wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
PPrreecciissee SStteeaamm IIrroonn
steam/spray shot
Please read and keep these instructions
GGeettttiinngg tthhee bbeesstt ffrroomm yyoouurr nneeww iirroonn........
Safety first
Caution must be used when handling this appliance as it
does get very hot. Always switch off the unit and allow to
cool before cleaning or storing.
Self cleaning button
Your iron will give the best ironing results and will last longer
if you use the self clean feature at least once a month.
RN40725 MUK Rev 4
For replacement parts, help with using your Morphy Richards,
problems and lots more, contact us by phone or through our website.
UK Helpline: 0870 060 2615
Replacement parts: 0870 167 6646
Ireland 1800 409119
40725 rev4 28/8/07 15:32 Page 1
22
IMPORTANT
SAFETY
INSTRUCTIONS
The use of any electrical
appliance requires the
following common sense
safety rules.
Primarily there is danger of
injury or death and
secondly the danger of
damage to the appliance.
These are indicated in the
text by the following two
conventions:
WWAARRNNIINNGG:: DDaannggeerr ttoo tthhee
ppeerrssoonn
IMPORTANT: Damage to
the appliance! In addition
we offer the following
safety advice.
Location
• Do not use outdoors.
Mains lead
• Do not allow the mains
lead to become strained or
run this appliance over it.
• If the electrical cable
becomes damaged the
cable assembly must be
replaced. Do not attempt
this task yourself, contact
the helpline number that is
found at the bottom of the
page.
Personal safety
•• WWAARRNNIINNGG:: BBuurrnnss ccaann
ooccccuurr ffrroomm ttoouucchhiinngg hhoott
mmeettaall ppaarrttss,, hhoott wwaatteerr oorr
sstteeaamm.. UUssee ccaauuttiioonn wwhheenn
yyoouu ttuurrnn aa sstteeaamm iirroonn
uuppssiiddee ddoowwnn,, tthheerree mmaayy
bbee hhoott wwaatteerr iinn tthhee wwaatteerr
ttaannkk..
•• WWAARRNNIINNGG:: TToo pprrootteecctt
aaggaaiinnsstt tthhee rriisskk ooff
eelleeccttrriicc sshhoocckk ddoo nnoott ppuutt
tthhee aapppplliiaannccee iinn wwaatteerr oorr
iinn aannyy ootthheerr lliiqquuiidd..
• Do not use the vertical
steam feature on clothes
that are being worn.
• Do not leave the iron
unattended whilst plugged
in or on an ironing board.
Never allow the mains lead
to over hang the work
surface.
• The socket should always
be off before plugging or
unplugging from the
socket. Never yank the
cord to disconnect from
the socket, instead, grasp
plug and pull to
disconnect.
• Do not allow the cord to
touch hot surfaces. Let the
iron cool completely before
putting away. Loop cord
loosely around the iron
before storing.
• The iron must be used and
rested on a stable surface
• When placing the iron on
its heel, ensure that the
surface on which the iron is
placed is stable.
• The iron is not to be used if
it has been dropped, if
there are visible signs of
damage or if it is leaking.
• This appliance is not
intended for use by
persons (including children)
with reduced physical,
sensory or mental
capabilities, or lack of
experience or knowledge,
unless they have been
given supervision or
instruction concerning the
use of the appliance by a
person responsible for their
safety.
Other safety
considerations
• Use the iron only for its
intended use.
• Always disconnect the iron
from the electrical socket
when filling with water or
emptying, and when not in
use.
• Do not operate the iron
with a damaged cord or if
the iron has been dropped
or damaged. To avoid the
risk of electric shock, do
not disassemble the iron,
but telephone Morphy
Richards for advice.
Incorrect reassembly can
cause a risk of electric
shock when the iron is
used.
Children
• Close supervision is
necessary when any
appliance is used near
children.
• Children do not understand
the dangers associated
with operating electrical
appliances.
• Children should be
supervised to ensure that
they do not play with this
appliance.
Special
instructions
• If your iron does not work,
check the following points:
Has the temperature
control been set to the
required temperature? Is
the plug in its socket? Is
the plug itself or the socket
faulty? (Check by plugging
in another appliance).
•
WWAARRNNIINNGG:: WWhheenn nnoott iinn
uussee,, yyoouurr iirroonn sshhoouulldd
nneevveerr bbee ppllaacceedd ffllaatt aanndd
lleefftt oonn aann iirroonniinngg bbooaarrdd..
• To prevent damage to the
textile being ironed, follow
the temperature guide
carefully. (Test the inside of
the hem of the garment).
• When ironing is complete,
turn off the steam selector
switch, remove the plug
from the socket, empty any
remaining water from the
tank, and allow to cool
before storage.
UUKK HHeellpplliinnee 00887700 006600 22661155 RReeppllaacceemmeenntt PPaarrttss 00887700 116677 66664466 IIrreellaanndd HHeellpplliinnee 11880000 440099111199
40725 rev4 28/8/07 15:32 Page 2
Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of
the International Textile Care Labelling Code.
• If you drop or severely
knock your iron this could
cause internal damage
even if the outside appears
alright. Have it checked by
a qualified electrician.
• It is recommended that you
use up one beaker of water
by operating your iron’s
steam and shot of steam
functions before ironing
any clothes as some
dripping may occur while
your irons steam system is
activated.
Electrical
requirements
Check that the voltage on
the rating plate of your
appliance corresponds
with your house electricity
supply which must be A.C.
(Alternating current).
If the socket outlets in your
home are not suitable for
the plug supplied with this
appliance, the plug should
be removed and the
appropriate one fitted.
WWAARRNNIINNGG:: TThhee pplluugg
rreemmoovveedd ffrroomm tthhee mmaaiinnss
lleeaadd,, iiff sseevveerreedd,, mmuusstt bbee
ddeessttrrooyyeedd,, aass aa pplluugg wwiitthh
aa bbaarreedd fflleexxiibbllee ccoorrdd iiss
hhaazzaarrddoouuss iiff eennggaaggeedd
iinnttoo aa lliivvee ssoocckkeett oouuttlleett..
Should the fuse in the 13
amp plug require changing,
a 13 amp BS1362 fuse
must be fitted.
WWAARRNNIINNGG:: TThhiiss
aapppplliiaannccee mmuusstt bbee
eeaarrtthheedd..
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
Symbol
(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot
Control knob
positions
Do not iron
at all
Fabric
Nylon, Acetates
e.g. Acrilan
Courtelle, Orlon
Triacetates, e.g.
Tricel/Polyester
Wool, Polyester
mixtures e.g.
Polyester/Cotton
Cotton, Linen
Rayon, Rayon
mixtures,
e.g. Rayon/Linen
Ironing
Iron on wrong side
if moisture required
use damp cloth
(Not Acetate)
Fabrics requiring this
setting usually require
steam pressing for heavy
cotton, denim etc.
With water in tank Dry and spray
Steam/spray/
shot of steam
Without water in tank Dry ironing
‘Max setting’
Self clean
INSTRUCTIONS FOR USE
33
Temperature guide
40725 rev4 28/8/07 15:32 Page 3
44 UUKK HHeellpplliinnee 00887700 006600 22661155 RReeppllaacceemmeenntt PPaarrttss 00887700 116677 66664466 IIrreellaanndd HHeellpplliinnee 11880000 440099111199
COMPONENTS OF
YOUR IRON
⁄⁄
Steam to dry iron selector
switch
¤¤
Temperature control dial
‹‹
Steam level indicator window
››
Spray button
fifi
Shot of steam button
flfl
Temperature indicator light
‡‡
Water tank (illuminated certain
models)
··
Soleplate
‚‚
Self-clean button
„„
Spray nozzle
‰‰
Filling hole with cap
ÂÂ
Filler cup (300ml)
ÊÊ
Auto shut-off feature (certain
models only)
BEFORE USE
Sort out the items to be ironed
according to the type of fabric.
This will minimise the frequency
of temperature adjustment for
different garments.
Note: The steam facility should
only be used on garments which
are suitable for ironing at the 2
and 3 dot settings.
Textiles and clothes are
supposed to carry ironing
instructions. If they don’t you
should follow the fabric guide on
page 3, but be sure to test the
temperature by ironing the hem
of the garment or similar area
first.
If you turn the control dial down
from a hot setting to a cooler
setting, wait until the iron
temperature has stabilised
before you continue ironing.
Delicate fabrics such as silk,
wool,velour, etc, are best ironed
with an ironing cloth to prevent
shine marks.
fl
‡
·
‚
„
‰
Â
400
350
300
⁄
¤
‹
›
fi
Ê
40725 rev4 28/8/07 15:32 Page 4
55wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
FILLING
AA
11
Make sure that the iron is not
plugged in, then set the steam
to dry iron selector switch
⁄⁄
to
the position before filling the iron
with water.
22
Lift up the filler cap and fill the
tank
‡‡
with water through the
filling hole ‰‰, using the beaker
provided (300ml).
AA ÂÂ
After
filling replace the filler cap. In
hard water areas the use of
distilled or demineralised water
is recommended.
WWAARRNNIINNGG:: NNeevveerr uussee bbaatttteerryy
ttooppppiinngg uupp fflluuiidd oorr wwaatteerr
ccoonnttaaiinniinngg aannyy ssuubbssttaanncceess
lliikkee ssttaarrcchh,, oorr ssuuggaarr,, oorr
ddeeffrroosstteedd wwaatteerr ffrroomm aa
rreeffrriiggeerraattoorr..
33
Always pour out the remaining
water after use.
WWAARRNNIINNGG:: WWhheenn ffiilllliinngg yyoouurr
iirroonn wwiitthh ttaapp wwaatteerr aallwwaayyss
uussee tthhee bbeeaakkeerr pprroovviiddeedd..
NNeevveerr ffiillll ddiirreeccttllyy uunnddeerr tthhee
ttaapp..
TEMPERATURE
CONTROL
BB
Plug in the iron and switch on.
Set the temperature control dial
¤¤
to the temperature required,
but don’t start ironing
immediately.
If you wait a few minutes, the
iron will stabilise at the required
setting. Your Morphy Richards
iron is fitted with an indicator
light flflwhich will go on and off
while you are ironing.
This is perfectly normal as it
shows that the iron is
maintaining the heat setting you
have chosen.
It is always a good idea to begin
with cool fabrics and work up to
higher settings.
An iron heats up quicker than it
cools down so you’ll save time
and electricity.
FEATURES OF YOUR
IRON
Temperature indicator
light
The indicator light flflshows that
the iron is warming up. When
the required temperature is
reached the light will go out and
will cycle on-off during
operation.
Dry ironing
You can use your iron as a dry
iron only. Make sure the steam
to dry iron selector switch⁄⁄is
set to the symbol.
Any temperature setting may be
used depending on the
garment. The spray feature may
be used provided there is water
in the tank (see filling section).
You do not need to put any
water in the tank when dry
ironing only.
Spray
CC
Press the spray button ››and
aim the spray of water at
stubborn creases. You can do
this whilst dry ironing providing
there is water in the tank. When
using the water spray it may be
necessary to push the button a
few times to get the spray pump
primed.
Automatic variable
steam
BB
Fill the iron with water as
described in the filling section,
and insert the plug into the
electrical socket.
11
Set the ‘steam to dry iron’
selector switch to steam ⁄⁄.
22
Select the temperature required
by turning the temperature
control dial
¤¤
to the desired
setting. The amount of steam
required is automatically
selected and is displayed in
window ‹‹.
A
BB
CC
40725 rev4 28/8/07 15:32 Page 5
66 UUKK HHeellpplliinnee 00887700 006600 22661155 RReeppllaacceemmeenntt PPaarrttss 00887700 116677 66664466 IIrreellaanndd HHeellpplliinnee 11880000 440099111199
Press the shot of steam button
fifi
to obtain a burst of extra
steam for ironing out creases in
heavy material such as denim
etc.
The shot of steam can be used
whilst dry ironing, providing
there is water in the tank, and
the temperature control is set
within the steam range.
Do not use shot of steam at
temperatures below the steam
range (2-DOT) shown on the
control dial.
Note: For optimum steam
quality, do not operate the shot
more than three times in
succession.
Vertical steam
Hold the iron in a vertical
position between 1cm and 2cm
away from the item EE. Press
the shot of steam button fifi,
this will create vertical steam.
This feature is especially useful
for removing creases from
hanging clothes, curtains, wall
hanging, etc.
Note; For optimum steam
quality, do not operate the shot
more than three times in
succession.
No drip system
Your iron is fitted with a no drip
system which is designed to
prevent water escaping from the
soleplate when the iron is too
cold.
During use, the no drip system
may emit a loud click,
particularly during heat-up or
whilst cooling down. This is
perfectly normal and indicates
that the system is functioning
correctly.
Auto shut-off
(certain models only)
If your iron is fitted with the auto
shut-off function it will
automatically shut down after a
set period.
If the iron is left unattended in
the horizontal position it will
shut down after 1 minute. When
this occurs, the indicator light
will flash and a beep will be
heard.
If it is left in the vertical position
it will shut down after 8 minutes.
To reactivate the iron gently
shake it, the temperature
indicator light will come on
indicating the iron is warming
up and wait for the iron to heatup as normal.
LIFE LONG ANTISCALE SYSTEM
(certain models only)
The life long anti-scale system
reduces scale deposits and
helps prolong the life of the iron.
EMPTYING AND
STORING
When you have finished ironing,
unplug your iron. Ensure that
the steam to dry iron selector
switch ⁄⁄is set at the
position, lift up the fill cap and
empty any remaining water out
of the filling hole
FF..
Do not store in the box, but in
an upright position, so that any
drops of water remaining
cannot leak out and discolour
the soleplate
GG..
Important: The flex can be
damaged if wound too tightly
around the iron after use. Make
a loose loop with the flex and
wrap it around the iron. The iron
must be cool before winding the
flex and storing on its heel.
MAINTENANCE
Self clean feature
11
Half fill the iron with water.
22
Place the iron on its heel.
33
Connect to a mains supply
outlet
44
Turn the temperature dial to
‘MAX’ setting
EE
FF
GG
40725 rev4 28/8/07 15:32 Page 6
77wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
55
The pilot light will glow
indicating the irons switched on.
66
The pilot light will go off when
the required temperature is
reached.
77
Wait for one more cycle; (pilot
light glows and goes off.)
88
Turn the temperature dial in anticlockwise direction to ‘Min’
99
Disconnect the iron from mains
supply outlet.
1100
Hold the iron horizontally over a
sink.
1111
Press and hold down the SelfCleaning button.
1122
Steam and boiling hot water will
drain from the holes in the the
soleplate washing away the
scale and minerals that have
built up inside the Steam
Chamber.
1133
Gently move the iron back and
forth until the water tank is
empty.
1144
When Self-Cleaning is complete,
release the Self-Cleaning button.
1155
Rest your steam iron back on its
heel and allow to fully cool
down.
1166
Wipe the soleplate with a cold
damp cloth.
WWAARRNNIINNGG:: KKeeeepp hhaannddss aanndd
bbooddyy aawwaayy ffrroomm tthhee hhoott
wwaatteerr..
WWAARRNNIINNGG:: DDoo nnoott aatttteemmpptt ttoo
ddeessccaallee tthhee ssoolleeppllaattee wwiitthh
ddeessccaalliinngg pprroodduuccttss..
To clean a stainless
steel soleplate
To keep the soleplate of your
iron clean and free of limescale,
we recommend that you use
one of the gentle chrome, silver
or stainless steel cleaners that
are generally available. Always
follow the manufacturer’s
instructions.
To clean off melted man-made
fibres, set the iron at 3 dot
position and pass it over a clean
piece of cotton which will draw
the deposit off the surface.
To clean a coated
soleplate
(certain models only)
In the unlikely event of any man-
made fibre fusing to the
soleplate, set the iron at the 3
dot position and pass it over a
clean piece of cotton which will
draw the deposit off the surface.
Do not use scouring powder or
solution as this could cause
damage to the coating.
To clean the exterior
Allow the iron to cool and wipe
over with a damp cloth and mild
detergent, then wipe with a dry
cloth.
HELPLINE
If you have any difficulty with
your appliance, do not hesitate
to call us.
We are more likely to be able to
help than the store from where
you bought it.
Please have the following
information ready to enable our
staff to deal with your query
quickly.
• Name of the product
• Model number as shown on the
underside of the appliance.
• Serial number as shown on
underside of the appliance.
UK Helpline 0870 060 2615
Replacement Parts 0870 167 6646
Ireland Helpline 1800 409119
40725 rev4 28/8/07 15:32 Page 7
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of its
models at any time.
TThhee AAfftteerr SSaalleess DDiivviissiioonn
MMoorrpphhyy RRiicchhaarrddss LLttdd
Mexborough, South Yorkshire,
England, S64 8AJ
Helpline (office hours)
UK 0870 060 2615
Republic of Ireland 1800 409119
RN40725 MUK Rev 4 08/07
For details of other products in the Morphy Richards range please see our website . . .
YOUR TWO YEAR
GUARANTEE
It is important to retain the
retailers receipt as proof of
purchase. Staple your
receipt to this back cover
for future reference.
Please quote the following
information if the product
develops a fault. These
numbers can be found on
the base of the product.
Model no.
Serial no.
All Morphy Richards
products are individually
tested before leaving the
factory. In the unlikely event
of any appliance proving to
be faulty within 28 days of
purchase it should be
returned to the place of
purchase for it to be
replaced.
If the fault develops after 28
days and within 24 months
of original purchase, you
should contact the Helpline
number quoting Model
number and Serial number
on the product, or write to
Morphy Richards at the
address shown. You may be
asked to return a copy of
proof of purchase.
Subject to the exclusions
set out below (see
Exclusions) the faulty
appliance will then be
repaired or replaced and
dispatched usually within 7
working days of receipt.
If for any reason this item is
replaced during the 2 year
guarantee period, the
guarantee on the new item
will be calculated from
original purchase date.
Therefore it is vital to retain
your original till receipt or
invoice to indicate the date
of initial purchase.
To qualify for the 2 year
guarantee the appliance
must have been used
according to the
manufacturers instructions.
For example kettles should
have been regularly
descaled.
EXCLUSIONS
Morphy Richards shall not
be liable to replace or
repair the goods under the
terms of the guarantee
where:
11
The fault has been caused
or is attributable to
accidental use, misuse,
negligent use or used
contrary to the
manufacturers
recommendations or where
the fault has been caused
by power surges or
damage caused in transit.
22
The appliance has been
used on a voltage supply
other than that stamped on
the products.
33
Repairs have been
attempted by persons other
than our service staff (or
authorised dealer).
44
Where the appliance has
been used for hire
purposes or non domestic
use.
55
Morphy Richards are not
liable to carry out any type
of servicing work, under the
guarantee.
66
Plastic filters for all Morphy
Richards kettles and coffee
makers are not covered by
the guarantee.
• This guarantee does not
confer any rights other than
those expressly set out
above and does not cover
any claims for
consequential loss or
damage. This guarantee is
offered as an additional
benefit and does not affect
your statutory rights as a
consumer.
• This guarantee is valid in
the UK and Ireland only.
88
For electrical products sold within the
European Community. At the end of the
electrical products useful life it should
not be disposed of with household
waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
40725 rev4 28/8/07 15:32 Page 8
Loading...