Moog Videolarm IPRS01 Installation And Operation Instructions Manual

© 2011, Moog Videolarm, Inc. All Rights Reserved

I P R S 0 1

IP Reset Device

Installation and Operation Instructions for the following model:

IP Reset IP Reset- provides a systematic solution for resetting IP cameras
or wireless systems, lock-ups caused by network issues, wiring
problems and power uctuations by monitoring the output of an IP
camera’s digital signal.

Installation Steps

1. Check the package contents

2. Select Operation Mode

3. Install Hardware
a. Timed Reset Mode
b. Intelligent Reset Mode

4. Read LED Operation instructions

5. Install Software- see IP Reset Manager Software (on CD-ROM)

Before attempting to connect or operate this product, please read these instructions completely.

www.videolarm.com

81-IN5416

01-11-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

The lightning ash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude
to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica

.

The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

UNPACKING

Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.

Be sure to save:
1 The shipping carton and packaging material.

They are the safest material in which to make future
shipments of the equipment.

2 These Installation and Operating Instructions.

Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti nella
letteratura che accompagna l'apparecchio.

SERVICE

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

If technical support or service is needed, contact us at
the following number:

TECHNICAL SUPPORT
AVAILABLE 24 HOURS

1- 800 - 554 -1124

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period
of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that
part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the
Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the
published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,
or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not
been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any
cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

! CAUTION:

IP Reset is not weatherproof. When connected to an outdoor camera Please make sure it is protected by a camera enclosure. Do not open IP Reset or all warranties will be
voided.

! WARNING:

To prevent re or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the unit. Refer servicing to qualied personnel only.

Product Specifications

!!

IPRS01

IPRS01 Power Requirements

Input Voltage: 5 to 24 Volts AC/DC

Operating Current: 12ma

English

Device Power Requirements

Maximum Operating Current: 2 Amps

Content of Box

Maximum Switching Current: 5 Amps

I/O Detect Input

Input Voltage: -25VDC to +25VDC

Input Drive Current: 3ma @ 12V Typ.

Threshold: +1.9 VDC

I/O Cable Length: 6" or 15.2cm

Timer Mode Reset Cycle

12 Hours

Power Reset Period

5 Seconds

Environmental

Temperature: -40 to 158 Degrees F

-40 to 70 Degrees C

Humidity: 5 to 95 % non-condensing

m

o

c

.

m

r

a

l

o

Application Soft-

e

d

i

v

t

a

ware

t

r

o

p

p

for

u

s

o

t

l

i

IP RESET

a

m

-

e

d

n

e

s

r

o

4

2

1

1

-

4

5

5

-

0

0

8

-

1

l

l

a

c

t

r

o

p

p

u

s

r

o

F

IPRS01

.

n

e

d

d

i

b

r

o

f

i

y

l

t

o

c

i

n

r

i

t

s

s

IPRS01 Serial # 001656

24Vac

12Vdc

Orange Orange/Black Black

Red(+) Red/Black(+)

Orange(-) Orange/Black(-)

I

P
R

S
0

1

S
e

r
i
a

l

24

#

V

0

Vi

ac

0

n

1

6
5

R

6

ed Red

1
2

Ora

Vd

w

ng

V

it

c

o

e O

u

R

t

ed

/B

(+) Re

Ora

ra

la

ng

n

ck

g

e

e

/

(-)Oran

B
la

d/B

ck

lac

k

ge

B

(

+

/B

)

l
a
ck

(-)

y

w

i

t

h

F

C

C

s

t

a

n

d

a

r

d

s

.

A

n

y

d

u

p

l

i

c

a

t

Vin Vout Alarm

Red Red/Black Brown

Te
s
te
h
F
CC

A

B
rown
lac
k

p

l

d
to

co

m
s
t
an

d

a

rds

la
r
m

o

m

p
ly

t

e

d

t

o

c

with FCC standards

F

o

r

V

e

v

i

c

e

s

o

n

l

y

.

T

e

s

Testedto comply

i

d

e

o

l

a

r

m

I

P

R

S

0

1

d

Dimensions

Enclosure: 1.97" x 1.38" x 0.79"

50mm x 35mm x 20mm

NOTES:

² Ratings can be changed to meet customer’s requirements for
large orders. For the IPRS01 Reset Mode, your equipment must have
an I/O. If I/O cable is not connected (or incorrectly connected).
IPRS01 will operate in Timed Mode.

*** Pan Tilt boxed separately along with its instructions.

Operating Modes

The IP Reset operates in one of two modes, Intelligent Reset Mode and Timed Reset Mode. IP Reset automatically detects the operating mode by monitoring the I/O

Detect input. If IP Reset detects a change in the I/O Detect input, it will enter the Intelligent Reset mode. Otherwise, IP Reset will remain in Timed Reset mode. You

can choose to use Timed Mode by twisting the I/O Detect wires together and securing them with the wire nut.

Intelligent Reset Mode

The Intelligent Reset Mode monitors a relay output on the device being protected. The relay output on the IP device is commanded to toggle at a predetermined

interval using IP Reset Manager Software or other network software designed to support IP Reset. When IP Reset detects the loss of the relay toggle, after a

predetermined detection period, it power restarts the protected device. Generally, a power reset will restore the device to proper operation. After 2 failed attempts to

restore the device’s operation, IP Reset will re-start the protected device once every four hours (fault detection mode).

Timed Reset Mode

The Timed Reset Mode, simply cycles power on the protected device every 12 hours. When used in Timed Reset mode, IP Reset connects directly inline with the

device’s power, does not use the I/O Detect Cable and does not require any remote commanding software.

NOTE:

If Timed Reset Mode is used on a PTZ camera, the camera will typically reset to its home position upon reset. For this reason, we recommend using Intelligent Reset

Mode whenever possible for PTZ cameras.

Output Relay Conguration and Connections

Output Relay Conguration

The relay output congurations vary based on the manufactures design. Because of these variations, the IP Reset I/O Detect input needs to operate in one of three
ways. Refer to your camera user manual for more information regarding the output relay conguration of your camera.

Dry Contact

The rst and most common method requires the IP Reset to supply current to the dry contacts of a relay. This conguration is shown in Figure 5.

BROW N

Figure 5: Dry Contact Relay I/O
Detect Connection

Camera
Dry Contac t

I/O Detect Cable

BLACK

Passive Solid-State

The second method is similar, requiring the IP Reset to supply current to an open collector output transistor. This conguration is shown in Figure 6.

BROW N

Camera Open
Colle ctor Rel ay

Appendix A – Output Relay Conguration and Connections (cont.)

I/O Detect Cable

BLACK

Figure 6: Passive Solid-State Relay I/O
Detect Connection

Active Solid-State

The third and least common method is the emitter follower where the camera output supplies the current used for detection. In this conguration is shown in
Figure 7.

+ Volts

Camera
Solid St ate
Sour cing Rel ay

I/O Detect Cable

Figure 7: Active Solid-State Relay I/O
Detect Connection

BROW N

BLACK

Hardware Installation

The hardware installation depends upon the desired operating mode - Timed Reset Mode or Intelligent Reset Mode.

Timed Reset Mode Installation

1. Do not connect I/O Detect cable. Instead, twist wires together with provided wire nut.

2. Connect the power output pin from the IP Reset to the Power input on your device

3. Connect the power from the transformer to the power input in the IP Reset.

4. No IP Reset Manager Software installation is necessary.

Your IP Reset STD is now connected in Timed Mode. Your protected device should be operating and
power reset once every 12 hours.

IP RESET

IP Reset® Intelligent Reset Mode Installation

Operating the IP Reset® Intelligent Reset Mode requires an output connection to the protected device via the I/O Detect cable. The below illustrates the typical
connections for Intelligent Reset Mode

! WARNING !

If Intelligent Reset Mode connection is incorrect and IP Reset® does not detect I/O communication, IP Reset will remain in Timed Reset Mode and re-start your
device once every 12 hours.

1. Locate your camera in the IP Camera Compatability Chart (Appendix A). If your camera is not
listed, please contact Videolarm at (800)-554-1124.

2. Connect the Brown I/O Detect wire to the I/O terminal specied for your device.

3. Connect the Black I/O Detect wire to the I/O terminal specied for your device.

4. Connect the power output pin from the IP Reset to the Power input on your device.

5. Connect the power from the transformer to the power input in the IP Reset.

6. Add your device’s conguration to the IP Reset Manager Software or Network video recording
(NVR) software (See IP Reset Manager Software installation in CD-ROM).

Note 1: Connection polarity MUST be observed for all devices.
Note 2: If the input connections need to be modied, the Brown wire is plus VDC and the Black
wire is ground (0 VDC).

IP RESET

IP Reset® LED Operation

LED Operation

Green LED – Device Power Indicator

• ON : Power On to Device

• OFF : Power Off to Device

Hardware Installation (cont.)

Yellow LED – Communication/Signal Status

• Timed Mode : Flashes every second

• Intelligent Mode : Flashes every 90 Seconds (On = input High, Off = input Low)

Red LED – Operation Mode Indicator

• ON : Intelligent Mode, device operating as expected

• OFF : Timed Mode

• Flashing : Intelligent Mode, device fault detected