Page 1
www.morrisonoutdoor.com
Petrol Blower
BL260E S2
Including Engines 1E34FB & 1E34F-2E
Owner’s Manual
Part No: 548313.B.0
Revised May 2018
Important
Please read this Owner’s Manual and the Express Warranty before using this product. The Warranty does not cover
damage due to misuse or failure to follow the operating and assembly instructions.
Keep these instructions in a safe place for future use.
Page 2
2
Do not operate this machine before it has been
assembled correctly and you have read and
understood these instructions.
These instructions are intended as a general
guide and do not supersede national or local
codes in any way. Contact local Authorities for
clarity of laws relating to operation of this
appliance.
Keep the instructions in a safe place for future use.
Contents
Warning Symbols on the Machine 2
Symbols in this Owner’s Manual 2
Proper Use 2
Safety Instructions 2
Important Information! 3
Operation Warning! 3
List of Parts 3
Assembling the Blower 3
Mixing Fuel 4
Filling the Fuel Tank 4
Starting the Machine 4
Adjusting Engine Idle Speed 5
Stopping the Engine 5
Using the machine 5
Routine Maintenance 6
Spark Arrestor Maintenance 6
Storage for over 30 days 7
Warning Symbols on the Machine
Caution! Read the operating instructions
and follow the warnings and safety
instructions.
This product is for outdoor use only and to
be used in a well ventilated area.
Wear protective eye wear and ear muffs.
1. AVOID DANGEROUS WORK ENVIROMENTS. Do not use
power tool in damp or wet locations or expose power tools
to rain. Do not use power tools in the presence of flammable
liquids or gases as normal sparking of the motor could ignite
fumes. Keep work areas well lit.
2. KEEP CHILDREN AND VISITORS AWAY. Visitors and
children should wear safety glasses and be kept a safe
distance from the work area. Do not let others make contact
with the tool or extension cord.
3. AVOID UNINTENTIONAL STARTING. Always check that the
switch is in the OFF position before plugging in the tool to the
power supply. Do not carry a plugged in tool with your finger on
the switch.
4. STORE TOOLS SAFELY. When not in use, tools should be
stored in a dry place, high and locked-up place, out of reach of
children.
5. DISCONNECT IDLE TOOLS. Switch off the power and
disconnect the plug from the power supply before servicing,
when changing accessories and when the tool is not in use.
6. DO NOT FORCE THE TOOL. The tool willl do the job better
and safer working at the rate for which it was designed.
7. USE THE CORRECT TOOL FOR THE JOB. Do not force
small tools or attachments to do the job of a heavier duty tool.
Never use a tool for a purpose for which it was not intended.
8. DRESS CORRECTLY. Do not wear loose clothing or jewellery,
they can be caught in moving parts. Rubber gloves and nonslip footwear and recommended when working outdoors. If you
have long hair, wear a protective h air covering.
9. ALWAYS USE SAFETY ACCESSORIES. Safety glasses and
earmuffs should always be worn. Everyday eyeglasses have
impact resistant lenses only, they are not safety glasses. A face
or dusk mask is also required if dust is going to be created.
10. DON’T OVERREACH. Keep proper footing and balance at all
times. Do not use tool on a ladder or unstable support. Secure
tools when working at elevated levels.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions
for lubricating and changing accessories. Inspect tool cords
periodically and, if damaged have them repaired by an
authorised service facility. Inspect extension cords periodically
and replace them if damaged. Keep tool handles dry, clean
and free from oil and grease. Never use brake fluids, gasoline,
petroleum based products, or any strong solvents to clean your
tools.
12. REMOVE ADJUSTING KEYS AND WRENCHES. Check to
see that keys and adjusting wrenches are removed from the
tool before switching it on.
13. STAY ALERT AND EXERCISE CONTROL. What was you are
doing and use.
80˚C+
Warning! When in use, and in the cool down
period after use this surface is very hot. Do
not touch as doing so can result in serious
burns.
KEEP HANDS
AND FEET
CLEAR
Warning! Keep hands and feet clear when
machine is operating as rotating parts can
cause serious injury.
FLAMMABL E
FUEL
Warning! Flammable fuel keep away from
naked flames and cigarettes.
Page 3
3
Symbols in this Owner’s Manual
Threatened hazard or hazardous situation.
Not observing this instruction can lead to injuries or
cause damage to property.
Important information on proper handling.
Not observing this instruction can lead to faults in the
machine.
User information. This information helps you to use
all the functions correctly.
Keep this owners manual for future reference and for
others who may want to use this tool.
Proper Use
For safety reasons, the BL260 S2 are not to be used by children,
young people under 16 years of age, or any other persons who are
not acquainted with these directions for use.
Specific safety information Please read this safety
information and the directions for use carefully and be
sure to follow the instructions to the letter.
Failure to follow safety instructions can result in
serious injury to yourself and others.
Safety Instructions
Use the machine only as described in this manual. Any other types
of use are at your own risk and could well be dangerous. The
manufacturer cannot be held liable for damage caused by improper
or incorrect usage.
Warning!
Read the operating instructions in their entirety
before using the machine for the first time. All the
information on the handling of the machine is relevant
to your personal safety. Ask a professional to show
you to use the machine!
Do not operate this machine if you are tired, ill
or are under the influence of alcohol, drugs or
medicine.
This Owner’s Manual covers two engine options for the BC260
Blower.
Before starting, check the machine is in good working order. If
damage is discovered, have it repaired by a specialist immediately.
Always wear goggles and protective ear muffs when working with
the machine.
Always switch off the machine before pulling it down.
Always stop the engine before doing any work on the machine.
Only one person must use the machine at a time. All other persons
must stay clear of the Blower. Children and pets in particular must
be kept well away at all times.
Important Information!
The information contained in this manual describes machines
available at the time of production. While every attempt has been
made to give you the very latest information about your Petrol
Blower, there may be some differences between your machine and
what is described here. We reserve the right to make changes in
production without prior notice, and without obligation to make
alterations to machines previously manufactured.
Before using this product, consult local regulations concerning
noise restrictions and hours of operation
Caution!
This petrol engine blower is equipped with a spark
arresting muffler. Never operate this machine without
both the muffler and spark arrestor installed and
properly functioning!
Operation Warning!
Important!
The operational procedures described in this manual
are intended to help you get the most from your
machine and also to protect you and others from
harm. These procedures are general guidelines only,
and are not intended to replace any safety rules/laws
that may be in force in your area.
If you have any questions regarding your petrol
engine blower, or if you do not understand something
in this manual, your dealer will be glad to assist you.
.
Warning!
Do not make unauthorised modifications to this
machine!
List of Parts
Choke
Recoil/Start
er Handle
Air Cleaner
Fuel filler cap
Fuel primer
bulb
Exhaust
outlet
Throttle lever
Spark plug
Page 4
4
Assembling the Blower
Place the blower upright on the ground or on a sturdy work surface.
Grasp the straight tube as shown, and push the tube over the
blower discharge port and locking pins.
Lock the straight tube to the blower discharge port by rotating the
tube as shown.
Grasp the nozzle tube with the label “TOP” positioned as shown,
and then push the nozzle over the straight tube and locking pins.
Lock the nozzle tube to the straight tube by rotating the nozzle tube
as shown.
5.Secure the top straight connecting tube to the outlet
port with the supplied screw.
1
3
4
2
Locking pin
Straight tube
Straight tube
Rotate clockwise
to lock
Rotate clockwise
to lock
Label ‘Top’
must face
up
Push the straight
tube over the discharge port and locking pin.
Push the nozzle tube over
the straight
tube and locking pin.
5
Screw M5 x 10
Important!
Blower tube installation affects both blower balance
and performance!
The tube and nozzle are correctly installed when the
label “TOP” is visible to the operator during normal
operation.
Warning!
Danger from rotating impeller! Stop the engine before
installing or removing the blower tubes!
Never perform any maintenance or assembly
procedures on this machine while the engine is
running!
Mixing Fuel
Fuel Requirements
Use only fresh, clean fuel
Use only fuel with an octane rating of 90 or higher
2 Stroke Oil / Fuel Mixing Ratios and Volumes
It is recommended to always use Masport oils as these are
formulated for best results. If Masport oil is not available, check with
a Service Dealer for a suitable alternative.
Important!
Check type of oil, ‘Mineral Oil’ or ‘Semi Synthetic Oil’
First 20 Hours of Use
Use mixture of 25:1 = 40ml of oil for each one (1) litre of Petrol.
After First 20 Hours of Use
If Using Mineral Oil, it is recommend using a mixing Ratio of 25:1
Note - 25:1 = 40ml of oil for each one litre (1) of Fuel
if using Semi Synthetic Oil, it is recommended using a mixing Ratio
of 40:1
Note - 40:1 = 25ml of oil for each one litre (1) of Fuel
Warning!
Incorrect amount of oil will cause failure of the motor,
plus void any warranty claim. Incorrect oil or poor fuel
can cause failure of the motor, plus void any warranty
claim. Do not store fuel for longer then 3 months;
as stale petrol can cause motor issues. Mix only the
required amount of fuel for the task; ensure petrol is
fresh.
Warning!
Danger of fire! Never transfer or store fuels in the
presence of combustible materials! Before starting
the engine, always move the blower to a clear area
at least 10 feet (3 metres) away from fuels and other
combustible materials!
Warning!
Never attempt to mix fuel in the blower fuel
tank!Always mix all fuels in a clean, container!
Use 2-stroke engine oil or equivalent oil mixed at the
recommended ratio for your model. Be aware that
generic oils and some outboard mixing oils may not
be intended for use in high performance air cooled
2-cycle engines, and should never be used in your
engine blower. If unsure seek advice from your
garden product specialist. Add fuel in a well ventilated
area. Wipe away an spilt fuel before starting the
engine.
Important!
Mix only enough fuel for your immediate needs! If fuel
must be stored longer than 30 days, it should first be
treated with a stabiliser or equivalent product!
Filling the Fuel Tank
Warning!
Danger of fire and burn injury!
Page 5
5
Filler
cap
Place the blower upright on the ground
or on a sturdy work surface, and wipe
any debris from around the fuel cap.
Remove the fuel cap.
Fill the tank with clean, fresh fuel.
Replace the cap, and wipe away any
spilled fuel before starting the blower.
Always use extreme care when handling fuel! Fuel is highly
flammable!
Never operate this blower if fuel system components are damaged
or are leaking!
Never attempt to refuel the engine while it is running!
Never attempt to refuel a hot engine! Always allow the blower
engine to cool before fuelling!
Never smoke or light any fires near the blower or fuels!
Always transport and store fuels in an safe container!
Never place flammable material close to the engine muffler!
Never operate the blower without a properly functioning muffler and
spark arrestor installed!
Never operate the blower unless it is properly assembled and in
good working condition!
Starting the Machine
Warning!
Danger from rotating impeller! The impeller will rotate
whenever the blower is operated! Never operate this
blower unless the intake cover and blower tubes
are properly installed and in good working order.
Danger from thrown dust or debris! Always wear eye
protection when operating this machine! Never direct
the blower stream toward people or animals!
Never operate this blower unless all controls are
properly installed and in good working order.
Warning!
The recoil starter can be damaged by abuse!
• Never pull the starter cord to its full length.
• Always engage the starter before cranking the
engine!
• Always rewind the starter cord slowly!
• Never operate the blower if blower tubes are
missing or damaged!
Important!
A two-position “ON-OFF” switch located on the left of
the blower handle grip controls the engine ignition
Fuel filler
line
Fuel
primer
bulb
Starting Procedure:
Prime the fuel system by repeatedly
depressing the fuel primer bulb until
no air bubbles are visible in the fuel
discharge line.
Cold Engine Only. Choke the engine
by pulling the choke control to the
fully extended position (choke is
closed).
Place the blower on the ground, and hold the blower handle firmly
with your right hand.
Pull the starter cord slowly until you feel the starter engage, then…
... Start the blower by pulling the starter cord upward rapidly. If
necessary, repeat two or three times until the engine starts.
Important!
When the engine starts:
For maximum performance and operating life, allow the engine to
warm before use.
Run the engine at idle speed until operating temperature is reached
(2-3 minutes).
As the engine warms open the choke gradually by slowly pushing
the choke control in to the fully retracted position.
The machine should now be ready for use.
If the engine does not start:
Repeat the appropriate starting procedure for “hot” or “cold”
engine. If the engine still will not start, follow the “Starting a Flooded
Engine” procedure (below).
Starting a flooded engine:
Disconnect the spark plug lead, and use the spark plug wrench to
remove the plug in a counterclockwise direction.
If the spark plug is fouled or is soaked with fuel, clean or replace the
Choke control.
Pull to close
plug as required.
Clear excess fuel from the
combustion chamber by cranking
the engine several times while the
spark plug is removed.
Install the spark plug and firmly
tighten it with the spark wrench.
If a torque wrench is available,
torque the spark plug to 148-165
inch-pounds. Reconnect the spark
plug lead.
Ensure the choke control
lever is in the appropriate position for the temperature of the engine.
Repeat the starting procedures for “warm engine”.
If the engine still fails to fire or start, refer to the troubleshooting
flowchart at the end of this manual.
Adjusting Engine Idle Speed
Idle speed
adjustment
screw.
Accessible
through cowl
louver.
Start the engine by following the procedures described on the
preceding pages.
Run the engine at idle speed until operating temperature is reached
(2-3 minutes).
Use a screwdriver to adjust the engine idle speed to 2800-3000
rpm.
Turn the idle screw clockwise to increase engine idle speed.
Turn idle screw counterclockwise to decrease engine idle speed.
Page 6
6
Important!
Blower tubes and the intake cover must be installed
while adjusting engine idle! Engine idle speed will also
be affected if either the intake cover or blower tubes
are blocked, damaged or incorrectly installed!
Stopping the Engine
Cool the engine by allowing it to run at idle for 2 to 3 minutes.
Stop the engine by pulling the ignition switch.
Important!
If the engine continues to run while pulling the
ignition switch, stop the engine by pulling the choke
control out to the fully closed position. A clean and
unrestricted airflow is essential to your blower’s
engine performance and durability!
Before attempting any carburettor adjustments, inspect and clean
the engine air cleaner as described under the heading ‘Every 10
Hours’, on Page 6 of this manual.
Using the machine
Think Safety!
In the hands of an experienced operator, the machine can efficiently
move a wide variety of debris ranging from grass clippings to gravel.
As a general rule, try to operate your engine at the lowest throttle
setting necessary to get the job done:
Use low throttle settings when clearing lightweight materials from
around lawns or shrubbery.
Use medium to higher throttle settings to move lightweight grass or
leaves from parking lots or walkways.
Use full throttle when moving heavy loads such as dirt or snow.
User Information!
Noise increases at higher throttle settings! Always use the lowest
throttle setting required to get the job done!
Safe operation
Machine noise increases at higher throttle settings! Always use the
lowest throttle setting required to get the job done!
Never operate the blower when visibility is poor.
Always wear eye protection such as face shield or goggles while
operating this machine.
Wear a dust mask to reduce the risk of inhalation injuries.
Wear close fitting clothing to protect your legs and arms.
Wear hearing protection when operating this machine.
Never operate the blower if any component parts are damaged,
loose, or missing.
1. Using the blower
Always be aware of the strength and
direction of stream. Never direct the
blower discharge stream toward
people or animals.
Routine Maintenance
Warning!
Before performing any maintenance on this blower,
stop the engine and disconnect the spark plug wire!
Daily Maintenance
Remove dirt and debris from the blower exterior.
Inspect the engine, tank, and hoses for possible fuel leaks, and
repair as necessary.
Inspect the engine cooling fins for accumulations of dirt or debris,
and clean as necessary.
Important!
Dirty or damaged cooling system components
may allow the engine to overheat, possibly causing
serious engine damage!
Important!
Operating the blower with loose, missing, or
damaged components could allow the engine to over
speed, possibly causing serious engine damage!
Inspect the entire blower for damage, loose or missing components
or fastenings, and repair as necessary.
EVERY 10 HOURS
More frequently in dusty conditions.
Air
cleaner
cover
Cover
retaining
screw
Air
cleaner
element
Loosen the air cleaner cover retaining
screw, and remove the cover and filter
element.
Inspect the element. If the element is
distorted or damaged, replace it with
a new one.
Wash the element in clean fuel, and
squeeze or blow dry. Wash the air
cleaner cover in clean fuel, and wipe
air blow dry.
Install the element and cover and then
tighten the cover retaining screw.
Remove sparkplug
by turning anticlockwise.
EVERY 10/15 HOURS
Use the spark plug wrench to remove
the spark plug (turn counter-clockwise to
remove).
Clean and adjust the spark plug gap to
0.6-0.7mm. Replace any damaged or
visi-bly worn plug with the correct plug or
it’s equivalent
Install the spark plug finger tight in the
cylinder head, then tighten it firmly with
the spark plug wrench. If a torque wrench
is available, torque the spark plug to 148165 inch pounds.
Important!
Never allow dirt or debris to enter the cylinder
bore!Before removing the spark plug, thoroughly
clean the spark plug and cylinder head area!Allow
the engine to cool before servicing the spark plug!
Cylinder tightening or loosening the spark plug
while the engine is hot can result in serious engine
damage! Incorrect spark plug installation can result in
serious engine damage!
Page 7
7
EVERY 50 HOURS
More frequently if you notice reduced performance.
INSPECTION
Inspect the entire blower and tubes for damage, including loose or
missing components, and repair as necessary.
SPARK PLUG
Replace the spark plug with a Champion RCJ6Y, gapped to (0.6-
0.7)mm.
FUEL FILTER
Fuel filter
Use a wire hook to extract the
fuel filter from inside the fuel
tank, and then remove and
wash the filter element in clean
fuel. Before reinstalling the filter,
inspect the condition of the fuel
line. If damage or deterioration is
noted, the blower should not be
used until it can be inspected by
a trained service technician.
COOLING SYSTEM
Remove the engine cover (as
described under ‘Spark Arrestor Maintenance), and use a wood or
plastic scraper and a soft brush to remove dirt and debris from the
cylinder fins and crankcase.
Spark Arrestor Maintenance
Hard starting or gradual loss of performance can be caused by
carbon deposits lodged in the spark arrestor screen. For maximum
performance, the spark arrestor screen should be periodically
cleaned as follows:
Remove the
engine cover
Self tapping
screw
Self tapping
screw
Self tapping
screw
Machine
screws
Remove the
engine cover
Self tapping
screw
Spark
arrestor
screen
Spark
arrestor
chamber
Spark
arrestor
cover
Retaining
screw
Gasket
Self tapping
screw
Self tapping
screw
Machine
screws
Remove the spark plug.
Remove three self tapping screws and two machine screws from
the engine cover, and then gently move the engine cover aside.
Remove the three spark arrestor retaining screws, and then remove
the spark arrestor cover, screen, gasket, and chamber
Use a plastic scraper or wire brush to remove carbon deposits from
the arrestor screen, chamber, and cover.
Inspect the screen carefully, and replace any screen that has been
perforated, distorted, or is otherwise unserviceable.
Install the chamber, screen, gasket and cover in the reverse order
of disassembly, and then install and securely tighten the three cover
retaining screws.
Install the engine cover, and verify that the fuel line connections are
still tightly in place.
Install the engine cover retaining screws in the reverse order of
removal, and tighten securely.
Install and tighten the spark plug, and reconnect the spark plug
wire.
Drain the fuel if it is to be stored for an extended time.
Important!
Always replace cover screws in the same holes
from which they were removed. Substitution or
incorrect assembly of the engine cover screws can
permanently damage aluminium castings and plastic
components!
Storage for over 30 days
CLEANING Thoroughly clean the machine exterior.
INSPECTION Inspect the entire machine and tubes for damage,
including loose or missing components, and repair as necessary.
FUEL Drain the fuel tank, and then clear the carburettor and lines
by running the machine until it stops from lack of fuel.
LUBRICATION Remove the spark plug, and then pour
approximately 1/4-oz of oil into the cylinder through the spark plug
hole. Before reinstalling the spark plug, pull the recoil starter 2 or 3
times to distribute the oil over the cylinder walls.
AIR CLEANER Remove, clean, and reinstall the filter element as
described under “daily maintenance.”
STORAGE Store the machine in a clean, dry, dust free environment.
Warning!
Never store the machine with any fuel remaining in
the tank, fuel lines, or carburettor! Your warranty does
not include coverage for damage caused by ‘stale’ or
contaminated fuels!
Page 8
8
What to Check Possible Cause Remedy
Does the engine crank? NO Faulty recoil starter.
YES Fluid in the crankcase. Return blower to dealer
Internal damage.
Good compression? NO Loose spark plug. Excess wear Tighten and re-test. Return blower to
YES on cylinder, piston, rings. dealer.
Does the tank contain fresh NO Fuel/mixture incorrect, stale, contaminated.
fuel of the proper grade?
Re-fill with fresh fuel (2-cycle engine
oil and gasoline)
YES
Is fuel visible and moving in NO Check for clogged fuel filter and/or vent. Clear as required. Re-start.
the return line when priming?
YES
Check the spark plug If the plug is wet, excess fuel may be Crank the engine with plug removed,
in the cylinder. replace the plug and restart.
The plug may be fouled or Clean and regap the plug to
improperly gapped. 0.6-0.7mm. Restart.
The plug may be damaged internally Replace the plug with a
or of the wrong size. Champion RCJ6Y. Restart
Engine does not start
Page 9
9
What to Check Possible Cause Remedy
Is the engine overheating? Operator is overworking the machine. Use lower throttle setting.
Carburettor mixture is too lean. Return blower to dealer.
Improper fuel ratio.
Re-fill with fresh fuel of the correct
mixture (2-cycle engine oil and
gasoline)
Fan cover, cylinder fins dirty or damaged. Clean, repair or replace as necessary.
Carbon deposits on piston or in the muffler. Decarbonize.
Engine is rough at all speeds. Clogged air cleaner element. Service the air cleaner.
May also have black smoke and/or Loose or damaged spark plug. Tighten or replace.
unburned fuel at the exhaust. Air leakage or clogged fuel line. Repair or replace filter and/or fuel line.
Water in the fuel. Drain the fuel dealer replace the fuel.
Piston seizure. Return blower to dealer.
Faulty carburettor and/or diaphragm. Return blower to dealer.
Engine is knocking. Overheating condition. Idle engine until cool; find reason for
overheat.
Improper fuel. Check fuel octane rating; check for
presence of alcohol in the fuel. Refuel
as necessary.
Carbon deposits in the combustion
chamber. Decarbonize.
What to Check Possible Cause Remedy
Does the engine crank? NO Faulty recoil starter.
YES Fluid in the crankcase. Return blower to dealer
Internal damage.
Good compression? NO Loose spark plug. Excess wear Tighten and re-test. Return blower to
YES on cylinder, piston, rings. dealer.
Does the tank contain fresh NO Fuel/mixture incorrect, stale, contaminated.
fuel of the proper grade?
Re-fill with fresh fuel (2-cycle engine
oil and gasoline)
YES
Is fuel visible and moving in NO Check for clogged fuel filter and/or vent. Clear as required. Re-start.
the return line when priming?
YES
Check the spark plug If the plug is wet, excess fuel may be Crank the engine with plug removed,
in the cylinder. replace the plug and restart.
The plug may be fouled or Clean and regap the plug to
improperly gapped. 0.6-0.7mm. Restart.
The plug may be damaged internally Replace the plug with a
or of the wrong size. Champion RCJ6Y. Restart
Engine does not start
Low Power Output
Page 10
10
Additional Problems
Symptom Possible Cause Remedy
Poor acceleration. Clogged air cleaner element. Clean the element.
Clogged fuel filter. Replace the fuel filter as required.
Carburettor mixture too lean. Return blower to the dealer.
Idle speed set too low. Adjust: 2800-3000 rpm.
Engine stops abruptly. Fuel tank empty. Refuel.
Clogged fuel filter. Clean or replace the fuel filter as
required.
Water in the fuel. Drain; replace with clean fuel.
Shorted spark plug or loose terminal. Clean and replace spark tighten the
terminal.
Ignition failure. Return blower to the dealer.
Piston seizure. Return blower to the dealer.
Engine difficult to shut off. Ground (stop) wire is disconnected, Test and replace as required.
or switch is defective.
Overheating due to incorrect spark plug. Correct plug: Champion RCJ6Y
Overheated engine. Idle engine until cool.
Excessive vibration. Warped or damaged blower fan. Inspect and replace fan as required.
Loose bolt or fastener. Tighten as required.
Internal engine damage. Return blower to dealer.
Specifications
Model BL-260 S2 BL-260E S2
Dimensions 325l x 230h x 330w 325l x 230h x 330w
Engine Two stroke air cooled petrol/oil engine,
vertical cylinder
Two stroke air cooled petrol/oil engine,
vertical cylinder
Engine Model 1E34FB 1E34F-2E
Bore & Stroke 34 x 28 34 x 28
Displacement 25.4cc 25.4cc
Fuel Gasoline/oil mixture Gasoline/oil mixture
Carburettor Diaphragm-type with primer pump Diaphragm-type with primer pump
Ignition All transistor electronic ignition system All transistor electronic ignition system
Spark plug Champion RCJ6Y Champion RCJ6Y
Starting Recoil starter Recoil starter
Stopping Grounding (toggle switch) Grounding (toggle switch)
Fuel Tank Capacity 0.5 Litre 0.5 Litre
Exhaust system Low dB; spark-arrestor muffler Low dB; spark-arrestor muffler
Air Cleaner Type Semi-wet Semi-wet
Weight; dry, fully assembled 4.2kg 4.6kg
Performance 0.75kw 0.70kw
Engine Idle Speed 2800 +/- 150 rpm 2800 +/- 150 rpm
Sound 112dB(A) 109dB(A)
Page 11
11
Page 12
Head Office - New Zealand
1-37 Mt Wellington Highway, Panmure, Auckland 1060
P.O. Box 14 349, Panmure, Auckland 1741
Loading...