Moog Music MOOG 104HP, MOOG 60HP User`s manual
MOOG 104HP EURORACK CASE
2
WHAT’S INCLUDED
104HP EURORACK CASE
10 PIN TO 16 PIN
RIBBON POWER CABL E
SCREWS
WHAT’S NEEDED
PHILLIPS HEAD SCREWDRIVER
EURORACK POWER SUPPLY
MODULE W/ FLYING BUS BOARD
x1 x1
3
POWER MODULE INSTALL ATION
You will need to install a Eurorack power supply module w/ flying bus board to power your Eurorack modules.
Determine which side of the case you want to install your module in.
Shif t all sliding nut s in the case to the opposite side of w here you plan to install the module.
Slide the appropriate number of nuts (2 to 4) over for installing the module.
d
Loosely thread (2 to 4) of the included screws through the holes on the module.
e
Slide the module in to place and firmly tighten the screws.
4
MODULE INSTALLATION
Every Eurorack module comes with a ribbon power cable that connects to the module itself, and to the flying bus board.
WARNING: Check the documentation for each module to ensure you are connecting the ribbon cable properly.
Shif t all sliding nut s in your case to the opposite side of where you plan to install the module.
Slide the appropriate number of nuts (2 to 8) over for installing the module.
Connect the ribbon power cable included with your Eurorack module to the module itself and the flying bus board.
d
Loosely thread (2 to 8) of the included screws through the holes on the module.
e
Slide the module in to place and firmly tighten the screws.
x52
x1 x1
5
MOTHER-32 INSTALLATION
The 104HP case comes with a 10-pin to 16-pin ribbon power cable for a Mother-32. Details for removing Mother-32 from it s
case and installing it into a Eurorack case are found on Page 52 of the Mother-32 manual.
6
REMOVING SLIDING NUTS
Your case comes with extra sliding nuts to ensure you have more than enough. These extras are easily removed if desired.
Remove all 4 screws from one side of the Eurorack case to easily remove the metal shield and wood side.
Slide out ex tra nuts.
Reins tall the metal shield and wood side using the 4 screws.
MOOG 60HP EURORACK CASE
2
WHAT’S INCLUDED
60HP EURORACK CASE
SCREWS
WHAT’S NEEDED
PHILLIPS HEAD SCREWDRIVER
EURORACK POWER SUPPLY
MODULE W/ FLYING BUS BOARD
x1
3
POWER MODULE INSTALL ATION
You will need to install a Eurorack power supply module w/ flying bus board to power your Eurorack modules.
Determine which side of the case you want to install your module in.
Shif t all sliding nut s in the case to the opposite side of w here you plan to install the module.
Slide the appropriate number of nuts (2 to 4) over for installing the module.
d
Loosely thread (2-4) of the included screws through the holes on the module.
e
Slide the module in to place and firmly tighten the screws.
4
MODULE INSTALLATION
Every Eurorack module comes with a ribbon power cable that connects to the module itself, and to the flying bus board.
WARNING: Check the documentation for each module to ensure you are connecting the ribbon cable properly.
Shif t all sliding nut s in your case to the opposite side of where you plan to install the module.
Slide the appropriate number of nuts (2 to 8) over for installing the module.
Connect the ribbon power cable included with your Eurorack module to the module itself and the flying bus board.
d
Loosely thread (2 to 8) of the included screws through the holes on the module.
e
Slide the module in to place and firmly tighten the screws.
x30
x1 x1
5
REMOVING SLIDING NUTS
Your case comes with extra sliding nuts to ensure you have more than enough. These extras are easily removed if desired.
Remove all 4 screws from one side of the Eurorack case to easily remove the metal shield and wood side.
Slide out ex tra nuts.
Reins tall the metal shield and wood side using the 4 screws.
Loading...