Moog Videolarm QRHPC3-70NA, QRHPC4-70NA, QRHPC4-50NA, QRHWC2-50NA, QRHWC2-70NA Instructions Manual

Product

Instructions

QView Series QRH Rugged Dome

QRHW & QRHP

Before attempting to connect or operate this product,

please read these instructions completely.

81-IN5338

8/8/05

!

1. Read Instructions - All the safety and operating instructions should be read
before the unit is operated.

2. Retain Instructions -The safety and operating instructions should be retained
for future reference.

3. Heed Warnings - All warnings on the unit and in the operating instructions
should be adhered to.

4. Follow Instructions - All operating & user instructions should be followed.

5. Electrical Connections - Only a qualified electrician should make electrical
connections.

6. Attachments - Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

7. Cable Runs - All cable runs must be within permissible distance.

8. Mounting -This unit must be properlyand securely mounted to a supporting
structure capable of sustaining the weight of the unit. Accordingly:
a. Installation should be made by a qualified installer.
b. Installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit,

taking into account both the composition of the mounting surface and
the weight of the unit. Be sure to periodically examine the unit and the
supporting structure to make sure that the integrity of the installation
is intact. Failure to comply with the foregoing could result in the unit
separating from thesupport structure andfalling,with resultantdamages
or injury to anyone or anything struck by the falling unit.

UNPACKING

Unpack carefully. Electroniccomponents can be damaged if improperly handled

or dropped. If an item appears to have been damaged in shipment,replace it
properly in its carton and notify the shipper.

1. The shipping carton and packaging material. They are the safest material in

which to make future shipments of the equipment.

2. These Installation and Operating Instructions.

Be sure to save:

SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS

CAUTION

RISK OF

ELECTRIC SHOCK!

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK, DO NOT EXPOSE

COMPONENTS TO WATER OR MOISTURE.

The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of non-insulated"dangerous voltage" withinthe
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intendedtoalert theuser topresenceofimportantoperating

!

SERVICE

If the unit ever needs repair service, customer should contact Videolarm

(1-800-554-1124) for return authorization & shipping instructions.

TECHNICAL SUPPORT

Videolarm has set-up a 24 hour technical support line for their customers.

and maintenance(servicing) instructionsin theliterature
accompanying the appliance.

24 HOUR TECHNICAL SUPPORT

1-800-554-1124

LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:

PRODUCT CATEGORY PARTS LABOR
All Enclosures and Electronics Three (3) Years Three (3) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R.Illuminators Five (5) Years Five (5) Years
Controllers Three (3) Years Three (3) Years
Power Supplies Three (3) Years Three (3) Years
Accessory Brackets Three (3) Years Three (3) Years
During the labor warranty period, to repair the Product,Purchaser will either return the defective product,freight prepaid, or deliver it to Videolarm Inc.Decatur GA.
The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials
Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact ourTechnical Support Team at 800.554.1124, extension 101.
Videolarm will return the repaired Product freight prepaid to Purchaser.Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty
period or at any time.After the applicable warranty period, Purchaser must pay all labor and/or parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship,then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.
If after investigation Videolarm determines that the reported problem was not covered by the warranty,Purchaser shall pay Videolarm for the cost of investigating
the problem at its then prevailing per incident billable rate.No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire
Product.The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply,at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during

the warranty period which is subjected to any of the following:abuse, improper use:negligence,accident,lightning damage or other acts of God (i.e.,hurricanes,
earthquakes),modification, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization,written in product instructions, or recommended in the service manual for the Product.
Furthermore,Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts (based on usage)
and the end-user has failed to follow such schedule;attempted repair by non-qualified personnel;operation of the Product outside of the published environmental
and electrical parameters,or if such Product’s original identification (trademark,serial number) markings have been defaced,altered,or removed. Videolarm
excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.
All software and accompanying documentation furnished with,or as part of the Product is furnished“AS IS” (i.e., without any warranty of any kind),except where
expressly provided otherwise in any documentation or license agreement furnished with the Product.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

INCLUDING,BUT NOT LIMITEDTO ANY AND/OR ALL IMPLIEDWARRANTIES OF MERCHANTABILITY,FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM
OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.VIDEOLARM HEREBY DISCLAIMS
ANY REPRESENTATIONS OR WARRANTYTHAT THE PRODUCT IS COMPATIBLEWITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS
PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM,IF ANY,AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FORANY CLAIM OF ANY KIND WHATSOEVER,

REGARDLESS OF THE LEGAL THEORYAND WHETHER ARISING IN TORT OR CONTRACT,SHALL NOT BE GREATER THAN THEACTUAL PURCHASE PRICE OFTHE PRODUCT WITH RESPECT TO WHICH
SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLETO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING,BUT NOT
LIMITED TO,COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OFTHE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

EXCEPT FOR THE FOREGOINGWARRANTIES,VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES,EXPRESS OR IMPLIED,

CABLE AND POWER GUIDELINES

This chart shows the proper current needed for power supplies for
Q-View™ cameras. Use Class 2 Power only. Input voltage must
be 24 VAC/VDC.

CAMERAS VOLTAGE CURRENT POWER

1 24 VAC/VDC 102mA 2.5W

2 24 VAC/VDC 210mA 5W

3 24 VAC/VDC 331mA 7.9W

4 24 VAC/VDC 487mA 10.9W

Use the formula below to select the correct power supply for
cameras connected in parallel (positive to positive, negative to
negative):

Total current for a 24 VAC system:
TOTAL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

Power 24VAC, Class 2 Only

26 watts at 24 VAC Heater and Blower

Heater: 25 watts

Blower: 1 watt

Input Connectors (outdoor units):

Camera Power, BNC

(2) screw-down connectors

NOTE: This unit is designed for operation in an upright

position. Installing the QRH upside down may

cause damage to the internal equipment, and

will void the warranty.

GENERAL INSTRUCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

Tamper-proof Allen wrench (supplied)

Be sure the bracket is properly and securely mounted to a

supporting structure capable of rigidly holding the weight of

the entire unit.

INSTALLING QUICK RELEASE BRACKET AND PAN/TILT

CAMERA ASSEMBLY (ALL MODELS)

1. Open the housing by loosening the (3) captive screws

located on the housing ring next to the lower clear dome

(Figure 1). Be careful not to back these all the way out. Twist the

dome slightly in a counterclockwise motion until it stops, then pull

down to remove.

NOTE: 3 Security screws are provided in packet assembly

if desired

Figure 1

Loosen screws only,

do not remove

Remove dome by twisting

counter-clockwise until it

stops, then pull down

2. Clean the inside of the dome. Reattach the housing dome and

secure the (3) captive screws. Do not overtighten the screws.

Tighten only to the point at which the gap between the ring and

the housing top closes (screws should be tightened to 12" lbs.

max).

INSTALLING THE HOUSING ASSEMBLY

FOR WALL MOUNT, QRH

A wall mount bracket comes standard with this unit, and a

template is included to use as a guide for mounting the bracket

to a wall. Choose the desired location for installation and mark

the drill holes using the template. Mount the wall mount bracket

to the wall with (4) bolts (not provided). Run approximately 8" of

wiring out of the wall and into the wall mount.

NOTE: Be sure the hardware and the mounting surface can support

the weight of the wall mount bracket plus the weight of the

housing and drive unit. The load will be subjected to vibration

from the camera motor and wind.

2. The wall mount bracket provided with the rugged housing includes

a location for conduit entry. If you wish to install conduit to the

bracket remove the conduit hole plug. Install fitting from below the

wall mount and secure with conduit nut from inside the bracket.

- 3 -

3. Open the access door on the bottom of the wall mount by

loosening the screw nearest the mounting plate (Figure 2).

Access panel

Figure 2

1. Mount the housing assembly to the mounting bracket and

housing coupling. A safety cable is included with the housing to

temporarily hold it while making wiring connections. Loop the

safety cable over one of the set screws on the housing coupling

and make the appropriate connections using the (2) screw-down

connectors supplied.

2. Undo the safety cable and twist the housing onto the housing

coupling. Secure all (3) setscrews provided on the housing

coupling (Figure 4, next column).

3. Clean the outside of the dome.

4. Attach the wires from the wall to the connector provided, using the

wiring color code chart as a guide.

5. Once all wiring connections are made, place the wires inside the

wall mount bracket and close the access door. Secure with the

screw removed earlier.

6. Clean the outside of the dome.

FOR OPTIONAL PENDANT MOUNT

1. This unit includes a 1 1/2" NPT housing for a standard 1 1/2"

NPT pipe. The RH7C can be used with other brackets

designed with 1 1/2" male pipe threads, such as the Videolarm

WM20G and WM20 wall mount brackets.

2. Attach the housing coupling (Figure 3).

NOTE: Pipe threads should be clean and rust free. Use a

sealer (such as Teflon™ tape or silicone sealer) on the

threads.

Twist and
Secure

Figure 4

Figure 3

Add thread
sealing tape

Wiring Color Code for Power

POWER

1 Camera Power (24 VAC) Red

2 Camera Power (24 VAC) Orange

3 Accessory Power (24 VAC) Yellow

4 Accessory Power (24 VAC) Green

-4 -