Motorline 800A, OL2000, OL1500 Operating And Installation Instructions
AUTOMATION SYSTEMS FOR SLIDING GATES
Operating and installation instructions
English
v1.0
Rev 11/2012
SLIDE SERIES
INDEX
1) General Safety Regulations
2) Description
3) Technical Specications
4) System Description
5) Accessories
6) Installation Tools
7) Installation
8) Maintenance
9) Repairs
................................................................................................................... pág. 01
.................................................................................................................................................. pág. 02
......................................................................................................................... pág. 03
................................................................................................................................. pág. 03
................................................................................................................................................. pág. 04
....................................................................................................................................... pág. 04
.................................................................................................................................................. pág. 05
............................................................................................................................................... pág. 10
.......................................................................................................................................................... pág. 10
1) ATTENTION! To ensure the safety of people, it is important that you read all the following instructions.
Incorrect installation or incorrect use of the product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of children as such materials
are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this documentation. Any other
use, not expressly indicated here, could compromise the good condition/operation of the product
and/or be a source of danger.
6) Manufacturer / distributor decline all liability caused by improper use or use other than that for which
the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of inammable gas or fumes
is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604 and EN12605. For
non-EU countries, to obtain an adequate level of safety, the Standards mentioned above must be
observed, in addition to national legal regulations.
9) We are not responsible for failure to observe Good Technique in the construction of the closing
elements to be motorised, or for any deformation that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445.
11) Before attempting any job on the system, cut electrical power.
12) Make sure that the earthing system is perfectly constructed, and connect metal parts of the means
of the closure to it.
13) The automated system force control. Nevertheless, its tripping threshold must be checked as
specied in the Standards indicated at point 10.
14) The safety devices (EN 12978 standard) protect any danger areas against mechanical movement
risks, such as crushing, dragging, and shearing.
15) Use of at least one indicator-light is recommended for every system, as well as a warning sign
adequately secured to the frame structure.
16) Manufacturer / distributor decline all liability as concerns safety and ecient operation of the
automated system, if system components not produced by them.
17) For maintenance, strictly use original parts by us.
18) Do not in any way modify the components of the automated system.
19) The installer shall supply all information concerning manual operation of the system in case of an
emergency, and shall hand over to the user the warnings handbook supplied with the product.
20) Do not allow children or adults to stay near the product while it is operating.
21) Keep remote controls or other pulse generators away from children, to prevent the automated
system from being activated involuntarily.
22) Transit is allowed only when the gate is fully open.
23) The user must not attempt any kind of repair or direct action whatever and contact
qualied personnel only.
24) Anything not expressly specied in these instructions is not permitted.
1) GENERAL SAFETY REGULATIONS
Pág. 01
Automated system for residential or industrial sliding gates with a maximum of 2000kgs.
It consists of a reversing electro-mechanical gearmotor, powered by a 230V control unit.
The automated system houses a programmable electronic control board that enables setting of
function logics, work time and pause time, anti-crushing sensitivity as well as partial-opening width.
The reversing system guarantees the gate will automatically lock when the motor is not operating.
A release system enables the gate to be moved by hand in case of malfunction or emergency.
The automated system was designed and built for controlling sliding gates. Do not use for any
other purpose.
1. Gate
2. Rack spacer
3. Protective cover
4. Foundation plate
5. Fixation screw
Fig. 01
Fig. 02
Fig. 03
6. Control box
7. Motor
8. Cover
9. Rack
10. Housing
11. Lock
12. Manual release
13. Capacitor
14. Screw
15. Limit switch plate
2) DESCRIPTION
2.1. Description of the structure
2.2. Dimensions (mm)
Pág. 02
342
276
165
36
6
15
7 8
9
14
11
12
5
4
3
2
1
10
13
201,5
274,7
344
162,5
210
Loading...