MOST PERFECTLY ENTERPRISE 400U-G Owner's Manual

400U-G

Upright Bike

OWNER’S MANUAL

-2-

Table of Contents

Important Safety Information 3
Before You Start 4
Pre-assembly Check List 5
Assembly Instruction 6-15
Console Overview 16-22
Monitoring Your Heart Rate 23-25
Exploded View 26
Parts List 27

(2011-10 B31822TOB)

-3-

Important Safety Information

WARNING! Before using this unit or starting any exercise program, consult your physician.
This is especially important for persons over the age of 35 and/or persons with pre-existing
health problems. The manufacturer or distributor assumes no responsibility for personal injury
or property damage sustained by or through the use of this product.

SAFETY PRECAUTIONS AND TIPS

1. It is the owner's responsibility to ensure that all users of this unit have read the Owner's

Manual and are familiar with warnings and safety precautions.

2. This unit has a user maximum capacity of 250 pounds.

3. The unit should only be used on a level surface and is intended for indoor use only. The
unit should not be placed in a garage, patio, or near water and should never be used while
you are wet. We recommend a mat be placed under the unit to protect floor or carpet and for
easier cleaning.

4. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not
use the unit with bare feet, sandals, socks or stockings.

5. Always examine your unit before using to ensure all parts are in working order.

6. Allow the unit to fully stop before dismounting.

7. Pets should never be allowed near the unit.

8. Do not leave children unsupervised near or on the unit.

9. Never operate the unit where oxygen is being administered, or where aerosol products are
being used.

10. Never insert any object or body parts into any opening.

11. For safety and to prevent damage to your unit, no more than one person should use the unit
at a time.

12. Service to your unit should only be performed by an authorized service representative,
unless authorized and/or instructed by the manufacturer.

13. Failure to follow these instructions will void the unit warranty.

-4-

Before You Start

Thank you for purchasing this new Upright Bike! This quality product you have chosen was
designed to meet your needs for cardiovascular exercise. Before you start, please read the
Owner's Manual and become familiar with the operation of your new unit.

Remember to take the time to perform the stretching exercises provided to avoid injury.

If you are taking medication, consult your physician to see if the medication will affect your
exercise heart rate.
If you have heart problems, you are not active, and/or are over the age of 35 years, do not use
the pre-set programs or start an exercise program without first contacting and receiving
approval from your physician.

To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the
console. We recommend a sealed water bottle for beverages consumed while using the unit.

Please review the following drawing below to familiarize yourself with the listed parts.

-5-

Pre-assembly Check List

Parts Bag Packing List

-6-

Assembly Instruction

FIGURE 1

Attach Foot Tubes (5 & 6) to Main Frame (1) using :

Qty 4 – (47) Carriage Bolt
Qty 4 – (65) Washer
Qty 4 – (62) Nut Cap

Make sure that the Front Foot Tube (5) with Transport Wheels (36) and Rear Foot Tube (6)
with Foot Caps (37) are assembled to the Main Frame securely.

FIGURE 1

REMOVE ALL SECURITY TAPE AND WRAPPING

BEFORE BEGINNING

-7-

Assembly Instruction

FIGURE 2

Turn Locking Knob (24) counterclockwise to loosen a little , then pull it backward to hold on;
at the same time slide the Seat Post (3) into Main Frame (1) , last release Locking Knob (24) to
spring into the hole of Seat Post and secured by turning it clockwise.

* IMPORTANT

Locking Knob (24) must be locked tightly into hole in Seat Post (3) before you sit on the seat.

FIGURE 2

-8-

Assembly Instruction

FIGURE 3

Step 1:

Thread the Right Pedal (72) into the hole of Right Crank(25). Secure in place
by turning it clockwise to tighten.

Note: Right Pedal (72) is marked with an “R”.

Step 2:

Thread the Left Pedal (73) into the hole of Left Crank(26). Secure in place by
turning it counter-clockwise to tighten.

Note: Left Pedal (73) is marked with an “L”

FIGURE 3

-9-

Assembly Instruction

FIGURE 4

Step 1:

Attach Seat (71) to the Seat Post Slider (4) with 3PCS Nuts (55) and 3PCS Washers (76) which
already provided on the underside of Seat.

Step 2:

a. Turn Seat Adjustment Knob (23) counterclockwise to loosen.
b. Pull Seat Adjustment Knob (23) backward , at the same time insert Seat Post Slider (4) into

Seat Post (3) to your desired position.

c. Release the Seat Adjustment Knob (23) to spring into the hole of Seat Post Slider (4) and

turn clockwise until tight to remove any looseness.

FIGURE 4