Page 1
Steam Generator
R
N333200 MUK Rev1
* Register online for your 2 year guarantee. See back of this instruction book for details. (UK and Ireland customers only)
Please read and keep these instructions for future use
IMPORTANT: To reduce limescale problems which would not be covered by the
guarantee, we recommend the use of a mix of 50% tap water and 50% distilled,
deionised or demineralised water (available from most large supermarkets).
Never use battery topping up fluid or water containing any substances like
starch, sugar, fragrant additives or defrosted water from a refrigerator.
Remember to clean and descale your steam generator.
Failure to adhere to the above guidelines will invalidate your guarantee.
IF YOU HAVE ANY DIFFICULTY WITH THIS PRODUCT,
INSTEAD OF TAKING IT BACK TO THE RETAILER, TRY:
1. The instruction booklet 2. Refer to www.morphyrichards.com
3. Or call our helpline: UK: 0344 871 0944, EIRE: 1800 409 119 (For UK & Eire customers only)
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 1
Page 2
2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities, or lack of experience
or knowledge, if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
•
Keep the steam generator and its cord out of reach
of children less than 8 years of age at all times.
•
The steam generator must not be left unattended
while it is connected to the supply mains.
•
The steam generator must be used and rested on
a stable surface.
•
When placing the iron on the steam generator base
or on its heel, ensure that the surface on which the
heel or base is placed is stable.
•
The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
•
The filling aperture may be opened during use, due
to the design of the system.
•
Do not operate with a damaged steam/supply
cord or grommet, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 2
Page 3
3
Health and safety ............................................................................
Electrical requirements ..................................................................
Steam generator overview / Features ...........................................
Control panel overview ...................................................................
Temperature guide ..........................................................................
Location ...........................................................................................
Before use ........................................................................................
Using the Steam Generator ...........................................................
Features ...........................................................................................
Maintenance ....................................................................................
Emptying and storing .....................................................................
Contact us .......................................................................................
Troubleshooting ..............................................................................
Guarantee ........................................................................................
Contents
2
3
4
5
5
6
6
6, 7 & 8
8
9 &10
10
10
11
12
Personal safety
•
CAUTION - HOT:
Burns can occur from
t
ouching hot parts, hot
water or steam, or the
i
ron rest plate.
•
WARNING: Never direct steam at
electrical components or fittings.
I
f in doubt about the suitability of
steam for cleaning an appliance,
c
ontact the appliance
manufacturer for advice prior to
cleaning.
• WARNING: Never touch the plug
o
r cable with wet hands.
•
WARNING: Nozzles and tools will
be hot after use. Allow to cool
before attempting to remove.
• WARNING: Do not
discharge the
steam towards
people or
animals.
Danger of
scalding.
•
To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
• The plug should be removed from
the wall socket after use, before
cleaning, filling or changing the
accessories, or carrying out user
maintenance.
Location
• D
o not use or keep this product
outside.
• D
o not store the appliance near hot
surfaces eg. ovens or heating
appliances.
Mains cable
•
WARNING: A damaged or severed
mains cable fitted with a plug
should never be connected to the
m
ains supply. It must be
destroyed, as a damaged cable
b
ecomes hazardous if connected
to a power socket.
• Do not let the mains lead come into
c
ontact with the hot soleplate of the
iron.
• Do not allow the mains lead to
become strained.
Product safety
• WARNING: Always test on an
inconspicuous area first. Never
use on materials that can not
resist high temperature, such as
dralon, natural fur etc.
• WARNING: Misuse of the
appliance could cause personal
injury.
•
Never modify the appliance in any
way.
Other safety considerations
• Do not use any chemical
detergents, perfumes, alcohol or
descaler etc in water.
• Repairs to electrical appliances are
only to be undertaken by trained
p
ersonnel.
• U
nprofessional repairs can be
dangerous for users.
• U
se only genuine Morphy Richards
spare parts and accessories.
• The appliance must not be left
unattended while connected to the
s
upply mains.
• This appliance is intended for
d
omestic use only. Misuse or use
for commercial or any other
p
urpose will render the guarantee
invalid.
Electrical requirements
• Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
• If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
• WARNING: This appliance must
be earthed.
•
Should the fuse in the mains plug
require changing, a 13 amp BS1362
fuse must be fitted.
STEAM
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 3
Page 4
4
(1) Filling aperture
(2) Water tank release button
(3) Detachable water tank
(4) Steam trigger
(5) Temperature indicator light
(6) Soleplate
(7) Iron handle
(8) Temperature dial
(9) Iron-to-base lock
(10) Cable support
(11) Iron
(12) Iron locking hook
(13) Iron rest plate
(14) Base unit
(15) Rear docking slot
(16) Power cord storage
(17) Steam level indicator lights
(18) Steam level select button
(19) Descale button
(20) On/Off power button
(21) Power cord
(22) Steam supply cord
(23) Steam supply cord
storage
(24) Boiler tube attachment
(25) Boiler tube storage
points
(26) Boiler tube
(27) Boiler tube crevice
(28) Boiler screw
Steam generator overview
282726
24
25
3
2
10
8
6
7
13
21
22
23
11
14
1
4
5
1
2
15
9
16
17
18
19
20
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 4
Page 5
5
Control panel overview
Steam level indicator lights (17)
Press the steam level select button (18) to adjust
the steam level. The steam level selected will be
displayed by illumination of the relevant steam
level indicator light: low
(17a), medium (17b) or
high
(17c). See step 5 of ‘Using the Steam
Generator’ on page 7.
On/Off power button (20)
Connect to a mains outlet and press the On/Off
power button
(20). The button will illuminate and
the low steam level indicator light
(17a) will flash.
To turn off, press and hold the On/Off power
button for 3 seconds.
Steam level select button (18)
Press the steam level select button (18) to toggle
through the steam levels. Each press cycles the
level from low to medium to high, back to low and
so forth.
Descale button (19)
When the system requires cleaning, the descale
button
(19) will illuminate. When this happens,
follow the instructions under ‘Self Clean’ on page
9.
On/Off power
button
20
Low steam level
indicator light
1
7a
Medium steam
level indicator light
1
7b
High steam level
indicator light
17c
Descale
button
19
Steam level
selector button
18
Heat setting markings on the temperature dial of all Morphy Richards irons match those of the International
Textile Care Labelling Code
Temperature guide
Symbol
(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
Control dial
positions
Do not iron
• •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen
Rayon, Rayon
mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(see step 5 of
‘Using the Steam
Generator’ on
page 7)
No steam
(see ‘Dry ironing’
on page 8)
Low Medium / High High
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 5
Page 6
6
Using the Steam Generator
Plug the appliance into a mains outlet, you will
hear a beep. Press the On/Off button
(20), it will
beep again and the On/Off button and the
temperature indicator light
(5) will illuminate and
the low steam level indicator light
(17a) will flash.
2
Remove the detachable water tank (3) by
squeezing the water tank release button
(2), and
fill with water through the filling aperture
(1) to the
max fill line
. Replace the water tank.
IN HARD WATER AREAS, WE RECOMMEND A
MIX OF 50% TAP WATER AND 50% DISTILLED,
DEIONISED OR DEMINERALISED WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
NOTE: Please see point 2 of ‘Exclusions’ on page 12.
Re-filling during use
If the water level is too low, the unit will not
produce steam. If this happens, refill the
detachable water tank
(3) with water.
1
L
ocate the steam generator horizontally on the iron
r
est plate of your ironing board (if large enough) or
on a heat resistant stand at the same height as
your ironing board or below it. Always ensure the
s
team generator is on a firm surface when ironing.
WARNING: Do not use the product on a surface
which could be damaged by heat or steam such
a
s a worktop or a polished wood surface.
I
f in doubt, contact Morphy Richards.
R
emove any protective cover from the soleplate
(6)a
nd the base unit (14)
.
Unwind and straighten the power cord
(21) and
steam supply cord
(22).
W
e recommend for first time ironing that you
iron over an old towel.
Lo
c
a
t
i
o
n
Be
f
o
re
use
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 6
Page 7
7
Turn the temperature dial (8) to suit the garment
(see ‘Temperature guide’ on page 5). The
temperature indicator light
(5) illuminates until the
temperature is reached. Begin ironing when the
temperature indicator light goes out.
It is advised to begin with ‘cool’ fabrics (see
above) and work up to higher settings. An iron
heats up quicker than it cools down so you’ll save
time and electricity.
If you turn the temperature dial
(8) down from a
hot setting to a cooler setting, wait until the
temperature indicator light
(5) goes out (indicating
the correct temperature has been reached) before
you continue ironing.
3
U
n
l
o
c
k
t
h
e
i
r
o
n
(
1
1
)
f
r
o
m
i
t
s
s
t
o
r
a
g
e
p
o
s
i
t
i
o
n
o
n
t
o
p
o
f
t
h
e
b
a
s
e
u
n
i
t
(
1
4
)
b
y
s
l
i
d
i
n
g
t
h
e
i
r
o
n
-
t
o
-
b
a
s
e
l
o
c
k
(
9
)
t
o
t
h
e
p
o
s
i
t
i
o
n
m
a
r
k
e
d
w
i
t
h
a
n
u
n
l
o
c
k
e
d
p
a
d
l
o
c
k
i
c
o
n
-
t
h
e
i
r
o
n
c
a
n
t
h
e
n
b
e
l
i
f
t
e
d
o
f
f
t
h
e
b
a
s
e
u
n
i
t
.
W
A
R
N
I
N
G
:
T
h
e
s
o
l
e
p
l
a
t
e
w
i
l
l
b
e
h
o
t
.
D
u
r
i
n
g
u
s
e
,
t
h
e
i
r
o
n
(
1
1
)
m
a
y
b
e
r
e
s
t
e
d
o
n
t
h
e
i
r
o
n
r
e
s
t
p
l
a
t
e
(
1
3
)
.
4
Using the Steam Generator (continued)
5
4
Ironing with steam
Press the steam level select button (18) to select
your desired steam level. The selected steam level
will be displayed by illumination of the relevant
steam level indicator light
(17). The steam level
indicator light will stop flashing and illuminate
constantly when the selected steam level is reached.
To operate the steam, press and hold the steam
trigger
(4) to release steam. There will be a slight
delay whilst the steam is drawn from the base and
along the steam cord to the irons soleplate
(6).
NOTE: Residual steam - as the steam has a long
distance to travel along the steam cord it is likely
that there will still be some steam coming from the
soleplate for a short while after you have released
the trigger. This is normal and will eventually stop
after several seconds. If it doesn't you may have
accidentally activated the steam boost in which case
press the steam trigger again to switch off the steam
boost.
WARNING: The steam supply cord
(22)
will get hot
during use.
4
6
Steam boost
The steam boost function is ideal for relaxing the
fibres of tougher fabrics (like jeans and linen) and
getting rid of those stubborn, hard to reach
creases.
To produce a powerful shot of steam during
ironing, simply press the steam trigger
(4) twice
in quick succession. To turn this off, press the
steam trigger again.
To conserve water in the tank, we recommend
you switch off the steam boost when the iron is
not in use.
NOTE: The product may occasionally produce a
pumping sound during steam ironing. This is
normal and is caused by water being pumped
from the water tank to the steam generator. If
the pumping sound suddenly becomes louder
or the steam diminishes, check and refill the
water tank if it has become empty.
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 7
Page 8
8
Dry ironing
To use your steam generator as a dry iron only,
follow steps 2, 3 and 4 of ‘Using the Steam
Generator’ on page 6. You do not need to put
water in the tank or select a steam level. Press
the steam trigger
(4) at least once every 10
minutes, or the product will automatically turn
off.
Auto shut-off
If
the iron
(11) is not used for 10 minutes, the
product will automatically turn off for safety and
to save energy, and a beep will be heard.
To restart, press the On/Off power button (20)
(see step 2 of ‘Using the Steam Generator’ on
page 6) and wait for the temperature to rise
again.
Steam function
During steaming, small amounts of water may be
ejected from the soleplate
(6)
. This is normal and
can be avoided by using the steam for short
amou
nts of time and only when the iron is at the
correct temperature (the temperature indicator
light (5) on the iron (11) goes out when ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit during ironing.
Vertical steam
Vertical steam is useful for removing creases
from hanging clothes, curtains, upholstery, etc.
Hold the iron
(11)
between 1cm and 2cm away
from the item and press the steam trigger
(4)
twice in quick succession for a longer boost of
steam. To turn the steam boost off, press the
steam trigger again.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Features
4
W
hen you have finished ironing, turn off the
appliance by pressing and holding the On/Off
p
ower button
(
20)for three seconds. A beep will be
heard and the On/Off power button and steam level
indicator light
(17) will be extinguished.
Disconnect the plug from the mains outlet.
Using the Steam Generator (continued)
7
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 8
Page 9
9
Self clean
When the boiler requires descaling, the descale
b
utton
(
19)will illuminate. When this happens, the
boiler must be descaled. The button’s light will go
o
ut only after the scale has been removed.
1
Unplug the appliance from the mains outlet and
l
eave to cool for two hours.
2
Lock the iron (11) in place on the base unit (14).
S
ee ‘Storing the steam iron’ on page 10.
3
Remove the detachable water tank (3) to prevent
water spillage and upturn the steam generator.
This reveals the boiler screw (28) on the
underside of the base unit.
4
Remove the boiler screw by unscrewing it
anti-clockwise.
WARNING: Never remove the boiler screw
when the steam generator is hot.
5
Remove the boiler tube (26) and the attached
boiler tube attachment (24) from their storage
position.
6
Push the boiler tube attachment (24) firmly into
the hole where the boiler screw was removed
from. Ensure the boiler tube (26) is sitting within
the boiler tube crevice (27).
7
Turn the steam generator back over so the iron
(11) is uppermost.
8
Fill the detachable water tank and replace it back
into the base unit (14).
Never pour any descaling solution or any other
chemicals into the water tank. This will
damage the product. Only use clean water.
9
Place the front end of the steam generator
securely over a sink so the boiler tube
(26) drops
down into the sink. Ensure the boiler tube is not
squashed between the steam generator and the
edge of the sink.
10
Plug the appliance back in at the mains and turn
the power on.
11
Press and hold the descale button (19) and the
steam trigger (4) at the same time for one
second. A beep will be heard and the descale
button will begin to flash. The steam generator
will commence self-cleaning and scale and water
will begin to flow through the boiler tube into the
sink. The process will take around two minutes to
complete. When finished, three beeps will be
heard, the descale button’s light will extinguish
and the appliance will shut off automatically.
Maintenance
28
24
2
6
2
7
26
24
26
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 9
Page 10
10
12
U
nplug the appliance from the mains.
13
Once cooled, remove the boiler tube attachment
a
nd boiler tube and replace them back into their
s
torage position.
14
R
eplace the boiler screw and screw it into
p
osition in a clockwise direction. Ensure the
boiler screw is tightened fully.
1
5
T
he descale button’s light will extinguish the next
time you use the product. Please wait for up to
o
ne minute whilst it pumps water and registers
that the boiler has been cleaned.
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate (6),
set the iron at the MAX position and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
Allow the appliance to cool.
Remove the detachable water tank
(3) by
squeezing the water tank release button (2).
Empty the water tank. Once the water tank is
empty, re-attach it to the base unit (14).
Wrap the power cord (21) and steam supply cord
(22) loosely in long loops. Gently push the looped
steam supply cord and power cord into the steam
supply cord storage
(23)
and power cord storage
(16)
respectively. Avoid kinking of cables,
particularly where they meet
the base unit.
WARNING: Do not pull too tightly on the steam
supply cord or on the cable support
(10) when
looping the power cord (21) and steam supply
cord (22). Damage to cables caused by
wrapping too tightly will not be covered by the
guarantee.
Storing the steam iron
L
ock the iron (11)into the storage position on top
of the base unit
(14) by sliding the tip of the
s
oleplate(6)under the iron locking hook(12)
.
With the lower end of the soleplate in position
adjacent to the lower end of the iron rest plate
(
13), slide the iron-to-base lock(9)to the position
marked with a padlock icon - this secures the
s
oleplate in place. Once the iron-to-base lock is
l
ocked securely, the iron can be carried by the
iron handle (7).
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from. Please have the product name, model
number and serial number to hand when you call
to help us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk To Us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact us
Em
p
ty
ing
and
sto
ring
4
23
16
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 10
Page 11
11
Troubleshooting
• N
o power or not heating up.
• Overheating or not getting hot enough.
• Not steaming or poor steam.
• Dripping from the holes in the soleplate.
• Tripping Electrics.
Problem Solution
• Steams continuously.
• The self clean is not working.
1.C
heck the fuse and the fuse rating (should be 13amp).
2.T
ry a different appliance in the socket as it may be the
s
ocket that is at fault.
3.C
heck that the auto shut off has not operated.
4. Check the temperature dial has not been set to MIN.
1. Adjust the temperature dial to ensure the setting matches
that recommended on the garment or refer to the
“temperature guide” section.
2. Allow the iron to reach temperature and stabilise for 1-2
minutes if it has just been plugged in, or has just been
woken up from auto shut off.
1. There will be a short delay with a steam generator whilst the
steam travels from the base to the iron.
2. Check that there is enough water in the tank.
3. If the iron’s auto shut off feature has activated, wake up the
iron and allow it to reach temperature before using steam.
4. If the descale button is illuminated, perform a self-clean to
clear away limescale inside the iron (refer to “Self Clean”
section).
1. Ensure the temperature is set within the steam band (refer
to the “temperature guide” section). The iron will not be hot
enough to produce steam if the temperature is set too low.
2. The steam level should be set lower if the temperature is set
lower (refer to the “temperature guide” section) to prevent it
from dripping.
3. If the iron’s auto shut off feature has activated, wake up the
iron and allow it to reach temperature before using steam.
1. Try using a different socket.
2. Ensure there are no other appliances being used on the
same set of sockets as the iron.
1. It is normal for some residual steam to continue through the
soleplate for a short while after releasing the steam trigger.
2. The steam boost feature may have been activated by
pressing the steam trigger twice in quick succession. This
can be turned off by pressing the steam trigger again.
1. In order to perform a self clean, the descale button has to
be illuminated.
2. The unit must have cooled down enough. Please leave the
unit to cool down for longer and try again.
3. Ensure the water tank has enough water in it.
4. Ensure you are pressing and holding both the descale
button and the steam trigger at the same time until a beep
is heard.
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 11
Page 12
RN333200 MUK Rev1 04/18
Y
our standa rd 1 year guarantee is extended for an
additional 12 months when you register the product within
28 days of purchase with Morphy Richards. If you do not
r
egister the product with Morphy Richards within 28 days,
y
our product is guaranteed for 1 year. To validate your 2
y
ear guarantee register with us online at
www.morphyrichards.co.uk/support
Or call our customer registration line, quoting model and
s
erial number, these numbers can be found on the base of
the product
UK 0344 871 0242
I
RE 1800 409 119
N
.B. Each qualifying product needs to be registered with
M
orphy Richards individually.
Please note that the 2 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
for more information.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no.
Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting Model number and Serial number on the product,
or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions),
the faulty appliance will then be repaired or replaced as
appropriate and dispatched usually within 7 working days
of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item will be calculate d from original purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
For example, water should be emptied after each use.
M
orphy Richards shall not be liable to replace or repair the
g
oods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, misus e, negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
b
een caused by power surges or damage caused in transit.
2 The fault has been caused by using water other than that
recommended by Morphy Richards.
3 T
he fault is caused by limescale build-up.
4 The cables are damaged due to wrapping too tightly or
excessive kinking.
5 The appliance has been used on a voltage supply other
than that stamped on the products.
6 R
epairs have been attempted by persons other than our
service staff (or authorised dealer).
7 The appliance has been used for hire purposes or non
domestic use.
8 The appliance is second hand.
9 Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
• This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserve s the right to change the specification of
its models at any time.
For electrical products sold within the
Europea n Com munity. At the end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Loc al Authority or retai ler for
recycling advice in your country
Exclusions
Registering your 2 year
guarantee
Your 1 year guarantee
Disclaimer
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8AJ
IF YOU ARE HAVING A PROBLEM
WITH ONE OF OUR PRODUCTS,
CALL OUR HELPLINE:
UK: 0344 871 0944
EIRE: 1800 409 119
SPARES: 0344 873 0710
RN333200 MUK Rev1.qxp_IB 11/04/2018 17:16 Page 12
Loading...