

A B

1B

3A

3B

4A

4A

6A

7A

8A

6B

7B

9B

3B

4B

4B

5A

5A

5B

ENEN

STANDARDS TO FOLLOW

INSIDE THE PACKAGE

DIMENSIONS

EMERGENCY UNLOCK

INSTRUCTIONS FOR FINAL CONSUMERS
INSTRUCTIONS FOR SPECIALIZED INSTALLERS

TECHNICAL SPECIFICATIONS

INSTALLATION MEASURES
SUPPORTS INSTALLATION

. SAFETY INSTRUCTIONS

. THE PACKAGE

. OPERATOR

. INSTALLATION

. TROUBLESHOOTING

. CONTENT . SAFETY INSTRUCTIONS

INDEX STANDARDS TO FOLLOW

AUTOMATISM INSTALLATION
ARMS INSTALLATION
MICROS ADJUSTMENT

Vac MOTOR
Vdc MOTOR

. COMPONENTS TEST

EXTERNAL UNLOCK

. CONNECTION SCHEME

ATTENTION:

This product is certified in accordance with European Community
(EC) safety standards.

This product complies with Directive 2011/65/EU of the European
Parliament and of the Council, of 8 June 2011, on the restriction
of the use of certain hazardous substances in electrical and
electronic equipment.

(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed of
as other household waste at the end of its useful life. To avoid
possible harm to the environment or human health resulting
from the uncontrolled disposal of waste, separate these items
from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources. Home users
should contact the dealer where they purchased this product or
the National Environment Agency for details on where and how
they can take these items for environmentally safe recycling.
Business users should contact their vendor and check the terms
and conditions of the purchase agreement. This product and its
electronic accessories should not be mixed with other commercial
waste.

This marking indicates that the product and electronic accessories
(eg. charger, USB cable, electronic material, controls, etc.) are
susceptible to electric shock by direct or indirect contact with
electricity. Be cautious when handling the product and observe all
safety procedures in this manual.

V/V MOTOR (MC)
V MOTOR (MC)

A B

ENEN

. SAFETY INSTRUCTIONS. SAFETY INSTRUCTIONS

STANDARDS TO FOLLOWSTANDARDS TO FOLLOW

properly.

• If the automation is to be installed at a level higher than 2,5 m above ground
level or other level of access, , should be followed the minimum safety and
health requirements for the use of work equipment workers at work in Directive
2009/104/EC of the European Parliament and of the Council of 16th September
of 2009.

• In the case of the equipment where the automation will be installed, have
a pedestrian door, be aware that it must be closed when the automation is
activated.

• After installation, make sure that the mechanism is properly adjusted and that
the protection system and any manual unlocker works correctly.

• In order to protect the electrical cables against mechanical stress, you should
use conduit for the electrical wires, essentially on the power cable.

• When programming the control unit on the control board, you should pay
particular attention to touching only the location intended for that purpose.
Failure to do so may result in electric shock.

• It is important for your safety that these instructions are followed.

• Keep these instructions in a safe place for future reference.

• The ELECTROCELOS S.A. is not responsible for the improper use of the product,
or other use than that for which it was designed.

• The ELECTROCELOS S.A. is not responsible if safety standards were not taken
into account when installing the equipment, or for any deformation that may
occur.

• The ELECTROCELOS S.A. is not responsible for insecurity and malfunction of the
product when used with components that were not sold by the them.

• This product was designed and manufactured strictly for the use indicated in
this manual.

• Any other use not expressly indicated may damage the product and/or can
cause physical and property damages, and will void the warranty.

• Do not make any changes to the automation components and/or their
accessories.

• Keep remote controls away from children, to prevent the automated system
from being activated involuntarily.

• The customer shall not, under any circumstances, attempt to repair or tune the
automatism. Must call qualified technician only.

• The installer must have certified professional knowledge at the level of
mechanical assemblies in doors and gates and control board programmation.
He should also be able to perform electrical connections in compliance with all
applicable regulations.

• The installer should inform the customer how to handle the product in an
emergency and provide him the manual.

• This device can be used by children 8 year old or older and persons whose
physical, sensory or mental capacities are reduced, or by persons without
experience or knowledge if they have received supervision or instructions on
the use of the device in a safe manner and understood the hazards involved.
Children should not play with the device. Cleaning and maintenance by the user
must not be carried out by unsupervised children.

• Automatism powered by very low safety voltage, with electronic board / control
board / control unit. (24 Vdc)

• Before installing, the installer must verify that the temperature range indicated
on the automatism is appropriate to the location of the installation.

• Before installing, the installer must verify that the equipment to be automated
is in good mechanical condition, correctly balanced and opens and closes