Motic AE2000, AE2000 TRI, AE2000 ERGO Instruction Manual

1

We are constantly endeavouring to improve our instruments and to adapt them to the requirements of
modern research techniques and testing methods. This involves modification to the mechanical
structure and optical design of our instruments.

Therefore, all descriptions and illustrations in this instruction manual, including all specifications are
subject to change without notice.

2

Content

I. Nomenclature 4

1. Application 4

2. Nomenclature 4

3. Technical data 7

II. Setting-up the Instrument 8

1. Working Environment 8

2. Input voltage and power 8

III. Assembling the Microscope Input Voltage 10

1. Installing the bulb 10

1.1 Halogen bulb 12

1.2 LED module 12

2. Filter Holder 13

3. Mounting the Condenser 13

4. Installing the Objectives 14

5. Mechanical Stage 14

6. Mounting the Eyepieces 15

IV. Microscopic Procedure 16

1. Interpupillary Distance Adjustment 16

2. Diopter Adjustment 16

3. Coarse and fine focusing 17

4. Coarse focus torque adjustment 17

5. Change the illumination between Halogen and LED 18

6. Brightfield Microscopy 19

7. Phase-Contrast Microscopy 19

8. Filter selection 21

9. Auto power off function 21

V. Photomicrographic Procedure (Model AE2000 trinocular) 23

1. Brightfield photomicrography 23

3

VI. Troubleshooting Table 24

1. Optical and Operating Problems 24

2. Electrical 25

VII. Care and Maintenance 25

1. Lenses and Filters 25

2. Cleaning of Painted or Plastic Components 25

3. When Not in Use 26

4. Warning lable 26

4

I. Nomenclature

1. Application

AE2000 incorporates the Color Corrected Infinity Optical System (CCIS) that offers superior image
quality for the transmitted and reflected illumination in the application of Living organism and tissue
observation, Petri dish observation, Live cell in culture observation.

2. Nomenclature

Model AE2000

5

Model AE2000

6

Model AE2000 TRI

Model AE2000 Ergo

7

3. Technical data

Technical data AE2000 AE2000 TRI AE2000 Ergo

Optical system Color-corrected infinity optics
Total Magnification 40X - 400X

Eyepiece tubes

360° rotatable Siedentopf with upper and lower position: upper position

offers approx. 40 mm extra viewing height

Interpupillary distance: 48 mm to 75 mm

Binocular 45° incline Trinocular 45°incline Ergo incline: 45°± 15°
Eyepiece N-WF 10X(ø20), wide field, high eye point
Nosepiece 4x, inclined backwards

Stage

Fixed, Dimensions (width x depth): 200 x 239mm

Stage height 192mm

Object guide

Verniers with numerical and alphabetic scale

X direction: numerical scale, readable from right to left

Y direction: alphabetic scale

Objectives

Plan-Achromat 4x, N.A. 0.1, W.D. 12.6mm

Plan-Achromat 10x, N.A. 0.25, W.D. 16.8mm

LWD Plan-Achromat 20x, N.A. 0.3, W.D. 4.7mm

LWD Plan-Achromat 40x, N.A. 0.5, W.D. 3mm

Plan-Achromat PH 4x Ph0, N.A. 0.1, W.D. 12.6mm

Plan-Achromat PH 10x Ph1, N.A. 0.25, W.D. 4.1mm

LWD Plan-Achromat PH 20x Ph2, N.A. 0.3, W.D. 4.7mm

LWD Plan-Achromat PH 40x Ph2, N.A. 0.5, W.D. 3mm

Condenser

N.A. 0.3, W.D. 72mm
N.A. 0.4, W.D. 53mm

N.A. 0.5, W.D. 28mm
Coarse drive 42mm/rev.
Fine drive 0.2mm/rev.
Transmitted
illumination

6V/30W Halogen

3W LED

Dimension: W x D x H 217.5 x 556 x 497mm

8

II. Setting-up the Instrument

1. Working Environment

The location should be free from dust, moisture, chemical vapours and from mechanical vibrations.
Don't locate the instrument in bright or direct ambient light, in front of a lamp, or a will-lit bright wall. Best
image will be achieved without significant ambient light.

Environmental specification:

y Indoor use
y Altitude: Max 2000m
y Ambient temperature: 15°C~ 40°C;
y Maximum relative humidity: 75% for temperature up to 31°C decreasing linearly to 50% relative

humidity at 40°C

y Supply voltage fluctuations: Not to exceed ±10% of the normal voltage
y Pollution degree: 2 ( in according with IEC60664)
y Installation/Overvoltage category: 2 (in according with IEC60664)
y Air Pressure of 75kPa to 106 kPa

2. Input voltage and power

Automatic voltage selection works with electrical outlets worldwide. It is advised to always use a power
cord that is rated for the voltage used in your area and that has been approved to meet local safety
standards. Using the wrong power cord could cause fire or equipment damage.

In order to prevent electric fluctuation to the instrument electrics, always turn the power switch on the
instrument off before connecting the power cord.

This equipment must be used with UL60950-1 Listed power supply (E246759), MFR: LI TONG
ELECTRONICS CO., LTD. Model: LTE50E.S2.3.

y Input Voltage: 12VDC
y Input Power: 48W

y Power adaptor input rating: 100-240Vac, 47-63Hz, 1A