Motomaster 011-2064-0 User Manual

WARNING

Table of Contents

IMPORTANT SAFETY WARNINGS..................................................1

KEY PARTS DIAGRAM...................................................................6

Screen Display...........................................................................7

OPERATION...................................................................................8

Jump Starting...........................................................................10

Low Voltage Batteries & Manual Override..............................12

Recharging...............................................................................13

Operate As 12 V Power Supply................................................14

Operate Air Compressor..........................................................15

LED Light..................................................................................17

USB Power...............................................................................17

TROUBLE SHOOTING...................................................................18

TECHNICAL SPECIFICATIONS.....................................................20

ENVIRONMENTAL PROTECTION.................................................21

WARRANTY.................................................................................21

SAVE THESE INSTRUCTIONS!

This manual contains important safety and operating instructions. Read all instructions and follow them.

DO NOT RETURN THIS PRODUCT TO THE STORE! QUESTIONS? CALL CUSTOMER SERVICE, HOTLINE:1-888-942-6686

READ AND UNDERSTAND ALL SAFETY INFORMATION BEFORE USING THIS PRODUCT. Failure to follow these safety instructions may result in ELECTRICAL SHOCK, EXPLOSION OR FIRE, which may result in a SERIOUS INJURY, DEATH, or PROPERTY DAMAGE.

Electrical Shock. Product is an electrical device that can shock and cause serious injury. Do not cut power cords. Do not submerge in water or get wet.

Explosion. Unmonitored, incompatible, or damaged batteries can explode if used with product. Do not leave product unattended while in use. Do not attempt to jump start a damaged or frozen battery. Use product only with

IMPORTANT SAFETY WARNINGS

batteries of recommended voltage. Operate product in well ventilated areas.

Fire. Product is an electrical device that emits heat and is capable of causing burns. Do not cover product. Do not smoke or use any source of electrical spark of re when operating product. Keep product away from combustible materials.

Eye injury. Wear eye protection when operating product. Batteries can explode and cause eye and skin irritation. In the case of contamination of eyes or skin, ush affected area with running clean water and contact poison control centre immediately.

Explosive Gases. Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. To reduce risk of battery explosion, follow all safety information instructions and those published by the battery manufacturer and manufacturer of any equipment intended to be used in the vicinity of battery. Review cautionary markings on these products and on engine.

Important Safety Warnings

Personal Precaution. Only use product as intended. Someone should be within range of your voice or close enough to come to your aid in case of emergency. Have a supply of clean water and soap nearby in the case of battery acid contamination. Wear complete eye protection and protective clothing while working near a battery. Always wash hands after handling batteries and related materials. Do not handle or wear any metal objects when working with batteries including: tools, watches or jewellery. If metal is dropped onto battery, it may spark or create a short circuit resulting in electrical shock, re, explosion which may result in injury, death or property damage.

Choking Hazard. Accessories may present a choking hazard to children. Do not leave children unattended with product or any accessory. The product is not a toy.

IMPORTANT SAFETY WARNINGS

Handling. Handle product with care. The product can become damaged if

impacted. Do not use a damaged product, including, but not limited to, cracks to the casing or damaged cables. Do not use product with a damaged power cord. Humidity and liquids may damage product. Do not handle product or any electrical components near any liquid. Store and operate product in dry locations. Do not operate product if it becomes wet. If product is already operating and becomes wet, disconnect it from the battery and discontinue use immediately. Do not disconnect the product by pulling on the cables.

Modications. Do not attempt to alter, modify or repair any part of product. Disassembling product may cause injury, death or damage to property. If product becomes damaged, malfunctions or comes in contact with any liquid, discontinue use. Any modications to the product will void your warranty.

Accessories. This product is only approved for use with MotoMaster accessories. MotoMaster is not responsible for user safety or damage when using accessories not approved by MotoMaster.

Location. Prevent battery acid from coming in contact with the product. Do not operate the product in a closed-in area or an area with restricted ventilation. Do not set a battery on top of product. Position cable leads to avoid accidental damage by moving vehicle parts (including hoods and doors), moving engine parts (including fan blades, belts, and pulleys), or what could become a hazard that may cause injury or death.

Operation Temperature. This product is designed to work in ambient temperatures between -30°C to 60°C (-22°F to 140°F). Do not operate outside of temperature range. Do not jump start a frozen battery. Discontinue use of product immediately if the battery becomes excessively warm.

Storage. Do not use or store your product in areas with high concentrations of dust or airborne materials. Store your product on at, secure surfaces so it's not prone to falling. Store your product in a dry location. The storage temperature is

-20°C to 25°C (-4°F to 77°F) (average temperature). Never exceed 80°C (176°F) under any condition.

Compatibility. The product is only compatible with 12-volt lead-acid batteries only. Do not attempt to use product with any other type of battery. Jump starting other battery chemistries may result in injury, death or property damage. Contact the battery manufacturer prior to attempting to jump start the battery. Do not jump start a battery if you are unsure of the battery's specic chemistry or voltage.

Medical Devices. Product may emit electromagnetic elds. Product contains magnetic components which may interfere with pacemakers, debrillators, or other medical devices. These electromagnetic elds may interfere with pacemakers or other medical devices. Consult with your physician prior to use if you have any medical devices including pacemakers. If you suspect the product is interfering with a medical device, stop using the product immediately and consult your physician.

Medical Conditions. If you have any medical conditions that you believe could be affected by product, including but not limited to: seizures, blackouts, eyestrain or headaches, consult your physician prior to use of product.

Cleaning. Power off the product before attempting any maintenance or cleaning. Clean and dry product immediately if it comes in contact with liquid or any type of contaminant. Use a soft, lint-free (microbre) cloth. Avoid getting moisture in openings.

Explosive Atmospheres. Obey all signs and instructions. Do not operate product in any area with a potentially explosive atmosphere, including fueling areas or areas which contain chemicals or particles such as grain, dust or metal powders.

High-consequence Activities. This product is not intended for use where the failure of the product could lead to injury, death or severe environmental damage.

The battery. The built-in lithium-ion battery in the product must be recycled or disposed of separately from household waste. Don't attempt to replace the battery yourself and do not handle a damaged or leaking lithium-ion battery. Never dispose of battery in household trash. Disposal of batteries in household trash is unlawful under provincial environmental laws and regulations. Always take used batteries to an your local battery recycling centre. If the product battery is excessively hot, emitting odour, deformed, cut, or is experiencing or demonstrating an abnormal occurrence, immediately stop all use.

IMPORTANT SAFETY WARNINGS

Battery Charging. Charge the product with the included USB charge cable and

10 W 12 V Car Charger. A third party USB cable and 5 W or 10 W Car Charger that may be compatible. Be cautious of using low quality power adaptors, as they may present a serious electrical risk that can result in injury to person, device and property.

Using damaged cables or chargers, or charging when moisture is present, can result in electric shock. Using generic or third party power adaptor may shorten the life of your product and cause the product to malfunction. MotoMaster is not responsible for the user's safety when using accessories that are not approved by MotoMaster.

When using a AC plug to charge the product, make sure that the AC plug is fully inserted into the adaptor before you plug it into a power outlet. It may become warm during normal use, and prolonged skin contact may cause bodily injury. Always allow adequate ventilation around power adaptors when using them.

To ensure maximum battery life, avoid charging your product for more than a week at a time, as overcharging may shorten battery life. Over time, an unused product will discharge and must be recharged before use. Disconnect the product from power sources when not in use. Use the product only for its intended purposes.

High Temperature Protection

During Charging

The normal charging temperature range for the internal battery is 0ºC to 45ºC. If the battery temperature exceeds 45ºC, the icon will appear on the display and the unit will stop charging. The unit will resume charging once the battery cools below 45ºC.

During Use

The normal operating temperature range for the internal battery is 0ºC to 60ºC. If the battery temperature exceeds 60ºC, the icon will appear on the display and unit functions will be inoperable. The unit will resume functions once the battery cools below 50ºC.

Over-temperature Damage

If the battery temperature exceeds 80ºC, both the and icons will appear on the display and the unit functions will be inoperable. If, after cooling down, the icon disappears but the icon remains, the internal battery has been permanently damaged from being exposed to excessive heat. Immediately stop all use of the product.

KEY PARTS DIAGRAM

12V

IMPORTANT SAFETY WARNINGS

KEY PARTS DIAGRAM

4 5

Psi

126

–

Screen Display

Internal Battery Voltage

Battery Status Icon

OPERATION

WARNING! EQUIPMENT DAMAGE

Compressor Pressure Indicator

Jump Starter Icon

Caution Icon

Connection Indicator

1. Main Power Button

2. 12 V DC Power Button

3. 12 V DC Power Outlet (under protective cover)

4. 90º Adjustable LED Light

5. Digital Display

6. Pressure Setting Button (+/-)

7. Air Compressor Power Button

8. LED Light Button

9. Boosting Power Button

10. USB Ports (x2) (under protective cover)

11. Air Compressor Nozzle Connector

12. Boosting Clamps

13. USB Charging Port (under protective cover)

14. Boosting Clamps Connection Port (under protective cover)

15. USB Charging Cable

16. USB 12 V Car Charger Adaptor

17. Ball/Balloon Adaptors

Psi

USB 5 V

Overheat Icon

126

USB Icon

KEY PARTS DIAGRAM

Warm-up Mode Icon

• Do not crank the engine for more than 3 seconds at a time. The jump start feature is designed for short term operation only. Operating the jump start feature for more than 3 seconds may cause damage to the unit. Do not attempt more than 5 consecutive jump starts within a 15 minute period. Allow the product to rest for 15 minutes before attempting to jump start the vehicle again.

• Risk of shock, re, combustion, and burns, do not disassemble, modify,

crush, heat above 60ºC (140ºF) or incinerate.

OPERATION

IMPORTANT!

• Before attempting to boost vehicle.

• Verify that you have a 12 volt lead-acid battery.

• Turn off vehicle ignition and all accessories; ensure vehicle is in “park” and emergency brake is engaged.

• Make sure the BOOSTING POWER SWITCH is in the “OFF” position.

• Do not attempt to jump start an engine if the battery level is at 50% or less.

• Do not place the unit where it could fall when vehicle starts up.

• Make sure that cables are routed away from motor fan or belts.

GETTING STARTED

This product comes partially charged and needs to be fully charged prior to use. Carefully read and understand the vehicle owner's manual on specic precautions and recommended methods for jump starting the vehicle. Make sure to determine the voltage and chemistry of the battery by referring to your battery owner's manual prior to using this product. This product is for jump starting 12 volt lead acid batteries only.

Warm-up Mode

This product is designed with an innovative self-heating feature which will warm up the internal lithium-ion battery, improving performance in sub-zero temperatures. When the unit is powered ON, if the internal battery temperature is below 0ºC, the icon will appear on the display indicating that unit is in Warm-up mode. During warm-up, functions such as jump starting and air compressor are inoperable – you must wait until warm-up is complete to use these functions. Once the icon disappears, the unit is ready for use. Depending on temperature, warm-up can take anywhere from a few seconds up to 10 minutes.

OPERATION

JUMP STARTING

Warning! Instructions are for negative ground systems only (most common for vehicles today). If your vehicle is a positive ground system, reverse steps 3 and 4. Please consult your vehicle’s manual to conrm your vehicle’s ground system.

1. Firmly insert the booster clamps into boosting clamps connection port.

2. Press to turn the unit on.

3. Connect the red clamp to the POS (+) terminal of the vehicle battery.

4. Connect the black clamp to the NEG (-) terminal of the vehicle battery.

5. Check battery level indicator. If less than 3 bars, recharge the unit

OPERATION

before attempting a jump start.

6. Check display status and proceed as per instructions below.

–

Proceed as per A, B or C

Psi

6. Press to begin jump starting.

The unit will count down for 5 seconds.

Psi

12 Volt

126

7. Try starting the vehicle. Most vehicles will immediately start. Some vehicles may require the unit to be connected for up to 30 seconds before starting. If the vehicle does not start right away, wait 20-30 seconds between attempts.

CAUTION: Do not attempt more than 5 consecutive jump starts within a 15 minute period. Allow the product to rest for 15 minutes before attempting to jump start the vehicle again.

8. Once your vehicle starts, disconnect the battery clamps and remove the jump starter.

126

Psi

126

Psi

126

Psi

（alarm）

The unit has detected a good connection with a battery. Proceed to Step 6.

Battery clamps are connected to the opposite terminals. Reverse clamp connections before proceeding to Step 6.

The unit cannot detect a connection. Reconnect the clamps and ensure proper contact with the battery terminals. If connection indicator is still blank, see Low Voltage Batteries/Manual Override section.

Psi

The icon appears and a countdown begins. You have 50 seconds to jump start your vehicle.

OPERATION

Low Voltage Batteries & Manual Override

The unit is designed to jump start 12 Volt lead-acid batteries down to 2 volts. If your battery is below 2 volts, the display will be off. This is an indicator that the unit can not detect a battery. If you need to jump start a battery below 2 volts, this unit has an OVERRIDE feature, which allows you to force 'ON' the jump start function.

CAUTION: Use this mode with extreme care. This mode is for 12 volt lead-acid batteries only. Both the spark-proof and reverse polarity protection feature are disabled. Pay very close attention to the polarity of the battery before using this mode. DO NOT allow the positive and negative battery

OPERATION

clamps to touch or connect to each other as the product will generate sparks. This mode uses very high current (up to 1000 Amps) that can cause sparks and high heat if not used properly. If you are unsure about using this mode, do not attempt and seek professional help.

WARNING! Before using the OVERRIDE mode, ensure the clamps are connected to the correct polarity (red clamps to POS + terminal of the battery and black clamp to the NEG – terminal of the battery).

1. Press and hold for a few seconds until the icon appears on the display.

Psi

The unit will count down for 5 seconds.

Psi

The icon appears and a countdown begins. You have 50 seconds to jump start your vehicle.

2. Try starting the vehicle. Most vehicles will immediately start. Some vehicles may require the unit to be connected for up to 30 seconds before starting. If the vehicle does not start right away, wait 20-30 seconds between attempts.

CAUTION: Do not attempt more than 5 consecutive jump starts within a 15 minute period. Allow the product to rest for 15 minutes before attempting to jump start the vehicle again.

3. Once your vehicle starts, press to turn the unit off and then disconnect the clamps from the battery terminals.

CAUTION: Power the product off before disconnecting the battery clamps. This will ensure your safety. Remember both the spark-proof and reverse polarity protection features are disabled.

RECHARGING

IMPORTANT!

• Improper charging may result in damage to the unit.

• Ensure that there are no 12 V DC appliances connected to the unit while

being recharged.

• Do not operate any of this unit’s functions while charging is in progress.

• Do not recharge the unit while connected to an external battery.

• Recharge battery after each use or at least every 6 months when in storage

to prolong battery life and keep the unit ready for use.

1. Open protective ap to expose USB charging port.

2. Connect micro USB cable to the unit’s USB charging port.

3. Connect the other end of the micro USB cable to any powered USB power port such as a laptop, 12 V DC adaptor (included) or AC charging cube (not included).

The USB port is rated at 2.4 Amps to ensure safe and efcient charging of the internal lithium-ion battery. We recommend that you do not charge and discharge the unit at same time.

OPERATION

The battery level indicator will light up and the bars will ash on/off to indicate that the unit is charging. The bars indicate the state of charge of the internal battery. See below:

The internal battery is at 25%. The internal battery is at 75%.

The internal battery is at 50%.

CHECK BATTERY STATUS

Press the button, the Battery Level Indicator LEDs will illuminate to indicate battery charge level.

Psi

126

OPERATE AS 12V POWER SUPPLY

IMPORTANT! DO NOT use this unit to operate appliances that need more than

12 A to operate from the 12 V DC power port.

This unit is equipped with one DC outlet socket and can be used to power most 12 volt accessories and appliances.

1. Pull open cover of the 12 V DC Power Port on the side of the unit.

2. Insert the 12 V DC plug from the appliance into the 12 V DC Power port on the unit.

3. Press to turn the unit on.

4. Press to activate the DC power outlet.

The internal battery is at 100%.

15 17

OPERATE AIR COMPRESSOR

CAUTION! EQUIPMENT DAMAGE

• DO NOT operate air compressor continuously for longer than 10 minutes.

• Allow compressor to cool down for every 10 minutes of continuous use.

• DO NOT use this product for other than its intended use.

CAUTION! BURST HAZARD AND INJURY

• Carefully follow instructions and recommended pressure of products being inated. DO NOT OVER INFLATE.

• Always wear eye protection when operating the air compressor.

• DO NOT leave the compressor unattended during use.

IMPORTANT!

• The Air Compressor operates from the internal battery of the unit. Check battery condition to make sure it is satisfactory before operating compressor. DO NOT use compressor function if battery is less than 50%.

• The product records the latest pre-set pressure. For example, if your pre-set

pressure is 35 PSI, the product records the pre-set pressure at 35 PSI for the next time. Always check pre-set pressure before activating compressor function.

• Before reaching desired pressure, the compressor can be shut off manually by pressing the compressor switch.

• Recharge unit after each use.

This product is equipped with 150 PSI auto shut-off digital pressure gauge that can be used to inate tires, sports equipment and other recreational inatables. The digital gauge can be used to monitor air pressure when inating your products, and can automatically shut off once pre-set desired pressure is reached.

OPERATION

1. Roll-out the Air Compressor Nozzle Connector on the side of the unit.

2. a) For inating tires or other objects with valve stems, screw in the nozzle connector to the valve stem.

b) For inating sporting equipment, party balloons or other objects without

valve stems, screw in the appropriate adaptor into the nozzle connector and insert it into the object being inated.

3. Press to turn the unit on.

4. Press and hold or for a few seconds until the compressor pressure

indicator starts to icker. Adjust to desired pressure ( to increase pressure and to decrease pressure).

5. Release or once desired pressure is reached. The PSI reading will

ash a few times then go to 0 PSI. This means the pre-set pressure was successfully recorded by the unit.

6. Press to operate the compressor. Unit will automatically shut-off once

desired pre-set pressure is reached.

7. Once unit has nished inating, press to turn the unit off.

8. Unscrew the nozzle connector from the valve stem of the object being

inated. If using an adaptor, disconnect from object being inated and remove adaptor from nozzle connector.

9. Store air hose and ball/balloon adaptors in the appropriate storage

compartments.

LED LIGHT

IMPORTANT! Make sure LED light is OFF when unit is being recharged or stored.

1. Press to turn unit on.

2. Press to turn the LED light on.

3. Press again to turn the LED light off.

The light is adjustable 90°.

USB POWER

IMPORTANT! Make sure there are no devices plugged in to the USB power port

when unit is being recharged or stored.

The unit is equipped with a USB port with a 5 V 2.4 A power output. This port is ideal for charging portable electronic devices such as smartphones, tablets and more.

1. Lift protective cover labelled “USB” to expose USB ports.

2. Connect device(s) to USB port(s).

3. Press to turn unit on and activate USB power.

4.The display will show “USB 5 V” indicating the USB power is on.

Psi

126

USB 5 V

OPERATION

TROUBLESHOOTING

Problem

Unit will not charge

The engine being boosted will not start

Air compressor will not work

12 V DC Power function does not work

USB Power port does not work

Note: If the above solutions do not eliminate the problem, contact 1-888-942-6686 for assistance.

Possible Cause Solution

• No power from USB port

• Faulty USB cable

• Power draw during recharge

• Faulty status LED reading

• Main power is OFF

• Vehicle battery is too low

• Unit is not fully charged

• Bad clamp connection with battery

• Vehicle battery is damaged

• Mechanical issue with vehicle

• Battery in the unit is damaged

• Main power is OFF

• Unit is not fully charged

• Nozzle connector or inating adaptor not connected properly

• Compressor has overheated

• Faulty air compressor

• Main power is OFF

• Unit has insufcient charge to power appliance

• Appliance draw exceeds rating

• Main power is OFF

• Unit has insufcient charge to power appliance

• Incompatible device

• Plug in to a different USB outlet

• Replace USB cable

• Disconnect all accessories plugged into the unit and make sure all of the unit functions are off

• Disconnect charger and allow unit to rest for 15 minutes. Reconnect and check battery status

• Press to turn unit ON (refer to JUMP STARTING instructions)

• Override feature needs to be used (refer to LOW VOLTAGE BATTERIES & MANUAL OVERRIDE instructions)

• Check if unit has at least 75% charge. Recharge if necessary

• Reconnect clamps and ensure proper contact and polarity has been established

• Replace vehicle battery

• Have the vehicle serviced

• Replace unit

• Press to turn unit ON (refer to OPERATING AIR COMPRESSOR instructions)

• Check if unit has at least 75% charge. Recharge if necessary

• Make sure nozzle connector is securely screwed on to the valve stem if inating tires; or nozzle adaptor is securely connected to nozzle connector and object being inated

• Turn Air Compressor switch to the “OFF” position. Let unit cool down for 10 minutes

• Replace unit

• Press to turn unit ON (refer to OPERATE AS 12 V POWER SUPPLY instructions)

• Check unit battery charge level. Recharge if necessary

• Use appliance with a max draw of 12 A

• Press to turn unit ON

• Check unit battery charge level. Recharge if necessary

• Check if device is compatible with this USB type/port

TECHNICAL SPECIFICATIONS

Internal Battery Lithium-Ion

Internal Battery Capacity 9000 mAh

Peak Current Rating 1000 A

Operating Temperature

Storage Temperature

Micro USB Input 5 V, 2.1 A

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

USB Output 5 V, 2.4 A (total)

12 V DC Output 12 A max

Air Compressor 150 PSI

Dimensions

Weight

-30°C ~ 60°C (-22°F to 140°F)

-20°C ~ 25°C (-4°F to 77°F)

22.5 × 18.5 × 8.6 cm (8 7/8 x 7 1/4 x 3 3/8")

2 kg (4 lb 7 oz)

ENVIRONMENTAL PROTECTION

Do not dispose of this product in the usual household garbage at the end of its life cycle; hand it over at a collection point for the recycling of electrical and electronic appliances. The symbols on the product, the instructions for use or the packing will inform about the methods for disposal.

ENVIRONMENTAL PROTECTION

This product is recyclable. By recycling, material recycling or other forms of re-utilization of old appliances, you are making an important contribution toward protecting our environment.

WARRANTY

This MotoMaster product carries a one (1) year warranty against defects in workmanship and materials. This product is not guaranteed against wear, breakage or misuse. Should this product become defective within the stated warranty period, return it to the store with proof of purchase, and it will be replaced or repaired free of charge.

Made in China Imported by MotoMaster Canada Toronto, Canada M4S 2B8

Motomaster 011-2064-0 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual