Motorline TEC 1 User Manual And Installer Manual

v1.1

REV. 05/2015

TEC 1

• Note that automatic gate and door systems must be installed exclusively by qualified technical
personnel in full compliance with statutory legislation.

• Before starting the installation procedure check that the values given in the "Technical
Specifications” chapter are compatible with the application.

• This product has been designed to control door openers, gate openers and similar mechanisms.
Any other use of the product will be considered improper.

This is a dual channel transmitter that is activated only after having entered a suitable
combination.
The units are designed for installation in indoor or outdoor locations. That ensures the utmost
security because the transmitted code is changed at each transmission session.
The estimated transmission range is 200 m in open space and 35 m indoors.
The units are designed to ensure battery life equivalent to an estimated 2 years of operation
considering 10 transmissions per day.

Audible signal Status

1 short beep Keypad tone

1 long beep Auto power-off

3 long beeps Modification of combination confirmed

5 short beeps Error during combination input or combination edit operation

10 rapid beeps Battery low warning signal New batteries required

Before physically installing the unit it is good practice to perform a practical test to assess their
functionality and effective range.
Consider that range may be up to 25 or 30% less when battery power is low.

Apart from the distance from the receiver, the units should not be positioned in the vicinity or in
contact with metal structures, which could otherwise exert a signal shielding effect. Thanks to
the enclosure protection rating of IP 54, the digital selectors can be installed outdoors if required.

INSTALLATION

WARNINGS

POSITIONING

USER MANUAL/INSTALLER

EN

• Table A changing the combination associated with channel 1 (◄)

This function allows you to change the combination associated with channel 1 (◄):

1 • Press the "0" key and hold it down while pressing and releasing “◄”;
2 • Release the “0” and “◄” keys;
3 • Type in the current (original) combination and press “◄” (Original - 11, or the code that was

being used);

4 • Type in the new combination (up to 8 digits ) pressing “◄”;
5 • Type in the new combination again and press “◄” (the keyboard will emit one long beep

confirming the operation's sucess. If it emits several beeps, repeat the operation).

• Table B changing the combination associated with channel 2 (►)

This function allows you to change the combination associated with channel 2 (►):

1 • Press the "0" key and hold it down while pressing and releasing “►”;
2 • Release the “0” e "►" keys;
3 • Type in the current (original) combination and press “►” (Original - 22, or the code that was

being used);

4 • Type in the new combination (up to 8 digits ) and press “►”;
5 • Type in the new combination again and press “►” (the keyboard will emit one long beep

confirming the operation's sucess. If it emits several beeps, repeat the operation).

Table C normal use for activation of channel 1

1 • Type in the combination associated with channel 1;
2 • Press “◄”.

Table D normal use for activation of channel 2

1 • Type in the combination associated with channel 2;
2 • Press “►”.

To reset the keyboard, it must be sent to our technical services.

The use of the keypad is based on "combinations", i.e. numbers of from 1 to 9 digits that the user
is required to key in by means of the keys. Once the combination has been entered the user then
presses confirm key ◄or► , to transmit the activation command to, respectively:

• receiver channel 1 if the user presses ◄

• receiver channel 2 if the user presses ►

The command will be transmitted only when a valid combination has been entered: if an incorrect
combination has been entered the selector will emit an error, warning signal when the confirm
key is pressed . The combination entered must be exact, if, for example ,the correct combination
is 0422, the following attempts will be interpreted as errors: 422, 10422, 04222. Therefore, if the
user inadvertently presses the wrong key when entering a combination, combination key ◄ or ►
should be pressed immediately to generate the error tone , after which the correct combination
can be entered starting from the beginning again.
While entering the combination no more than 6 seconds can be allowed to elapse between
keystrokes, after which interval the combination must be re-entered starting from the beginning.
The units are factory programmed with a standard combination to activate channel one and a
standard combination for channel two.

The factory set combinations are as follows:

• When the unit is used for the first time this combination is 11 ◄

• When the unit is used for the first time this combination is 22 ►

CHANGING A COMBINATION

NORMAL USE

RESET THE UNIT TO FACTORY SETTINGS

METHOD OF USE

If combinations are set without entering any number, the security system is
effectively overridden and the command can be transmitted simply by pressing

◄or ► without having to first enter a combination.

If the two combinations you have entered are identical, once you have entered the
combination you can press either “◄” or “►”.