D7 DELAY
pedal
Precautions
PLEASE READ CAREFULLY BEFORE PROCEEDING
Power Supply
Please connect the designated AC adapter to an AC outlet of the correct voltage. Be sure to only use an AC adapter which supplies 9V DC, 200mA. Unplug the AC power adapter when not in use or during electrical storms.
Location
To avoid deformation, discoloration, or other serious damage, do not expose this unit to the following conditions:
• Direct sunlight or other heat sources • Magnetic fields
• Excessively dusty or dirty locations • Strong vibrations or shocks
• High humidity or moisture
Radio Frequency Interference
Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions.
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Features
● 6 di erent types of MOOER's customizable delay e ects.
● Tap Tempo to control delay timing.
● Trail On function allows the e ects to fade out naturally.
● Storable presets.
● 150-second capacity LOOPER.
Layout
|
|
|
|
|
|
|
11 |
10 |
|
|
|
|
|
|
6 |
|
|
|
|
|
|
|
|
TWEAK.1 |
|
|
|
|
MIX |
|
|
9 |
|
|
|
|
|
|
7 |
|
|
|
|
|
|
5 |
|
TWEAK.2 |
|
|
|
TIME |
|||
|
|
|
|
||||
2 |
|
|
|
|
|
|
8 |
3 |
|
|
|
|
|
|
|
|
|
|
|
F.B |
|
||
SAVE |
|
|
|
|
|
||
4 |
|
|
|
|
|
<![if ! IE]> <![endif]>DELAY |
|
TAP |
|
|
|
|
|
1 |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Ta |
pe |
|
|
|
|
|
Li |
|
|
||
|
|
|
|
|
|
||
|
|
|
|
qui |
|
||
12 |
R |
ai |
nb |
o |
d |
|
|
|
|
w |
|
||||
|
|
|
|
||||
|
|
G |
al |
|
|||
|
|
|
|
||||
|
|
|
|
|
|||
M |
o |
d |
|
a |
xy |
|
|
ver |
|
|
|||||
se |
|
||||||
|
|
|
|||||
|
L |
|
|||||
|
|
|
|
||||
|
|
|
|
|
|
||
|
|
o |
w b |
|
|
||
|
L |
|
|
|
it |
|
|
|
|
o |
o |
p |
|
|
|
|
|
|
|
er |
|
1. Footswitch
● Switch on/o . Tap Tempo.
2. SAVE button
● Press to save presets.
3. LED indicators
● Indicates selected e ect or if LOOPER is active.
4. OUTPUT
● 1/4'' mono jack.
5. INPUT
● 1/4'' mono jack.
6. MIX control
● Control the wet/dry ratio of the signal.
7. TIME control
● Control the delay timing.
8. F.B control
● Control delay feedback levels.
9. TWEAK.2
● Refer to the TWEAK list.
10. TWEAK.1
● Refer to the TWEAK list.
11. DC IN
● For 9V power supply. (Negative inside
< >, 200mA).
12. E ect name.
Instructions
1. E ect type switch
Press the SAVE button to switch between 7 types of e ects (including LOOPER).
LED indicator shows selected e ect.
2. Edit Presets
Rotate the control knobs to edit presets. LED indicator will blink until users
press and hold SAVE button to store current changes.
3. Tap tempo
Press and hold footswitch for 1 second to enter tap tempo function. The SAVE
button will turn red. Press footswitch several times to get your desired delay
timing. The Tap Tempo function will quit after 3 seconds.
4. Trail On
Power o pedal. Press and hold the footswitch while powering on the pedal
again to switch between Trail On/O . SAVE button will turn red when Trail is
on; blue means Trail is o . Trail On allows the e ect to fade out naturally
when it is switched o during play.
5. LOOPER
Press SAVE button. Switch to LOOPER mode. TWEAK 1 controls INPUT LEVEL.
Please adjust input volume level as you desire. TWEAK 2 controls LEVEL of
recorded tracks.
REC - Press footswitch to start recording. SAVE button will turn RED.
PLAY - Press SAVE button during REC/DUB to play the recorded track. SAVE
button will turn BLUE.
DUB - Press footswitch during PLAY. SAVE button will turn RED.
STOP - Press footswitch twice quickly during REC/PLAY/DUB to stop recording.
CLEAR - Press the footswitch twice quickly then hold during REC/PLAY/DUB
to clear all the tracks. You can press and hold the footswitch during STOP to
clear the tracks as well.
NOTICE - The recorded tracks cannot be stored after the pedal is powered o .
Maximum recording capacity is 150 seconds.LOOPER mode has a built-in
delay e ect. The built-in delay is not adjustable.
6. Factory Reset
Power o the pedal. Press and hold SAVE button then power on the pedal.
The LED indicator will start to blink. Release the SAVE button to finish factory
reset.
E ect list
MODE |
TWEAK.1 |
TWEAK.2 |
Description |
TAPE |
Filter |
Vibrato(Mix) |
Tape machine delay |
LIQUID |
Step-Phaser |
Step- |
Liquid like modulation delay |
(Rate) |
Phaser(Mix) |
||
RAINBOW |
Stutter (Rate |
Pitch Degree |
Pitch will change with the speed of Stutter |
&Depth) |
|||
Galaxy |
Post-Slow |
Chorus(Mix) |
Slow gear delay |
gear |
|||
MOD- |
Flanger |
Flanger(Mix) |
Reversing play delay |
VERSE |
(Rate) |
||
LOW-BIT |
Pre-Slow |
Low bit |
Delay with slow gear and low bit e ects |
gear |
|||
LOOPER |
Input level |
Play level |
Looper recording |
Notice: Pre-slow gear fed by dry signal. Post-slow gear fed by wet signal.
Specifications
Input: 1/4" mono jack (impedance 2.2M Ohms)
Output: 1/4" mono jack (impedance 100Ohms)
Power supply: 9V DC transformer (internal negative external), MOOER Micro
Power is recommended
Current Draw: 200mA
Dimensions: 93.5mm(D) x 42mm(W) x 52mm(H)
Weight: 155g
Accessories: User Manual*
*Disclaimer: Parameters may update without notice.