Mosel Vitelic MSS0287 Datasheet
MOSEL VITELIC
MSS0287
VOICE ROM
Features
Single power can operate at 2.4V through 6V.
current output can drive 8 ohm speaker with a
transistor.
Total maximum duration is 2.8 seconds. Speech
+ mute is about 21.8 seconds.
Automatic power down.
Repeat function that can repeat up to 8 times.
CDS interface is provided.
It can not trigger itself by stop pulse.
Mask option for either level or edge trigger type.
Mask option for LED flasher, BUSY output or
STOP pulse output.
Mask option for either long (20ms) or short (5ms)
debounce time.
Mask option for either holdable output or not.
Mask option for either fixed (6Hz) or dynamic
type on LED flasher.
Mask option for either retrigger or not.
General Description
The MSS0287 is a single-chip CMOS LSI that memorizes voice up to 2.8 seconds using the MOSEL
qualified coding method (MPCM). The chip contains most of the necessary circuit like oscillator, PLA, D/A
converter, buzzer buffer, control and timing logic . Therefore, it can apply to various voice systems with
minimum external parts. Several device can be combined to reach longer voice duration (longer than
2.8 seconds). Customer speech data will be edited and programmed into PLA by changing one mask
during the device fabrication.
Block Diagram
V
DD
OSC
OSCILLATOR
ADDRESS
GENERATOR
CONTROL LOGIC
LED/BUSY/STOP
V
SS
PLA
TG
1
D/A
COUT
PID223B 02/95
MOSEL VITELIC
Absolute Maximum Rating
Symbol
V ~ V
DD SS
V (TG)
IN
V (STOP)
OUT
T (Operating)
T (Storage)
Pad Description
Rating
-0.5 ~ +7.0
V -0.3 < V < V +0.3
SS IN DD
V <V < V
OUTSS DD
-10 ~ +60
-55 ~ +125
MSS0287
VOICE ROM
Unit
V
V
V
C
C
Pad No. Signal Name Function
1
2
3
4
5
6
7
V
DD
OSC
Reserved
LED/BUSY/STOP
TG
C
OUT
V
SS
I/O
Power
I
NC
O
I
O
Power
Positive power supply
Oscillator resistor input
Reserved no Connection
LED flasher output/BUSY signal output/One shot stop signal output.
Trigger input, active high
Current output for driving speaker
Negative power supply
DC Characteristics
Symbol
I
SB
I
OP
I
IH
I
IL
I
OC
I
BZ
I
STOP
I
OH
I
OL
∆F/F
Parameter Min. Max.Typ. Unit
Supply
Current
Stand by
Operating
Input Current (TG)
0
Output Current (C )
Output Current (
Output Current (
OUT
BUSY
STOP
Output Current
(LED)
)
)
5
-9
-9
-8
+8
Frequency Stability
1
200
+15
+5
µA
µA
mA
mA
mA
mA
Condition
V = 4.5V, I/O Open
DD
V = 4.5V
DD
V = 3V,
DD
V = 4.5V,
DD
V = 4.5V,
DD
V = 4.5V,
DD
V = 4.5V,
DD
F
%
OSC
full scale.
V = V
V
(4.5V) - F
F
OSC
(4.5V)
O/P
O/P
OSC
=V
OH
OL
(4V)
∆F/F
Frequency Variation
AC Characteristics
Symbol
STOP
T
T
Parameter Min. Max.
Pulse Width (STOP)
Minimal trigger
pulse width
Typ.
40
20
5
+10
2
%
Unit
msT
ms
V = 4.5V, R
DD
Condition
VDD=4.5V
Mask = long
Mask = short
OSC
= 1.2MΩ
PID223B 02/95
Loading...