Mooer Baby Bomb 30 Owner`s Manual

30W Digital Micro Power AMP

Precautions

PLEASE READ CAREFULLY BEFORE PROCEEDING

Power Supply

Use the correct AC outlet to connect the power adapter.Please use a negative
internal 24V (± 10%) power transformer, otherwise it will cause damage
to equipment, fire or other problems.When unused or thunderstorms please
unplug the power supply.

Connections

Before connecting the device or disconnecting it, be sure to turn off the power and
other equipment, which will help to avoid malfunction and damage to other
equipment. Also, make sure that all cables and power cords are disconnected before
moving the unit.

Place the place

To prevent deformation, discoloration, and other serious damage, avoid the following:
Direct sunlight
Magnetic fields
Excessively dusty or dirty location
Strong vibration or shock

Electrical interference

When using the unit, the radio and the TV may cause interference. Use the unit

away from the radio and the TV.

Clean

Please use a dry, soft cloth to clean the unit. If necessary, wipe with a slightly moist
cloth. Do not use rough clean powder, alcohol, paint thinner, wax, solvent, detergent
and chemical agents such as impregnated wipes.

Operating

Do not use the switch and control elements violently.
Do not allow paper, metal, and other objects to fall into the machine.
Be careful not to fall, do not subject it to shock and excessive pressure.

FCC certification

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference

that may cause undesired operation.

Heat sources
Extreme temperature or humidity
High humidity or moisture

Features

30 Watt maximum power output
Master volume control can provide smooth post stage overdrive
WARM/BRIGHT switch to adjust the power stage presence
Built in overcurrent protection
Can be connected to speaker cabinets with a load of 8 Ohm or 16 Ohm

Pedal layout

1.IN:

06

Connect the output of your

WARM

05

BRIGHT

MASTER

SPEAKER OUT 8Ω~16Ω

02

preamp or pedalboard to the INPUT

using a standard 1/4" jack cable

03

2.SPEAKER OUT:

Connect to a guitar speaker cabinet

input rated at 8 Ohms or 16 Ohms

using an unbalanced speaker cable

01

3.MASTER:

Adjusts the output volume

4.LED:

04

When the Baby Bomb has power

connected the LED will illuminate

5.WARM/BRIGHT：

Adjusts the presence of the

Baby Bomb output

6.DC IN:

Connect a DC 24V 2A

power supply

Connection instructions

1.Connect the DC 24V 2A power supply to the DC IN of Baby Bomb

2.Connect the output of your Preamp or pedalboard to the INPUT of Baby Bomb

3.Connect the SPEAKER OUT of Baby Bomb to the input of your guitar
speaker cabinet using an unbalanced speaker cable. DO NOT connect to a
speaker unless it has and input impedance of 8 Ohms or 16 Ohms

Note: For best results connect your Overdrive and Distortion effects before your
preamp in the signal chain. Connect your modulation and time based effects
(Delay, reverb, etc.) after the preamp and before the BABYBOMB in your signal
chain.

BABY

CABINET

Model: Baby Bomb 30

Output load: 8-16 Ohms
Output power: 30W
Power supply: DC 24V, 2A DC,
Size: 93.5mm (D) x 42mm (W) x 52mm (H)
Weight:144g
Accessories: User manual,Micro Power

BOMB 30

WARM

BRIGHT

MASTER

SPEAKER OUT 8Ω~16Ω

EFFECT

*Notes：Any specification’s update will not be amended in this manual.

MICRO

PREAMP

DC9V

CH/CAB

CH/CAB

OD/Dist

Part No:620010639