Moog IGDW75C1N Installation Instructions
Installation and Operation Instructions
Before attempting to connect or operate this product, please
read these instructions completely.
Igloo Dome
Air-Conditioned Camera Enclosure Solution for Hot, Humid Climates
IGDW75C1N.............. Outdoor air conditioned dome housing with wall and pole mount, clear polycarbonate dome, with 240VAC input, heater / blower,
120 to 24VAC transformer for xed camera
IGDW75T1N............... Tinted version
IGDW7CN-3............... Outdoor IP network ready 7” air conditioned PTZ camera system with 36x zoom day and night camera, MPEG-4 and MJPEG video
compression, full D1. Clear dome, with 24Vac input, heater / blower
IGDW75CS-3............. Outdoor analog version of the IGDW7CN-3
© 2013, Moog Inc. All Rights Reserved
Moog Inc.
Sensor and Surveillance Systems
3650 Woodhead Drive Northbrook, IL. USA 60062
+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com
81-IN5434 111213
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
avvertire l’utente alla presenza delle istruzioni importanti nella
MADEIN
BUY AMERICA COMPLIANT • COUNTRY OF ORIGIN U.S.A.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with damp cloth.
7 Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8 Cable Runs- All cable runs must be within permissible distance.
9 Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. This installation should be made by a qualied service person and should conform
to all local codes.
b. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including ampliers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specied by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualied service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity
of the installation is intact. Failure to comply with the foregoing could result in the unit separating
from the support structure and falling, with resultant damages or injury to anyone or anything struck
by the falling unit.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICE-
ABLE PARTS INSIDE. REFER SEVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of non-insulated
“dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude
to constitute a risk to persons.
Este símbolo se piensa para alertar al usuario a la presencia
del “voltaje peligroso no-aisIado” dentro del recinto de los
productos que puede ser un riesgo de choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la presence
“de la tension dangereuse” non-isolée dans la clôture de
produits qui peut être un risque de choc électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença “di
tensão perigosa non-isolada” dentro do cerco dos produtos
que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla presenza
“di tensione pericolosa” non-isolata all’interno della
recinzione dei prodotti che può essere un rischio di scossa
elettrica
.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
UNPACKING
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make future
shipments of the equipment.
2 These Installation and Operating Instructions.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones importantes
en la literatura que acompaña la aplicación.
Ce symbole de point d’exclamation est prévu pour alerter
l’utilisateur à la presence des instructions importantes dans
la littérature accompagnant l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der Literatur
alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido alertar o
usuário à presença de instruções importantes na literatura
que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
letteratura che accompagna l'apparecchio.
SERVICE
If technical support or service is needed, contact us at
the following number:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1- 800-554 -1124
Product Warranty Registration
Register Your Products Online
www.moogS3.com/technical-support/product-registration
Moog values your patronage. We are solely committed to providing you with the highest quality products and
superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand
behind every product we sell.
See full warranty details at www.moogS3.com/technical-support/warranty-plan/
:
• Simple and Trouble-Free RMA process
• Product / software updates
• Special promotions
• Eliminate the need to archive purchase documents such as receipts, purchase orders, etc.
Limited Warranty for Moog Products
MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-MANUFACTURER
THE LIABILITY OF Manufacturer, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS
OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT
Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY PARTS \ LABOR
All Enclosures and Electronics Five (5) Years
Accessory Brackets Five (5) Years
Controllers Three (3) Years
Power Supplies / IR Illuminators Three (3) Years
™
Poles / PolEvators
Warrior Series
SView Series
DeputyDome
EXO Series
EXO Series
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Manufacturer at Moog Decatur
Operations, 2525 Park Central Boulevard, Decatur, Georgia, 30035. The Product to be repaired is to be returned in either its original carton or a similar package affording
an equal degree of protection with a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our
Technical Support Team at 800.554.1124, extension 101. Manufacturer will return the repaired product freight prepaid to Purchaser. Manufacturer is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an explanation
of the claim shall be given promptly by Purchaser to Manufacturer. All claims for warranty service must be made within the warranty period. If after investigation,
Manufacturer determines the reported problem was not covered by the warranty, Purchaser shall pay Manufacturer for the cost of investigating the problem at its then
prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period of the entire Product. The specic warranty on
the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the Product parts warranty,
whichever is greater.
/ CamEvator Three (3) Years
™
™
™
, NiteTrac™, Igloo Dome, PurgeDome
™
Dome and Fixed Camera Systems* Three (3) Years 6 months if used in auto scan / tour operation
™
GeminEye Visible and Thermal Camera Systems One (1) Year
/ Q-View
™
Three (3) Years
Three (3) Years 6 months if used in auto scan / tour operation
™
Three (3) Years 6 months if used in auto scan / tour operation
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Manufacturer’s sole obligation is to supply (or pay for) all labor necessary to repair any Product
found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Manufacturer shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty
period which is subjected to any of the following: abuse, improper use, negligence, accident, or acts of God (i.e., hurricanes, earthquakes), modication, failure of the
end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance procedures recommended by the International Security
Industry Organization, written in product instructions, or recommended in the service manual for the Product. Furthermore, Manufacturer shall have no liability where a
schedule is specied for regular replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted
repair by non-qualied personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original identication
(trademark, serial number) markings have been defaced, altered, or removed. Manufacturer excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS
and excludes used Products which have not been sold by Manufacturer to the Purchaser. All software and accompanying documentation furnished with, or as part of the
Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with
the Product. ANY COST ASSOCIATED WITH REMOVAL OF DEFECTIVE PRODUCT AND INSTALLATION OF REPLACEMENT PRODUCT IS NOT INCLUDED IN THIS WARRANTY.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY
CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.
PRODUCTS OR NON-MANUFACTURER RECOMMENDED PRODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REPLACEMENT LABOR COSTS, REIMBURSEMENT, OR DAMAGES ON ACCOUNT OF THE LOSS
OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
Electrical Specifications
!!
Igloo Dome
Power 120VAC .
50/60 H
2.
300 WATTS.
English
Tools Required: Phillips Head Screwdriver.
Ceiling Support Wires(14 AWG wire min.)
Energía 120VAC.
50/60 H
300 VATIOS.
Español
Las herramientas requirieron: Destornillador principal
Phillips.
Alambres de la ayuda del techo
(14 de alambre del AWG Min.)
Puissance 120VAC.
50/60 H
300 WATTS.
Outils requis : Tournevis phillips.
Français
Fils de soutien de plafond (14 de fil d'A.W.G. mn)
.
2
.
2
Mechanical Options
1. Air ow sensor available to be combined with camera output systems
to monitor the eectiveness of air lter. If improper air ow is detected,
sensor will send alarm. If user by passes air ow sensor, air lter should
be changed approximately every 6 months (depending on monitoring
environment).
2. The Igloo Dome incorporates an automatic cool-down safety
precaution system which deactivates the power of both the camera and
cooling system when internal temperatures exceed 167°F (75°C). Once
safe operating conditions resume, the camera and cooling system will
reactivate.
3. Condensation and water run-o is a by product of the Igloo Dome's
cooling system. To prevent damage to the internal electrical
components, the Igloo Dome consists of a water run-o hose, located
underneath the optical dome. Please use caution that small amounts of
water accumulation will be present directly underneath the Igloo Dome,
resulting in slippery conditions.
* A 50/50 blend of propylene glycol and water has a freezing point of
-26°F. If lower temperature protection is required, it can readily be
attained by increasing the concentration of propylene glycol Antifreeze for example; a 60/40 blend of Antifreeze and water gives antifreeze
protection to -54°F.
Deutsch
Portuguese
Italiano
Energie 120VAC.
50/60 H2.
300 WATT.
Werkzeuge erfordert: Kreuzkopfschraubenzieher.
Decken-Stützdrähte (14 AWG-Lehredraht Min.)
Poder 120VAC.
50/60 de H2.
300 WATTS.
As ferramentas exigiram: Chave de fenda principal de
Phillips.
Fios da sustentação do teto
(14 de fio Calibre de diâmetro de fios Min.)
Potere 120VAC.
50/60 di H2.
300 WATT.
Gli attrezzi hanno richiesto: Cacciavite phillips. Legare
di sostegno del soffitto
(14 del legare dell'AWG min.)
1/2" LOWER
MOUNTING BOLTS
STEP 1:
POSITION LOWER MOUNTING BOLTS, WASHERS
AND NUTS AS SHOWN ABOVE., THREAD THE NUTS
UNTIL FLUSH WITH BOLT ENDS
Position lower mounting bolts, washers and nuts as
shown above. Thread the nuts until flush with bolt ends.
• Coloque pernos, arandelas y tuercas más bajos de montaje como se
muestra arriba. Rosque las tuercas hasta rubor con los extremos de
perno.
• Placez les boulons de fixation, les rondelles et les écrous inférieurs
comme montré ci-dessus. Filetez les écrous jusqu'à l'éclat avec des
extrémités de boulon.
• Bringen Sie unterere Befestigungsbolzen, Unterlegscheiben und Nüsse
wie gezeigt oben in Position. Verlegen Sie die Nüsse bis bündiges mit
Schraubbolzenenden.
• Posicione uns mais baixos parafusos, arruelas e porcas de montagem
como mostrado acima. Rosqueie as porcas até o resplendor com
extremidades de parafuso.
• Posizioni i bulloni, le rondelle ed i dadi più bassi di attacco come
indicato sopra. Filetti i dadi fino ad a livello dell'estremità di bullone.
Content of Box
COOLANT
1
2
Thread one retainer extrusion at the end of steel band,
allowing 1” (254mm) of band out. Beveled end of
extrusion to be out.
• Un hilo de retención de extrusión en la final de la banda de acero,
permitiendo 1 "(254 mm), de banda a cabo. Biselados final de
extrusión que se fuera.
• Thread extrusion une retenue à la fin de la bande d'acier, permettant
à 1 "(254mm) de la bande de. Biseauté fin de l'extrusion de ne pas être.
• Rijg een vasthoud-extrusie op het einde van stalen band, waardoor 1
"(254 mm) van de band uit. Schuine einde van de extrusie worden
uitgesloten.
• Passe um retentor extrusão no final da banda de aço, permitindo 1
"(254 milímetros), da banda fora. Biselado final de extrusão de ser fora.
• Iniziatore di estrusione uno fermo alla fine di banda di acciaio,
consentendo 1 "(254 millimetri) di banda fuori. Smussato fine di
estrusione di essere fuori.
Loading...