Moser 8881-801, 8881-800 Instructions Manual

Moser Clipper Instruction Booklet

SWITCHBLADE

CLIPPER

INSTRUCTIONS

Part Numbers: 8881-801
8881-800

IMPORTANT NOTICE
Your Moser electric clipper will give years of service,
to maintain the life of your blades, we recommend
placing a few drops of clipper oil on them before,
during and after every use.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions
should always be followed, including the following:

Read all the instructions before using this appliance.

1. Do not reach for appliance that has fallen into
water, unplug it immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall
or be pulled into tub or sink. Do not place in or
drop into water or other liquid.

4. Always unplug this appliance from electrical
outlet immediately after use.

5. Unplug this appliance before cleaning.

WARNING: To reduce the risk of burns, re, electric
shock or injury to persons:

1. An appliance should never be left unattended
when plugged in.

2. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
appliance.

3. Use this appliance only for its intended use as
described in this manual. Do not use attachments other
than those recommended by manufacturer.

4. Never operate this appliance if it has a damaged cord
or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the
appliance to a service centre for examination and
repair.

5. Keep the cord away from heated surfaces.

2

3

6. Never drop or insert any object into any opening.

7. Take care when using outside, make sure appliance
remains dry at all times.

8. Do not use this appliance with a damaged or broken
comb or blade set, as this could cause an injury to the
animal.

9. Do not place or leave appliance where it may be
damaged by an animal or exposed to weather.

10. To disconnect, turn all controls to ‘off’ then remove plug
from outlet.

DIRECTIONS FOR USE:

1. Turn unit on/off
Turn variable speed switch in clockwise direction to
turn unit on or increase speed.
To turn unit off and reduce speed, turn switch anti-
clockwise until hearing a click. (g.1)

2. Remove/replace blade
The clipper should be switched off before removing
blades. Remove blade (g.2). The cutting head can
be removed by pressing the button under the blade
and pushing the blade away from the housing.

To ret the blade set, the clipper should be turned on
and running. Fit the blade into the metal guide and
press it into place. There will be a denite click when
the blade is snapped in place.

3. Remove/replace drive tip (see step 2)
Remove the drive tip by grasping with the drive tip
removal tool and pulling. (g.3a) Install by aligning the
lower end of drive nger and pushing until drive tip
snaps into position. (g.3b) (Don’t use pliers to replace
tip, as this may damage the part.)

4. Remove/replace hinge (see step 2)
Remove two screws. Lift hinge assembly from unit
(g.4)

5. Remove/replace cam follower (see step 2 and 4
Remove screw. (g.5a) Remove front cover. (g5a).
Front cover is removed by rolling the part off from the
bottom. The front cover is installed by pushing straight
onto the clipper. Remove mechanism cover by grasping
tab and pulling straight up. (g.5b) Cam follower (g.5c)
is removed by grasping tab and pulling straight up,
using needle nose pliers. (g.5d). Install by aligning as
shown in g.5d and push down to snap into location.

4

FIG.1 FIG.2 FIG.3A

FIG.3B FIG.4 FIG.5A

on

low

high

5

FIG.5B FIG.5C FIG.5D

6

BLADES AND OILING:

• Blades not only become dull cutting hair, blades are
dulled by the abrasive particles on the hair, dirt, sand
etc.

• Blades will not cut if abrasive particles are picked up
and carried by the oil lm between the blades. These
particles tend to hold the blades apart and cause
chewing and pulling instead of clean cutting.

• Oiling the blades performs two distinct functions.

1. Provides a low friction, very thin lubricant between the
cutting blades so that they can take a full cutting
stroke without becoming hot from friction.

2. Flushes abrasive particles and hair out from between
the blades.

NOTE: If you cut into dirt, immediately wash with oil to
ush out.

USE MOSER OR WAHL CLIPPER OIL ONLY

CLEANING AND GENERAL CARE

• Before cleaning/maintenance, switch the appliance off
and remove the main plug.

• Never immerse the appliance in water.

• Each time after use remove any hairs from the
cutting blade using the cleaning brush.

• Clean the body of the clipper with a soft damp cloth.
Never use solvents or scouring agents.

• The cutting head should be cleaned and oiled
frequently with Moser clipper oil in order to maintain
its good cutting performance and thus ensure a long
service life.

• The cutting head should be replaced if the cutting
performance is reduced after extended use despite
regular cleaning and lubrication.

• During use always be sure the cord is not twisted or
running over any sharp objects that might cut the cord
insulation.

7

IMPORTANT WIRING INSTRUCTIONS
WARNING: The power cord and integrated transformer
are not user serviceable parts, if either become
damaged you must contact an authorised service
agent for repair or replacement.

GUARANTEE

This product is guaranteed against defects in material and
workmanship for a period of twenty four months from the
date of the original purchase.
The guarantee will be invalidated in the case of misuse, or
repair by unauthorised persons.
Should this product become defective during the warranty
period, return it to the store of purchase together with your
proof of purchase for repair or replacement without any
charges to you.
This guarantee in no way affects your rights under
statutory law in the United Kingdom.

BLADE WEAR IS NOT COVERED UNDER THE
TERMS OF THIS WARRANTY

PRODUCT REGISTRATION

Wahl are constantly developing and launching new
products in the UK. We would like to understand your
product needs and expectations and we value any
comments you may have. As part of Wahl Customer Care,
we are offering you the chance to be kept up to date with
the latest product launches, innovations and special offers.

Please take a minute to register your product online at
www.wahl.co.uk

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
DIRECTIVE 2002/96/EC (WEEE)

At the end of this products life it should not be disposed of
with general household waste.
Care should be taken to dispose of in a suitable manner in
accordance with your Local Authority
Regulation.

WAHL (UK) LTD.
HERNE BAY TRADE PARK, SEA STREET,
HERNE BAY, KENT, CT6 8JZ
TECHNICAL SUPPORT TEL: [phone]
CUSTOMER CARE TEL: [phone]

www.wahl.co.uk

FORM No: ZA384
REV 1 - 01/10

SWITCHBLADE
CLIPPER
INSTRUCTIONS