www.morphyric
hards.com
PerformAir Cyclonic vacuum cleaner
Please read and keep these instructions
GGeettttiinngg tthhee bbeesstt ffrroomm yyoouurr nneeww cclleeaanneerr......
If your cleaner is not picking up as well as it should, please check
FFiilltteerrss
It is important to rotate the filter dial prior to emptying.
This action shakes clean the dust canister filter. See page 6.
BBlloocckkaaggeess
Check the nozzle, tubes and hose for blockages.
AAlllleerrggyy ssuuffffeerreerrss
See page 7 for allergy details.
TTuurrbboo nnoozzzzllee
((cceerrttaaiinn mmooddeellss oonnllyy))
Remove hair and dirt caught around the brush bar regularly.
SSaaffeettyy ccuutt oouutt
If the product switches itself off during use refer to page 7 for instructions.
VC71060 MUK Rev 5 05/06
For replacement parts, help with using your Morphy Richards, problems
and lots more, contact us by phone or through our website.
UUKK HHeellpplliinnee:: 00887700 006600 22660044
RReeppllaacceemmeenntt ppaarrttss:: 00887700 116677 66663355
IIrreellaanndd 11880000 440099111199
71060 Rev5 17/5/06 12:52 Page 1
2
IMPORTANT
SAFETY
INSTRUCTIONS
The use of any electrical
appliance requires the following
common sense safety rules.
Primarily there is danger of
injury or death and secondly
the danger of damage to the
appliance.
Please read before using the
appliance
Location
• Do not use or keep this
product outside in the rain.
• Do not store the appliance near
hot surfaces eg ovens or
heating appliances.
Mains lead
• Do not allow the mains lead to
become strained or run this
appliance over it.
• If the electrical cable becomes
damaged the cable assembly
must be replaced. Do not
attempt this task yourself,
contact the helpline number
that is found at the bottom of
the page.
Personal safety
• The plug must be removed
from the wall socket before
cleaning or maintaining the
appliance.
• Never modify the cleaner in any
way.
• Never use in the presence of
explosive liquids or vapours.
• Never pick up inflammable or
poisonous liquids such as
petrol, copier toner or other
volatile substances. Never pick
up acids, asbestos or asbestos
dust.
• Repairs to electrical appliances
are only to be undertaken by
trained personnel.
Unprofessional repairs can be
dangerous for users.
• Use only genuine Morphy
Richards spare parts and
accessories.
• The appliance must never be
left running when
unsupervised.
• This vacuum cleaner is
intended for domestic use only.
Misuse or use for commercial
or any other purpose will
render the guarantee invalid.
Product safety
• Never use the appliance
without the filters being
installed.
• Never use the appliance to
vacuum hot ashes, broken
glass, sharp objects or liquids.
Children
• Children do not understand the
dangers associated with
operating electrical appliances.
Never allow children to use this
appliance.
ELECTRICAL
REQUIREMENTS
Check that the voltage on the
rating plate of your appliance
corresponds with your house
electricity supply which must
be A.C. (Alternating current).
If the socket outlets in your
home are not suitable for the
plug supplied with this
appliance the plug should be
removed and the appropriate
one fitted.
If you cut off the plug and let
go of the cable it will rewind
into the machine therefore you
must pull out a length of cable
and secure it before cutting the
plug off and re-fitting a new
one.
WARNING: The plug
removed from the mains
lead, if severed, must be
destroyed as a plug with a
bared flexible cord is
hazardous if engaged into a
live socket outlet.
Should the fuse in the 13 amp
plug require changing a 13
amp BS1362 fuse must be
fitted.
UK Helpline 0870 060 2604 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119
71060 Rev5 17/5/06 12:52 Page 2
FEATURES
⁄ Hose inlet
¤ Dust canister
‹ Dust canister release button
› Carrying handle
fi On/off power switch
fl Variable power switch
‡ Parking slot
· Tool storage drawer
‚ Plug recess
„ Cable rewind switch
‰ Exhaust filter grille
 Exhaust filter
Ê Dust canister lid
Á Pleated, washable dust canister
filter
Ë Mesh filter cover
È Standard hose
Í Hose handle with airflow
regulator
Î Telescopic tube (length
adjustable)
Ï Combination floor nozzle
Ì Hard floor nozzle (certain
models only)
Ó Large turbo nozzle (certain
models only)
Ô Small turbo nozzle (certain
models only)
Upholstery nozzle
Ò Clip on brush (attached to )
Ú Crevice tool
Note: ,Ò,Ú are stored in
the tool storage drawer ·.
Û Stretch stair hose
Ù Filter cleaning brush
3www.morphyrichards.com
⁄
¤
‹
›
fi
fl
‡
‚
Ê
‰
¤
„
Â
Ë
È
·
Í
Î
Ï
Ì
Ô
Ó
Á
Ò
Ú
Û
Ù
71060 Rev5 17/5/06 12:52 Page 3
4 UK Helpline 0870 060 2604 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119
OPERATING THE
APPLIANCE
Quick start
1 Assemble the nozzle, telescopic tube
and hose as shown. (Shown on page
3)
2 Pull out the mains cable to it’s full
length and plug into the mains
supply.
3 Switch on by pressing the on/off
switch
fi.
TOOLS AND
ACCESSORIES
1 Fit the hose to the cleaner by
inserting the hose end into the hose
inlet
⁄. When removing, squeeze
the clips either side and pull.
2 Attach the hose. Extend to the
required length by pushing up the
slider release and pulling out the
tube
A.
The hose handle features an airflow
regulator which allows suction to be
reduced as required.
3 Attach your choice of floor nozzle to
the tube.
Î
Combination floor
nozzle
The combination floor nozzle can be
adjusted to suit different floor
surfaces. Retract the brushes for use
on carpet. The brushes should be
down for use on hardfloors or
damage may occur.
Hand tools
The crevice tool Ú (for awkward
places, behind radiators etc) and the
upholstery nozzle with clip on
brush Ò (for curtains and
upholstery) are stored in the tool
drawer ·. The crevice tool is used
for hard surfaces, pelmet, delicate
objects etc B.
Using the large turbo
nozzle
(certain models only)
Attach the large turbo nozzle to the
telescopic tubes.
This nozzle is ideal for carpet and
especially effective at removing pet
hair.
Using the small turbo
nozzle
(certain models only)
Attach the turbo nozzle to the hose
handle Í for use on upholstery and
stairs.
WARNING: The turbo nozzle
should not be used with the
extension tubes. Attach to
the hose handle only.
Cleaning the turbo
nozzles
The turbo nozzles should be
regularly cleaned and any hairs or
fibres wrapped around the brush bar
removed to maintain optimum
performance. To aid cleaning, the
small turbo nozzle can be opened up
by pushing the button on the nozzle
forwards. A cover on the bottom of
the large turbo nozzle allows access
to the turbine fan.
Hardfloor nozzle
(certain models only)
Attach the hardfloor nozzle to the
telescopic tubes. This nozzle is ideal
for use on wood, laminate, tile and
vinyl flooring.
Stretch stair hose
An additional stretch hose is also
provided for use on stairs. Fit the
hose to the cleaner by inserting the
hose end into the hose inlet. When
removing squeeze the clips either
side and pull.
WARNING: For safety, always
leave the cleaner at the bottom
of the stairs and clean upwards.
WARNING: We do not
recommend using the stair hose
for general floor cleaning.
B
A
Ú
Ò
71060 Rev5 17/5/06 12:52 Page 4
5www.morphyrichards.com
Quick guide to
accessories:
Combination
floor nozzle
With brushes
retracted
With brushes
retracted
With brushes
down
With brushes
down
Large turbo
nozzle
Small turbo
nozzle
Hard floor
nozzle
Crevice tool
Upholstery
nozzle with
clip on-brush
Carpet
Rugs
Wood/
laminate
Tile
Vinyl
Upholstery
Stairs
Small spaces
CONTROLS
Power
1 Assemble the nozzle, telescopic tube
and hose as shown. (Shown on page
3)
2 Pull out the mains cable to it’s full
length and plug into the mains
supply.
3 Switch on by pressing the on/off
switch fi.
Variable power
A Variable power switch fl varies
the suction power as required. For
example, maximum suction can be
used for cleaning carpets, hard floors
etc. and reduced suction for cleaning
upholstery and curtains.
Suction can also be controlled using
the airflow regulator on the hose
handle. Closed for maximum suction,
open for reduced suction.
Automatic cable
rewind
After use, unplug and press the
cable rewind switch to retract the
cable.
WARNING: When using the
cable rewind, always hold the
plug as the cable will rewind
quickly.
71060 Rev5 17/5/06 12:52 Page 5
6 UK Helpline 0870 060 2604 Replacement Parts 0870 167 6635 Ireland Helpline 1800 409119
6
DUST CANISTER
Emptying
To obtain the best results from your
cleaner empty the dust canister
regularly, otherwise the airflow and
cleaning power will be reduced.
1 Remove the dust canister from the
product by pressing the dust
canister release button ‹ Lift up the
lid and remove the canister from the
product, pulling the dust canister
away from the product. C
2 Everytime the dust canister is
emptied, turn the yellow dial (a
minimum of 5 revolutions) prior to
pressing the dust canister release
button (this will agitate the fine dust
between the filter pleats and restore
the air flow)
3 Holding the dust canister over a
dustbin press the dust release
button as shown D, the bottom of
the dust container will drop down to
release the dirt.
4 Close the bottom of the dust
canister by pressing the base
upwards until it clicks into place.
5 Refit the dust canister back into the
product. Make certain the dust
canister feet are located in place.
6 Close the lid securely.
ALLERGY
SUFFERERS
If the allergy sufferer is emptying the
product it is recommended that the
container is placed into a plastic bag
to empty.
1 Place the container inside the plastic
bag, releasing the container with one
hand whilst holding the top of the
bag closed with the other, leave the
dust to settle for a few seconds
before carefully removing the empty
canister. The plastic bag can then be
sealed and disposed of.
FILTERS
Cleaning canister
filter
1 To access filter assembly rotate the
canister lid anti-clockwise and lift off
lid E.
2 Use the filter cleaning brush to
remove any fluff from the outside of
the mesh filter or gently tap.
3 Rotate mesh filter anti-clockwise to
disassemble.
4 Shake the pleated filter to remove an
dust.
5 Both the mesh and pleated filters
may be washed (in cool water only)
but must be thoroughly air dried
before refitting.
Locate in the canister and replace
the lid, twisting to lock into place.
IMPORTANT: Do not use detergents
to clean the filter. The filter should be
regularly washed, and must be
thoroughly dry before the machine is
used.
• A spare filter is provided.
• The dust container may not lock
back onto the machine unless the
filter is fitted correctly
Vacuum freshener
(certain models only)
1 After emptying the dust canister and
removing the filters (as described in
points 1-4 above) open the clear
packaging and remove the vacuum
freshener.
2 Place it directly into the dust canister
as shown.F
3 Refit the filters and canister (as
described in point 5 above).
Only place the vacuum freshener
directly into the dust canister. Do not
place in the filter or any other part of
your vacuum cleaner.
New vacuum freshener these can be
purchased from Morphy Richards on
Replacement parts line.
D
E
F
C
71060 Rev5 17/5/06 12:52 Page 6
7www.morphyrichards.com
7
Exhaust filter
The exhaust filter  is located at the
rear of the cleaner. Press the catch
and pull the exhaust grille ‰ away
G. Pull the bottom of the filter
outwards so the top of the filter
unhooks from the filter recess.
Foam filters may be washed (in cool
water), thoroughly air-dried and refitted. The pleated filters used on the
Allergy models cannot be washed
and should be replaced every 6
months or sooner depending on use.
IMPORTANT: To re-fit the filters, first
hook the top of the filter into the
filter recess then push the bottom of
the filter into location H.
Note: If the filter is not correctly
hooked in the exhaust filter grille will
not close.
After fitting the filter, re-fit the
exhaust filter grille by hooking the
bottom of the grille in first and then
pushing the top close until it clicks
fully closed.
IMPORTANT: All filters should be
checked regularly for signs of
damage, preferably after each
cleaning task. The filters must be
replaced immediately if they become
damaged.
• Always disconnect the cleaner from
the mains when checking filters.
• Always make sure all filters are fitted
before use. Failure to do so may
result in damage to your product.
Storage position
When finished you can store the
tubes and accessories by locating
the tube storage clip into the parking
slot on the side of the cleaner as
shown I.
Safety cut-out
If the cleaner overheats a motor
protection thermostat will automatically
switch the motor off. If this happens,
switch the cleaner off, unplug from the
power supply and leave the cleaner to
cool for at least 30 minutes. Check the
airways for blockages, empty dust
canister and clean the filters before
restarting.
Cleaning and
maintenance
Unplug from the mains before
cleaning. The vacuum cleaner,
especially the dust compartment
and all accessories can be cleaned
using a damp cloth or a nonabrasive cleaner and wiped dry.
Purchasing
replacement filters
Use only original Morphy Richards
filters. These can be purchased from
Morphy Richards on Replacement
parts line.
Allergy sufferers
If the allergy suffer is emptying the
product it is recommended that the
container is placed into a plastic bag
to empty.
1 Place the container inside the plastic
bag, releasing the container with one
hand whilst holding the top of the
bag closed with the other, leave the
dust to settle for a few seconds
before removing the canister. The
plastic bag can then be sealed and
disposed of.
information ready to enable our staff
to deal with your query quickly.
I
G
HELPLINE
If you have any difficulty with your
appliance, do not hesitate to call us.
We are more likely to be able to help
than the store from where you
bought it.
Please have the following
• Name of the product
• Model number as shown on the
underside of the appliance.
• Serial number as shown on
underside of the appliance.
UUKK
HHeellpplliinnee
00887700 006600 22660044
RReeppllaacceemmeenntt PPaarrttss
00887700 116677 66663355
IIrreellaanndd HHeellpplliinnee
11880000 440099111199
H
71060 Rev5 17/5/06 12:52 Page 7
8
YOUR TWO YEAR
GUARANTEE
It is important to retain the
retailers receipt as proof of
purchase. Staple your receipt
to this back cover for future
reference.
Please quote the following
information if the product
develops a fault. These
numbers can be found on the
base of the product.
Model no. Serial no.
All Morphy Richards products
are individually tested before
leaving the factory. In the
unlikely event of any appliance
proving to be faulty within 28
days of purchase it should be
returned to the place of
purchase for it to be replaced.
If the fault develops after 28
days and within 24 months of
original purchase, you should
contact the Helpline number
quoting Model number and
Serial number on the product,
or write to Morphy Richards at
the address shown.
You may be asked to return a
copy of proof of purchase.
Subject to the exclusions set
out below (see Exclusions) the
faulty appliance will then be
repaired or replaced and
dispatched usually within 7
working days of receipt.
If you suspect a fault, follow
the simple checks detailed
below before retrying the
appliance or calling the
helpline.
• Check the filters for blockages.
• Check the tools / tubes for
blockages.
• Check the plug is firmly in the
socket is working by trying
another appliance.
• Check the fuse in the plug.
If for any reason this item is
replaced during the 2 year
guarantee period, the
guarantee on the new item will
be calculated from original
purchase date. Therefore it is
vital to retain your original till
receipt or invoice to indicate
the date of initial purchase.
To qualify for the 2 year
guarantee the appliance must
have been used according to
the instructions supplied.
Exclusions
Morphy Richards shall not be
liable to replace or repair the
goods under the terms of the
guarantee where:
1 The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturers
recommendations or where the
fault has been caused by
power surges or damage
caused in transit.
2 The appliance has been used
on a voltage supply other than
that stamped on the products.
3 Repairs have been attempted
by persons other than our
service staff (or authorised
dealer).
4 Where the appliance has been
used for hire purposes or non
domestic use.
5 Morphy Richards are not liable
to carry out any type of
servicing work, under the
guarantee.
6 The guarantee excludes
consumables such as some
filters.
• This guarantee does not confer
any rights other than those
expressly set out above and
does not cover any claims for
consequential loss or damage.
This guarantee is offered as an
additional benefit and does not
affect your statutory rights as a
consumer.
• This guarantee is valid in the
UK and Ireland only.
8
www.morphyrichards.com
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of its
models at any time.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Helpline (office hours)
UK 0870 060 2604
Republic of Ireland 1800 409119
FFoorr ddeettaaiillss ooff ootthheerr pprroodduuccttss iinn tthhee MMoorrpphhyy RRiicchhaarrddss rraannggee pplleeaassee sseeee oouurr wweebbssiittee .. .. ..
For electrical products sold within the
European Community. At the end of the
electrical products useful life it should
not be disposed of with household
waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
71060 Rev5 17/5/06 12:52 Page 8
Loading...