RN332007 MUK Rev1
* Register online for your 2 year guarantee. See back of this instruction book for details. (UK and Ireland customers only)
Please read and keep these instructions for future use
Steam Generator
www.morphyrichards.co.uk/blog
For competitions, product hints and tips
and more join us at
www.facebook.com/morphyrichardsuk
@loveyourmorphy
IMPORTANT: To prevent limescale problems which would not be covered by
the guarantee, we recommend the use of a mix of 50% tap water and 50%
distilled or demineralised water (available from most large supermarkets).
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 1
2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•
This appliance can be used by persons with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, if they have been given
supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards
involved.
•
Children shall not play with the appliance.
•
Keep the appliance out of reach of children when it is
energized or cooling down.
•
The steam generator must not be left unattended
while it is connected to the supply mains.
•
The steam generator must be used and rested on
a stable surface.
•
When placing the iron on the steam generator base
or on its heel, ensure that the surface on which the
heel or base is placed is stable.
•
The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
•
The filling aperture may be opened during use, due
to the design of the system.
•
Do not operate with a damaged steam/supply
cord or grommet, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 2
3
Health and safety .............................................................................
Electrical requirements ....................................................................
Steam generator overview / Features .............................................
Control panel overview ....................................................................
Temperature guide ...........................................................................
Location ............................................................................................
Before use .........................................................................................
Using the steam generator for steam ironing .................................
Steam boost button (certain models only) ......................................
Filling .................................................................................................
Features ............................................................................................
Maintenance .....................................................................................
Emptying and storing .......................................................................
Contact us ........................................................................................
Guarantee .........................................................................................
Contents
2
2
4
5
6
6
6
7 & 8
8
9
9
10
11
11
12
Personal safety
• CAUTION - HOT: Burns
can occur from touching
hot parts, hot water or
steam, or the iron rest
plate.
• WARNING: Never direct steam at
electrical components or fittings. If
in doubt about the suitability of
steam for cleaning an appliance,
contact the appliance
manufacturer for advice prior to
cleaning.
• WARNING: Never touch the plug or
cable with wet hands.
• WARNING: Nozzles and tools will
be hot after use. Allow to cool
before attempting to remove.
• WARNING: Do not
discharge the
steam towards
people or
animals.
Danger of
scalding.
• To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
• The plug should be removed from
the wall socket after use, before
cleaning, filling or changing the
accessories, or carrying out user
maintenance.
Location
• Do not use or keep this product
outside.
• Do not store the appliance near hot
surfaces eg. ovens or heating
appliances.
Mains cable
• WARNING: A damaged or severed
mains cable fitted with a plug
should never be connected to the
mains supply. It must be
destroyed, as a damaged cable
becomes hazardous if connected
to a power socket.
• Do not let the mains lead come into
contact with the hot soleplate of the
iron.
• Do not allow the mains lead to
become strained.
Product safety
• WARNING: Always test on an
inconspicuous area first. Never use
on materials that can not resist
high temperature, such as dralon,
natural fur etc.
• Never modify the appliance in any
way.
Other safety considerations
• Do not use any chemical
detergents, perfumes, alcohol or
descaler etc in water.
• Repairs to electrical appliances are
only to be undertaken by trained
personnel.
• Unprofessional repairs can be
dangerous for users.
• Use only genuine Morphy Richards
spare parts and accessories.
• The appliance must not be left
unattended while connected to the
supply mains.
• This appliance is intended for
domestic use only. Misuse or use
for commercial or any other
purpose will render the guarantee
invalid.
Electrical requirements
• Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
• If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
• WARNING: This appliance must be
earthed.
• Should the fuse in the mains plug
require changing, a 13 amp BS1362
fuse must be fitted.
STEAM
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 3
4
(1) Steam boost button
(certain models only)
(2) Iron handle
(3) Cable pivot
(4) Steam trigger
(5) Temperature dial
(6) Soleplate
(7) Temperature indicator light
(8) Iron heel
(9) Filling cap
(10) Water tank handle
(11) Water tank release button
(12) Detachable water tank
(13) Iron-to-base locking hook
(14) Iron-to-base locking button
(15) Iron release button
(16) Iron rest plate
(17) Iron rear docking hook
(18) Control panel (see below)
(19) Base unit
(20) Cord storage groove
(21) Cord clamp
Steam generator overview
4
5
6
1
12
20
21
2
3
10
11
18
19
7
8
13
14
15
1716
9
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 4
5
Control panel (18) overview
Descaling indicator light (22)
When the system requires cleaning, the descaling
indicator light (22) will illuminate.
On/Off button (28) and
Power indicator light
(23)
Connect to a mains outlet and press the On/Off
Button (28). The power indicator light (23) will
illuminate and the low steam level indicator light
(24) will flash. To turn off, press and hold the
On/Off button (28) for 3 seconds.
Steam level buttons (29/30)
Press the relevant button to either increase (29) or
decrease (30) the steam level. The steam level
selected will be displayed by illumination of the
relevant steam level indicator light: low (24),
medium (25) or high (26). See step 5 of ‘Using the
Steam Generator for steam ironing’ on page 8.
Low water level indicator light (27)
If the water level is too low, the low water level
indicator light (27) will illuminate. See ‘Filling’ on
page 9.
22
25
24
26
23
29
30
28
27
3231
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 5
6
Locate the steam generator horizontally on the
iron rest plate of your ironing board (if large
enough) or on a heat resistant stand at the same
height as your ironing board or below it. Always
ensure the steam generator is on a firm surface
when ironing.
WARNING: Do not use the product on a
surface which could be damaged by heat or
steam such as a worktop or a polished wood
surface.
If in doubt, contact Morphy Richards.
Remove any protective cover from the soleplate
(6) and the base unit, if any.
Unwind and straighten the power (32) and steam
supply cords (31).
Textiles and clothes carry ironing instructions. If
not, follow the temperature guide above, but test
the temperature by ironing the hem of the
garment or other discreet area first.
It is advised to begin with ‘cool’ fabrics (see
above) and work up to higher settings. An iron
heats up quicker than it cools down so you’ll save
time and electricity.
If you turn the temperature dial down from a hot
setting to a cooler setting, wait until the
temperature indicator light (7) goes out (indicating
the correct temperature has been reached) before
you continue ironing.
You can carry the appliance by the iron handle (2)
once the iron is locked to the base unit (19) (see
‘Storing the steam iron’ on page 11).
Location
Before use
Heat setting markings on the temperature dial of all Morphy Richards irons match those of the International
Textile Care Labelling Code
Temperature guide
Symbol
(120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
Control dial
positions
Do not iron
• •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen
Rayon, Rayon
mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(see step 5 of
‘Using the Steam
Generator for
steam ironing’ on
page 8)
No steam
(see ‘Dry ironing’
on page 9)
Low Medium / High High
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 6
7
Using the Steam Generator for steam ironing
Turn the temperature dial (5) to suit the garment
(see ‘Temperature guide’ on page 6). The
temperature indicator light (7) illuminates until
the temperature is reached. Begin ironing when
the temperature indicator light goes out. If you
turn the temperature dial down, wait until the
temperature indicator light illuminates and then
goes off again.
Plug the appliance into a mains outlet, you will
hear a beep. Press the On/Off button (28), it will
beep again and the power indicator light (23)
will illuminate and the low steam level indicator
light (24) will flash.
2
When steam ironing, remove the detachable
water tank (12), lift the filling cap (9), and fill with
water to the max fill line. Replace the water tank.
1
3
Unlock the iron from its storage position on top
of the base unit (19) by pressing and holding the
iron release button (15) (marked with a padlock
icon) - this enables you to rotate the tip of the
soleplate (6) (in a clockwise direction) out from
under the iron-to-base locking hook (13) and lift
the iron heel (8) away from the rear docking
hook (17).
WARNING: To avoid burning yourself if the
soleplate is still hot, never press down on the
iron-to-base locking button
(14)
to unlock the
iron.
During use, the iron may be rested on the iron
rest plate (16) with the soleplate tip on top of the
iron-to-base locking hook (13) and the heel
slotted on to the rear docking hook.
4
15
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 7
8
Steam boost button (certain models only)
The steam boost function is ideal for relaxing the
fibres of tougher fabrics (like jeans and linen) and
getting rid of those stubborn, hard to reach creases.
To produce a quick, powerful shot of steam during
ironing, simply press and release the steam boost
button (1).
NOTE: After using the steam boost function, your
steam generator iron will require up to 5 seconds to
reheat before it can produce a second boost of
steam. If you require a high level of constant steam,
choose the appropriate steam level and use the
steam trigger (4) as instructed above.
Do not combine the two steam functions. Using the two buttons together will interrupt the flow of
steam and may result in the constant steam cutting out completely. For optimum steam output, use
each steam function separately and as detailed above.
1
Using the Steam Generator for steam ironing (continued)
4
5
Press the relevant button to either increase (29)
or decrease (30) the steam level. The selected
steam level will be displayed by illumination of
the relevant steam level indicator light. The
steam level indicator light will stop flashing and
illuminate constantly when the selected steam
level is reached.
For a strong, continuous flow of steam during
ironing, press and hold the steam trigger (4) to
deliver steam through the soleplate.
WARNING: The steam supply cord
(31)
will
get hot during use.
When you have finished ironing, turn off the
appliance by pressing and holding the On/Off
power button (28) for three seconds. A beep will
be heard and the power indicator light (23) and
steam level indicator (24/25/26) will be
extinguished.
Disconnect the plug from the mains outlet.
6
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 8
9
IN HARD WATER AREAS, WE RECOMMEND
A MIX OF 50% TAP WATER AND 50%
DISTILLED OR DEMINERALISED WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
Re-filling during use
If the water level is too low, the low water level
indicator light (27) will illuminate, a beep will be
heard, and the unit will not produce steam. If this
happens, disconnect the water tank and refill
with water.
Dry ironing
To use your steam generator as a dry iron only,
follow steps 2, 3 and 4 of ‘Using the Steam
Generator for steam ironing’ on page 7. You do
not need to put water in the tank or select a
steam level. Press
either the steam boost button
(1)
(certain models only) or the steam trigger
(4)
at least once every 10 minutes, or the product
will automatically turn off.
Auto shut-off (certain models only)
If
either the steam boost button
(1)
(certain
models only) or the steam trigger
(4) goes
unused for 10 minutes, the product will
automatically turn off for safety and to save
energy, and a beep will be heard.
To restart, press the On/Off button (28) (see step
2 of ‘Using the Steam Generator for steam
ironing’ on page 7) and wait for the temperature
to rise again.
Steam function
During steaming, small amounts of water may be
ejected from the soleplate. This is normal and
can be avoided by using the steam for short
amou
nts of time and only when the iron is at the
correct temperature (the temperature indicator
light (7) on the iron goes out when ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit during ironing.
We recommend for first time ironing that you
iron over an old towel.
NOTE: The product may occasionally produce a
pumping sound during steam ironing. This is
normal and is caused by water being pumped
through the steam generator.
Vertical steam
Vertical steam is useful for removing creases
from hanging clothes, curtains, upholstery, etc.
Hold the iron between 1cm and 2cm away from
the item and press either the steam boost button
(1)
(certain models only) or the steam trigger
(4)
.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Features
Filling
4 1
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 9
10
Cleaning the boiler
When the boiler requires descaling, the descaling
indicator light (22) will illuminate. When this
happens, the boiler must be manually rinsed out
with clean water until all the scale is removed.
The indicator light will go out only after the scale
has been removed.
WARNING: Never remove the boiler screw (33)
when the steam generator is hot.
1
Unplug the appliance from the mains outlet and
leave to cool for two hours.
2
Remove the detachable water tank (12) and rest
the iron on its heel (8) on a firm surface next to a
sink.
3
Hold the base unit (19) firmly with both hands and
shake well.
4
Turn the base unit (19) upside-down and pull
back the boiler cap (34). Unscrew the boiler
screw (33) with the boiler key (35), which is
attached to the underside of the base unit. If the
screw is a bit too tight to undo, try using a large
screwdriver or a socket and wrench set for more
leverage.
5
Hold the base unit (19) over the sink, turn the unit
the correct way up to empty all water and loose
scale from the boiler into the sink.
6
Using clean water, refill and empty the boiler
repeatedly until all scale has been rinsed out.
Never pour any descaling solution or any other
chemicals into the boiler. This will damage the
product. Only use clean water.
7
Replace the boiler screw, ensuring it is tightened
fully. Replace the boiler cap, boiler key, water
tank and iron to the base unit.
WARNING: Ensure the boiler is COMPLETELY
EMPTY before replacing the boiler screw (33).
TIP: Tip the appliance from side to side while
gently shaking to help to empty all
the water out.
9
The descaling indicator light (22) will extinguish
the next time you use the product. Please wait for
up to one minute whilst it pumps water and
registers that the boiler has been cleaned.
If the descaling indicator light does not
extinguish, it is likely there is still some water
inside the boiler. Let the product cool down fully
and pour out all the water again.
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate (6),
set the iron at the MAX position and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
Maintenance
33
35
34
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 10
11
Allow the appliance to cool.
Remove the detachable water tank (12) by
squeezing the water tank release button (11). Lift
the filler cap (9), and empty the water tank. Once
the water tank is empty, re-attach it to the base
unit (19).
To store, pull the cord clamp (21) outwards. Wrap
the power cord (32) and iron steam supply cord (31)
around the base unit in the cord storage groove
(20). Secure the cord in place with the cord clamp.
Avoid kinking of cables, particularly where they
meet
the base unit.
IMPORTANT: Do not pull too tightly on the iron
steam supply cord or on the cable pivot (3)
when wrapping the power cord (32) and steam
supply cord (31) around the base unit (19).
Damage to cables caused by wrapping too
tightly will not be covered by the guarantee.
Storing the steam iron
Lock the iron into the storage position on top of
the steam generator main body by pushing the
soleplate down on the iron-to-base locking
button (14) whilst pushing the iron heel (8) onto
the rear docking hook (17). The iron should now
be at a slight diagonal on the iron rest plate. Pivot
the tip of the soleplate (6) under the iron-to-base
locking hook (13) until the spring-loaded iron-tobase locking button (14) springs up, securing the
iron in place.
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from. Please have the product name, model
number and serial number to hand when you call
to help us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk To Us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact us
Emptying and storing
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 11
RN332007 MUK Rev1 07/15
Your standard 1 year guarantee is extend ed for an
additional 12 months when you register the product within
28 days of purchase with Morphy Richards. If you do not
register the product with Morphy Richards within 28 days,
your product is guaranteed for 1 year. To validate your 2
year guarantee register with us online at
www.morphyrichards.co.uk
Or call our customer registration line
UK 0344 871 0242
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with
Morphy Richards individually.
Please note that the 2 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
for more information.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the followin g information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no.
Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting Model number and Serial number on the product,
or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions set out below (see Exclusions),
the faulty appliance will then be repaired or replaced as
appropriate and dispatched usually within 7 working days
of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item will be calculated from original purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
For example, water should be emptied after each use.
Morphy Richards shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, misuse , negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in transit.
2 The fault is caused by limescale build-up.
3 The cables are damaged due to wrapping too tightly or
excessive kinking.
4 The appliance has been used on a voltage supply other
than that stamped on the products.
5 Repairs have been attempted by persons other than our
service staff (or authorised dealer).
6 The appliance has been used for hire purposes or non
domestic use.
7 The appliance is second hand.
8 Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
• This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morph y Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserve s the right to change the specification of
its models at any time.
For electrical products sold wit hin the
Europea n Co mmunit y. At the end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Loc al Authority or retailer for
recycling advice in your country
Exclusions
Registering your 2 year
guarantee
Your 1 year guarantee
Disclaimer
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8AJ
IF YOU ARE HAVING A PROBLEM
WITH ONE OF OUR PRODUCTS,
CALL OUR HELPLINE:
UK: 0344 871 0944
EIRE: 1800 409 119
SPARES: 0344 873 0710
RN332007 MUK Rev1.qxp_IB 20/07/2015 13:42 Page 12
Loading...