Ironing system (pressurised)
Please read and keep these instructions
TM
Getting the best from your new ironing system....
Safety first
Caution must be used when handling this appliance as it does get very hot. Always
switch off the unit and allow to cool before cleaning or storing.
Water tank
The fixed water tank can be re-filled at any time during ironing.
Performance
To extend the performance and life of your IntelliDome generator, ensure that you
replace the anti-scale filter according to the on-board indicator. Regularly remove any
calcium build-up which may have accumulated in the boiler (see cleaning instructions).
If you have a problem or complaint, please call our dedicated UK based helpline
before returning your product to the retailer from where it was purchased.
UK Helpline: 0844 871 0960
Replacement Parts: 0844 873 0726
Ireland Helpline: 1800 409 119
!
To improve the life of your new product and to ensure the cleanliness of your
clothes, we strongly recommend the use of distilled or demineralised water.
Upon registration with Morphy Richards
(UK & ROI only)
Register online for your 2 year
guarantee. See back of this
instruction book for details.
(UK and Ireland customers only)
www.morphyrichards.co.uk
RN42236 MUK Rev 2
www.homeofthehouseproud.com
www.facebook.com/LoveYourHome
www.twitter.com/LoveYourIroning
For competitions, product hints and tips and much more,
join us online at our blog, Facebook or Twitter pages.
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 1
2
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 2
3
For details of other Morphy Richards products, please see our website:
IMPORTANT SAFETY INSTRUCTIONS 4-6
ELECTRICAL REQUIREMENTS 6
BEFORE USE 6
QUICK START GUIDE 7
COMPONENTS OF YOUR INTELLIDOME 8
CONTROL PANEL FEATURES 9
INSTRUCTIONS FOR USE: TEMPERATURE GUIDE 9
WATER MANAGEMENT 10
STEAM IRONING 11
DRY IRONING 12
WATER SPRAY 12
AUTO STANDBY DEVICE (SAFETY FEATURE) 13
DOUBLE ACTION LIMESCALE REDUCTION SYSTEM 13
FLUSHABLE BOILER FEATURE 14
ROUTINE MAINTENANCE 15
HELPLINE & WEBSITE 15
GUARANTEE 16
CONTENTS
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 3
4
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience or knowledge, if they have
been given supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children shall
not play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
Keep the steam generator and its cord out of
reach of children less than 8 years of age when it
is energized or cooling down.
The steam generator must not be left unattended
while it is connected to the supply mains.
The plug must be removed from the socket-outlet
before the water reservoir is filled with water.
The steam generator must be used and rested on
a stable surface.
When placing the steam generator unit on the
base or its heel, ensure that the surface on which
the heel is placed is stable.
The steam generator is not to be used if it has
been dropped, if there are visible signs of
damage or it is leaking.
IMPORTANT SAFETY INSTRUCTIONS
l
l
l
l
l
l
l
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 4
5
For details of other Morphy Richards products, please see our website:
The use of any electrical appliance requires
the following common sense safety rules:
Primarily there is danger of injury or death
and secondly the danger of damage to the
appliance. These are indicated in the text by
the following two conventions:
WARNING: Danger to the person!
IMPORTANT: Damage to the appliance!
In addition, we offer the following safety
advice.
Location
• Do not use outdoors.
•
Locate the steam generator horizontally on the
rest plate of your ironing board (if large enough)
or on a heat resistant stand at the same height
as your ironing board or below it. Always ensure
the generator is on a firm level surface when
ironing.
• IMPORTANT: Do not use the product on a
surface which could be damaged by heat or
steam such as a worktop or a polished wood
surface.
•
If in doubt, contact Morphy Richards.
Children
• Children do not understand the dangers
associated with operating electrical
appliances. Never allow children to use, or
play with, this appliance.
• Close supervision is necessary when any
appliance is used near children.
Personal Safety
• Do not use the vertical steam feature on
clothes that are being worn.
• WARNING: Burns can occur from touching
hot metal parts, hot water or steam. Use
caution when using your steam generator.
If your iron is placed for a few moments
on the iron rest plate, this plate may reach
very high temperatures. In this instance,
do not touch the iron soleplate or the iron
rest plate until the iron and the iron rest
have cooled down.
• WARNING: To protect against the risk of
electric shock, do not immerse the
appliance in water or in any other liquid.
• Do not leave the steam generator unattended
whilst plugged in or on an ironing board.
Never allow the mains lead to over hang the
work surface.
• The mains socket should always be switched
off before plugging or unplugging from the
socket. Never yank the cord to disconnect
from the socket, instead, grasp the plug and
pull to disconnect.
Other safety considerations
• Use the steam generator only for its intended
use.
• Never hold the steam generator under a tap.
• Always disconnect the steam generator from
the electrical supply when cleaning or when
not in use.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified person(s) in order
to avoid a hazard.
• Do not operate the steam generator with a
damaged cord or if the iron has been
dropped or if there are visible signs of
damage or if it is leaking. To avoid the risk of
electric shock, do not disassemble the iron or
steam generator, but telephone Morphy
Richards for advice. Incorrect reassembly
can cause a risk of electric shock when the
steam generator is used.
• If the need arises to change the mains cable
on your steam generator or the iron, please
return to Morphy Richards service
department at the address on the back page.
• WARNING: Danger
of scalding. Before
attempting to clean
the boiler, always
leave for at least
2 hours.
• WARNING: Take care when opening the
boiler for cleaning, as pressure may be
released to the atmosphere. If this occurs,
allow the pressure to release before
removing the boiler access screw.
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 5
6
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
Special instructions
• If your steam generator does not work, check
the following points:
Has the iron temperature control been set to
the required temperature? Is the plug in its
socket? Is the plug itself or the socket faulty?
(Check by plugging in another appliance).
• To prevent damage to the textile being
ironed, follow the temperature guide carefully.
(Test on the inside of the hem of the
garment).
• If you drop or severely knock your steam
generator, this could cause internal damage
even if the outside appears alright. Have it
checked by a qualified electrician.
• The temperature of accessible surfaces may
be high when the appliance is operating.
ELECTRICAL
REQUIREMENTS
Check that the voltage on the rating plate of
your appliance corresponds with your house
electricity supply which must be A.C.
(Alternating current).
If the socket outlets in your home are not
suitable for the plug supplied with this
appliance, the plug should be removed and
the appropriate one fitted.
WARNING: A damaged or severed mains
cable fitted with a plug should never be
connected to the mains supply. It must
be destroyed, as a damaged cable
becomes hazardous if connected to a
power socket.
Should the fuse in the 13 amp plug require
changing, a 13 amp BS1362 fuse must be
fitted.
WARNING: This appliance must be
earthed.
BEFORE USE
Remove any protective cover from the
soleplate and the base unit, if any.
Unwind and straighten the supply cord ‡
and mains cable ·.
When ironing with the temperature set at
2-dot setting, the steam output should be set
at the lower end of the steam range.
Textiles and clothes are supposed to carry
ironing instructions. If they don’t, you should
follow the fabric guide on page 7, but be sure
to test the temperature by ironing the hem of
the garment or similar area first.
If you turn the control dial down from a hot
setting to a cooler setting, wait until the iron
temperature has stabilised before you
continue ironing
.
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 6
7
For details of other Morphy Richards products, please see our website:
QUICK START GUIDE
1 Unpack the product and remove any
additional packing materials as required.
2 Place the product onto a level surface or
ironing board stand.
3 Make sure the anti-scale drawer ‰ is fully
closed.
4 Using the beaker provided Á or suitable
measuring jug, fill the water tank fl to the full
mark.
5 Set the iron control knob to 3-dot.
6
Connect the unit to the power supply, the LCD
display screen illuminates for 1 second, a short
beep is heard, then the LCD display screen will
turn off. The product is now in STANDBY mode
and the STANDBY ICON will be displayed in the
corner of the LCD display screen A.
7 Press the
POWER
STANDBY
button
on the
control panel and the unit will heat to the
working temperature, the LOW STEAM ICON
will flash whilst the heating cycle takes place
and will remain illuminated when the boiler is
ready to deliver steam B.
Note: At this time, the pump will fill the boiler
with water. You will hear the pump operating,
this is quite normal and will last for
approximately 25 seconds.
8 Press the steam trigger ⁄ to deliver steam to
the iron. Releasing the trigger will extinguish
steam.
9 When ironing is complete, press the
POWER
STANDBY
button
on the control panel to end
the session. The LCD icons will dim until the
unit is disconnected from the mains supply,
only then will the LCD switch off.
10 Allow the unit to cool
, drain the water tank
(see page 10), then
store away
.
AUTO STANDBY DEVICE
(SAFETY FEATURE)
I
f the
unit is
not operated for approximately 15
minutes, it will revert to STANDBY mode and the
POWER STANDBY ICON will flash in the
LCD
display screenC. To re-activate the unit, press
the POWER
STANDBY
button or the
steam
trigger ⁄
and the unit will revert back to the
previous setting.
fl
„
⁄
‰
Á
400ml
‡
·
A
C
B
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 7
8
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
fl
·
fi
›
‡
¤
‹
⁄
‡
‚
COMPONENTS OF YOUR INTELLIDOME
„ Control panel (see page 9)
ÊÂ
UNDERSIDE VIEW
Á
400ml
Iron unit
⁄ Steam trigger
¤ Temperature indicator light
‹ Temperature control knob
› Soleplate
Base unit
fi Water tank filler cap
fl Water tank
‡ Supply cord (steam)
· Mains cable
‚ Cable storage clip
„ Control panel
‰ Anti-scale filter drawer
Filter cartridge
(see page 13)
 Boiler access screw and cover
(cleaning only)
Ê Boiler access tool
Á Filler cup
Î/Ï/Ì/Ó
Spray feature (see page 12)
Ë/È/Í
Water tank drain (see page 10)
‰/
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 8
9
For details of other Morphy Richards products, please see our website:
Symbol
(120°C Max) Cool
(160°C Max) Warm
(210°C Max) Hot
Control knob
positions
Do not iron
at all
Fabric
Nylon, Acetates
e.g. Acrilan
Courtelle, Orlon
Wool, Polyester
mixtures e.g.
Polyester/Cotton
Triacetates, e.g.
Tricel/Polyester
Cotton, Linen
Rayon, Rayon
mixtures,
e.g. Rayon/Linen
Ironing
Iron on the wrong
side, if moisture
required use damp
cloth (Not Acetate)
Fabrics requiring this
setting usually require
steam pressing for heavy
cotton, denim etc.
Steaming
Dry
‘Max setting’
INSTRUCTIONS FOR USE
Temperature guide
Low steam settings High steam settings
The control consists of an
LCD display screen
and 3 buttons: POWER
STANDBY
button
1
and STEAM SETTING +/- buttons 4, as shown
below D:
POWER
STANDBY
button
Intellidome outline
LCD display screen
Steam level +/Standby mode
Clean boiler / fill boiler indicator
Anti-scale filter
Anti-scale filter alignment arrows
Anti-scale drawer display
Boiler outline
Low water display
No steam
Low steam level
Medium steam level
High steam level
1 2
3 4
5
6 7 8 9 10111213 1415
D
CONTROL PANEL FEATURES
„
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 9
10
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
1. WATER MANAGEMENT
Filling
1 Place the steam generator on a stable ironing
board or table, with the iron resting on its
stand.
2 Open the filler cap at the front of the water
tank and fill to the FILL TO HERE line using
the filler cup Á provided or a suitable jug.
WE RECOMMEND YOU USE DISTILLED OR
DEMINERALISED WATER IN THIS UNIT.
Never use battery topping up fluid or water
containing any substances like starch or
sugar, or defrosted water from a refrigerator.
3 Always drain out any remaining water after
use (see instructions below).
Re-filling ‘in use’
1 Refilling can be done whilst the appliance is
in operation. It is not necessary to wait for
the appliance to cool down.
2 Open the filler cap at the front of the water
tank and fill as necessary.
Low water cutout
E
The unit has an electronic system to monitor the
water level. When the level is low, the LOW
WATER ICONS 6/11will flash and a beep will
be heard for 10 seconds to warn the user to refill
the tank. Once the unit has been filled, the LOW
WATER ICONS will disappear.
NOTE: When the LOW WATER WARNING
ICONS activate, the boiler will still deliver steam
for a short period then the unit will switch off,
this action saves the unit from damage.
Draining the water tank
F
When ironing is complete, we advise you to
empty any water left in the tank.
This model is fitted with a drain system situated
at the front of the unit.
1 Disconnect the unit from the mains supply.
2 Place the unit on the sink drainer so water can
run away safely.
3 Push back the drain release catch Í and rotate
the tube Ë outwards using the tab È.
4 Water will now drain automatically.
5 Once the tank is empty, replace the tube making
sure it clips in place.
E
Water tank drain
Ë Drain tube
È Drain tube tab
Í Drain tube
release catch
Í
ÈË ÈË
Í
Slide in this
direction
Rotate tube
outwards
F
6 11
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 10
11
11
For details of other Morphy Richards products, please see our website:
1
Unwind and straighten the supply and power
cords (‡ and ·).
2
Fill the water tank with clean tap water (see
page 10).
3
Connect the unit to the mains supply.
The LCD display screen „ will illuminate for
1-second and be accompanied with a short
beep sound, then the unit will turn off and will
remain in STANDBY mode until re-activated.
The STANDBY ICON is also visible in the
corner of the display screen.
4
Press the POWER STANDBY button to activate
the unit and set the iron temperature control
dial on the iron to the 3-dot setting.
At this time, the pump will fill the boiler with
water. You will hear the pump operating - this
is quite normal. The filling sequence takes
approximately 25 seconds.
The unit will heat and automatically default to
the LOW STEAM level, the STEAM ICON will
flash on the display screen and will remain
permanently on when steam is available for
ironing.
The AUTO STANDBY feature will activate if
the iron is not used for 15 minutes. Press the
POWER STANDBY
button or steam trigger to
reactivate the iron.
Steam settings
To increase or decrease the steam setting, press
the STEAM SETTING +/- buttons. These
settings include:
NO STEAM G,
LOW STEAM LEVELH,
MEDIUM STEAM LEVEL
I
and HIGH STEAM LEVELJ.
LOW STEAM LEVEL
MEDIUM STEAM LEVEL
HIGH STEAM LEVEL
The STEAM ICON will flash until the unit reaches
the selected temperature. Once the temperature
has been reached, the STEAM ICON will remain lit.
When navigating though the steam settings, a
SHORT BEEP will be heard for every operation
of the STEAM SETTING +/- buttons a further
LONGER BEEP will be heard once the unit has
reached the selected setting.
Note: During ironing, the pump will operate
periodically to ‘top up’ the boiler with water.
This is quite normal and lasts for a few
seconds only.
VERTICAL STEAM
Hold the iron in a
vertical position
between 1cm and 2cm
away from the item K .
Press the steam trigger
⁄, this will create
vertical steam. This
feature is especially
useful for removing
creases from hanging
clothes, curtains, wall
hangings etc.
STEAM FUNCTION
During the steaming process, small amounts of
water may be ejected from the soleplate. This is
normal and can be avoided by using the steam
for short amounts of time and only when the iron
is at the correct temperature (the indicator light
on the iron goes out when ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do
not move the base unit during ironing. We
recommend for the first time ironing that you
iron over an old towel.
2. STEAM IRONING
G
H
I
J
K
NO STEAM
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 11
12
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
3. DRY IRONING
Always make sure there is water in the tank
otherwise the LOW WATER indicator will
activate.
1 Always make sure the water tank is quarter
full, otherwise the LOW WATER INDICATOR
ICON will activate.
2 Connect the unit to the mains supply.
3 The LCD display screen will illuminate for 1
second accompanied by a short beep sound,
the unit will then turn off and will remain in
STANDBY mode until re-activated. The
STANDBY ICON will be visible in the corner
of the display screen.
4 Press the
POWER
STANDBY
button
to
activate the unit and set the iron temperature
dial to the dot setting required.
5 Press the STEAM +/– buttons until the
NO STEAM ICON is displayed on the LCD
display screen L.
NO STEAM
6 Turn the temperature dial on the iron to the
dot setting required.
7 The temperature indicator light on the iron
will glow indicating the iron is heating.
8 When the required temperature is reached,
the temperature indicator light will go out and
the iron is now ready to use. It is always a
good idea to begin with “cool fabrics” and
work up to higher settings. An iron heats up
quicker than it cools down so you’ll save
time and electricity.
9 The AUTO STANDBY feature will activate if
the iron is not used for 15 minutes. Press the
POWER
STANDBY
button or the iron
steam
trigger ⁄ to reactivate the unit.
WATER SPRAY (certain models only)
Certain models are fitted with a water spray
feature. Stubborn creases and excessively
dry clothing can be softened by damping the
material with water. This procedure means
ironing can be achieved without applying
excessive pressure.
Filling water spray tank
M
To fill the water spray tank with water, press
the release button Ì and lift away the spray
unit Î.
Pull the tank Ó away from the spray unit in a
downward direction, taking care not to
damage the tank, and fill water to the ‘Full’
mark.
Water spray unit (certain models only)
Î Spray unit assembly
Ï Spray button
Ì Spray unit release button
Ó 20ml spray bottle
Re-assembly
M
Attach the tank to the spray unit, taking care
to align the parts correctly.
Locate the spray unit to the front of the iron
and press it home until the unit locks into
place.
Press the pump Ï a few times to purge the
air from the system, when a fine mist of
water is created, the unit is ready for use.
L
Î
Ó
Ì
Ï
Î
M
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 12
13
For details of other Morphy Richards products, please see our website:
4. AUTO STANDBY DEVICE (SAFETY FEATURE)
If any of the function buttons are not operated for
approximately 15 minutes, the unit will revert to
STANDBY mode and the POWER STANDBY ICON
will flash in the LCD display N. To re-activate the
unit, press the POWER
STANDBY
button or the
iron
steam trigger ⁄
and the unit will revert back
to the previous setting.
5. DOUBLE ACTION LIMESCALE REDUCTION SYSTEM
CHANGING THE FILTER
IMPORTANT: This procedure must be
done when the unit is connected to the
mains supply.
The anti-scale filter is designed to reduce the
build-up of limescale which occurs during
steam ironing, this will prolong the working
life of your iron. However, please note that
the anti-scale filter will not completely stop
the natural process of limescale
build-up.
When the anti-scale filter needs replacing, the
FILTER ICONS will flash on the LCD screen
O
accompanied by a loud beep noise, when this
occurs, continue ironing until complete then we
suggest you change the filter.
Remove the filter drawer
‰ to r
eplace the filter
cartridge . Please wait approximately 10
seconds before replacing the drawer to allow
the onboard timer circuit to reset.
If the change filter instruction is ignored, the unit
will still function, however the product life may
be affected.
Incorrect filter installation
If the filter is installed incorrectly, the FILTER
ICONS will illuminate P, accompanied by a
LONGER BEEP.
Once the filter is aligned correctly, the icons will
disappear.
Replacing the filter
The filter
cartridge
is situated inside the
filter drawer ‰ below the LCD screen Q.
To replace the filter, simply pull out the
drawer and replace the filter R.
Replace the drawer making sure it is pushed
firmly into position.
Replacement filters
To obtain replacement filters, telephone
our spares number on: 0844 873 0726.
• If a new filter is not available, you may
continue operating the appliance, but scale
will build up in the system. Replace the filter
as soon as possible. Part Number 01030.
R
Filter
Cartridge
‰
Filter
Drawer
Q
N
O
P
‰/
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 13
14
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
FLUSHABLE BOILER
FEATURE
To extend the life of the product we recommend
you periodically rinse out the boiler to remove
any limescale build-up.
•
When the boiler needs cleaning, the icons below
will be displayed on the LCD screen S.
WARNING: Only clean the boiler when the
unit is cold. If cleaning takes place after
ironing, please allow 2 hours for the
boiler to cool to ambient temperature.
1 When the CLEAN BOILER ICON is displayed on
the LCD screen, finish ironing, drain the water
tank
(see tank drain instruction, pages 10)
and leave the unit for a few hours until cold.
2 Stand the steam generator close to the sink
drainer. Ensure all water is drained from the
water tank (see page 10).
3 Remove the iron from its rest.
4 Turn the base unit upside down and unclip the
cover to expose the boiler access screw  T.
Type A cover folds back to expose the boiler
access screw, type B cover rotates to the side.
5 Use the tool Ê provided to remove the screw in
an anti-clockwise direction U.
6
Fill the filler cup to the MAX mark with ordinary
tap water and pour this through the access hole
into the boiler V.
7 Move the base unit back and forth a few times
then pour the water out into the sink or
container W.
8 Repeat this procedure a number of times until
the water is clean and clear, making sure all
water is removed.
9 Replace the boiler access screw using the tool
provided but do not use excessive force X.
10 Reposition the cover and place the tool in the
space provided, ensuring it is securely clipped
into place.
The cleaning procedure is now complete.
W
X
V
U
S
Type A cover Type B cover
T T
Unclip and
pull back
Unclip and
rotate
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 14
15
For details of other Morphy Richards products, please see our website:
ROUTINE
MAINTENANCE
Soleplate cleaning
To clean a stainless steel soleplate
To keep the soleplate of your iron clean and free
of limescale, we recommend that you use one of
the gentle chrome, silver or stainless steel
cleaners that are generally available. Always
follow the manufacturer’s instructions. To clean
off melted man-made fibres, set the iron at 3-dot
position and pass it over a clean piece of cotton
which will draw the deposit off the surface.
To clean a coated soleplate
In the unlikely event of any man-made fibre
fusing to the soleplate, set the iron at the
3-dot position and pass it over a clean piece of
cotton, this will draw the deposit off the surface.
Do not use scouring powder or solution, as this
could cause damage to the coating.
To clean the exterior
Allow the steam generator to cool and wipe over
with a damp cloth and mild detergent, then wipe
with a dry cloth.
HELPLINE
If you have any difficulty with your appliance, do
not hesitate to call us.
We are more likely to be able to help than the
store from where you bought it.
Please have the following information ready to
enable our staff to deal with your query quickly.
• Name of the product
• Model number as shown on the underside of the
appliance.
• Serial number as shown on underside of the
appliance.
UK Helpline 0844 871 0960
Replacement Parts 0844 873 0726
Ireland Helpline 1800 409 119
WEBSITE
You may also contact us through our website,
or visit the site to browse and purchase
appliances, spare parts and accessories from
the extensive Morphy Richards range.
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 15
16
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company therefore, reserves the right to change the specification of
its models at any time.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Helplines (office hours)
UK 0844 871 0960
Spare Parts 0844 873 0726
Republic of Ireland 1800 409 119
RN42236 MUK Rev 2 10/10
REGISTERING
YOUR TWO YEAR
GUARANTEE
Your standard one year guarantee is
extended for an additional 12
months when you register the
product within 28 days of purchase
with Morphy Richards. If you do not
register the product with Morphy
Richards within 28 days, your
product is guaranteed for 1 year. To
validate your 2 year guarantee
register with us online at
www.morphyrichards.co.uk
N.B. Each qualifying product needs
to be registered with Morphy
Richards individually.
Please note that the 2 year
guarantee is only available in the
UK and Ireland. Please refer to the
one year guarantee for more
information.
YOUR ONE YEAR
GUARANTEE
It is important to retain the retailer’s
receipt as proof of purchase. Staple
your receipt to this back cover for
future reference.
Please quote the following
information if the product develops
a fault. These numbers can be
found on the base of the product.
Model no.
Serial no.
All Morphy Richards products are
individually tested before leaving the
factory. In the unlikely event of any
appliance proving to be faulty within
28 days of purchase, it should be
returned to the place of purchase
for it to be replaced.
If the fault develops after 28 days
and within 12 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy
Richards at the address shown.
You may be asked to return a copy
of proof of purchase.
Subject to the exclusions set out
below (see Exclusions), the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.
If, for any reason, this item is
replaced during the 1 year
guarantee period, the guarantee on
the new item will be calculated from
original purchase date. Therefore it
is vital to retain your original till
receipt or invoice to indicate the
date of initial purchase.
To qualify for the 1 year guarantee,
the appliance must have been used
according to the instructions
supplied. For example, filters should
have been emptied regularly.
EXCLUSIONS
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
1 The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturer’s
recommendations or where the fault
has been caused by power surges
or damage caused in transit.
2 The appliance has been used on a
voltage supply other than that
stamped on the products.
3 Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
4 The appliance has been used for
hire purposes or non domestic use.
5 The appliance is second hand.
6 Morphy Richards are not liable to
carry out any type of servicing
work, under the guarantee.
7 Plastic filters for all Morphy
Richards kettles and coffee makers
are not covered by the guarantee.
8 Batteries and damage from leakage
are not covered by the guarantee.
• This guarantee does not confer any
rights other than those expressly set
out above and does not cover any
claims for consequential loss or
damage. This guarantee is offered
as an additional benefit and does
not affect your statutory rights as a
consumer.
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should
not be disposed of with household
waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
UK
Helpline 0870 060 2614 Replacement Parts 0870 157 6645 Ireland Helpline 1800 409119
RN42236MUK Rev2_Instruction Book 25/10/2010 11:38 Page 16
Loading...