Mosel Vitelic V62C2184096L-85BI, V62C2184096L-85T, V62C2184096L-85B, V62C2184096L-70TI, V62C2184096L-70BI Datasheet
...
MOSEL VITELIC
1
V62C2184096
512K X 8, CMOS STATIC RAM
PRELIMINARY
V62C2184096 Rev. 1.5 June 2000
Features
■
High-speed: 70, 85 ns
■
Ultra low standby current of 4 µ A (max.)
■
Fully static operation
■
All inputs and outputs directly compatible
■
Three state outputs
■
Ultra low data retention current (V
CC
= 1.2V)
■
Operating voltage: 2.3V–3.0V
■
Packages
– 32-Pin TSOP (Standard)
– 36-Ball CSP BGA (8mm x 10mm)
Description
The V62C2184096 is a very low power CMOS
static RAM organized as 524,288 words by 8 bits.
Easy memory expansion is provided by an active
LOW CE1
, and active HIGH CE2, an active LOW
OE, and three static I/O’s. This device has an
automatic power-down mode feature when
deselected.
Device Usage Chart
Operating
Temperature
Range
Package Outline Access Time (ns) Power
Temperature
MarkT B 70 85 L LL
0 °
C to 70 ° C • • • • • • Blank
–40 ° C to +85 ° C•••• • I
Functional Block Diagram
Row Decoder
Sense Amp
1024
x
4096
Column Decoder
Input Buffer
Control
Circuit
A
0
A
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
A10A11A12A13A14A15A
16
I/O1
I/O
8
OE
WE
CE1
CE2
A17A
18
2
V62C2184096 Rev. 1.5 June 2000
MOSEL VITELIC
V62C2184096
Pin Descriptions
A
0
–A
18
Address Inputs
These 19 address inputs select one of the 512K x 8
bit segments in the RAM.
CE
1
, CE
2
* Chip Enable Inputs
CE
1
is active LOW and CE
2
is active HIGH. Both
chip enables must be active to read from or write to
the device. If either chip enable is not active, the
device is deselected and is in a standby power
mode. The I/O pins will be in the high-impedance
state when deselected.
OE
Output Enable Input
The Output Enable input is active LOW. With chip
enabled, when OE is LOW and WE HIGH, data of
the selected memory location will be available on
the I/O pins. When OE is HIGH, the I/O pins will be
in the high impedance state.
WE
Write Enable Input
The write enable input is active LOW and controls
read and write operations. With the chip enabled,
when WE is HIGH and OE is LOW, output data will
be present at the I/O pins; when WE is LOW and
OE is HIGH, the data present on the I/O pins will be
written into the selected memory locations.
I/O
1
–I/O
8
Data Input and Data Output Ports
These 8 bidirectional ports are used to read data
from and write data into the RAM.
V
CC
Power Supply
GND Ground
Pin Configurations (Top View)
32-Pin TSOP (Standard)
36 BGA
A11
A9
A8
A13
WE
A18
A15
VCC
A17
A16
A14
A12
A7
A6
A5
A4
OE
A10
CE1
I/O8
I/O7
I/O6
I/O5
I/O4
GND
I/O3
I/O2
I/O1
A0
A1
A2
A3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
A
123456 1
Note: NC means no connect.
NB means no ball.
2
TOP VIEW
TOP VIEW
3456
B
C
D
E
F
G
H
A
A0
I/O5
I/O6
B
C
D
E
F
G
H
VSS
VCC
I/O7
I/O8
A9
A1
A2
NB
NB
NB
NB
OE
A10
CE2
WE
NC
NB
NB
A18
CE1
A11
A3
A4
A5
NB
NB
A17
A16
A12
A6
A7
NB
NB
NB
NB
A15
A13
A8
I/O1
I/O2
VCC
VSS
I/O3
I/O4
A14
*CE
2
is available on BGA package only.
MOSEL VITELIC
V62C2184096
3
V62C2184096 Rev. 1.5 June 2000
Part Number Information
Absolute Maximum Ratings
(1)
NOTE:
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Capacitance*
Symbol Parameter Commercial Industrial Units
V
CC
Supply Voltage -0.5 to + V
CC
+ 0.5 -0.5 to + V
CC
+ 0.5 V
V
N
Input Voltage -0.5 to + V
CC
+ 0.5 -0.5 to + V
CC
+ 0.5 V
V
DQ
Input/Output Voltage Applied V
CC
+ 0.3 V
CC
+ 0.3 V
T
BIAS
Temperature Under Bias -10 to +125 -65 to +135
°
C
T
STG
Storage Temperature -55 to +125 -65 to +150
°
C
SRAM
FAMILY
C = CMOS PROCESS
62 = STANDARD
21 = 2.3V–3.0V
OPERATING
VOLTAGE
4096K
ORGANIZATION
PKG
SPEED
62 C 821 4096 –
MOSEL-VITELIC
MANUFACTURED
V
8 = 8-bit
70 ns
85 ns
TEMP.
BLANK = 0°C to 70°C
I = -40°C to +85°C
L = LOW POWER
LL = LOW LOW POWER
T = TSOP STANDARD
B = BGA
DENSITY
PWR.
T
A
= 25 ° C, f = 1.0MHz
NOTE:
1. This parameter is guaranteed and not tested.
Truth Table
NOTE:
X = Don’t Care, L = LOW, H = HIGH
Symbol Parameter Conditions Max. Unit
C
IN
Input Capacitance V
IN
= 0V 6 pF
C
OUT
Output Capacitance V
I/O
= 0V 8 pF
Mode CE
1
CE
2
OE
WE
I/O
Operation
Standby H X X X High Z
Standby X L X X High Z
Output Disable L H H H High Z
Read LHLH D
OUT
Write L H X L D
IN
Loading...