Moog Videolarm SM5CF8N, SM5C8N, SM5T8N, SM5TF8N, SM5CF8NE Installation And Operation Instructions Manual
...
© 2013, Moog Videolarm, Inc. All Rights Reserved
S M 5 C 8 N and S M 5 C F 8 N
PoE Ready™ Compact Vandal-Resistant Surface Mount Dome-5”
Installation and Operation Instructions for the following models:
SM5C8N Outdoor 5” PoE surface mount housing for small PTZ camera, conduit input from the
(SM5T8N) side and top of the housing, 30W PoE input, with heater and Dynamic Power Allocation™.
Polycarbonate body and clear/tinted dome. IP66, 1” NPT threads for pendant mount.
SM5CF8N Outdoor 5” PoE surface mount housing for small xed camera, conduit input from the side and the
(SM5TF8N) top of the housing, 30W PoE input, with heater and Dynamic Power Allocation. Polycarbonate body
and clear/tinted dome. IP66, 1” NPT threads for pendant mount.
SM5CF8NE Outdoor 5” PoE surface mount housing for small xed camera, conduit input from the
(SM5TF8NE) side and the top of the housing 30W PoE input, with heater and Dynamic Power Allocation.
Polycarbonate body and clear/tinted dome. IP66, 1” NPT threads for pendant mount.
(no midspan included)
SM5C8NE Outdoor 5” PoE surface mount housing for small PTZ camera, conduit input from the side
(SM5T8NE) and the top of the housing 30W PoE input, with heater and Dynamic Power Allocation.
Polycarbonate body and clear/tinted dome. IP66, 1” NPT threads for pendant mount.
(no midspan included)
Before attempting to connect or operate this product, please read these instructions completely.
www.moogvideolarm.com
81-IN5460
01-10-2013
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with damp cloth.
7 Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8 Cable Runs- All cable runs must be within permissible distance.
9 Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualied installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including ampliers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specied by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
17 This product has been tested and proven to work with the following midspan manufacturer
• PowersDsine • Phihong
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity
of the installation is intact. Failure to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages or injury to anyone or anything struck
by the falling unit.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make future
shipments of the equipment.
2 These Installation and Operating Instructions.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICE-
ABLE PARTS INSIDE. REFER SEVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude
to constitute a risk to persons.
Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica
.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.
Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti nella
letteratura che accompagna l'apparecchio.
SERVICE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
If technical support or service is needed, contact us at
the following number:
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1- 800 - 554 -1124
Limited Warranty for Moog Videolarm Products
Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY PARTS \ LABOR
All Enclosures and Electronics* Five (5) Years
Poles/PolEvators™/CamEvator Three (3) Years
Warrior Series™/Q-View™/IR Illuminators Five (5) Years
SView Series™ Five (5) Years **6 months if used in auto scan/tour operation
Controllers Five (5) Years
Power Supplies Five (5) Years
EcoKit Three (3) Years
Accessory Brackets Five (5) Years
Liberty Dome Three (3) Years
*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an
explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period
of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that
part or the remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any
Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the
warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the
Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the
published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,
or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not
been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any
cost associated with removal of defective product and installation of replacement product is not included in this warranty.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
!!
English
Español
Français
Deutsch
Portuguese
Italiano
Electrical Specifications
Power POE 56V
Input Power: 100 to 240VAC (Midspan)
Power: 0.8A
Frequency: 50 to 60 HZ output
Camera: POE (55VDC)
Heater: 56VDC (max. 20W)
Energía de entrada: 100 a 240VAC (Midspan)
Energía: 0.8A
Frecuencia: 50 a 60 hertzios de salida
Cámara: POE (55VDC)
Calentador: 56VDC (máximo 20W)
Puissance d'entrée: 100 à 240VAC (Midspan)
Puissance: 0.8A
Fréquence: 50 à 60 hertz de rendement
Appareil-photo: POE (55VDC)
Réchauffeur: 56VDC (maximum 20W)
Zugeführte Energie: 100 zu 240VAC (Midspan)
Energie: 0.8A
Frequenz: 50 bis 60 Hz Ausgang
Kamera: POE (55VDC)
Heizung: 56VDC (Maximum 20W)
Poder de entrada: 100 a 240VAC (Midspan)
Poder: 0.8A
Freqüência: 50 a 60 hertz de saída
Câmera: Ponto de entrada (55VDC)
Calefator: 56VDC (máximo 20W)
Alimentazione in ingresso di entrata: 100 a 240VAC (Midspan)
Potere: 0.8A
Frequenza: 50 - 60 hertz di uscita
Macchina fotograca: POE (55VDC)
Riscaldatore: 56VDC (massimo 20W)
SM5C8N SM5CF8N
Contents of Box
*
(1) Mounting Plate
(1) Fixed Bracket
(7) 8 x 32 x 3/8" Bolt
(3) 8 x 32 Nuts
(7) 8 x 32 Star Washers
(1) Mounting Plate
(1) 1/4 x 20 Bolt
(1) 1/4 Flat Washer
(1) 1/4 Lock Washer
(4) M3 6mm Bolt
(4) M3 Lock Washers
(7) 8 x 32 x 3/8" bolts
(2) 8 x 32 Nuts
(2) 94-FSCT01
* FIXED units ONLY
PACKETS
For Surface Mounting Using Side Conduit Entrance
1
(4)
(8)
(1) Mounting Plate
(1) 1/4 x 20 Bolt
(1) 1/4 Flat Washer
(1) 1/4 Lock Washer
(4) M3 6mm Bolt
(4) M3 Lock Washers
(7) 8 x 32 x 3/8" bolts
(2) 8 x 32 Nuts
(4)
Fixed
(2) 94-FSCT01
(1) Mounting Plate
(1) Fixed Bracket
(7) 8 x 32 x 3/8" Bolt
(3) 8 x 32 Nuts
(7) 8 x 32 Star Washers
Etch knockout slightly with utility knife.
Knock and hammer out ⅞ conduit opening
with blunt screw driver
• Golpe de gracia del grabado de pistas levemente
con el cuchillo para uso general. Golpee y resuelva la
abertura del conducto del ⅞ con destornillador
embotado
• Coup de grâce gravure à l'eau forte légèrement avec
le couteau de service. Frappez et résolvez l'ouverture
de conduit de ⅞ avec le tournevis émoussé
• Ätzung-Ausscheidungswettkampf etwas mit
Gebrauchsmesser. Klopfen Sie und hämmern Sie ⅞
Rohröffnung mit stumpfem Schraubenzieher
• KO gravura em àgua forte ligeiramente com faca de
serviço público. Bata e resolva a abertura da
canalização do ⅞ com chave de fenda sem corte
• Espulsore incissione all'acquaforte un po'con la lama
pratica. Batti e risolva l'apertura del condotto del ⅞
con il cacciavite smussato
Loading...