RN305000 MUK Rev1
* Register at www.morphyrichards.co.uk/support
U
K and Ireland customers only
Please read and keep these instructions for future use
IMPORTANT: To prevent limescale damage we recommend a combination of 50%
tap water and 50% distilled, deionised or demineralised water. This is particularly
important if you live in a hard water area.
Never use battery topping up fluid or water containing any substances like starch,
sugar, fragrant additives or defrosted water from a refrigerator.
Failure to maintain your iron will invalidate your guarantee.
If you experience any problems with this iron, do not return to the store.
Please contact our help line who will be happy to help:
We do stock spare filler lids for this iron, so if you need a replacement please call
0344 873 0710.
UK: 0344 871 0944 IRE: 1800 409 119
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
Pressurised Steam Iron
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 1
2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•
WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved.
•
Children shall not play with the appliance.
•
Cleaning and user maintenance shall not be made
by children without supervision.
•
Keep the iron and its cord out of reach of children
less than 8 years of age at all times.
•
The iron must not be left unattended while it is
connected to the supply mains.
•
The plug must be removed from the socket before
filling the iron with water.
•
The iron must be used and rested on a stable
surface.
•
When placing the iron on its heel, ensure that the
surface on which the heel is placed is stable.
•
The iron is not to be used if it has been dropped, if
there are visible signs of damage or it is leaking.
•
The filling aperture must not be opened during use.
•
Do not operate with a damaged grommet, it must
be replaced by the manufacturer, its service agent
or similarly qualified person in order to avoid a
hazard.
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 2
3
•
CAUTION - HOT: Burns can occur from
touching hot parts.
•
W
ARNING: Do not discharge the steam
towards people or animals. Danger of
s
calding.
• WARNING: To avoid electric shock, do not
immerse appliance in water / liquid.
• WARNING: Misuse of the appliance could cause
p
ersonal injury.
Electrical requirements and mains cable
• C
heck that the voltage on the rating plate of your
a
ppliance corresponds with your house electricity
supply which must be A.C. (Alternating current).
• D
o not let the mains lead come into contact with the
hot soleplate of the iron.
• Should the fuse in the mains plug require changing,
a
13 amp BS1362 fuse must be fitted.
• W
ARNING: This appliance must be earthed.
PLEASE READ ALL INSTRUCTIONS AND KEEP
FOR REFERENCE
Important safety instructions ........................................................
Electrical requirements ..................................................................
Steam iron overview / Features .....................................................
Digital display overview ...................................................................
Temperature guide ..........................................................................
Before first use ................................................................................
Location ...........................................................................................
Usage tips ........................................................................................
Using the iron ..................................................................................
Features ...........................................................................................
Maintaining your iron ......................................................................
Troubleshooting ..............................................................................
Guarantee ........................................................................................
Contact us .......................................................................................
Contents
2
3
4
5
6
6
6
6
7 & 8
9
10
11
12
12
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 3
4
(1) On-off / temperature decrease button
(2) Temperature increase button
(3) Auto Steam button
(4) Water spray button
(5) Crease light button
(6) Power cord
(7) Controls
(8) Iron handle
(9) Cable pivot
(10) Digital display (see page 5)
(11) Steam trigger
(12) Filling cap
(13) Self clean button
(14) Iron heel
(15) Crease light
(16) Water spray nozzle
(17) Water tank
(18) Soleplate
Steam iron overview
10
12
15
16
6
13
93 4
5
1
2
8
11
17
18
7
14
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 4
5
Digital display (10) overview
Temperature setting indicators (19)
The temperature indicators correspond with the
International Textile Care Labelling Code as
shown on the labels of your garments (see
‘Temperature guide’ on page 6).
Steam level indicators (20/21/22)
The steam level is automatically adjusted to suit
the selected temperature setting. The steam
level indicators change when you select your
desired temperature level.
Self Clean indicator (23)
This indicator will illuminate when the system
requires cleaning.
Auto shut-off indicator (24)
This indicator illuminates if the appliance has
entered auto shut-off mode after not being
used or moved for 1 minute if sat horizontally,
or 8 minutes if stood upright on its heel.
20
High steam
level indicator
21
Medium steam
level indicator
22
Low steam
level indicator
1
9
Te mp e ra t ur e
setting indicators
23
Self clean
indicator
24
Auto shut-off
indicator
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 5
6
Remove all packaging and any protective cover from the soleplate (18), if any. Unwind and straighten the
power cord
(6).
We recommend for first time ironing that you iron over an old towel.
Stand the iron on its heel
(14) and locate it on the iron rest plate of your ironing board (if large enough) or
on a heat resistant stand at the same height as your ironing board or below it. Always ensure the iron is on
a firm surface when ironing.
WARNING: Do not use the product on a surface which could be damaged by heat or steam such as
a worktop or a polished wood surface.
If in doubt, contact Morphy Richards.
Unwind and straighten the power cord
(6).
Textiles and clothes carry ironing instructions. If not, follow the temperature guide above, but test the
temperature by ironing the hem of the garment or other discreet area first.
It is advised to begin with ‘cool’ fabrics (see above) and work up to higher settings. An iron heats up
quicker than it cools down so you’ll save time.
If you turn the temperature level down from a hot setting to a cooler setting, wait until the temperature
setting indicator
(19) stops flashing (indicating the correct temperature has been reached) before you
continue ironing.
Locati
on
Usage tips
Befo
re
fir
st
use
H
eat setting markings on the temperature dial of all Morphy Richards irons match those of the International
T
extile Care Labelling Code
Temperature guide
Symbol
(
120°C Max) Cool (160°C Max) Warm (210°C Max) Hot MAX setting
T
emperature level
settings
D
o not iron
• •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen
Rayon, Rayon
mixtures
Ironing Iron on wrong side,
if moisture
required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
Without steam
Steam level setting
(see step 5 of
‘Using the iron’
on page 8)
No steam
(see ‘Dry ironing’
on page 9)
Low Medium / High High
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 6
7
Using the iron
1) Filling the tank
Make sure the iron is not plugged in. Fill the water tank (11) via the filling hole (6) to the MAX graphic on
t
he side of the water tank, this shows the MAX level of water that the tank can hold and should be
checked whilst filling and the iron is tilted.
T
O PROLONG THE LIFE OF THIS IRON, WE RECOMMEND A MIX OF 50% TAP WATER AND 50%
D
ISTILLED, DEIONISED OR DEMINERALISED WATER, ESPECIALLY IN HARD WATER AREAS.
Never use battery topping up fluid or water containing any substances like starch, sugar, fragrant
a
dditives or defrosted water from a refrigerator.
NOTE: Please see point 2 of ‘Exclusions’ on page 12.
Re-filling during use
If the water level is too low, the unit will not produce steam. If this happens, open the filling cap (12) and
refill with water.
Plug the appliance into a mains outlet, a beep
will be heard. Press the on-off / temperature
decrease button
(1) to switch the product on.
The 1-dot temperature setting indicator (19) on
the digital display (10) will flash until the
temperature is reached, at which point the 1-dot
temperature setting indicator will remain
constant and two beeps will be heard.
If a different temperature is required to suit the
garment (see ‘Temperature guide’ on page 6),
you may adjust the temperature as follows:
press either the temperature increase (2) or
temperature decrease button (1) repeatedly
until the required temperature setting indicator
(19) is displayed.
2) Temperature Selection 3)
Dot 1 Dot 2 Dot 3 Max
The appropriate temperature setting indicator (19)
will flash until the desired temperature is reached,
at which point two beeps will be heard. Begin
ironing when the temperature indicator
illuminates constantly. If you turn the temperature
down, wait until the temperature indicator stops
flashing before continuing ironing.
4)
WARNING: Keep hands and body away from
the hot soleplate (18).
NOTE: The temperature setting will reset
between each use. When the iron is plugged in
it will require switching on and the required
temperature selecting.
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 7
8
To help remove stubborn creases, you may
use the water spray function. Aim the water
spray nozzle
(16) at the difficult area on the
garment and firmly press and hold the water
spray button (4).
Pressing the water spray once will dispense a
set amount of water.
11
The steam level is automatically adjusted to
suit the selected temperature setting. This is
denoted by the steam level indicators
(20/21/22) on the digital display (10), which
will change along with the temperature setting
indicators (19) when you select your desired
temperature level.
To activate the steam pump and have steam
constantly emitted from the soleplate (18)
during ironing, press the Auto Steam button
(3). The steam level indicator will flash
indicating that the pump is operating and
steam is being produced. To stop the pump
producing steam, press the Auto Steam
button again, the steam level indicator will
stop flashing and remain constantly
illuminated.
We recommend switching off the steam when
resting the iron on its heel. This is to slow the
water usage down and save time on refilling.
5) Auto Steam button 6) Steam boost
Using the iron (continued)
7) Water spray
When you have finished ironing, turn off the
appliance by pressing and holding the on-off /
temperature decrease button
(1) for two seconds.
Two beeps will be heard and all indicators on the
digital display (10) will switch off.
Disconnect the plug from the mains outlet.
8) Switching off
The steam boost function is ideal for relaxing the
fibres of tougher fabrics (like jeans and linen)
and getting rid of those stubborn, hard to reach
creases.
To produce an extra boost of steam during
ironing, press and hold the steam trigger (11).
NOTE: Steam cannot be produced on the 1-Dot
setting - this is highlighted by no steam level
indicators (20/21/22) being visible on the digital
display (10) whilst the 1-Dot setting is selected
.
NOTE: For optimum steam quality, do not
operate the shot more than three times in
succession
.
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 8
9
Features
C
rease light
T
o enable clearer vision in difficult to see areas,
p
ress the crease light button
(5)t
o switch on the
crease light
(15), press again to switch off.
Dry ironing
To use your iron as a dry iron only, follow steps 2,
3, and 4 of ‘Using the iron’ on page 7. Do not
press the Auto Steam button (3) to operate the
steam pump. You do not need to put water in the
water tank
(17).
Vertical steam
Vertical steam is useful for removing creases from
hanging clothes, curtains, upholstery, etc. Hold
the iron between 1cm and 2cm away from the
item and press the steam trigger
(11)
.
Hold the iron vertically and turn on the Auto
Steam function for a constant flow of steam.
Simply allow the steam to pass lightly over the
item of clothing in question to help the creases
soften away. To generate a powerful shot of steam
for stubborn creases, press the steam trigger. You
can also use vertical steaming to clean and
refresh the upholstery around your home.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
A
uto shut-off
If t
he iron is not moved or any buttons on the
c
ontrols
(7)a
re unused for 1 minute if sat
horizontally, or 8 minutes if stood upright on its
h
eel, the product will automatically turn off for
safety and to save energy. When this happens,
t
he auto shut-off indicator
(
24)will flash and beep
o
nce.
To restart, either move the iron or press any
buttons on the controls
(7) and wait for the
temperature to rise again.
NOTE: The appliance is not turned off completely
in auto shut-off mode. To switch the product off,
press and hold the on-off / temperature decrease
button
(1)
until all indicators in the digital display
(10)
extinguish, then unplug the product from the
mains outlet.
11
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 9
10
Emptying and storing
W
hen you have finished ironing, press and hold
the on-off / temperature decrease button
(1) to
s
witch the product off, then unplug and empty
a
ll water from your iron. When cool, store the
iron on its heel
(14)
with the power cord
(6)
w
rapped loosely around the heel.
NOTE: Please see point 3 of ‘Exclusions’ on page
12
.
Cleaning the soleplate
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate (18),
set the iron at the MAX setting and pass it over a
clean piece of cotton to draw the deposit off the
surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
Removing limescale
Y
our iron has a built in self clean system
designed to keep the water valve, steam
chamber and steam vents clear of lint and
loose mineral deposits.
When the self clean icon (23) appears on the
digital display (10), the self clean function must
be operated.
1 H
alf fill the iron with water.
2 C
onnect to a mains supply outlet.
3 Set the temperature to the MAX setting. Wait for
the temperature to be reached - the temperature
s
etting indicator(19)with illuminate constantly.
4 P
ress and hold the on-off / temperature
decrease button (1) to switch the product off
.
5 Disconnect the iron from the mains supply outlet.
6 W
hilst the iron is still very hot, hold the iron
horizontally over a sink.
CAUTION: The soleplate will still be hot, so
ensure the power cord and plug are kept away
from it and the sink.
7 Press and hold the self-clean button
(13)
.
WARNING: Steam and boiling hot water will
drain from the holes in the soleplate. Keep
hands and body away from the hot water. This
washes away the scale and minerals that have
built up inside the steam chamber.
8
Whilst still holding the self-clean button, gently
move the iron back and forth until the water tank
is empty.
9
When steam and hot water ceases to be
released from the soleplate, release the
self-clean button.
10
When the process is complete, re-connect to a
mains supply outlet, switch on and allow to heat
up - this will dry the soleplate.
11 Disconnect the iron from the mains supply outlet.
12
Rest your steam iron on its heel
(14)
and allow to
fully cool down.
13
Wipe the soleplate with a cold, damp cloth.
After this cleaning operation, empty out any
remaining water.
IMPORTANT: Do not attempt to descale the
soleplate with descaling products.
Maintaining your iron
23
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 10
11
Troubleshooting
• N
o power or not heating up.
• Overheating or not getting
hot enough.
• Not steaming or poor steam.
• Dripping from the holes in
the soleplate.
• Tripping Electrics.
• The filler cap is broken or
does not close properly.
Problem Solution
• Steam is triggered when I
press the water spray button.
1.C
heck the fuse and the fuse rating (should be 13amp).
2.T
ry a different appliance in the socket as it may be the socket that
is at fault.
3.C
heck that the auto shut off has not operated.
4. Ensure the iron is switched on by pressing the on-off /
t
emperature decrease button (1)
.
1. Adjust the temperature to ensure the setting matches that
recommended on the garment or refer to the “temperature guide”
section.
2. Allow the iron to reach temperature and stabilise for 1-2 minutes if
it has just been plugged in, or has just been woken up from auto
shut off.
1. Ensure the temperature is set within the steam band and that the
steam level is set to the correct level (refer to the “temperature
guide” section).
2. Check that there is enough water in the tank.
3. If the auto shut off feature has activated, wake up the iron and
allow it to reach temperature before using steam.
4. Perform a self-clean to clear away limescale inside the iron (refer
to “Removing limescale” section).
5. Please remember the iron does not steam on the 1-dot setting.
1. Use the steam for short amounts of time.
2. Perform a self-clean to clear away limescale inside the iron (refer
to “Removing limescale” section).
3. If the auto shut off feature has activated, wake up the iron and
allow it to reach temperature before using steam.
1. Try using a different socket.
2. Ensure there are no other appliances being used on the same set
of sockets as the iron.
1. Call our helpline to order a new replacement filler cap to be sent
out.
2. Please note, there may appear to be a gap between the digital
screen and filler cap, as long as the cap clicks shut, water should
not leak out.
1. This is normal, a small amount of steam may appear when
pressing the water spray button.
• The product occasionally
produces a pumping sound
during steam ironing.
1. This is normal and is caused by water being pumped through the
steam pump.
2. If the pumping sound suddenly becomes louder or the steam
diminishes, check and refill the water tank if it has become empty.
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 11
RN305000 MUK Rev1 10/17
Your standard 1 year guarante e is extended for an
additional 2 years when you register the product within 28
days of purchase with Morphy Richards. If you do not
r
egister the product with Morphy Richards within 28 days,
y
our product is guaranteed for 1 year. To validate your 3
year guarantee, register with us online at
www.morphyrichards.co.uk/support
Or call our customer registration line
UK 0344 871 0242
I
RE 1800 409 119
N.B. Each qualifying product needs to be registered with
M
orphy Richards individually.
Please note that the 3 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
for more information.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
Model no. Serial no.
All Morphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting Model number and Serial number on the product,
or write to Morphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subjec t to the exclusions (see Exclusions ), the faulty
appliance will then be repaired or replaced as appropriate
and dispatched usually within 7 working days of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item wi ll be calculated fro m original purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
Morphy Richards shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1 The fault has been caused or is attributable to accidental
use, m isuse, negligent u se or used cont rary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in
transit.
2 The fault is caused by limescale build-up.
3 The cables are damaged due to wrapping too tightly or
excessive kinking.
4 T
he appliance has been used on a voltage supply other
than that stamped on the products.
5 R
epairs have been attempted by persons other than our
s
ervice staff (or authorised dealer).
6 T
he appliance has been used for hire purposes or non
d
omestic use.
7 T
he appliance is second hand.
8 Morphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
• This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. Morphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
Morphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserve s the right to change the speci fication of
its models at any time.
For electrical products sold wit hin the
Europea n Community. At the end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer for
recycling advice in your country
Exclusions
Your 1 year guarantee
Disclaimer
Registering your guarantee
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from. Please have the product name, model
number and serial number to hand when you call
to help us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk to us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Address:
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8AJ
Contact us
RN305000 MUK Rev1.qxp_IB 17/10/2017 12:10 Page 12
Loading...