ORIGINAL THERMOCERAMIC STRAIGHTENER
INSTRUCTIONS &
GUARANTEE
Model 22045
STYLING TIPS:
For information on how to create this look and
many others, as well as details of the rest of the
Morphy Richards/I Create product range please visit
our website:
www.morphyrichards.co.uk
HELPLINE:
(8.30-5.00 Mon-Thurs/8.30-4.00 Fri)
UK 0870 060 2614
Republic of Ireland 1800 409119
Morphy Richards’s products are intended for
household use only. Morphy Richards has a policy
of continuous improvement in product quality and
design. The company therefore reserves the right to
change the specification of its models at any time.
Registered address: Morphy Richards Ltd,
Mexborough, South Yorkshire, S64 8AJ
www.morphyrichards.co.uk
PC22045M UK rev 1 4/4
HOW DOES THERMO-:
CERAMIC TECHNOLOGY:
WORK?:
The straightener contains a special thermoceramic
heating element, which ensures it heats up to a very
high temperature in seconds. This high heat is then
maintained throughout use, to guarantee straight
hair all day.
The ceramic coated plates ensure that the hair
cuticle lies flat once styled. This ensures that your
hair reflects light and therefore appears healthy and
shiny. The ceramic coating also acts as a barrier to
protect your hair from the high temperature reached
by the tong. This minimises damage to the cuticle.
DAMAGED CUTICLE
REDUCES LIGHT AND
SHINE POTENTIAL
CERAMIC COATING
ENSURES ‘FLY AWAY’
SECTIONS LIE FLAT
ELEMENT
CERAMIC
COATING
SAFETY INFORMATION:
When using your hair straightener, basic safety
precautions should always be followed. Please read
these instructions carefully before using the product,
and keep them in a safe place for future reference.
nn
1 T
his straightener is professional standard, and
reac
hes very high temperatures.
Alw
ays be careful
not to allow the plates to come into contact with
the skin.
nn
2 Do not leave the plates in contact with the hair for
more than a few seconds.
The straightener reaches
v
ery high temperatures, so there is no need to leave
the hair between the plates for longer than a few
seconds. This will avoid unnecessary damage to the
hair cuticle.
nn
3 Use the appliance for its intended use only
nn
4 To protect against the risk of electric shock, do not
immerse the appliance in w
ater or any other
liquids.
nn
5 It is recommended that this appliance should not be
used by children.
nn
6 Always unplug your appliance when it is not in use.
nn
7 Do not lea
ve the straightener switched on while
unattended.
nn
8 Do not take this product into a bathroom, or use
near w
ater.
nn
9 In the event of cable damage, do not attempt to
replace the mains cable – return to Morph
y
Richards.
nn
10After use, do not store until the product has cooled
do
wn.
nn
11Do not place the str
aightener on surfaces likely to
be damaged by the heat.
WIRING:
This product is fitted with a 13A (BS1363) plug. A 3amp
fuse (BS1362) must be used. Check the voltage on the
rating plate of your appliance corresponds with your
house electricity supply w
hich must be AC (Alternating
current). If the soc
ket outlets in your home are not
suitable for the plug supplied with this appliance the
plug should be remo
ved and an appropriate one fitted.
IMPORTANT: THE PLUG REMOVED FROM THE MAINS
LEAD
, IF SEVERED MUST BE DESTROYED AS A PLUG
WITH BARED FLEXIBLE CORD IS HAZARDOUS IF
ENGA
GED INTO A LIVE SOCKET OUTLET.
MAINS LEAD:
As a safety precaution and to prolong the life of your
appliance, do not wrap the mains lead around the
appliance as this will cause damage.
HOW TO USE YOUR:
STRAIGHTENER:
nn
1 Choose either setting I or II dependent on the
temperature you require. The temperature you
need will depend on the thickness of your hair
and the result you want to achieve. Setting ‘I’ is
the lowest, ‘II’ the highest. The red indicator
light will illuminate when you select the heat
setting required.
nn
2 Once the straightener has reached a temperature
suitable for use, the light will begin to flash. This
usually takes less than 1 minute.
! Ensure your hair is thoroughly dry before you
begin styling – this will avoid damage to the
hair.
nn
3 Divide your hair into sections, brushing each
section thoroughly.
nn
4 Clamp a section of the hair between the
straightening plates, as close to the roots as
possible. Gently slide the straightener down
your hair shaft to the ends. For more difficult
sections of hair, you may need to repeat this.
Avoid leaving your hair clamped inside the
straightener for more than a few seconds, as this
could cause unnecessary damage to the cuticle.
nn
6 To create movement in the hair, use your wrist
to shape the ends either inwards our outwards
depending on the style you wish to achieve.
nn
7 Repeat on all sections of the hair.
nn
8 Clean your straightener regularly for best results.
Always do this when the straightener is switched
off and has cooled down.
VARIABLE
HEAT
SETTINGS
SAFETY
GUARDS
INDICATOR
LIGHT
CERAMIC COATED
STRAIGHTENING
PLATES
RECESSED FINGER WELLS
CLEANING:
It is normal to find build up of hair products on the
straightening plates. In order to avoid this you
should clean your straightener regularly. Always wait
for the plates to cool down thoroughly before
cleaning. Use a damp cloth to remove any build up.
If this fails to clean the plates, try a non abrasive
cleaning wipe e.g. CIF.
2-YEAR GUARANTEE:
It is in your interest to retain the retailers receipt as
proof of purchase. Please quote the model number if
the product develops a fault. This number can be
found on the handle of the product.
All Morphy Richards products are individually tested
before leaving the factory. In the unlikely event of
any appliance proving to be faulty within 28 days of
purchase it should be returned to the place of
purchase for it to be replaced.
If a fault develops after 28 days and within 24
months of original purchase, you should contact the
helpline number quoting the model number of the
product, or write to the address below. You will be
asked to return the product (in secure packaging) to
the address below along with a copy of proof of
purchase:
The After Sales Division,
Morphy Richards Ltd
Mexborough
South Yorkshire
England
S64 8AJ
Loading...