Mooer A7 AMBIANCE User manual
A7 AMBIANCE
Reverb Pedal
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Power Supply
Please connect the designated AC adapter to an AC outlet of the correct voltage.
Be sure to only use an AC adapter which supplies 9V DC 200mA. Unplug the AC
power adapter when not in use or during electrical storms.
Location
To avoid deformation, discoloration, or other serious damage, do not expose
this unit to the following conditions:
● Direct sunlight or other heat sources
● Magnetic fields
● Excessively dusty or dirty locations
● Strong vibrations or shocks
● High humidity or moisture
Radio Frequency Interference
Radios and televisions placed nearby may experience reception interference.
Operate this unit at a suitable distance from radios and televisions.
Cleaning
Clean only with a soft, dry cloth. If necessary, slightly moisten the cloth.
Do not use abrasive cleanser, cleaning alcohol, paint thinners, wax,
solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Features
● 7 di erent reverb e ects from classic to psychedelic.
● Choose between INFINITE trail function or the more traditional“Trail On”
function.
● Bu er bypass.
● Storable preset for each e ect.
● Firmware updatable via USB.
Layout
5 |
|
|
|
|
|
|
1 |
|
|
|
|
|
|
2 |
|
|
X |
|
|
|
MIX |
||
|
|
|
|
|
|||
6 |
|
|
|
|
|
|
3 |
CHAOS |
|
|
DECAY |
8 |
|||
7 |
|
|
|||||
|
|
|
|||||
|
|
|
|
|
|
4 |
|
11 |
SAVE |
|
|
TONE |
|
||
9 |
|
|
|
|
|
<![if ! IE]> <![endif]>AMBIANCE |
|
|
INF |
|
|
|
|
10 |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
P |
|
|
|
|
|
|
|
|
la |
|
||
|
|
|
H |
|
te |
|
|
|
|
|
all |
|
|||
|
|
|
Wa |
|
|
||
|
|
|
Sh |
|
rp |
|
|
|
|
|
ake |
|
|||
|
|
|
C |
|
|||
|
|
|
|
|
|
|
|
|
|
|
ru |
|
|
||
|
|
S |
hi |
|
sh |
|
|
|
|
|
|
|
|
||
|
|
|
m |
m |
|
|
|
|
|
|
Dr |
|
er |
|
|
|
|
|
ea |
m |
|
||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
12 |
|
<![if ! IE]> <![endif]>USB |
|
|
|
|
1. DC 9V
● Connect to 9V power supply.
2. MIX
● Dry/wet signal mix control
3. DECAY
● The decay control of reverb
4. TONE
● Tone control of reverb
5. X
● the size of the virtual room control
6. CHAOS
● Special e ects control
7. SAVE
● Saving preset
8. INPUT
● 1/4'' mono jack
9. OUTPUT
● 1/4'' mono jack
10. Footswitch
● Switch on/o the pedal.
11. LED indicators
● Showing current e ect type
12. USB port
● Firmware update
Instructions
1. Switch e ect type
Power on the A7. Press the SAVE button to switch between 7 types of reverb
e ects.
2. Parameter editing
Rotate control knobs to change the parameters of e ects directly. LED
indicators will blink after any change is made. Press and hold SAVE button to
save the change.
3. Infinite Trail
Press and hold the footswitch during play to activate INIFINITE function. The
trail will continue until manually switched o .
4. Trail on
Power o pedal. Press and hold the footswitch while powering on the pedal
again to switch between Trail On/O . SAVE button will turn red when Trail is
on, blue means Trail is o . Trail On allows the e ect to fade out naturally when
it is switched o during play.
5. Factory Reset
Power o the pedal. Press and hold SAVE button then power on the pedal. The
LED indicator will start to blink. Release the SAVE button to finish factory reset.
Reverb Type |
Description |
PLATE |
Based on a traditional mechanical plate reverb |
HALL |
Large spacious reverb with a long decay. Can be changed to |
ROOM/CHURCH reverb by rotating the X control. |
|
WARP |
Modulated reverb |
SHAKE |
Shaking modulated reverb |
CRUSH |
Reverb with LOFI e ect |
SHIMMER |
Reverb with octave e ect |
DREAM |
Reverb with slow attack e ect and modulation e ect |
Specifications
Input: 1/4" mono jack (impedance 2.2M Ohms)
Output: 1/4" mono jack (impedance 100 Ohms)
Power supply: 9V DC transformer (internal negative external), MOOER Micro
Power is recommended
Current Draw: 200mA
Dimensions: 93.5mm(D) x 42mm(W) x 52mm(H)
Weight: 155g
Accessories: User Manual*
*Disclaimer: Parameters may update without notice.
Loading...