Morel SoundWall IN-5H, SoundWall IN-8H, SoundWall IN-6H, SoundWall IN-6Hf, SoundWall IN-8M User Manual And Installation Manual
...Page 1
User manual and installation guide
SoundWallTM Series
Page 2
Dear Customer,
Thank you for choosing Morel's SoundWall
TM
in-wall speaker!
These handcrafted speakers are uniquely designed and constructed, to offer extraordinary sound quality for both stereo
and home theatre applications. When properly installed the SoundWallTM speakers will transform your musical and
cinematic experiences into true magic for your long lasting enjoyment.
The information in this manual will help you get the best possible performance out of your speakers. If you have any
questions, please contact your Morel dealer, or Morel Support at www.morelhifi.com.
Introduction
Speaker placement
The position of the speakers has a great effect on the quality of the sound and soundstage created. Here are some
recommended guidelines that will assist you in the speaker placement process.
The Morel SoundWallTM speakers are designed to work well in both small and large rooms.
Regardless of the application you may require it is recommended to make sure there are no objects that may block
the area between the listener and the speakers.
Before installing the speakers consider the proximity to the electricity and other fixtures.
Recommended speaker placement for stereo application
Installation preparation
Insulating the Wall Cavity
To achieve the very best from your loudspeakers we recommend you fill the wall cavity behind the speakers with
fibre-glass insulation / Rockwall. It is important to try and keep the same amount of insulation material for each
speaker to receive a true consistent bass response.
Install insulation also in the bays adjacent to the speaker location to reduce the noise produced by unsupported
drywall. If in doubt, please consult your dealer / installer.
Back Box
Morel's SoundWallTM speakers infinite baffle design allows you to place them in the wall cavity without the need
for an enclosure. Nonetheless, in order to
reduce sound transmission to other rooms it is recommended to use a
back box / enclosure.
Here are Morel's recommended ideal enclosure sizes for the SoundWallTM series:
Recommended speaker placement for home theatre
Place the speaker on either
sides of the flat panel
screen
1
The speaker should be centered to
the flat panel screen
2
Ideally:
x x
x
x
x
The listener
2
Min.
50mm
Flat panel screen
2
4
3
*
If additional speakers are desired - they should be placed at the same height as the main frontal
speakers (if positioned on the side walls)
Aim to set the speaker as close as possible
to this diagram for optimal performance
The tweeter should be at ear level
The distance between the speakers is
2
/3
the distance from the listener
3
2
1
Preferably place the centre speaker
under the flat panel screen
4
The distance between the
edge of the flat panel screen
and the speaker should be
minimum 50mm
3
H5", M5" & X5" 9 liters (0.317 cubic feet)
H6", M6" & X6" 13 liters (0.459 cubic feet)
H8" & M8" 24 liters (0.847 cubic feet)
Page 3
7
8
Connect speaker to the frame with original
supplied screws
Align speaker to frame
Marking the wall bracket location using the cardboard
template(make sure there is no stud at the back of the
drywall)
2
1
Cut the wall gently
10
11
5
Use screw driver to secure
rame in the wall
4
6
connet the cable to speaker inputs
(+) to (+)
and
(-) to (-)
3
Insert the speaker frame into the wall
SoundWallTM Installation
9
Set the high frequency output level.
(Available only in M/H)
+3
-3
0dB
(-)
(+)
Page 4
Specifications
SoundWall™ H Series
SPECIFICATIONS
Construction
Drive units
Nominal impedance
Sensitivity 2.83V/1M
Power handling
Operating power
Crossover
Frequency response
Twitter level
Grille
Overall Exterior Frame
Dimensions (WxHxD)
Cut Out Dimensions
(H x W)
FINISH
IN-8HIN-6H / 6H(f)
IN-5H
Morel operates a product design improvement policy consequently specifications are subject to alterations without prior notice
Front baffle black PU painted MDF
Woofer: 5" DPC cone 3" Hexatech
TM
voice
coil, External Voice Coil technology (EVC)
Tweeter: 1.1" soft dome, AcuflexTM
coated, HexatechTM voice coil, neodymium magnet motor
6 ohm
86 dB
100W
20-120 W
2,200Hz / 12 dB
45-22,000 Hz
0 / ±3 dB
Metal
7.5" x 10.7" x 3.3"
(191x 272 x 83 mm)
9.6" x 6.4"
(246 x 164 mm)
White
Front baffle black PU painted MDF
Woofer: 6" DPC cone 3" Hexatech
TM
voice
coil, External Voice Coil technology (EVC)
Tweeter: 1.1" soft dome, AcuflexTM coated,
HexatechTM voice coil, double neodymium
magnet motor
6 ohm
88 dB
120W
20-150 W
2,200Hz / 12 dB
38-22,000 Hz
0 / ±3 dB
Metal
8.7" x 12" x 3.2"
(220 x 305 x 82 mm)
10.9" x 7.5"
(278 x 192 mm)
White
Front baffle black PU painted MDF
Woofer: 8" DPC cone 3" Hexatech
TM
voice
coil, External Voice Coil techn
ology (EVC)
Tweeter: 1.1" soft dome, AcuflexTM coated,
HexatechTM voice coil, double neodymium
magnet motor
6 ohm
90 dB
180W
20-200 W
2,200Hz / 12 dB
30-22,000 Hz
0 / ±3 dB
Metal
10.4" x 14.1" x 3.3"
(263 x 357x 83 mm)
12.9" x 9.3"
(329 x 237 mm)
White
Front baffle black painted MDF
Woofer: 5" composite cone 2.1"
Hexatech
TM
voice coil, with
Morel's External Voice Coil
technology (EVC)
Tweeter: 1.1" soft dome,
neodymium magnet motor
6 ohm
86 dB
80W
20-120 W
2,200Hz / 12 dB
45-22,000 Hz
Metal
7.5" x 10.7" x 3.3"
(191x 272 x 83 mm)
9.6" x 6.4"
(246 x 164 mm)
White
SPECIFICATIONS
Construction
Drive units
Nominal impedance
Sensitivity 2.83V/1M
Power handling
Operating power
Crossover
Frequency response
Grille
Overall Exterior Frame
Dimensions (WxHxD)
Cut Out Dimensions
(H x W)
FINISH
IN-8MIN-6M / 6M (f) IN-6X / 6X (f)
IN-5M
SoundWall™ M / X Series
Morel operates a product design improvement policy consequently specifications are subject to alterations without prior notice
Front baffle black painted MDF
Woofer: 6" composite cone 2.1"
Hexatech
TM
voice coil,with
Morel's External Voice Coil
technology (EVC)
Tweeter: 1.1" soft dome, double
neodymium magnet motor
6 ohm
88 dB
100W
20-150 W
2,200Hz / 12 dB
38-22,000 Hz
Metal
8.7" x 12" x 3.2"
(220 x 305 x 82 mm)
10.9" x 7.5"
(278 x 192 mm)
White
Front baffle black painted MDF
Woofer: 6" composite cone 2.8
mm voice coil, Hi grade ferrite
magnet
Tweeter: 1.1" soft dome, double
neodymium magnet motor
6 ohm
90 dB
90W
20-120 W
3,500Hz / 12 dB
45-22,000 Hz
Metal
8.7" x 12" x 3.2"
(220 x 305 x 82 mm)
10.9" x 7.5"
(278 x 192 mm)
White
Front baffle black painted MDF
Woofer: 8" composite cone 3"
Hexatech
TM
voice coil,with
Morel's External Voice Coil
technology (EVC)
Tweeter: 1.1" soft dome, double
neodymium magnet motor
6 ohm
91 dB
150W
20-200 W
2,200Hz / 12 dB
30-22,000 Hz
Metal
10.4" x 14.1" x 3.3"
(263 x 357x 83 mm)
12.9" x 9.3"
(329 x 237 mm)
White
Loading...