Morris A1608EM Instruction Manual

19 Bar 3 in 1 Coffee Machine

Model: A1608EM

Rating: 220-240V~ 50/60Hz - 1550W

Instruction Book

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:

- Read all instructions and information in this instruction book and any
other literature included in this carton referring to this product before
operating or using this appliance.

- Do not touch hot surfaces. Use handles or knobs.

- Children should be supervised to ensure that they do not play with the
appliance

- To protect against fire, electric shock and personal injury do not
immerse cord, plugs, or appliance in water or other liquid.

- Close supervision is necessary when any appliance is used by or near
children.

- Switch off and unplug this appliance when not in use and before
cleaning. Allow the appliance to cool down before putting on or taking
off parts, and before cleaning the appliance.

- Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to authorized service centre for examination, repair or
adjustment.

- If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.

-The use of an accessory attachments not recommended by the
appliance manufacturer may result in fire, electric shock or injury to
person.

- Do not use this appliance outdoors.

- Do not let cord hang over edge of table or counter, or touch hot
surfaces.

- Do not place on or near a hot gas or electric burner, or in a heated
oven.

- Always attach plug to appl iance first, then plug c ord into the w all outlet,
to disconnect, switch off any control, then remove plug from wall
outlet.

- Do not use appliance for other than intended use.

- Do not open top lid and turn off filter holder while the machine is in
operation. Wait until brewing cycle is completed and all water and
steam has been used out.

- This appliance is not intended for use by person (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.

- This appliance is intended to be used in household and similar
applications such as staff kitchen areas in shops, offices and other
working environments; farm houses; by clients in hotels, motels and
other residential type environments; bed and breakfast type
environments

- Appliances with Glass Carafes.

A. The carafe is designed for use with this appliance only. It must
never be used on a range top.

B. Do not put a hot carafe on a wet or cold surface.
C. Do not use a cracked carafe or a carafe having a loose or

weakened handle.

D. Do not clean carafe with cleansers, steel wool pads, or other

abrasive material.

Special Cord Set Instruction:
Regarding your Cord Set:

A. A short power-supply cord is to be provided to reduce risks resulting

from becoming entangled in or tripping over a longer cord.

B. Longer extension cords are available and may be used if care is

exercised in their use.

C. If a long extension cords is used,

1) The marked electrical rating of the extension cord should be at
lest as great as the electrical rating of the appliances,

2) If the appliance is of the grounded type, the extension cord
should be a grounding-type 3-wire cord,

3) The longer cord should be arranged so that it will not drape
over the counter top or table top where can be pulled on by
children or tripped over.

CAUTION

This appliance is for household use. Any servicing other than cleaning
and user maintenance should be performed by an authorized service
representative.

- Do not immerse this coffee machine in water or any other liquid.

- To reduce the risk of fire or electric shock, do not remove the base. No
user serviceable parts inside. Repair should be done by authorized
service personnel only.

- Check voltage to be sure that the voltage indicated on the bottom
agrees with your voltage.

- Never use warm or hot water to fill the water container, use cold water
only.

- Never refill the water chamber while this coffee machine is in the "on"
position. Turn the coffee machine off before refilling with water.

- Do not place carafe on a hot surface or in a heated oven.

- Before t urning on this coffee machine, please make sure that carafe

sits flat on inside circle of heating plate.

- Never remove carafe before brewing is completely finished, i.e.
dripping from the filter holder into the carafe has stopped completely.

- Keep your hands and the cord away from hot parts of the machine
during operation.

Exposed Diagram and main parts list

Push button diagram

Before First Use

Before using the appliance for the first time and also after a long period
of non-use, prepare several cups of water (without any coffee) to rinse
the system through completely:

Espresso and cappuccino maker

• Place the filter in the filter holder

• Engage the filter in the filter holder on the left facing the external

marking and turn it firmly to the right

• Place a large enough container under the filter holder.

• Turn steam knob to closed position

• Press “1cup/2cup” button on, then continue to press “ESPRESSO”

button. The pump is then activated. If the boiler (water heating
system) is empty (on first use for example) it will fill with w ater with a
characteristic filling noise. The water contained in the boiler is
evacuated via the steam nozzle.

• AS soon as the water is running out of the filter holder, press

Espresso button off.

• Allow the appliance to finish heating the water.

• Once the “ESPRESSO” light is off, Press “ESPRESSO” button

again, allow 1 cup water to run thr ough; repeat same action to allow
the equivalent of 2 to 3 cups of water to run through.

• Interrupt the process by pressing “ESPRESSO” button agai n.

To rinse the steam nozzle:

• Place a container under it

• Turn the Steam ta p to ‘

’ position.

• Once the “ESPRESSO” light is off. Slowly turn the steam tap to

‘MAX’ direction and allow the steam to escape for about 10 seconds

• Turn steam knob to closed position

• Press “1cup/2cup” button until “1cup/2cup” light off .

Drip coffee maker

Before making your first pot of delicious coffee, we recommend
rinsing the coffee maker by running one or two cycles with water only,
without ground coffee in the filter basket. This will remove any possible
dust which may have settled during shipping.

● Place the filter basket into the basket holder

● Close the top lid.

● Put the glass carafe cup into the warm plate.

● Press “auto/caffe” button on.

● As soon as the water is running out of the filter basket, press

“auto/caffe” button off.

Remove all water from tank, glass carafe and overflow grill after upon
action.
Now you can start to use this machine for making your delicious coffee.

Espresso/Cappuccino
Espresso Coffee

Espresso is much stronger and more aromatic than normal coffee and
is drunk out of small cups called espresso cup s. It is prepa red by forcing
hot water under pressure through ground coffee or pod coffee. This
produces the delightful black coffee with the stimulating effect. Apart
from its characteristic flavour, the hallmark of espresso is the typical
formation of a splendid froth, called crema. This requires a high
pressure and the use of genuine, properly roasted espresso coffee
beans which have been correctly ground.
If you do not purchase ready-ground espresso coffee, grind the coffee
beans in a coffee mill with the setting medium to fine.

• Fill the water tank with fresh water

• Turn the steam tap to the end of the ‘ ’ direction.

• Then press “1cup/2cup” button to select which coffee will be made.

once to select one cup of powder coffee, same time the gre en light
will be illuminated. Twice to select two cups of powder coffee, the
red light will be illuminated. Third to select one cup of pod coffee
will be made, the blue light will be illuminated. Press again will shut
off the produce.

• Continue to press “ESPRESSO” button. The pump is then activated.
The “ESPRESSO” lig h t will be flashed. Wait until a small amount of
water flows out. That means that boiler is full.

• Then press “ESPRESSO” button off, As soon as the system has
reached the required temperature, the “ESPRESSO” light will be
off.

• Preheat the espresso cups on the top housing.

• Insert the appropriate filter into the filter holder.

• Fill with one or two measures spoon of ground coffee and press
down the coffee with the measuring spoon; or place a standard
7g/45mm espresso coffee pod in capsule filter. You should select
the correct filter cup from accessory attachments.

• Insert the filter holder and turn it firmly to the right.

• Place one or two espresso cups beneath the filter holder (Place

one cup if using pods).

• As soon as the “ESPRESSO” light is off, Then press “ESPRESSO”
button on.

• When a sufficient quantity has run through (normally one filter
coffee grounds or one pod can make about 60ml coffee), the
machine will be auto shut off the pump. Otherwise you can press
“ESPRESSO” button to interrupt the produce.

• After making the espresso, remove the filter holder and throw away
the coffee grounds or pod.

The following espresso may be prepared by refilling the filter.

Cappuccino

Steam can be used to make the milk frothy for a cappuccino or for
heating liquids. The temperature required to produce steam being
higher than that necessary to make an espresso, the espresso should
always be prepared first, because otherwise the coffee might be burnt.

FROTHING MILK FOR A CAPPUCCINO

When preparing an espresso, this machine can be used to produce
frothy milk to prepare a cappuccino.

• Pour about 200ml of skimmed milk into a s mall high-sided container,
which will fit beneath the steam nozzle.

• The milk must be nice and fresh and cold, the container must also
be chilled, so do not rinse it in hot water beforehand.

• Press “ESPRESSO” button on.

• Wait until a small amount of water flows out, which means that

boiler is full. Then press “ESPRESSO” button off, the “ESPRESSO”
light will be flashed.

• When the “ESPRESSO” light go off, Turn the steam ta p switch to

“PREPARATION” and steam tap in ‘

’position. And the

“ESPRESSO” light will be illumin ated again.

• When the “ESPRESSO” light go off, Place a container under the
steam nozzle in such a way that it is completely imm ersed in the
milk.

• Turn the tap slowly to ‘MAX’ direction and hold the container steady
during the operation. The nozzle must not touch the bottom of the
container so as not to prevent the steam escaping.

• Once you have obtained the froth (this may need 10-30s), reset the
tap to the end of the ‘ ’ direction and remove the container.

• Then set the tap to ‘MAX’ direction again for a few moments (with
an empty container under the nozzle) to eliminate the residue of
milk in the nozzle.

• Reset the tap to the end of the ‘ ’ direction.

• When this operation is finished, clean the steam nozzle with damp

cloth.

• For the second frothing milk, repeat the steps.

Programming function:

There are three functions that are programmable.

Drip coffee auto-on time setting
Keep warm hour setting
24hr clock setting

Selecting function to program

● Each pressing of the “PROGRAM” button will cycle to next
programming function…
—> drip coffee auto-on time setting function —> keep warm hours
setting function —> 24hr clock setting function —> exit programming
function —>… (repeat cycle)

● Programming the Drip Coffee auto-on time setting function
Press “PROGRAM” button to select the drip coffee auto-on time

setting function.

The 2-digit hours portion o f LCD display will be flashing and the auto

LCD icon will be flashing

Each pressing of the “ARROW UP” or “ARROW DOWN” button will

adjust the hour setting (and alternate between the display of AM or PM
at each passing of 12:00).

Pressing the “PROGRAM” button will confirm and set the displayed

hour and AM or PM setting and…

The 2-digit minutes portion of the LCD display will be flashing and

the auto LCD icon will be flashing.

Each pressing of the “ARROW UP” or “ARROW DOWN” button

will adjust the minute setting.

Pressing the “PROGRAM” button will confirm and set the

displayed minute setting and…

The auto-on fu nction will be on and programmed to automatically

brew at the preset time.

Note: The auto LCD icon will stop flashing and be displayed
steady to indicate that the unit is programmed to automatically brew at
the preset time. The default value in the display will be the last
prog rammed drip coffee auto -on time setting.

The 1-digit keep warm hour will be flashing.(Note: T he default

value will be the last programmed keep warm hours setting..)

● Programming the keep warm hours setting function

Pressing the “ARROW UP” or “ARROW DOWN” button will adjust

the keep warm hour setting.

Pressing the “PROGRAM” button will confirm and set the keep warm

hour setting displayed and…

The 2-digit hours portion of LCD display will be flashing and the clock

LCD icon will be flashing.

● Programming the 24hr clock setting function

Each pressing of th e “ARROW UP” or “ARROW DOWN” button will
adjust the hour setting (and alternate between the display of AM or PM
at each passing of 12:00).

Pressing the “PROGRAM” button will confirm and set t he displayed
hour setting and…

The 2-digit minutes portion of the LCD display will be flashing and
the auto LCD icon will be flashing.

Each pressing of th e “ARROW UP” or “ARROW DOWN” button will
adjust the minute setting.

Pressing the “PROGRAM” button will confirm and set the displayed
minute setting and…

The time of day will be displayed with the colon (:), between hours
and minutes, flashing to indicate the control is not in programming
function and the clock LCD icon will go off.

Drip Coffee Function:

● Auto:

Pressing “AUTO/CAFFE’” button once to turn on auto-brew function,
the unit will be begin brewing at the preset drip coffee auto-on time
setting. The “AUTO/CAFFE” button LED will light and the auto LC D icon
will be flashing while brewing via the auto-brew function. The
“AUTO/CAFFE” button LED will go off and auto LCD icon will disappear
upon completion of the brew cycle.

● Manual:

Pressing “AUTO/CAFFE’” button twice immediately begins the drip

coffee brewing cycle, and press once more to cancel.

The “AUTO/CAFFE’” button LED will light to indicate brewing cycle.

Note: Drip coffee cannot be produced concurrent with the

espresso cycle if desired.

If the “AUTO/CAFFE’” button is pressed at any time while drip coffee
is brewing and the “AUTO/CAFFE’” button LED is lit, the drip coffee
brewing cycle will stop and the “AUTO/CAFFE’” button LED will go off.

Note: In Auto or in Manual function, the unit will automatically go into
keep warm function on completion of brewing cycle and keep warm will
terminate after the preset number of hours.

● Preparing Coffee

The lid of the glass carafe must be properly positioned during the
brewing process.

■ Open the top lid.

■ Pour in the desired quantity of water. Do not fill beyond the MAX

mark on the water container.

■ The divisions on the glass jug and the water level indicator

represent the quantity of fresh water. The eventual amount of coffee
is less , because the coffee meal absorbs some of the water.

■ Put in a filter paper.

■ We recommend using "1 X 4" filter paper. When inserting a paper

filter, make sure the seam is pointing towards the base of the filter
holder. Use your hands to conform the filter to the contours of the
filter basket. This will enable you to achieve better results.

■ Put ground coffee into the filter paper. We suggest using one

measuring spoon of ground coffee for each cup of robust brewed coffee.

After using your coffee machine several times, you can adjust the
quantity to suit your own taste. We do not recommend using coffee that
is ground to a powder-like consist ency, as this will prevent water from
passing through the coffee.

■ Close the lid

■ Place the glass carafe with lid in posit io n on the warming plate.

■ Select to press “AUTO/CAFFE’” button once or twice to make coffee

as you want.

Cleaning

■ Before doing any cleaning, unplug the appliance and allow it to cool
down.

■ The appliance must not be immersed in water for cleaning.

■ Wipe the body of the appliance with a damp cloth.

■ The water tank must be emptied after use.

■ Remove the cup rest grid and clean it.

■ Empty the drip tray and clean it.

The percolation head, the filter holder and the filters must be cleaned
after each use :

■ First, allow the appliance to cool down, and then wipe the percolation
head with a damp cloth.

■ Each detachable element can be rinsed under running water.

■ Do not clean the filter holder or the cup rest grid in the dishwasher.

Important: After making frothy milk, clean the steam nozzle
immediately allowing the appliance to produce steam for 1 to 2 seconds.
Then wipe the tip with a damp cloth. If the pipe and the tip have been
completely obstructed, clean these using a needle.
If necessary, nozzle can be unscrewed using the hexagonal key and
unscrew it in an anticlockwise direction. Clean this part thoroughly.
The nozzle must be screwed back on, and do not over tighten.
Warning: Do not remove or assemble the steam nozzle when it is hot.

DECALCIFYING YOUR 3 IN 1 COFFEE CENTER

Over time mineral deposits build up on internal parts of the coffee maker
and effect the operation of the appliance causing the need for
decalcification. The frequency of decalcification depends on the hardness
of you water and how often the unit is used. Indications that decalcifying is
necessary are:

 Increased noise during production
 Excessive steaming
 Longer brewing times
 The pumping action stop s bef ore al l of the w ater has been pu mpe d fro m

the water reservoir

If usage is regular, decalci fying should be carried out as fol lows:

 With soft water, decalcify once per year
 With medium water, decalcify every t hr ee ( 3) months
 With hard water, decalcify monthly

We recomme nd the use of vinegar for decal cifying.

1. Release all pressure and allow the entire unit to coo l down
completely before decalcifying.

Espresso Maker

2. Pour 230ml of fresh, cool undiluted white household vinegar into
the boiler chamber.

3. Following the lnstruct ions for "Preparing Espresso" run the vinegar
through the espress o ma king cycle e xcept witho ut t he use of coffee
grounds.

4. Place a cup of cool water under the steam wand. When the solution
has pumped through the unit and is at the 2-cup mark on the

espresso carafe, insert the steam wand into t he w ater and ope n t he
boiler valve for 10-15 seconds. Close the boiler valve and allow the
remaining vinegar t o be pumped into the carafe.

5. Repeat the steps above twice using clear cool wat er to rinse any
remaining traces o f v inegar out of the system.

1. Release all pressure and allow the entire unit to cool down
completely before decalcifying.

Coffee maker

2. Pour 600ml of fresh, cool undiluted white household vinegar into
the water reservoir.

3. Following the instruct ions for "Preparing Coffee" run the vinegar
through the coffee making cycle except w it hout the use of coffee
grounds.

4. Repeat the steps above twice using clear cool wat er t o r inse any
remaining traces of vinegar out of the system.

Disposal

Your new product is designed and manufactured with high quality
materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household
waste.
Please dispose of this equipment at your local community waste
collection/ recycling centre. In the European Union there are

separate collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!

This product complies with the requirement of the directives

DECLARAT I ON OF CONF ORMITY

EMC-Directive: 2004 / 108 / EC
Low Voltage Directive: 2006 / 95 / EC
declare that the co f fee maker MORRIS A1608EM is in com pl ianc e with following norms:
EN 61000-3-2
EN 61000-3-3
EN 55014-2
EN 55014-1
EN 60335-2-15
EN 62233
EN 60335-1

Amiridis – Savidis S.A.

EXCLUSIVE IMPORTER IN GREECE:

• 33, Vas. Olgas Street – P.O. 54641 – Thessaloniki, Greece.
Tel: [phone], Fax: [phone]

• 45 Posidonos St. – O.P. 18344 – Moschato, Athens, Greece
Tel: [phone], Fax: [phone]

www.morris.gr / email: [e-mail]