Heated Bedding
Please read and keep these instructions
getting the best from your
new heated bedding...
Safety
• For your safety, the in-built system in this product will
automatically shut off the power if it reaches a
temperature that is higher than considered comfortable.
It will also shut off automatically if any unsafe situation
should arise.
Washing instructions
• Check if the blanket is suitable for machine washing by
checking the label attached to the blanket.
www.morphyrichards.co.uk
1
S1 Rev 2 21/7/04 1:43 PM Page 1
0870 060 2616
1800 409089
2
Important safety
instructions
The use of any electrical appliance
requires the following of basic common
sense safety rules.
Primarily there is danger of injury or death
and secondly the danger of damage to the
appliance. These are indicated in the text by
the following two conventions:
WARNING: Danger to the person!
IMPORTANT: Damage to the appliance!
In addition we offer the following
essential safety advice.
Care instructions
• Examine frequently for any signs of wear
or damage to the blanket, switch or cord.
In case of damage or misuse, please
return immediately following instructions
under servicing.
• During the summer, the blanket can be
used to air the mattress. To store, roll in a
towel and store in a dry place. Avoid
folding or creasing the blanket once
unpacked.
• Do not dry clean the blanket, follow
washing instructions on the label attached
to the blanket and the details that relate
to your blanket.
Personal safety
• Do not use with a helpless person, an
infant or a person insensitive to heat.
•Young children should be instructed on
how to operate the controls safely and
heat settings controlled by a parent or
guardian.
• Do not use a hot water bottle at the same
time as using the blanket.
Product safety
• Ensure the blanket is used in the manner
in which it is intended, either as an
overblanket or underblanket as
appropriate.
• If used on an adjustable bed, check the
blanket or cord cannot become trapped
or rucked.
• Ensure the product is correctly fitted to
the bed, following the instructions in this
booklet.
• Do not insert pins or any sharp objects
into the blanket.
• Do not tuck the heated part of material
under the mattress.
• Do not use if the blanket is wet.
•Avoid pressing creases or folds into the
blanket. Do not switch on if the blanket is
folded, creased or rucked.
• Do not use any lead, switch or cord other
than the one supplied with this blanket.
• Do not coil or lay the lead on the blanket.
• Not intended for medical use in hospitals.
All Morphy Richards heated blankets have been manufactured to the highest European
standards. This product has been comprehensively tested for all known safety situations, so
you can relax in the knowledge that it will provide warmth, comfort and peace of mind.
IMPORTANT INSTRUCTIONS
PLEASE READ CAREFULLY
AND RETAIN FOR
FUTURE USE
S1 Rev 2 21/7/04 1:43 PM Page 2
3
Electrical requirements
Check that the voltage on the rating
label of your appliance corresponds with
your house electricity supply which must be
A.C. (Alternating Current).
If the socket outlets in your home are not
suitable for the plug supplied with this
appliance, the plug should be removed and
the appropriate one fitted.
WARNING: The plug removed from
the mains lead, if severed, must be
destroyed as a plug with bared flexible
cord is hazardous if engaged into a live
socket outlet.
Should the fuse in the 13 amp plug
require changing, a 3 amp BS1362 fuse
must be fitted.
This appliance does not need to be
earthed. It is a double insulated product.
Before use
Before using this appliance ensure that
the voltage indicated on the product
corresponds with the mains voltage in your
home. If you are in any doubt about your
supply, ask your electrical dealer or local
electricity company.
WARNING: Do not attempt to use
the blanket with controls other than
those supplied with the unit as
referred to on the rating label attached
to the blanket.
Dual control models
Each side of the blanket has a
completely separate element and each is
supplied with its own independant mains
lead. A 13amp plug on each lead is
essential.
Do not connect both flexible cords to
one 13amp plug.
The two leads should preferably be
plugged into individual sockets. However, if
only one socket is accessible, then a dual
adaptor should be used.
WARNING: Only the electric blanket
should be connected to the dual
adaptor. If you are unsure, please
contact a qualified engineer.
It is quite normal for the switch to
become warm as the components encased
are part of the protection circuit.
Safeguard overheat
protection system
Activation
The system will remain dormant
indefinitely as long as the blanket is
operating in the normal temperature range.
If for any reason the blanket is operated in
an abnormal situation or condition which
would otherwise have induced a rapid
temperature rise high enough to constitute a
hazard, the OVERHEAT SYSTEM should
intervene by cutting off the supply current
before the temperature reaches the point at
which damage may occur.
It is normal for the lead from the blanket
to the switch to become warm as this is
part of the heater protection circuit
extended to the switch.
Action in case of activation
In the event of the OVERHEAT SYSTEM
operating, the blanket will cease to function
and must be returned to the service
department address given in this leaflet.
WARNING: No attempt should be
made to repair the blanket or have it
repaired locally and the switch
supplied must never be replaced other
than by the manufacturers since the
specialised components are not
generally available.
A charge will be made for this service
but remember that the alternative would
have been a damaged blanket and bedding.
The fact that this blanket incorporates
the overheat system does not absolve the
user from observing these instructions.
S1 Rev 2 21/7/04 1:43 PM Page 3
Underblanket with tie
tapes
• Use only as an underblanket and do not
use above the occupant of the bed.
• The blanket must be secured to the
mattress in the following manner. Place
the blanket directly on the mattress and
ensure that a space of 10-15cm (4-6
inches) is left between the bottom edge
of the blanket and mattress.
•WARNING: Ensure the blanket is not
folded, rucked or creased. When in
use do not cover with pillows.
Fitting instructions
1 At the starting position the tape must be
passed under the corner of the mattress,
threaded up through the centre eyelet,
passed under the adjacent corner,
threaded through both eyelets on the
long side of the blanket, passed under
bottom corner, threaded through centre
eyelet, passed under the remaining
corner and finally tied securely to the
corner eyelet at the finish position (see
diagram A).
• If the blanket is stretched too tightly, not
allowing for ‘give’ of mattress when the
bed is occupied, distortion of the edges
may take place.
Underblanket without
tie tapes
• Use only as an underblanket and do not
use above the occupant of the bed.
•WARNING: Ensure the blanket is not
folded, rucked or creased. When in
use do not cover with pillows.
Fitting instructions
1 Place the blanket directly on the
mattress, with the control switch end at
the head of the bed.
• The blanket must be secured to the
mattress in the following manner. Place
the blanket directly on the mattress and
ensure that a space of 10-15cm (4-6
inches) is left between the bottom edge
of the blanket and mattress (see diagram
B).
4
A
B
S1 Rev 2 21/7/04 1:43 PM Page 4
10-15 cm
4-6 inches
10-15 cm
4-6 inches
5
Mattress covers with
elasticated corner tapes
1 Place the mattress cover directly on the
mattress with the control switch end at
the head of the bed.
2 Tu rn the elastic corners underneath the
mattress to secure in place (see diagram
C).
• Ensure all creases are smoothed out.
Mattress protectors with
elasticated skirt
1 Place the mattress cover directly on the
mattress with the control switch end at
the head of the bed.
2 Fit the shaped corners to the mattress
and turn the elasticated edges of the
skirt under the mattress (see diagram
D).
• Ensure all creases are smoothed out and
the skirt fits tightly round the sides of the
mattress.
C D
S1 Rev 2 21/7/04 1:43 PM Page 5
6
Switch control
How to use
1 Ensure the blanket is fitted to the bed
correctly.
2 Plug the power lead into the closest
socket, using an extension lead if
needed to ensure that the lead is not
stretched.
Preheating the bed
1 Move the heat setting on the control
switch to heat level 2 or 3, depending on
the level of the heat required. Allow
approximately 60-90 minutes for the
blanket to heat the bed thoroughly,
although this time may vary depending
on the room temperature and type of
bedding used.
All night use
1 Move the heat setting on the control
switch to heat level 1.
• This setting will provide safe and
comfortable heat to sleep on all night.
• This setting can be used to air the bed.
WARNING: Always ensure that the
heat setting is moved to the OFF
position when you get up the next day,
or after airing the bed.
Braille markings
• Braille markings are located on the back
of the switch to help identify the
direction of the heat level in the dark, or
if visually impaired.
• The highest heat level
pre-heat is identified by 3 raised nodules
mid level by 2 raised nodules
low level (all night) by 1 raised nodule
Features
⁄ Illuminated heat setting light
(To identify heat levels in the dark)
¤ Heat levels 2 & 3
(Used to pre-heat)
‹ Heat level 1
(Safe & comfortable to sleep all night)
› Braille markings
(located on the back of the switch)
fi Off position
¤
›
⁄
‹
fi
S1 Rev 2 21/7/04 1:43 PM Page 6
7
Washing instructions
WARNING: Check if the blanket is
suitable for machine washing by
checking the label attached to the
blanket.
• Do NOT dry clean -
• Do NOT iron -
WARNING: Before washing ensure
that you detach all the controls from
the blanket.
• Only use in a washing machine with a
drum large enough to take the blanket
without forcing it in.
• Measure the blanket so it can be
stretched back to its original size whilst
wet.
Machine washing
1 Unplug the blanket from the power
socket.
2 Disconnect the control switch and cord
from the blanket by lifting the locking
lever over the raised button and pull
apart. E
3 Wash on the WOOL setting at 40˚C.
4 Gently stretch the blanket back to it’s
original shape and size before line drying
WITHOUT using clothes pegs on the
wired area of the blanket. (See
instructions for tumble drying below).
Hand washing
1 Unplug the blanket from the power
socket.
2 Disconnect the control switch and cord
from the blanket by lifting the locking
lever over the raised button and pull
apart. E
3 Use a mild washing liquid or detergent
and lukewarm water.
4 Immerse the blanket in the water and
allow to soak for 5-10 minutes.
5 Squeeze the soapy water through the
fabric.
6 Rinse the blanket thoroughly in cool
water, gently squeezing the fabric.
WARNING: Do not wring dry.
7 Gently stretch the blanket back to its
original shape and size before line drying
WITHOUT using clothes pegs on the
wired area of the blanket.
Sponge washing
1 Unplug the blanket from the power
socket.
2 Use a mild washing liquid or detergent
and lukewarm water.
3 Sponge wash dirty areas of the blanket
avoiding the control switch area.
4 Gently stretch the blanket back to its
original shape and size before line drying
WITHOUT using clothes pegs on the
wired area of the blanket.
Tumble drying
WARNING: Only blankets with
detachable controls can be tumble
dried.
1 Control must be removed.
2 Gently stretch the blanket back to its
original shape before drying.
3 Tumble dry on the low heat setting,
following the manufacturers instructions
for the required drying time.
E
S1 Rev 2 21/7/04 1:43 PM Page 7
40º
8
Servicing
Examine the blanket and cord frequently
for signs of wear or damage. In the case of
damage, or for routine inspection every 2
years, return the blanket to the service
department (see address below).
A standard service charge (inclusive of
packing and return carriage) is made for
routine inspection where no repair is found
to be necessary.
If the blanket fails to operate, check the
following before returning:
1 Ensure that the plug and socket have not
become disconnected.
2 Check that the supply plug is correctly
connected to the flex.
3 Check the supply fuse and the 3 amp
plug fuse if applicable.
Service department
Waterside Mill
Langham Street
Rosegrove
Burnley
BB12 6AL
Republic of Ireland c/o
Dimpco Ltd
Airport Road
Cloghran
Co. Dublin
S1 Rev 2 21/7/04 1:43 PM Page 8
Helpline
Should you need any advice on using
the product, please contact our helpline,
8:30 - 5:00 Mon - Thurs
8:30 - 4:00 Fri
Tel: 0870 060 2616
9
S1 Rev 2 21/7/04 1:43 PM Page 9
0870 060 2616
1800 409089
I1000M UK Rev 2 0604
Service and Aftersales Department,
Waterside Mill, Langham Street,
Rosegrove, Burnley, BB12 6AL
Helpline (office hours)
UK 0870 060 2616
Republic of Ireland 1800 409089
Morphy Richards products are intended for
household use only
Morphy Richards has a policy of continuous
improvement in product quality and design.
The Company, therefore, reserves the right
to change the specification of its models at
any time.
Your three year
guarantee
It is important to retain the retailers
receipt as proof of purchase. Staple your
receipt to this back cover for future
reference.
Please quote the following information if
the product develops a fault. These numbers
can be found on the rating label attached to
the blanket.
Model no. Serial no.
All Morphy Richards products are
individually tested before leaving the factory.
In the unlikely event of any appliance proving
to be faulty within 28 days of purchase it
should be returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days and
within 36 months of original purchase, you
should contact the Helpline number quoting
Model number and Serial number on the
product, or write to Morphy Richards at the
address shown.
You will be asked to return the product (in
secure, adequate packaging) to the address
below along with a copy of proof of
purchase.
Subject to the exclusions set out below
(see Exclusions) the faulty appliance will then
be repaired or replaced and dispatched
usually within 28 working days of receipt.
If for any reason this item is replaced
during the 3 year guarantee period, the
guarantee on the new item will be calculated
from original purchase date. Therefore it is
vital to retain your original till receipt or
invoice to indicate the date of initial
purchase.
To qualify for the 3 year guarantee the
appliance must have been used according to
the manufacturers instructions.
EXCLUSIONS
Morphy Richards shall not be liable to
replace or repair the goods under the terms
of the guarantee where:
1 The fault has been caused or is
attributable to accidental use, misuse,
negligent use or used contrary to the
manufacturers recommendations or where
the fault has been caused by power
surges or damage caused in transit.
2 The appliance has been used on a voltage
supply other than that stamped on the
products.
3 Repairs have been attempted by persons
other than our service staff (or authorised
dealer).
4 Where the appliance has been used for
hire purposes or non domestic use.
5 Morphy Richards are not liable to carry
out any type of servicing work, under the
guarantee.
This guarantee does not confer any rights
other than those expressly set out above and
does not cover any claims for consequential
loss or damage. This guarantee is offered as
an additional benefit and does not affect your
statutory rights as a consumer.
• This guarantee is valid in the UK and
Ireland only.
S1 Rev 2 21/7/04 1:43 PM Page 10
Loading...