Morphy Richards Supreme Precision 10 in 1 Multicooker Instructions Manual

Page 1
1
MC562000 MUK Rev 2
Please read and keep these instructions for future use
www.facebook.com/morphyrichardsuk
@loveyourmorphy
www.morphyrichards.co.uk/blog
* Register online for your 2 year guarantee. See the back of this instruction book for details (UK and Ireland customers only).
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 1
Page 2
2
In addition, we offer the following safety advice.
Location
Always locate your appliance away from the edge of a worktop.
Ensure that the appliance is used on a firm, flat surface.
Do not use the appliance outdoors, or near water.
Mains Cable
The mains cable should reach from the socket to the base
unit without straining the connections.
Do not let the mains cable hang over the edge of a
worktop where a child could reach it.
Do not let the cable run across an open space e.g.
between a low socket and table.
Do not let the cable run across a cooker or toaster or other
hot area which might damage the cable.
Personal Safety
WARNING: To protect against fire, electric shock and personal injury, do not immerse cord, plug and appliance in water or any other liquid.
WARNING: Avoid contact with moving parts.
Extreme caution must be observed when moving an
appliance with hot contents.
Do not use product with wet or moist hands
Treating Scalds
Run cold water over the affected area immediately. Do not stop to remove clothing, get medical help quickly.
Other Safety Considerations
If the mains lead of this appliance is damaged do not use it.
Telephone Morphy Richards helpline for advice.
The use of accessory attachments not recommended by the
manufacturer may cause damage to the unit.
Do not place the appliance on or near heat sources such as
gas or electric stove, ovens, or burners.
Keep the appliance and the cable away from heat, direct
sunlight, moisture, sharp edges and the like.
When using the unit, ensure the lid is in place before
switching on.
Do not remove the lid until the blades have stopped.
After one operation cycle, you must allow the appliance to
cool down completely, then clean the appliance to prevent burning.
Do not operate the appliance continuously.
Be careful if hot liquid is poured into your Multicooker as it
can be ejected out of the appliance due to sudden steaming.
Electrical Requirements
Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating Current).
WARNING: THIS APPLIANCE MUST BE EARTHED.
Should the fuse in the mains plug require changing a 13 amp
BS1362 fuse must be fitted.
Health And Safety
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
This appliance can be used by persons with reduced physical,
sensory or mental capabilites, or lack of experience and knowledge, if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
The appliance shall not be used by children.
Keep the appliance and cord out of the reach of children.
WARNING: The mixing blades are very sharp. Handle with care
when using and cleaning.
For care and cleaning information, see page 27.
Always disconnect the appliance from the supply if it is left
unattended and before assembly, disassembly or cleaning.
If the supply cable is damaged, it must be replaced with a special
cable assembly available from the manufacturer or its service agent in order to avoid a hazard.
This appliance is not intended to be operated by means of an
external timer or separate remote control system.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 2
Page 3
3
Health And Safety ......................... 2
Introduction ................................... 3
Product Overview ......................... 4
Control Panel ................................ 5
Before First Use ............................ 6
Getting Started .............................. 6
Cookbook ....................................... 6
Automatic Programmes ................. 6
Manual Programmes ..................... 6
To Set-Up Before Use .................... 7
To Attach The Lid ........................... 7
Quick Start Recipes ........................ 8
Using Automatic Programmes ...... 10
Using Manually ............................. 12
Fry or Sauté .................................. 12
Steam ............................................ 13
Boil ................................................ 15
Fast Stew ...................................... 16
Mix ................................................. 18
Blend ............................................. 19
Chop .............................................. 20
Emulsify ......................................... 22
Melt ................................................ 22
Stir ................................................. 24
Jug ................................................ 25
Feature Overview .......................... 25
Accessories .................................. 26
Lock Ring ..................................... 27
Care And Cleaning ....................... 27
Error Codes .................................. 28
Troubleshooting ........................... 28
Contact Us ................................... 29
Notes ............................................ 30
Guarantee ..................................... 32
Contents
T
hank you for your recent purchase of the Morphy Richards Supreme Precision 10 in 1 Multicooker.
Please read this instruction booklet carefully before you use your new Multicooker for the first time.
Y
our Multicooker is designed to allow you to produce a wide range of dishes with minimum fuss. The automatic programmes allow you to make perfect risotto and pasta dishes everytime without having to k
eep a watchful eye over a pan on the hob. It really couldn’t be easier!
Remember to visit www.morphyrichards.co.uk to register your product’s two year guarantee.
Introduction
To get the most out of your new Multicooker, please read these instructions thoroughly before use.
Note
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 3
Page 4
4
7
1
3
4
2
6
1
0
1
1
1
2
13
1
5
1
4
8
9
5
2
1
6
17
Features
(1) Measuring Cap
(2) Lid
(3) Handle
(4) Jug
(5) Main Unit
(6) Jug Release Button
(7) Cable Socket
(on side)
(8) Control Panel (19-35)
(9) On/Off Switch
(10) Steaming Basket
(11) Mixing Paddle
(12) Serrator Blade
(13) Chopping Blade
(14) Drive Shaft
(15) Lock Ring
(16) Lid Gasket
(17) Blade Cover (X2)
(18) Spatula
(not shown)
(19) Mains Lead
(not shown)
(20) Cleaning Brush
(not shown)
Product overview
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 4
Page 5
5
Features
Control Panel
2
2
3
0
2
9
3
1
3
2
36
37
3
4
3
3
3
5
2
7
2
8
2
6
2
5
2
3
2
1
2
4
(21) Mode Button
(22) Standby Button
(23) Pulse Button
(24) Start Button
(25) Increase Button
(26) Decrease Button
(27) Timer Button
(28) Temperature Button
(29) Mixing Speed Button
(30) Stop Button
(31) Temperature Icon(s)
(32) Timer Icon
(33) Lid Lock Icon(s)
(34) Mixing Speed Icon(s)
(35) Automatic Programme
A Icon
(36) Automatic Programme
B Icon
(37) Pulse Icon
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 5
Page 6
6
I
t is important to clean your Multicooker before first use or if it has not been used for a long period of time. See the ‘Care and cleaning’ s
ection on page 27 for more information.
Unpack your Multicooker and remove any
c
ardboard inserts or labels from the product.
Remove the Blade Covers (17) from the Serrator
B
lade
(
12)and Chopping Blade(13).
WARNING: BLADES ARE SHARP
Wash the Measuring Cap (1), Lid (2), Mixing
Paddle
(11) Steaming Basket (10), Blade Covers
(17) and Spatula (18) in warm soapy water.
Wash the Chopping and Serrator Blades (12),
(13) using the Cleaning Brush (20) and holding
them from the top to avoid cutting yourself.
Rinse the inside of the Jug (4) with warm soapy
water. Ensure the contacts on the bottom of the Jug are dry before first use.
With a damp cloth clean the Main Unit.
Carefully dry all the washed parts.
WARNING
DO NOT MOVE YOUR MULTICOOKER WHILE
IN USE.
DO NOT USE METAL UTENSILS IN THE MULTICOOKER, DOING SO MAY DAMAGE THE COOKING SURFACE.
New kitchen appliances can often seem daunting
when you start to use them for the very first time. Your new Multicooker is much easier to use than it may look at first glance. To help you understand the process better, we have included a step by step process for a mushroom risotto recipe on the automatic setting (page 8), and a bechamel sauce on the manual (page 9). For more recipes you can make in your new Multicooker, see the cookbook included in the box.
T
he cookbook supplied with your new Multicooker contains recipes for both the automatic and manual programmes. We r
ecommend trying a couple of the recipes to ‘test’ your Multicooker and to help understand its f
unctions and capabilities.
Your Multicooker has 2 automatic settings.
They have been designed with the ideal
temperatures, mixing speeds and times to produce perfect rice and pasta dishes every time. How to use the automatic programmes is explained on page 10.
During each programme, your Multicooker will
beep at selected points. When instructed by your Multicooker, add the required ingredients to the Jug
(4). Refer to the cookbook supplied with your
Multicooker for recipes and what should be added at which interval in the selected programme.
Your Multicooker utilises 2 main processes mixing
and heating. These coupled with the timer, allow you to use your Multicooker for a wide range of tasks in the kitchen.
When you have started to get to grips with your
Multicooker, you will be able to create and adapt your own recipes. The supplied cookbook also includes a variety of delicious dishes you will be able to make with ease.
Please read this manual fully before using your
Multicooker.
At certain points, to aid cooking it may be
required to scrape the sides of Jug with a spatula to remove any food adhered to the surface.
Before First Use
Getting Started
Cookbook
Automatic Programmes
Manual Programmes
Note
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 6
Page 7
7
4
Plug your Multicooker into the mains.
3
Insert the Jug into the Main Unit. Press down firmly to lock into place.
2
Ensure the Drive Shaft (14) is correctly locked into the Jug (4) using the Lock Ring (15) located on the base of the Jug. Turn the Lock Ring clockwise to secure before using your Multicooker. The Drive Shaft should not be loose.
1
Place the Main Unit (5) on a flat, stable surface away from the worktop edge. Ensure your Multicooker is secure and stable before use.
1
Attach the Lid (2), place on top of the Jug with the handle located within the cutout on the Lid. Press down and twist clockwise to lock into place.
To Attach the Lid
To Set-Up Before Use
2
When your Multicooker is switched on, if the Lid is not correctly attached to the Jug the Mixing Speed (29) and Pulse (23) Buttons will not be illuminated, and the ‘unlocked’ Lid Lock Icon (33) will be illuminated.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 7
Page 8
8
Method:
Ensure the Drive Shaft (14) and Lock Ring (15) are correctly
located and locked into place in the Jug (4).
Insert the Jug into the Main Unit (5).
Place the Mixing Paddle (11) onto the Drive Shaft.
Add the oil, shallot, white onion, garlic, button and shiitake
mushrooms to the Jug.
Place the Lid (2) on the Jug, press down and twist clockwise to
lock into place. Insert the Measuring Cap (1) into the Lid.
Switch your Multicooker on (9).
Press the Mode Button (21) once to select programme A (risotto).
The Automatic Programme A Icon will illuminate (35)
Press the Start Button (24). Your Multicooker will begin to cook.
After 5 minutes your Multicooker will beep twice. Remove the Lid
and Measuring Cap. If required, scrape the sides of the Jug with a silicone spatula.
Add the risotto rice to the Jug, after 1 minute add the wine, water
and crumble in the stock cube. Replace the Lid, without the Measuring Cap.
After 10 minutes your Multicooker will beep three times. Remove
the Lid and add the cream. Replace the Lid.
After 8 minutes your Multicooker will beep four times. Remove the
Lid and add the butter and Parmesan cheese. Replace the Lid.
After 4 minutes your Multicooker will beep and Display ‘End’.
Your risotto is ready.
Carefully twist the Lid anticlockwise and remove, being careful
about any hot steam that will escape (angle the Lid away from you for safety). Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker.
Give the risotto a stir with a spatula or wooden spoon before
serving.
We understand that using a product that appears complicated for the first time can often b
e a daunting experience. Using your new product ‘hands on’ can often be the best way
to learn how to use it.
S
o to help, we have included these recipes; mushroom risotto on the automatic setting and bechamel sauce on the manual. When you have got to grips with your new Multicooker there are more recipes and dishes for you to try on both the automatic and m
anual settings in the cookbook supplied with the product.
For more information on how to use your Multicooker on the Automatic setting, see page
10.
Ing
re
die
nts:
4
0
ml
Ext
r
a
v
i
rgi
n
ol
i
v
e
oi
l
3
0
g
Sh
al
l
ot
,
f
i
n
el
y
c
h
oppe
d
2
0
g
W
h
i
t
e
on
i
on
f
i
n
el
y
c
h
oppe
d
1
Gar
l
i
c
c
l
ov
e
,
f
i
n
e
l
y
c
h
oppe
d
2
0
0
g
Bu
t
t
on
mu
s
h
r
ooms
,
di
c
e
d
15
0
g
Sh
i
i
t
ak
e
mu
s
h
r
ooms
,
di
c
e
d
3
0
0
g
Ri
s
ot
t
o
r
i
c
e
4
0
ml
Dr
y
w
h
i
t
e
w
i
n
e
6
3
0
ml
W
a
t
er
1
Ve
ge
t
a
bl
e
s
t
oc
k
cu
be
5
0
ml
Dou
bl
e
cr
e
a
m
4
0
g
Bu
t
t
e
r
3
0
g
P
a
r
me
s
a
n
c
h
ee
s
e
,
gr
a
t
ed
Automatic - Mushroom Risotto
Quick Start Recipe
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 8
Page 9
9
Your new Multicooker utilises 2 main processes, mixing and heating. Coupled with a timer t
his allows you to use your Multicooker for a wide range of processes within your kitchen.
How to set up your Multicooker for the different processes are detailed on pages 12-24.
T
he test recipe below for making a bechamel sauce requires you to set the timer, heating and mixing functions. When you have got to grips with programming the manual settings, you can try many more of the manual recipes supplied within the cookbook, or adapt your o
wn recipes for use within your Multicooker.
Manual - Bechamel Sauce
Method:
Ensure the Drive Shaft (14) and Lock Ring (15) are correctly
located and locked into place in the Jug (4).
Insert the Jug into the Main Unit (5).
Place the Mixing Paddle (11) onto the Drive Shaft.
Add all the ingredients (listed left) into the Jug.
Place the Lid (2) on the Jug, press down and twist clockwise to
lock into place. Insert the Measuring Cap (1) into the Lid.
Switch your Multicooker on (9).
Press the Mixing Speed Button (29), Use the Increase and
Decrease Buttons
(25),(26) to set the Mixing Speed Icon (34) to
speed 3. The ‘3’ will be flashing.
Press the Temperature Button (28), Use the Increase and Decrease
Buttons to set the Temperature Icon (31) to 80°C. The ‘80’ will be flashing.
Press the Timer Button (27) once (to set the minutes section). Use
the Increase and Decrease Buttons to set the Timer Icon (32) to 10 minutes. The display will read ‘10:00’.
The Control Panel (8) should have 10 Minutes, 80°C and Speed 3
selected (flashing).
Press the Start Button (24). Your Multicooker will beep and start.
After 10 minutes your Multicooker will beep and Display ‘End’.
Your bechamel sauce is ready.
Carefully twist the Lid anticlockwise and remove, being careful
about any hot steam that will escape (angle the Lid away from you for safety). Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker.
Give the sauce a stir with a wooden spoon and enjoy.
Ingredients:
500ml Whole milk
50g Butter
40g Plain flour
4g Salt
Nutmeg, to taste
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 9
Page 10
10
6
Press the Mode Button (21) to highlight programme A (Risotto) (35). Press again to cycle through Mode B (Pasta)
(36) and back to
the manual setting. The designated letter, A or B will be displayed on the Control Panel.
5
The Control Panel (8) will illuminate and your Multicooker will sound.
If the Control Panel is not lit, press the Standby Button
(22).
4
Switch your Multicooker On (9).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Mixing Paddle (11) onto the Drive Shaft (14).
3
Attach the Lid (2), Place the Measuring Cap
(1) into the space in the Lid (if stated to do so
in the recipe).
2
Refer to the selected recipe and add the first set of ingredients to the Jug (4).
Using Automatic Programmes
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 10
Page 11
11
8
After 5 minutes your Multicooker will beep twice, this is the first prompt to add the next set of ingredients listed in the recipe. Remove the Lid, add the Ingredients and replace the lid. Your Multicooker will continue to cook.
7
Press the Start Button (24), your Multicooker will begin to cook.
9
Your Multicooker will prompt another 2 times during the cooking process to add more ingredients (times vary by programme). Refer to the cookbook to add the correct ingredients to the Jug.
10
When finished, your Multicooker will sound and display ‘END’. Your Multicooker will slow to speed 1 and continue mixing to prevent food from sticking to the base of the Jug. Press the Stop Button (30).
11
Remove the Lid by twisting anticlockwise and then lifting away from the Jug. Angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker.
Carefully remove the Mixing Paddle from the Jug. WARNING HOT STEAM
12
Press the Jug Release Button (6) and remove the Jug from the Main unit before serving.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 11
Page 12
12
4
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a slow speed (1-2) to stir the food while frying and prevent sticking.
2
Add your ingredients to the Jug and attach the Lid (2).
4
Press the Timer Button (27) (if using) and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds. You can use your Multicooker without setting the timer for a maximum of 30 minutes.
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Mixing Paddle (11) onto the Drive Shaft (14).
Fry or Sauté
Using Manually
For use in recipes like cottage pie.
The 10 main functions are explained here,
f
rying/sautéing, steaming, boiling, fast stewing, mixing, blending, chopping, emulsifying, melting a
nd stirring.
When you have used your Multicooker a few
t
imes, you will be able to adapt recipes and
create your own delicious dishes.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 12
Page 13
13
5
Press the Temperature Button (28), the Temperature Icon (31) will flash. Use the Increase and Decrease Buttons to adjust the temperature in celsius up to 100°C.
7
When finished, your Multicooker will sound and display ‘END’. Your Multicooker will slow to speed 1 and continue mixing to prevent food from sticking to the base of the Jug. Press the Stop Button
(30).
8
Remove the Lid by twisting anticlockwise and then lifting away from the Jug. Angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Mixing Paddle from the Jug. WARNING HOT STEAM
Steam
6
Press the Start Button (24). Your Multicooker will sound and begin the cooking process.
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Fill the Jug (4) to the steaming icon marked on the side with cold water (300ml). Do not fill past this level. This is enough water to steam for 60 minutes. Attach the Lid
(2).
2
Switch your Multicooker on. Your Multicooker will illuminate and sound. Press the Temperature Button
(28), the Temperature
Icon (31) will flash. Use the Increase and Decrease Buttons (25),(26) to adjust the temperature to 100°C.
For use in recipes like carrots in parsley butter.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 13
Page 14
14
5
When the water has reached 100°C, (the icon will stop flashing). Press the Stop Button (30) and remove the Lid. Place the Steaming Basket
(10) into the Jug. Add the ingredients
to the Steaming Basket.
6
Replace the Lid, reset the temperature to 100°C and set the timer for the correct length to cook the ingredients in the Steaming Basket. (As per steps 2-4).
8
After cooking, remove the Lid angling away from you, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Steaming Basket from the Jug.
WARNING HOT STEAM
3
Press the Timer Button (27) and use the Increase and Decrease buttons to adjust the timer. Set your Multicooker to 10 minutes to bring the water to a boil.
4
Press the Start Button (24). Your Multicooker will begin to heat the water, bringing it to a boil.
7
Press the Start Button (24). When finished, your Multicooker will sound and display ‘END’, Press the Stop Button (30).
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 14
Page 15
15
Boil
4
Press the Mixing Speed Button (29) (if using), the Icon (34) will flash. Use the Increase and Decrease Buttons (25),(26) to adjust the speed setting. Use a slow speed (1-2) to stir the food while boiling.
5
Press the Timer Button (27) (if using), and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds. You can use your Multicooker without setting the timer for a maximum of 30 minutes.
5
Press the Temperature Button (28), the Icon
(31) will flash. Use the Increase and Decrease
Buttons to adjust the temperature in celsius to 100°C.
6
Press the Start Button (24). Your Multicooker will sound and begin the cooking process. the °C selected on the LCD display will flash until it has reached the desired temperature.
2
Add your ingredients and water to the Jug
(2) and attach the Lid.
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Mixing Paddle
(11) onto the Drive Shaft (14).
F
or use in recipes like pasta & borlotti beans.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 15
Page 16
16
Fast Stew
4
Press the Mixing Speed Button (29) the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a slow speed (1-2) to stir the food while stewing to prevent sticking.
2
A
d
d
y
o
u
r
i
n
g
r
e
d
i
e
n
t
s
t
o
t
h
e
J
u
g
(
4
)
a
n
d
a
t
t
a
c
h
t
h
e
L
i
d
(
2
)
.
1
F
o
l
l
o
w
t
h
e
s
t
e
p
s
i
n
T
o
S
e
t
-
U
p
B
e
f
o
r
e
U
s
e
t
o
s
e
t
-
u
p
y
o
u
r
M
u
l
t
i
c
o
o
k
e
r
.
P
l
a
c
e
t
h
e
M
i
x
i
n
g
P
a
d
d
l
e
(
1
1
)
o
n
t
o
t
h
e
D
r
i
v
e
S
h
a
f
t
(
1
4
)
.
3
Insert the Measuring Cap (1) into the space in the Lid.
For use in recipes like beef & lentil stew
7
When finished, your Multicooker will sound and display ‘END’. If you are using a mixing function, your Multicooker will slow to speed 1 and continue mixing to prevent food from sticking to the base of the Jug. Press the Stop Button (30).
8
Remove the Lid by twisting anticlockwise and then lifting away from the Jug. Angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Mixing Paddle from the Jug (if using). WARNING HOT STEAM
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 16
Page 17
17
6
Press the Timer Button (27) (if using), the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds. You can use your Multicooker without setting the timer for a maximum of 30 minutes.
8
If required, during stewing, remove the Lid to boil off any excess liquid. With the Lid removed your Multicooker will not stir, so you will need to stir manually using a plastic spatula to prevent food sticking to the Jug.
9
When finished, your Multicooker will sound and display ‘END’, Press the Stop Button
(30). Your Multicooker will slow to speed 1
and continue mixing to prevent food from sticking to the base of the Jug.
10
Remove the Lid by twisting anticlockwise and then lifting away from the Jug. Angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Blade or Paddle from the Jug (if using). WARNING HOT STEAM
7
Press the Start Button (24). Your Multicooker will sound and begin the cooking process.
5
Press the Temperature Button (28), the Icon
(31) will flash. Use the Increase and Decrease
Buttons to adjust the temperature in celsius to 100°C.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 17
Page 18
18
4
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a medium speed (5-6).
3
Insert the Measuring Cap (1) into the space in the Lid.
5
To set the timer, press the Timer Button (27) and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds.
6
Press the Start Button (24). Your Multicooker will sound and begin to mix.
Mix
2
Add your ingredients to the Jug (4) and attach the Lid (2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Chopping Blade (13) onto the Drive Shaft (14).
For use in recipes like buttercream.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 18
Page 19
19
Blend
4
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a high speed (9-10).
2
Add your ingredients to the Jug (4) and attach the Lid (2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Chopping Blade (13) or Serrator Blade (12) (if using frozen or tough ingredients), onto the Drive Shaft
(14).
3
Insert the Measuring Cap (1) into the space in the Lid.
7
When finished, your Multicooker will sound and display ‘END’. Press the Stop Button
(30)
For use in recipes like raspberry smoothie.
8
If required, remove the Lid and add the next set of ingredients to the Jug before repeating the process.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 19
Page 20
20
7
Alternatively, Press the Pulse Button (23) to blend in short bursts at speed 10.
8
When finished, your Multicooker will sound and display ‘END’. Press the Stop Button (30) and remove the Lid.
Chop
2
Add your ingredients to the Jug (4) and attach the Lid
(2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Chopping Blade
(13) onto the Drive Shaft (14).
For use in recipes like pesto.
5
To Set the Timing Function, (if using)
Press the Timer Button (27) and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds. We do not recommend blending for longer than 1 minute.
6
Press the Start Button (24). Your Multicooker will sound and begin to blend.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 20
Page 21
21
4
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a high speed (7-8).
3
Insert the Measuring Cap (1) into the space in the Lid.
5
Press the Timer Button (27) and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds.
6
Pr
e
s
s
t
h
e
St
a
rt
B
u
t
t
on
(
2
4
).
Y
ou
r
Mu
lt
ic
ook
e
r
will
s
ou
n
d
a
n
d
be
gin
t
o
ch
op.
7
Alternatively, Press the Pulse Button (23) to chop in short bursts at speed 10. In-between bursts you may need to scrape the sides of the jug down using a spatula.
8
When finished, your Multicooker will sound and display ‘END’. Press the Stop Button (30) and remove the Lid.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 21
Page 22
22
3
Insert the Measuring Cap (1) into the space in the Lid.
4
P
r
e
s
s
t
h
e
P
u
l
s
e
B
u
t
t
o
n
(
2
3
)
t
o
e
m
u
l
s
i
f
y
t
h
e
o
i
l
i
n
s
h
o
r
t
b
u
r
s
t
s
a
t
s
p
e
e
d
1
0
.
I
n
b
e
t
w
e
e
n
b
u
r
s
t
s
y
o
u
m
a
y
n
e
e
d
t
o
s
c
r
a
p
e
t
h
e
s
i
d
e
s
o
f
t
h
e
j
u
g
d
o
w
n
u
s
i
n
g
a
s
p
a
t
u
l
a
.
Melt
2
Add your ingredients to the Jug (4) and attach the Lid (2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Mixing Paddle (11) onto the Drive Shaft (14).
For use in recipes like carrots in parsley butter.
Emulsify
2
Add your ingredients to the Jug (4) and attach the Lid (2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Chopping Blade
(13) onto the Drive Shaft (14).
F
or use in recipes like salad dressing.
562000 Rev2.qxp_Layout 1 19/01/2015 09:24 Page 22
Page 23
23
3
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a slow speed to stir the food while melting and prevent sticking (1-2).
5
Press the Timer Button (27), (if using), and the first half of the Timer (32) will flash. Use the Increase and Decrease Buttons to adjust the timer in minutes. Press the Timer Button again, the second half of the Icon will flash, use the Increase and Decrease buttons to adjust the timer in seconds. You can use your Multicooker without setting the timer for a maximum of 30 minutes.
4
Press the Temperature Button (28), the Icon
(31) will flash. Use the Increase and Decrease
Buttons to adjust the temperature in celsius to a medium heat, 50 or 60°C.
7
When finished, your Multicooker will sound and display ‘END’. Your Multicooker will slow to speed 1 and continue mixing to prevent food from sticking to the base of the Jug. Press the Stop Button
(30).
8
Remove the Lid by twisting anticlockwise and then lifting away from the Jug. Angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Mixing Paddle from the Jug (if using).
6
Press the Start Button (24). Your Multicooker will sound and begin the cooking process. The °C selected on the LCD display will flash until it has reached the desired temperature.
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 23
Page 24
24
3
Press the Mixing Speed Button (29), the Icon
(34) will flash. Use the Increase and Decrease
Buttons (25),(26) to adjust the speed setting. Use a medium speed (5).
5
Press the Start Button (24). Your Multicooker will sound and begin to stir.
6
When finished, your Multicooker will sound and display ‘END’. Press the Stop Button (30) and remove the Lid.
Stir
2
Add your ingredients to the Jug (4) and attach the Lid (2).
1
Follow the steps in ‘To Set-Up Before Use’ to set-up your Multicooker. Place the Mixing Paddle (11) onto the Drive Shaft (14).
F
or use in recipes like rice pudding.
4
(If using), press the Temperature Button (28), the Icon (31) will flash. Use the Increase and Decrease Buttons to adjust the temperature to the required setting.
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 24
Page 25
25
The Jug will get hot during use.
The Jug is not suitable for use in the oven,
microwave, freezer or dishwasher.
You can cook in the Jug without the Lid (2)
attached. For safety reasons, the Pulse (23) and Speed (29) settings will be disabled with the lid removed. You may need to stir the food in the Jug manually.
Standby
After turning your Multicooker on if not used for a
few minutes it will automatically go into standby mode. Press the Standby Button (22) to use your Multicooker.
Pause
During use, if you need to open the Lid (2) to
check progress or add seasoning, press the Start Button
(24) to pause the cooking process. Press
the Start Button again to continue. If after 20 minutes the Start Button has not been pressed, or the programme has not been cancelled by pressing the Stop Button (30), your Multicooker will automatically continue.
If you remove the Lid without pausing, the mixing
function will stop automatically for safety reasons. The heating and timer functions will continue as standard. The mixing function will not continue until the Lid has been correctly replaced.
Warming Up
When adapting your own recipes for use in your
Multicooker, you will need to allow time for your Multicooker to reach the selected temperature. The timing function will start counting down from the beginning, not when the jug reaches temperature. While your Multicooker is reaching temperature, the ‘ºC’ Temperature Icon
(31) will
flash. When the selected temperature is reached, the icon will cease flashing. If heating to 100ºC the Icon will continue flashing throughout the cooking process as the heating element will be constantly on to maintain the high temperature.
Mixing/Chopping
Your Multicooker provides continuous mixing
from low speeds (ideal for constant stirring), to high speed (chopping/whisking). It also features a Pulse Button (23) allowing for high speed bursts to chop or mix for short periods of time.
Very hard foods such as nuts or lump sugar
should not be any bigger than 1.5cm in diameter. Softer items, such as fruits and vegetables can be larger.
Your Multicooker is not suitable for chopping
hard ingredients such as coffee beans.
Frozen fruits should be defrosted for 10-15
minutes before processing with the supplied Serrator Blade
(12).
Your Multicooker is also not suitable for kneading
heavy dough mixtures (bread, pasta, pastry etc.)
The Attachments for use with the Mixing process
are the Mixing Paddle (11) Serrator (12) and Chopping Blade (13). For ideal usage see the Accessories section on page 26.
Feature Overview
Jug (4)
7
R
emove the Lid by twisting anticlockwise and then lifting away from the Jug. If using the heating element, angle the Lid away from you when lifting, the contents will be hot. Allow the water collected on the inside of the Lid to fall back into the Jug, to avoid drips onto your Multicooker. Carefully remove the Mixing Paddle from the Jug.
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 25
Page 26
26
Heating
The heating element within your Multicooker can
h
eat the Jug from 37°C to 100°C. Your
Multicooker is not suitable for deep frying.
3
7
º
C T
o heat to body temperature.
50ºC-60ºC For warm milk or delicate foods that
w
ould burn or separate at a higher temperature,
such as chocolate or butter.
70ºC-80ºC To heat milk, melt cheese or dissolve
s
ugar. For cooking sauces, creams or puddings
m
ade with eggs.
90ºC-100ºC To pan fry, simmer, boil or steam.
Heating in the Jug (4) is usually combined with
the mixing function to prevent food from sticking to the bottom of the Jug.
Using the heating function and the supplied
Steaming Basket
(10) you can use your
Multicooker as a steamer.
Note: you can heat without the Lid (2) attached,
but for safety the mixing function will be disabled. The Mixing Speed Button (29) will only illuminate on the Control Panel
(8), when the Lid is correctly
attached to the Jug.
While your Multicooker is reaching temperature,
the ‘ºC’ Temperature Icon (31) will flash. When the selected temperature is reached, the icon will cease flashing. If heating to 100ºC the Icon will continue flashing throughout the cooking process as the heating element will be constantly on to maintain the high temperature.
Pulse
To use the Pulse function, ensure the Blade (12)
or (13), Lid (2) and Measuring Cap (1) are properly attached. Press and hold the Pulse Button (23) for 2-3 seconds and release.
You can use the Pulse function repeatedly until
the desired consistency is achieved.
The Pulse setting cannot be used while a preset
programme is running, or while your Multicooker is heating.
Timer
The maximum time that may be set on the timer
is 60 minutes.
Adjusting Manual Settings
You can change the mixing speed, cooking
temperature or timer while your Multicooker is in use manually. Press the desired function button, (either the Timer (27), Temperature (28) or Mixing Speed (29) Button), The corresponding icon will flash on the Control Panel
(8) and you can use the
Increase and Decrease Buttons (25),(26) to amend the setting.
Y
our Multicooker comes with a Measuring Cap, Steaming Basket, Mixing Paddle, 2 Blades and Spatula. Each are used for different purposes.
Measuring Cap (1)
The Measuring Cap supplied with your Multicooker has 2 uses:
It is a 40ml measuring cap, ideal for measuring
liquids, such as oil or wine.
It also acts as a ‘cap’ to the Lid (2).
With the cap removed from the Lid, the Lid acts similar to when a lid is partly covering a pan on the stove, allowing the steam to escape.
With the Measuring Cap in place, the Lid acts like a closed pan lid, trapping the steam and moisture within the Jug (4).
Note: the Measuring Cap should always be
attached to the Lid when you are blending or mixing at high speed in the Jug. When the Jug is full, blending at high speed can cause liquid to be ejected from the Measuring Cap hole in the Lid if the Measuring Cap is not in place.
Steaming Basket (10)
For steaming vegetables or other foods within your Multicooker. Follow the instructions on page 13 for use.
Mixing Paddle (11)
The mixing paddle is used to mix or stir foods while cooking in the jug. It should not be used with the Pulse Function or on speeds above 5 to avoid splashing and vibration.
Speed 1-3 For mixing food gently during
cooking without damage or breaking up. (rice, mushrooms, vegetables etc).
Speed 4-5 For emulsifying and mixing sauces.
Serrator Blade (12)
The Serrator blade is for use with frozen fruit (after defrosting for 10-15 minutes) or ice and should be used only with the Measuring Cap (1) inserted into the Lid (2) to prevent splashing.
Speed 6-10 / Pulse For crushing ice, frozen
fruit or for ice cream.
Accessories
40ml
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 26
Page 27
27
Chopping Blade (13)
The Chopping Blade is ideal for use with a wider r
ange of foods than the Serrator blade, at higher
speeds it should be used with the Measuring Cap
(1)i
nserted into the Lid (2)to prevent splashing.
Speed 4-5 For mixing cake mix,
whisking/mixing batters etc.
Speed 6-8 For blending various foods.
Speed 9-10 For chopping hard, dry food (e.g.
P
armesan cheese, biscuits or dry bread), or for
blending or mixing.
Pulse For chopping foods while controlling the
size of the dice.
Spatula (18)
During normal use, food may adhere to the sides of the Jug. It may be necessary to scrape the sides of the Jug down partway through cooking using a silicone spatula, wooden spoon or the plastic spatula supplied with your Multicooker.
DO NOT USE METAL UTENSILS IN THE MULTICOOKER, DOING SO MAY DAMAGE THE COOKING SURFACE.
The Drive Shaft (14) within the Jug can be
removed for ease of cleaning and to prevent food from sticking underneath the seal within the base of the Jug (4). The Drive Shaft is locked into place using a Lock Ring (15).
To remove:
1. ENSURE THERE ARE NO ATTACHMENTS IN
THE JUG, AND THE JUG IS COOL TO TOUCH.
2. Turn the Jug upside down and turn the lock ring
anti clockwise.
3. After the first ‘click’ hold the drive shaft and
continue to twist the Lock Ring 45 degrees and remove. The Drive Shaft can now be removed from the Jug for cleaning.
To replace insert the Drive Shaft into place and
replace the Lock Ring underneath the Jug. Twist clockwise until it ‘clicks’ and the Drive shaft is locked into place.
A
llow the Jug(4) and any accessories used to
cool completely before cleaning.
T
he Lock Ring (15)and Drive Shaft (14)can be
removed as detailed above for easy cleaning.
I
f any residue remains in the Jug, with the Drive
S
haft in place, insert hot soapy water and leave to
soak for 15 minutes.
I
mportant: Do not submerge the outer base of
the Jug in water.
If attached, remove the Blade Covers (17) from
the Serrator Blade (12) and Chopping Blade (13).
WARNING: BLADES ARE SHARP
Wash the Measuring Cap (1), Lid (2), Mixing
Paddle (11) Steaming Basket (10), Lid Gasket
(16), Blade Covers (17) and Spatula (18) in warm
soapy water. Wash the Serrator and Chopping Blades
(12), (13) using the Cleaning Brush (20)
and holding them from the top to avoid cutting yourself.
Carefully wash the inside of Jug (4) and Drive
Shaft (14) with warm soapy water.
Dry carefully.
DO NOT SUBMERGE THE JUG IN WATER OR
WET THE CONTACTS ON THE BOTTOM OF THE JUG.
Wipe the Main unit with a damp cloth.
Dry carefully all the washed parts.
No parts are dishwasher safe.
Replacing the Lid Gasket (16)
During cleaning you may need to remove the Lid
Gasket from the Lid. Simply grip the silicone Lid Gasket and gently pull to remove.
To replace, ensure the arrows that are moulded
on the Lid Gasket are directed towards the lid. Push around the outside of the moulded ring on the underside of the Lid, until fully located in the groove.
The Lid Gasket may discolour during use.
This is normal.
Care And Cleaning
Lock Ring
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 27
Page 28
28
E
1
T
he motor is overloaded.
R
educe the amount of food in
the Jug
(4).
R
emove any food residue from
the Paddle
(11), or Blades
(
12),(13)
.
Error Code Cause Solution
The device doesn't work. Your Multicooker is not
connected to the mains.
The Mains Lead (19) is not
properly connected to the Cable Socket
(7) on the Main Unit (5).
The On/Off Switch (9) is set to
off or your Multicooker is in standby.
Plug the Mains Lead (19) into
the socket on the wall.
Switch the On/Off Switch (9) to
off, and insert the Mains Lead into the Cable Socket.
Switch the On/Off Switch on, or
press the Standby Button (22).
Problem Issue Solution
E
3
T
he Jug (4) is not correctly
inserted into the Main Unit
(5).
The Jug was removed during
use.
I
nsert or replace the Jug into
the Main Unit.
E5 The Motor burn out safety
switch has switched on.
Let your Multicooker cool down
for at least 30 minutes. If the problem persists after cooling down, contact Morphy Richards.
Error Codes
Troubleshooting
The buttons (21)-(30) do not
react immediately.
The buttons on the Control
Panel (8) require the right contact time.
Touch or press the buttons for a
longer period.
Water is leaking from the Lid (2) The Lid Gasket (16) is not
attached correctly.
The Lid Gasket in the Lid is
damaged
Check the Lid Gasket on the
underneath of the Lid is in place and correctly attached.
Contact Morphy Richards.
The Lid (2) is open but the Lid
Lock Icon (33) on the Control Panel (8) shows the closed padlock.
There is some food in the
sensor at the top of the Jug Handle (3) or on the Main Unit
(5).
Remove any food residue left
on/in your Multicooker, if the problem persists, do not use. Contact Morphy Richards.
The programme has stopped
before the end.
Your Multicooker has lost power
temporarily.
Switch the On/Off Switch (9) to
off, and check the Mains Lead. Continue the recipe using the manual settings.
The Mixing or Pulse functions
are not working.
The Lid is not correctly attached
to the Jug.
These functions are not
available during this part of the process.
Correctly attach the Lid to the
Jug.
Do not try to use.
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 28
Page 29
29
Helpline
If you are having a problem with your appliance, p
lease call our Helpline, as we are more likely to be able to help than the retailer you purchased t
he item from.
Please have the product name, model number a
nd serial number to hand when you call to help us deal with your enquiry.
U
K Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk To Us
If you have any questions or comments, or want some great tips or recipe ideas to help you get the most out of your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact us
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 29
Page 30
30
Notes
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 30
Page 31
31
Notes
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 31
Page 32
32
MC562000 MUK Rev 2 01/15
The After Sales Division Morphy Richards Ltd Mexborough, South Yorkshire, England, S64 8AJ
Helplines (office hours) UK 0344 871 0944 Spare Parts 0344 873 0710 Republic of Ireland 1800 409 119 www.morphyrichards.com
Y
our standard one year guarantee is extended for an additional 12 months when you register the product within 28 days of purchase with Morphy Richards. If you do not r
egister the product with Morphy Richards within 28 days,
y
our product is guaranteed for 1 year. To validate your 2
y
ear guarantee register with us online at
w
ww.morphyrichards.co.uk
Or call our customer registration line
U
K 0344 871 0242
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with M
orphy Richards individually.
Please note that the 2 year guarantee is only available in the UK and Ireland. Please refer to the one year guarantee for more information.
It is important to retain the retailer’s receipt as proof of purchase. Staple your receipt to this back cover for future reference.
Please quote the following information if the product develops a fault. These numbers can be found on the base of the product.
Model no.
Serial no.
All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of original purchase, you should contact the Helpline number quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions), the faulty appliance will then be repaired or replaced as appropriate and dispatched usually within 7 working days of receipt.
If, for any reason, this item is replaced or repaired during the 1 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must have been used according to the instructions supplied.
Morphy Richards shall not be liable to replace or repair the g
oods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, misuse, negligent use or used contrary to the m
anufacturer’s recommendations or where the fault has
b
een caused by power surges or damage caused in
transit.
2 T
he appliance has been used on a voltage supply other
t
han that stamped on the products.
3 Repairs have been attempted by persons other than our
service staff (or authorised dealer).
4 T
he appliance has been used for hire purposes or non
d
omestic use.
5 T
he appliance is second hand.
6 M
orphy Richards reserves the right not to carry out any
t
ype of servicing under the guarantee at its discretion
7 Batteries and damage from leakage are not covered by
the guarantee.
This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. Morphy Richards products are intended for household use only. See usage limitations within the location safety instructions.
Morphy Richards has a policy of continuous improvement in product quality and design. The company, therefore reserves the right to change the specification of it’s models at any time.
For electrical products sold within the European Community. At the end of the electrical products useful life, it should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country
Exclusions
Registering your 2 year guarantee
Your 1 year guarantee
Disclaimer
IF YOU ARE HAVING A PROBLEM WITH ONE OF OUR PRODUCTS, CALL OUR HELPLINE:
UK: 0344 871 0944 EIRE: 1800 409 119 SPARES: 0344 873 0710
562000 Rev2.qxp_Layout 1 19/01/2015 09:25 Page 32
Loading...