Page 1
Page 1 of 6
52’’ CEILING FAN WITH LED LIGHT
INSTRUCTIONS MANUAL
MODELS: MCF-16233 / MCF-16234
Read these instructions carefully and keep them for future reference
Page 2
Page 2 of 6
SAFETY INSTRUCTIONS
Warning: To reduce the risk of fire, electric shock, or personal injury, read the following
instructions very carefully:
READ THESE INSTRUCTIONS
1. The fan should not be connected to any power point. Install the fan on the ceiling.
2. The minimum distance between the blades and the floor must be 2.3m. If you use
a hook to hang the fan, the maximum weight capacity is 100kg.
3. Make sure that you cap with wire connectors. Make sure to cap the wires you will
not use with a wire connector.
4. Disconnect the fan from the mains power before mounting or repair.
5. The cable must be properly earthed in order to avoid any risk of electrocution.
6. All electrical connections must be in accordance with local and national Electrical
codes
7. Installation by a qualified electritian is highly recmmended.
8. Never install the fan in a room with a high degree of humidity.
9. Be careful when you are close to the fan blades.
10. If the supply cord is damaged it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
11. This appliance is designed for dry places (Don’t use in wet places).
12. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the appliance.
14. WARNING: In order to ensure children’s safety, please keep the contents of the
package out of their reach (plastic bags, polystyrene, boxes etc.).
15. Important: always turn off the electricity supply to the ceiling fan during installation
or maintenance. It is recommended to remove the fuse or turn off the circuit –
breaker connector when handling (switching it off is not enough).
16. Before operation make sure that all connections are secured, to prevent the fan
from falling.
Page 3
Page 3 of 6
FAN INSTALLATION ILLUSTRATION
1. Secure the mounting plate to a
ceiling joist with the two screws,
spring washers and the flat
washers provided. Ensure that
the support for the mounting plate
is capable of safely and securely
hold the moving weight of the fan.
2. Fasten the blades to the motor with
the screws and spring washers that
are already attached to the motor.
3. Connect the light kit by
clipping together the two plastic
male/female connectors.
4. Fit the LED lamp panel to the
lamp panel mounting bracket by
using the three light kit-fixing
screws and star washers. Ensure
that wires are not trapped.
5. Hang the fan assembly onto the
mounting plate. The lug of the
mounting plate should be lined up
with the corresponding groove on the
ball joint of the fan assembly.
6. Insert the remote control
receiver between the bracket and
the ball joint, and the sensor as
shown.
7. Insert all the male connector
into the female connector (from
the remote control receiver to the
fan, and from the remote control
receiver to the terminal block.
8. Connect the wires from the earthed
mains supply to the terminal block.
9． Lift the fan until the screws
reach the bottom of the slots and
then rotate the canopy
counterclockwise until the screws
drop into the slot recesses.
10. Insert the two sets of screws
and washers. Tighten all the
screws, making sure that the
canopy is secure and that wires
are not trapped. Ensure that the
slot of the nylon ball hanger fits
into the guide pin of the upper
canopy.
11. Install the lampshade onto the
shade gallery by rotating the
lampshade clockwise.
Page 4
Page 4 of 6
REMOTE CONTROL
Use the remote control transmitter to set the speed of the fan,
to set the dimmer and to switch the light and fan on or off.
Battery replacement: Open the battery compartment cover on
the remote control transmitter in the direction of the arrow, fit 2
x “AAA” batteries, making sure that the polarity of the batteries
match with the figures shown in the battery compartment.
(Note: Batteries NOT included). Re-assemble the battery
compartment cover.
ALWAYS ensure that the battery compartment cover is
properly closed.
DON”T expose the remote control to direct sunlight.
DON”T attempt to recharge expired batteries, there are special
rechargeable batteries.
DON”T dispose of batteries in fire, to avoid explosion.
OPERATING YOUR FAN
There is a switch on the motor housing to set the rotation of the blades.
Note: Make sure that the fan stops operating before using the Direction Switch.
In order to prevent any damage to the motor or injury to you, the switch should
stay at the RIGHT or LEFT position when the fan is working.
Cold weather: Push switch to the “RIGHT” so that the
blades move downwards the warm air trapped near
the ceiling fan.
Hot weather: Push switch to the “LEFT” so that the
blades create a breeze and circulate the air inside the
room.
You can also change the rotation of the blades from
the remote control.
Page 5
Page 5 of 6
For the first use, the fan and the remote control are already paired. Pair setting
maybe needed in following situations:
1. You would like to use one remote control to control more than one fan.
2. You get a new wireless remote control spare part
Page 6
Page 6 of 6
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life,
should be disposed of separately from your household waste. Please
dispose of this equipment at your local community waste collection/
recycling centre.
In the European Union there are separate collection systems for used electrical and
electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the requirements of
below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
ErP Directive 09 / 125 / EC
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at www.morris.gr
Exclusive importer in Greece:
Amiridis – Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki – Greece
T: +302310944944 | F: +302310944940
www.amiridis-savvidis.gr
Loading...