Morgana DigiBook 300r2 Operator's Manual
Operator Manual
DigiBook 300r2
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rel. 03.00
Operator Manual Digibook 300
Summary
1 INTRODUCTION __________________________________________________ 5
1.1 SYMBOLS OF SAFETY _______________________________________________________________ 7
1.2 SYMBOLS OF PROHIBITION AND OBLIGATORINESS _______________________________________ 8
1.3 THE SAFETY DURING THE USE OF THE MACHINE _________________________________________ 9
1.3.1 general ________________________________________________________________________ 9
1.3.2 SAFETY WARNINGS ______________________________________________________________ 9
1.4 SAFETY CLOTHING _______________________________________________________________ 10
1.5 INSTALLATION OF ELECTRICAL CABLES AND PIPES ______________________________________ 11
1.6 SAFETY EQUIPMENTS IN THE PERFECT BINDER _________________________________________ 11
1.6.1 Emergency button ______________________________________________________________ 11
1.6.2 Green button for start cycle ____________________________________________________ 12
1.6.3 SAFETY light curtains ___________________________________________________________ 12
1.6.4 Protection plate of the milling station ____________________________________________ 13
1.6.5 MAIN SWITCH __________________________________________________________________ 13
1.7 RISKS __________________________________________________________________________ 14
1.8 PURPOSE _______________________________________________________________________ 15
1.8.1 uses not provided, uses prohibited _______________________________________________ 15
2 TECHNICAL SHEET MASTERBOOK300 ________________________________ 16
2.1.1 Electrical _____________________________________________________________________ 18
2.1.2 Pneumatics ____________________________________________________________________ 18
Air quality provided to the Perfect Binder _______________________________________________ 19
DIN ISO 8573-1 – air quality class ________________________________________________________ 19
3 ACCESSORIES __________________________________________________ 20
4 TRANSPORTATION ______________________________________________ 21
5 STORAGE _____________________________________________________ 23
6 LAYOUT ______________________________________________________ 24
7 POSITIONING AND WORKSPACES ____________________________________ 24
8 INSTALLATION _________________________________________________ 26
8.1 TECHNICAL STAFF FOR THE INSTALLATION ___________________________________________ 26
8.2 PHYSICAL CHARACTERISTICS OF THE AREA OF PLACEMENT ______________________________ 26
8.3 SUPPORT SURFACE _______________________________________________________________ 26
8.4 WEATHER PROTECTION ___________________________________________________________ 26
8.5 LIGHT _________________________________________________________________________ 27
8.6 ENVIRONMENTAL CONDITIONS ______________________________________________________ 27
8.7 ELECTRICAL CONNECTION _________________________________________________________ 28
8.7.1 Ground connection _____________________________________________________________ 28
2
rev. 3.00
Operator Manual Digibook 300
9 TRAINING OF THE OPERATOR ______________________________________ 29
10 POWER ON ____________________________________________________ 30
10.1 FUNDAMENTALS ____________________________________________________________________ 31
10.2 ELECTRICAL CONNECTION _____________________________________________________________ 33
10.3 PNEUMATIC CONNECTION _____________________________________________________________ 33
10.4 DESCRIPTION OF THE GROUPS __________________________________________________________ 34
10.5 CHIPS ASPIRATOR ___________________________________________________________________ 37
10.7 PUR TANK OPENING AND CLOSING, AND GLUE LOADING. _________________________________________ 39
10.7.1 Opening of the PUR tank ________________________________________________________ 39
WARNINGS ON THE OPENESS OF PUR TANK ________________________________________________ 39
10.7.2 preparation and loading of the pur glue __________________________________________ 41
10.7.3 Cleaner loading ________________________________________________________________ 43
11 FUNCTIONS OF THE PERFECT BINDER ________________________________ 45
11.1 HOME PAGE ________________________________________________ ERROR! BOOKMARK NOT DEFINED.
11.2 HOME PAGE ________________________________________________ ERROR! BOOKMARK NOT DEFINED.
11.3 NAVIGATION MENU OF THE PARAMETER PAGES ________________________ ERROR! BOOKMARK NOT DEFINED.
11.4 FAST CONFIGURATION OF THE BOOK _______________________________ ERROR! BOOKMARK NOT DEFINED.
11.4.1 Navigation Through the menus _____________________________ Error! Bookmark not defined.
11.4.2 Page to display production meters _________________________ Error! Bookmark not defined.
12 PAGE FOR TIMER MANAGEMENT ____________ ERROR! BOOKMARK NOT DEFINED.
13 PAGES OF ALARMS ______________________ ERROR! BOOKMARK NOT DEFINED.
14 PARAMETERIZATION OF EACH GROUP _______________________________ 51
14.1 PARAMETER OF CLAMP / FEEDER _________________________________ ERROR! BOOKMARK NOT DEFINED.
14.2 PARAMETER OF THE MILLING STATION ______________________________ ERROR! BOOKMARK NOT DEFINED.
14.3 PARAMETER OF THE GLUE HEAD __________________________________ ERROR! BOOKMARK NOT DEFINED.
14.4 TEMPERATURE OF THE HEAD AND THE PRE-MELTING UNIT ________________ ERROR! BOOKMARK NOT DEFINED.
14.4.1 Head glue processing information __________________________ Error! Bookmark not defined.
14.5 PARAMETER OF THE PRESS _____________________________________ ERROR! BOOKMARK NOT DEFINED.
14.6 PARAMETER OF THE COVER _____________________________________ ERROR! BOOKMARK NOT DEFINED.
15 ACCESS TO THE PAGES OF THE MANUAL HANDLINGERROR! BOOKMARK NOT DEFINED.
15.1 MANUAL MOVEMENTS OF THE CLAMP _______________________________ ERROR! BOOKMARK NOT DEFINED.
MANUAL MOVEMENTS OF THE FEEDER ___________________________________ ERROR! BOOKMARK NOT DEFINED.
15.2 MANUAL MOVEMENTS OF THE MILLING STATION _______________________ ERROR! BOOKMARK NOT DEFINED.
15.3 MANUAL MOVEMENTS OF THE GLUE HEAD ___________________________ ERROR! BOOKMARK NOT DEFINED.
15.4 MANUAL MOVEMENTS OF THE PRESS _______________________________ ERROR! BOOKMARK NOT DEFINED.
15.5 MANUAL MOVEMENT OF THE COVER _______________________________ ERROR! BOOKMARK NOT DEFINED.
16 OPERATION OF THE SYSTEM IN STANDBY _____ ERROR! BOOKMARK NOT DEFINED.
17 CLEANING USING CLEANER AND LOADING GLUE ERROR! BOOKMARK NOT DEFINED.
18 PAGE OF JOB MANAGEMENT _______________ ERROR! BOOKMARK NOT DEFINED.
3
rev. 3.00
Operator Manual Digibook 300
18.1 PAGE OF JOB MANAGEMENT _____________________________________ ERROR! BOOKMARK NOT DEFINED.
19 GLUE RECOVERY PROCEDURE ______________________________________ 64
20 COVER POSITIONING _____________________________________________ 67
PREPARATION OF THE MACHINE TO PRODUCE A BOOK. _____________________ 69
21 CLEANING THE MACHINE _________________________________________ 72
21.1 PROCEDURE TO CLEAN THE SPINE GLUE EXTRUDER. ____________________________________________ 73
21.2 PROCEDURE TO CLEAN THE GLUE SIDE EXTRUDERS. ____________________________________________ 75
21.3 “END OF JOB” CLEANING _____________________________________________________________ 78
21.4 DETAILS CLEANING _________________________________________________________________ 80
22 PROBLEMS - SOLUTIONS __________________________________________ 83
22.1 CHIPS ASPIRATOR – LESS VACUUM: ___________________________________________________ 83
22.2 CLAMP – IT DOES’T START: ____________________________________________________________ 83
22.3 IRREGULAR GLUE START / STOP : ___________________________________________________ 83
22.4 MILLING STATION – IRREGULAR CUT AND NOTCHING: _______________________________________ 83
22.5 COVER PLATE MILLING STATION – IT DOES’T OPEN / CLOSE CORRECTLY: _________________________ 83
22.6 HEAD - OUT OF TOO MUCH OR LITTLE GLUE: ___________________________________________ 83
22.7 PRESS ________________________________________________________________________ 84
4
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
THE READING OF THIS OPERATOR AND MAINTENANCE MANUAL IS FUNDAMENTAL FOR THE SAFETY
OF THE USER AND FOR THE PROPER USE OF THE
EQUIPMENT.
1 INTRODUCTION
We thank you to have bought our product. This machine has been designed specifically
for your job and your applications, and provides a high quality production and a wide
range of functions.
This manual describes how to use the machine, starting from the configuration phase to
the most important operations. This manual has been written in order to be easily understood also by user not trained about the use of this kind of machine. For the best use
of the equipment, please read carefully this manual before to use the machine. After
reading, we suggest saving the manual in a safety place and don’t hesitate to read him
when necessary.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
5
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
DECLARATION THAT THE MACHINE IS IN SPECIFICATION TO THE EEC
DIRECTIVE CONTROLLING THE MACHINES 2006/42/CE,
(AND FOLLOWING EEC DIRECTIVES)
We declare that the production of:
Product: Perfect Binder
Model/Type: Digibook 300
Serial Number: MB300-....
Year of construction: 2012
Follows the actual releases of the EEC Controlling Directives:
EEC Directive 2006/42/CE;
EMC Directive 89/336/CEE;
Directive controlling the Low Voltage 2006/95/CEE
And in particular the following Directives:
EN 1010
EN 60 204-1
EN 61 000-6-2, EN 61 000-6-3, EN 61 000-6-4
Assago , (MI) Italy
__/__/2012
6
K.G.S. S.R.L.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Attention – General danger!
Attention – Electrical voltage!
Risk of electric shock.
Attention – Sharp blades!
Risk of cut.
Attention – Hot surfaces!
Risk of burn.
Attention – Risk of rolling parts!
Risk of crushing.
Attention – Risk of moving chain!
Risk of crushing.
SAFETY
1.1 SYMBOLS OF SAFETY
In the manual some symbols are used to inform about dangerous situations for people
and/or things.
The following symbols mean dangerous situations for people and/or things.
If you don’t follow carefully the appropriate procedures, damages can occur to people
and/or things and in extreme situations also fatal accidents. Together with the symbols
it is written also what to do.
7
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
In case of not warning of the symbols damages, also great, can happen to the machine and to the accessories.
This symbol means a prohibition.
This symbol means an imperative.
This symbol means that it is mandatory to read in this manual information regarding specific topics (for ex. related to the specifications
of the electric and pneumatic connection).
1.2 SYMBOLS OF PROHIBITION AND OBLIGATORINESS
MyBinding.com
5500 NE Moore Court
8
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
It is forbidden to use the machine when occurs one of the following situations:
in explosive environment;
in flammable atmosphere;
in excessive durst environments.
Danger!
Failure to comply with some or all the instructions listed in this manual
could cause damage to the machine and / or personal injury. The manufacturer is not responsible for an arbitrary and improper use of the machine such as:
Using the machine by untrained personnel;
Use contrary to law;
Incorrect installation;
Defects in electrical power and / or pneumatic;
Partial or total failure to comply with the instructions;
Lack of maintenance and / or use of aftermarket parts;
Changes or other actions not authorized by the manufacturer;
1.3 THE SAFETY DURING THE USE OF THE MACHINE
1.3.1 GENERAL
The manufacturer guarantees that the contents of this manual are in specification with
the procedures required by the machine. The manufacturer therefore will be not responsible if the machine will be used in a different way.
1.3.2 SAFETY WARNINGS
Before the use of the machine, please read carefully the manual.
Save the manual for further needs.
By apply different procedures, and not the specific procedures described in the manual,
can produce operational problems.
Please, read carefully the following Safety rules.
9
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Eye protection against any spray of PUR glue or high temperature
cleaner
Respiratory Mask
Protective gloves
The safety clothing IS NOT INCLUDED in the machine and must be
procured by the machine user.
The operator should wear clothing appropriate to the situation
and specially during the following operations:
-Maintenance
-Replacing of the PUR glue
-Cleaning of the PUR system
a) Eye protection against any spray of PUR glue or high temperature cleaner
b) Respiratory Mask
c) Protective gloves for high temperature
1.4 SAFETY CLOTHING
Clothing to use during the cleaning and /or maintenance operations
Tight clothing, to avoid that they remain engaged with protruding parts.
Long hair must be covered or otherwise collected by using e. g. a protective screen.
Do not wear watches or jewels.
Safety clothing
10
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
DANGER! It is forbidden to remove or render ineffective the safety
guards for the safety of persons, and to tamper and / or modify, even
partially, safety devices installed on the machine. In case of alarm signals due to the intervention of the safety, the operator must request the
immediate intervention of technical people trained on the maintenance.
The manufacturer is not responsible of any damage to persons or animals
caused by tampering with the guards."
In the diagrams the emergency button is
identified 15S1
.
Activation state of emergency: the push-
button must be pressed
OFF state emergency stop: the button
must be turned clockwise"
1.5 INSTALLATION OF ELECTRICAL CABLES AND PIPES
Cables and pipes must be put inside of special cable channels to avoid the people to
stumble and get hurt.
1.6 SAFETY EQUIPMENTS IN THE PERFECT BINDER
1.6.1 EMERGENCY BUTTON
It is located on the front, easily accessible from the operator's position.
.
11
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
The green button executes the command
to start cycle, it means that the clamp
closes and moves to the right, the mill if
activated will run the cut, the glue will
be applied, and if the press has been activated will crush the book; all this happens if I put the book block in the clamp
and place a cover on the press.
Detail: SAFETY curtain
In the diagrams the SAFETY curtains are identified in the following way:
Left SAFETY curtain 15SS2, right SAFETY curtain 15SS1
1.6.2 GREEN BUTTON FOR START CYCLE
1.6.3 SAFETY LIGHT CURTAINS
Two safety light curtains are placed at the ends of the binder.
In case of occupation of the work place during the production cycle, the machine stops
instantly in a state of emergency, preventing and avoiding of shocking or crushing objects or hands or arms of the operator.
12
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
The plate consists of a mobile plate that, except when the book block is moving, covers
the cutter in all operating conditions, even at
a standstill.
An elastic cord exerts constantly on the
plate (F) a force (see arrows) that covers
the mill disc. A sensor monitors and the
cutter stops if the guard is opened, the
motor of the cutter is also equipped with
a brake."
Position OFF
The switch is
open. The machine is off.
Position ON
The switch is
closed.
The machine is
on.
1.6.4 PROTECTION PLATE OF THE MILLING STATION
1.6.5 MAIN SWITCH
It is located on the left side of the machine.
13
rev. 3.00
Operator Manual Digibook 300
Area of the glue head.
Attention – Hot surfaces!
Risk of burn.
Use protective gloves.
Area of glue loading.
Attention – Hot surfaces!
Risk of burn.
Use protective gloves.
Area of the mill.
The disc contains several
types of milling cutters. Use
protective gloves, in case of
removing the Notching
Roughening or the brush.
1.7 RISKS
There are risks that cannot be completely eliminated by either protective or as designed
by the machine.
14
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Any other use such as,
- Milling / Roughening of book spines already binder ( Adhesive binder, stitching book, Sewing Book, etc.)
- Use of materials other than those specified in a) and b)
- Operations beyond the technical specifications are not to
be regarded as intended use.
1.8 PURPOSE
The machine is used to bind books using the following materials:
a) Signatures, or sheet of paper (printed or not) for the block book
b) Cardboard as cover of the book
Within the limits specified in the data sheet, included in this manual.
1.8.1 USES NOT PROVIDED, USES PROHIBITED
The user has the total responsibility of the damages to people or things due to an improper use, outside of their intended use.
MyBinding.com
15
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
2 TECHNICAL SHEET Digibook 300
Machine features:
Cycle/Hour 300 mechanical cycles
Spine length 100 – 450 mm
Workable height of the book 120 – 320 mm
Max. Cover size 710x460/240x110 mm
Workable thickness of the book 2 – 50 mm
Max. Cover Weight 500 g/m2
Control Screen
Touch - Screen Yes
Copy Counter Yes
Memory of the jobs Yes
Diagnostic and Check Yes
Setting size, temperature control Yes
Speed Yes
Book Loading
Adjustment of the clamp Automatic, following the parameters introduced by the
user
Clamp opening Automatic, electrically driven
Clamp closing Adjustable air
Spine preparation
Milling disks Ø 160 mm
Notching 2
Roughening for spine processing 4
Brush for spine processing and cleaning 1
Excludable mill Mechanical (with position control)
Milling thickness 0 - 2.3 mm
Chips aspirator Included in the machine
Glue application system
Tank PUR/Hot-Melt glue 3 Kg sealed
Extrusion system of PUR/Hot-melt Integrated and sealed
Extrusion head adjustment Automatic
Side adjustment (used for signatures or wire stapling) Mechanical (high accuracy)
Glue Stop Adjustable by Touch-Screen
Cleaning / sealing Yes
Press:
Press Electro-pneumatic servo-controlled
Adjustment Force / pressure, pressing time
16
rev. 3.00
Operator Manual Digibook 300
Mechanical Adjustment Automatic/mechanical height adjustment
Mechanical Adjustment
Cover back bar adjustment Automatic, driven by the parameters on the
Touch-Screen Cover loading Hand made by the operator
Dimensions / Weight
Length 1850 mm
Width 1090 mm
Height 1370 mm
Weight 500 Kg
17
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Power of the machine
Protection fuses on the power network are duties of the customer
Distribution cabinet, customer side
16 A
Differential protection class A 300mA
Supply pressure
The pneumatic system of the user must ensure, in the inlet connection of the compressed air in
the perfect binder, the following values:
Min.: 7 bar
air consumption: 200 l/h
air quality: Class 3
Pneumatic Characteristics of the machine
Compressed air consumption
200 l/h
Calibration of input gauge
6 bar
Min. working pressure
5.5 bar. If the pressure value falls below this value the machine enter in an “alarm” condition
Diameter of air inlet
10mm
The 10 mm diameter pipe for the connection to the compressor is not provided together with the
machine.
It is suggested the use of a compressor equipped with the automatic condensate drain, to
avoid verify weekly if there is some water inside the compressor.
It is suggested to use a silenced compressor, if the compressor is located inside the working
plant.
2.1.1 ELECTRICAL
Electrical power 400 V ±5%, 50 Hz, 3 ph + N + PE
2.1.2 PNEUMATICS
18
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Air quality provided to the Perfect Binder
CLASS 3, DIN ISO 8573-1
Durst: 5 micron - 5 mg/m3
Water: -20°C - 0,88 g/m3
Oil: 1 mg/m3
The compressed air system upstream of the machine must be equipped with
a dryer.
Periodically check the quality of the compressed air supplied to the machine
and the operating values .
AIR QUALITY PROVIDED TO THE PERFECT BINDER
To make work the pneumatic devices in an affordable, efficient and safe way, the compressed air supplied to the pneumatic device must have the following quality features:
Pressure, Quantity, Water content, solids content, oil content.
DIN ISO 8573-1 – AIR QUALITY CLASS
The manufacturers of pneumatic components refer to the quality of compressed air to
use on their products, referring to the table below.
The compressed air used in the industry contains water, oil, dust and other impurities.
The interaction of these elements produces an aggressive mixture that can damage the
compressed air devices and also the PUR glue contained in the PUR tank, the results will
be a low quality production and increased maintenance costs.
19
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Polizene green spatula (to remove excess
glue or cleaner)
Steel Wire 0.4" (for cleaning the channels
of leakage of the lateral glue)
Lamella thickness of 0.4 (for cleaning the
slit of leakage of the spine glue)
Spare Headless screws for the closure of
the ducts
Protective gloves
Set of L wrenches
One pack of 2 kg of PUR Glue Henkel
One pack of 2 liters of beans CleanerBlue Henkel
3 ACCESSORIES
The standard composition includes:
– Cleaning Kit
– Start- up Kit
CLEANING KIT
START-UP KIT
20
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
The Perfect Binder must be handled by a
heaver.
It can be got on all 4 sides, at the bottom
of the frame are provided channels for
the insertion of the forks.
For the final positioning or small movements can be used a trans-pallet.
The machine can be raised by trans-pallet
only in the 2 long sides, front and rear."
The image shows the location and size of the channels for the brackets for the transpallet and the forklift.
4 TRANSPORTATION
21
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
DANGER! For no reason the staff is authorized to pass under a suspended
load during transport or in the proximity of. The producer is not responsible for what happens during this operation, to be carried out by qualified and authorized personnel, with the necessary individual safety protections (Suit, shoes, gloves, helmet, and glasses).
Attention! The machine is balanced. In any case keep the forks low.
In case of unbalance use weights. It is forbidden to hold by the hands the
projecting parts. The machine and its parts must be protected from the
weather outside. In particular, water, dust and moisture can oxidize certain elements of the machine, damaging them irreversibly. Follow the
usual precautions to avoid falls and bumps.
IMPORTANT
a) We do not provide tools for docking and lifting.
b) The disposal of packaging materials will be provided by the recipient and must be
conducted in accordance with the local regulations.
c) Remove dust and dirt accumulated during the transportation.
MyBinding.com
5500 NE Moore Court
22
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Conditions of transportation and storage
Temperature average
-5/+55°C
Humidity average
30/90%
Lighting
Adequate natural and / or artificial
Weather
Adequate weather protection
Space required
Adequate to allow the operations of
lifting and carrying in SAFETY.
Horizontal ground plane
Horizontal ground plane must have a
capacity in excess of the total mass of
the machine.
In the case of removal or unused for long
periods (over 30 days), it is necessary to
drain the glue system and to put inside
the protection cleaner.
The damage caused by this failure
will void the warranty of the glue device.
During periods of downtime you should
not open the tank containing the glue;
otherwise it accelerates the deterioration
creating serious permanent damage to the
glue device.
The damage caused by this failure
will void the warranty of the glue device.
Protect with anti-corrosive products the
parts subject to wear and work plans. Ref.
to the section “maintenance”.
Do not climb or place any objects on top of
the machine
5 STORAGE
The information contained in this section must be observed in case of temporary storage
of the machine that may occur in the following situations:
Installation of the machine not immediately after its delivery.
Uninstalling the machine.
Storage awaiting a new location.
The machine must be stored and transported under conditions of SAFETY as shown in the
table below.
23
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
6 LAYOUT
7 POSITIONING AND WORKSPACES
Positioning:
The Perfect Binder must be positioned so as to have a clear space around of at least 80
cm, and around the work area at least 150 cm.
The room where the machine is installed must be properly ventilated with air change.
24
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
Glue loading area
Glue loading area, the operator enter in this area to load the
glue in the machine.
Access area for the maintenance, for access to the electrical
and pneumatic panel.
Transit area
Used to transit from the work area to the glue loading area.
Operator’s work area
Operator’s work area during the normal use of the machine.
Right side of the machine
It is not necessary to leave a space available.
Workspaces
MyBinding.com
5500 NE Moore Court
25
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Operator Manual Digibook 300
8 INSTALLATION
8.1 TECHNICAL STAFF FOR THE INSTALLATION
The machine must be installed by people specifically trained and authorized by K.G.S. .
8.2 PHYSICAL CHARACTERISTICS OF THE AREA OF PLACEMENT
In addition to the overall dimensions of the machine given in the previous chapter, you
must also meet the following conditions:
Near the area of placement of the machine should be arranged the sources of electric
power and pneumatic following what is written in this manual.
Provide sufficient space for normal use, maintenance of machinery, for any command
and for additional equipments to connect. Refer to the draft in the chapter of the positioning.
The chosen site should not be close to deposits of flammable materials, or to operational sites that may create flammable or explosive atmospheres.
For the installation you must choose an operational area depending on the size of the
machine parts and lifting equipment selected, pay attention to the presence of any obstacles on the road (equipments, walls, etc.).
8.3 SUPPORT SURFACE
The machine requires no special foundations. It must be ensured the availability of an
industrial floor.
The producer has no responsibility about the enforcement of foundations (resistance
calculation, thick reinforced concrete, etc.), which are under responsibility of the customer or company performing the design and construction of the foundations themselves.
The Perfect Binder rests on four feet of 100 mm diameter.
8.4 WEATHER PROTECTION
The machine must be placed in a covered room, protected from direct contact with atmospheric agents.
26
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
rev. 3.00
Loading...