Mood Media MULTIPLAY 7200 User Manual

MULTIPLAY 7200®

Instructions for use

CONTENTS

Introduction .............................................................................................................. 2

Precautions to take before using .................................................................................. 3

Unpacking ................................................................................................................ 3

Description and illustration ......................................................................................... 5

Zoning ..................................................................................................................... 6

Switching on ............................................................................................................. 7

Using the display’s keys ............................................................................................. 8

Stopping the MP 7200® ............................................................................................. 8

The serial number...................................................................................................... 8

Menu functions of the MP 7200® ................................................................................. 9

Selection of the zone ............................................................................................... 10

I. MUSIC ........................................................................................................... 11

1) Immediate broadcast of a program (Select day: immediately) ............................... 12

2) Musical programming of a whole week (Select day: Every day) ............................. 12

2a: Power time .................................................................................. 12

2b: Time slots ................................................................................... 13

2c: Program selection ......................................................................... 13

2d: Select music ................................................................................ 13

2e: Save selection ............................................................................. 14

2f: Rename ....................................................................................... 14

3) Musical programming of a weekday (select day: Monday, Tuesday …) .................... 14

3a: Power time .................................................................................. 14

3b: Time slots ................................................................................... 14

3c: Select program ............................................................................ 15

3d: Select music ................................................................................ 15

3e: Save selection ............................................................................. 16

3f: Rename ....................................................................................... 16

II. EVENTS ......................................................................................................... 17

III. MESSAGES .................................................................................................... 19

1) Listen to messages .......................................................................................... 20

2) See scenario ................................................................................................... 20

3) Local messages ............................................................................................... 21

3a: Recording one or several messages ................................................ 21

3b: Consulting recorded messages. ...................................................... 22

4) Open/Close messages ...................................................................................... 24

IV. SETTINGS ..................................................................................................... 26

1) Music volume .................................................................................................. 27

2) Messages volume ............................................................................................ 27

3) Date / Time .................................................................................................... 28

4) Low mode ....................................................................................................... 28

5) LCD Password ................................................................................................. 29

V. MAINTENANCE .............................................................................................. 30

1) Status ............................................................................................................ 31

1a. List of updates ............................................................................. 31

1b. SAS / update ............................................................................... 31

1c: Non used programs ...................................................................... 32

1d: Serial number .............................................................................. 32

1e: Uptime ........................................................................................ 32

1f: More info (memory, capacity, ...) .................................................... 33

2) Expert ............................................................................................................ 33

System password ............................................................................... 33

Updating by DVD-ROM ............................................................................................. 34

Troubleshooting ...................................................................................................... 35

Technical data ......................................................................................................... 35

Introduction

The MultiPlay 7200®, developed by our teams of R&D engineers , is a digital

musical broadcast program player.

The MP7000® is the technological synthesis of 50 years of experience and of

tried and tested know-how.

Of a unique industrial technology, it intelligently

operates 24 hours a day without any human intervention.

Easy to use and immediately operational, it can directly be connected to

all types of sound equipment.

Its sharp programming capacity together with a large storage capacity offer

musicale wealth equivalent to none.

The MultiPlay 7200® allows managing the broadcasting of sound messages

via a network or the Internet.

Although it uses a highly sophisticated development technology, Mood Media

endeavours once again to offer the greatest ease of use.

The program can at any time be selected with the LCD display

and the 5 keys…

The LCD display also allows accessing a wealth of information for parameter

setting or not; the name in progress of being played, the automatic start

and stop of the MultiPlay… everything was designed to offer the most

complete product.

The MP 7200® also allows zoning. Zoning consists in independently

managing 2 or 3 musicale atmospheres from a same equipment.

The musical databank is regularly updated through CD-Rom, DVD-Rom,

network or the Internet.

Safety instructions

IMPORTANT!

Precautions to take before using

First of all observe the instructions below, related to your safety and to the operating safety of your equipment.

To protect oneself

• Never touch the supply cable’s plug with wet hands.

• To remove the plug from the wall socket, never pull on the cable but handle the plug.

On the use of electrical equipment

• Power supply

Plug the power supply cable of the Multiplay 7200® into a wall socket with a correct ground connection to avoid electric shocks. The cable is equipped with a threepin plug to ensure correct grounding of the equipment.

• Overload

Do not use adaptor plugs and do not try to remove the cable’s grounding pin. If you use an extension cable, use a three-wire extension cable equipped with a ground plug.

• Current variations

preferably use a regulated power source to protect the equipment from variations of the electric current.

• Penetration of object or liquids

Do not insert anything in the equipment for it would risk entering in contact with the high voltage circuits or short-circuiting the components and thus provoke a fire or an electric shock or discharge. Never to liquids on the player.

On the emplacement

• Protection of electric cable

Do not put anything on the cables and do not place the cables on a passage axis. Particularly make sure of protecting the connectors, the plugs and the cable’s connection point with the MP 7200® player.

• Ventilation:

The air vents are designed to allow an

appropriate ventilation and to ensure normal operating.

• do not obstruct the air vents,

• avoid placing sheets of paper and flyers

on the equipment,

• Do not place this appliance in a wall recess,

• Keep your appliance far from radiators and other sources of heat.

Unpacking

Check the following accessories:

The Multiplay 7200® player is supplied with 2 cables:

• a black electric cable (A)

• an audio adaptor cable (B)

In case of zoning, the audio adaptor cables (B) are supplied according to the number of zones.

The audio adaptor cable (B) is at RCA standard, the most used for general public amplifiers. If this standard does not correspond to that of your amplifier, use an audio cable adapted to the auxiliary input or tuner of your sound equipment.

Before operating this equipment, please attentively read these user instructions.

The responsibility of MOOD MEDIA cannot be committed in case of eventual damages due to inappropriate use or non compliant with the user manual.

Keep these instructions for further reference.

Description and illustration

Connection to the electric supply network

PRECAUTION

To avoid risks of electrocution, only use the electric cable that was supplied. Plug the cable into the mains socket. Connect the electric plug in a correctly grounded mains socket.

Important Before plugging in, it is imperative to switch off your amplifier (sound

equipment).

MP7200® user instructions 5

AUX or TUNER

Zoning

Connection to your amplifier (1 zone):

a - Connect the audio cable’s plug to the audio output (audio out 1) of your MP7000®. b – Depending on your amplifier, you will find an “AUX” or “TUNER” input on which to connect the MP7000® with the RCA plugs. c – Switch your amplifier on and select “AUX” or “TUNER”.

Connection to several amplifiers (2 or 3 zones):

ATTENTION: For each zone (1,2 or 3), an amplifier and a network of loudspeakers

are needed. There is a through zone audio output. a - Connect the audio cable’s plug in the audio output (audio out 1/2/ or 3) of your MP7200®. b – Depending on your amplifiers, you will find an “AUX” or “TUNER” input on which to connect the MP7200® with the RCA plugs. c – Switch on your amplifiers and select “AUX” or “TUNER”. Repeat the above process for each zone.

Audio out1

for zone 1

Audio out2

for zone 2

Identical cable for each zone

Audio out3

for zone 3

Amplifier

Power plug

Before any handling, the display asks for which zone you wish to set parameters and play music (see page 10).

MP7200® user instructions 6

Switching on

Press the ON/OFF key. The music starts after a few seconds. The default setting of the MP7000® is programmed to switch on automatically at 5:30 a.m. and to switch off at 10:30 p.m.

In case of starting of the MP7000® with the ON/OFF key, the appliance switches off after a few moments if the switching on was done out of the times defined in the "Power Time" (see 1a page 12 or 2a page 14) and no music is played.

Information displayed during the playing of music

At the end of loading, the date and time appear on the 1st line of the LCD display. The performer, the tile and the name of the program scroll across the 2nd line.

On the third line:

To give a message directly, put the mike in position "one" and speak. The icon

representing the mike should appear on the display.

Important: the mike should be connected in “off” position when starting the MP7000®.

shows that the player is playing 1 program.

shows that the player is playing 2 programs.

shows that the player is playing 3 programs.

shows that the MP7000® is operating in hard disc mode.

shows that a CD or DVD is present in the player.

shows that the MP7000® is programmed to start and stop automatically (operating time.)

shows the number of the last update.

If the indicator blinks, it shows that the update sequence is not valid; contact the hotline to obtain the procedure to follow.

MP7200® user instructions 7

Using the display’s keys

The centre key "OK" and the arrow direction keys: ◄/▲/▼/► allow accessing the various menus and functions of the Multiplay 7200®.

Pressing:

►: Name stopped!: allows going to the next

name (on all the zones).

◄: Control out 1/2/or 3: allows checking what

music is played (on each zone).

▲ -------------#--: allows setting the volume. ▼

OK: validates an action and accesses the menus.

Important: When you press the directions keys, give the system the time to record your order.

Stopping the MP 7200®

Use the ON/OFF key

The MP 7200® is designed to operate in a continuous manner. You can thus leave it on-line.

Comment: In the "MUSIC" menu, you can set the "Power Time". The MP 7200® will switch off automatically at the end of playing time that that you entered in parameters and will switch on again automatically the next day at the preset time. See the "MUSIC" menu page 12 (1a) or page 14 (2a).

The serial number

The serial number is located under the Multiplay 7200®.

MP7200® user instructions 8

Menu functions of the MP 7200®

The MultiPlay 7200® proposes a range of functions allowing you to personalize it according to your needs. These functions are gathered in menus and submenus.

List of the menu’s functions

I. MUSIC

1) Selection of the day: Immediately

2) Choice of the day: Every day a) Power Time b) Time slot c) Selection of the program d) Selection of the music e) Save the selection f) Renaming g) Exit

3) Selection of the day: Monday,

Tuesday, Wednesday…

a) Power Time b) Time slot c) Selection of the program d) Selection of the music e) Save the selection f) Rename g) Exit

II. EVENTS

a) Selection of the music b) Frequency c) Start of the event d) End of the event e) Time slot

III. MESSAGES

1) Listen to messages Selection of the message

2) See scenario List of messages

3) Local messages a) Selecting the message b) Selecting the action

4) Open/close messages a) Selection of the day b) Time slot c) Closing at noon? d) Exit

5) Exit the menu

IV. SETTINGS

1) The music’s volume

2) Volume of messages

3) Date/time

4) Soft mode a) Selection of the day b) Time of reduced volume c) Exit

5) LCD Password

6) Exit the menu

V. MAINTENANCE

1) Status a) List of updates and update

via the SAS b) Non used programs c) Serial number d) Uptime e) More info… f) Exit the menu

2) Expert

3) Exit the menu

Each menu has its own submenu and its own functions.

Accessing a menu function

1. Press the central "OK" key to access the "MUSIC" menu or if you are playing on

several zones, proceed at first as indicated page 13.

2. Press any direction key ◄/▲/▼/►, to access the following menus: "EVENTS" or

"MESSAGES" or "SETTINGS" or "MAINTENANCE".

3. Press the "OK" key to validate your selection.

4. With the direction keys ◄/▲/▼/►, scroll the display to the desired function and press

"OK" to access it.

5. Parameter, select or adjust the function with the direction keys ◄/▲/▼/►.

6. Press the centre "OK key to confirm.

MP7200® user instructions 9

Selection of the zone

When your appliance is in zoning mode, that is to say it plays different musicale atmospheres on several zones, before any handling the display asks, the zone to parameter.

Press the central "OK" key.

The display shows "Audio choice - Zone 1".

With the direction keys ◄/▲/▼/►, select the desired zone.

For example, zone 2.

Press the central "OK" key to confirm the zone.

The display then shows "Music – GO!" you can start your various parameter setting in this zone. Refer to the "MUSIC" menu on the following page.

Important: When you make a direct announcement with the microphone, the message is played on all the zones. As well as the setting of the sound’s volume (music and messages) is the same on all the zones. On the other hand, the pre-recorded or personal messages can have different parameters from one zone to another.

Comment: If a quaver flickers on the display, it shows you are in zone 1.

When you have two or three quavers, the quaver that flickers represents the zone in which you are setting parameters. For example, for 3 zones, if you work on zone 2, the second quaver, present on the display will flicker.

11/08/2003 18:32 MOODMEDIA2006 © ……..

Audio selection Zone 1

Audio selection Zone 2

Music < > GO!

MP7200® user instructions 10

I. MUSIC

This menu allows:

 Selecting and instantly playing a musical program.  Creating an identical musical scenario every day of the week per time slots.  Selecting the broadcasting times.  Selecting and broadcasting a different musical scenario every day of the week.

“MUSIC” menu flowchart

MUSIC

Selection of the day: Immediately

Selection of the day: Every day

Power Time Time slot Selection of program Selection of music Save selection Rename Exit

Selection of the day: Monday, Tuesday, Wednesday…

Power Time Time slot Selection of program Selection of music Save selection Rename Exit

How to access the "MUSIC" menu?

1) Press the central "OK" key.

How to access its functions?

2) Press any direction key ◄/▲/▼/►, up to the desired function: "DAY’S

SELECTION: EVERY DAY" or "SELECT DAY: MONDAY, TUESDAY, WEDNESDAY…"

3) Press the central "OK" key to confirm the function.

Comment: To help you in programming your Mp7200® according to your field of

activity, you have about twenty programs pre-designed by our sound designers. These programs are recognizable in the music menu classified under P.XX (e.g.: P. Topaz – P. Quartz…) In the case of pre-designed programs, it is not necessary to manage the time slots; everything is automatic. By selecting a pre-designed program, the loading time before broadcasting can be superior to 2 minutes. You can find all the pre-designed programs on the following Internet site:

http://music.moodmedia.fr/mp7200.html

MP7200® user instructions 11

1) Immediate broadcast of a program (Select day: immediately)

This function allows selecting and immediately broadcasting a program. This programming is only valid during the period defined in the "Power Time" i.e. the times of beginning and end of broadcasting. When the appliance restarts, it takes up the scenario that you have previously established.

a) Press the central "OK" key. The display shows "Music". Press "OK" again to access

Music < > GO!

this menu.

b) The display shows "Select day - Immediately". Press “OK” again to access this submenu.

Select day Immediately

c) The display then shows "Select program" Select the desired program with the

arrow keys ◄/▲/▼/►.

d) Press the central "OK" key

Select program _

to confirm the musical program. The music restarts immediately with your selection.

e) The display returns to its normal level:

Select program Classic

date, time and title in progress of broadcasting

Important: When you press the arrow keys, please give the system the time to record your order.

11/08/2003 18:32 MOODMEDIA2006 © …zone

2) Musical programming of a whole week (Select day: Every day)

This function allows selecting and broadcasting different programs according to the time of day. This selection remains valid every day of the week during the broadcasting time (Power time).

Steps 1 + 2 + 3 (page 11)

2a: Power time

= to define the parameters of the timetable of beginning and of end of

Select day Every day

broadcasting.

The display shows "Power time".

If you wish to modify this schedule,

Power time 10:30 – 22:30

use the arrow keys:

◄ and ► (left/right): to position the

cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase or reduce

the hours and minutes. When the broadcasting timetable is defined, press "OK" to confirm.

Power time 09:30 – 21:30

MP7200® user instructions 12

2b: Time slots

The default setting of the 1st time slot corresponds to Power Time. The time slots are not limited and are automatically inserted in relation to the previous one. By reducing the end of broadcasting value, a 2nd time slot is automatically created and so on. E.g.: power time = 09:00 – 20:00 --> 09:00 – 18:00 – 18:00 / 20:00

The display then shows "Time slot

- 09:30 – 21:30".

If you do not want several time slots

Time slot 09:30 – 21:30

(you will thus broadcast a single program), press "OK". The display then shows: "Select program " (see 2c).

If you wish to broadcast different musical

Time slot 09:30 – 11:30

atmospheres according to the time of day, you can divide the slot into ranges. Use the arrow keys:

◄ and ► (right/left): to position

the cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase

or decrease the hours and minutes. Confirm by pressing "OK".

After having selected the program(s) of the 9:30 – 11:30 schedule, a new schedule will automatically be proposed. Here, 11:30 – 21:30. 11:30 = end previous time slot 21:30 = end of broadcast (Power Time)

2c: Program selection = to select a pre-defined sequence.

Select program _

The display then shows "Select program". With the arrow keys ◄/▲/▼/► select the program or the pre-defined program for this time slot. Confirm by pressing "OK".

Select program P. Restaurant

Or if you wish to select several programs at the same time, refer to 2d.

Programs beginning with a P. are programs pre-defined by Mood Media.

The display then shows "Select day - Exit". Confirm by pressing "OK".

The 2nd time slot appears taking the previous modifications into account.

Select day Exit

use the arrow keys once again to modify the slot. Confirm by pressing "OK".

The display again shows "Select program". Renew the above procedure or if you wish to

Time slot 11:30 – 12:15

create your own sequence, i.e. selecting several programs at the same time, refer to 2d.

2d: Select music

Select music _

= to create one’s own musical scenario

The display shows "Select music". With the arrow keys ◄/▲/▼/► select a program.

Select music Ambiance

The display again shows "Select music". Select another program that will be broadcasted after the previous one. When you have finished your selection, confirm "Select music- _" to exit

Select music VIP

MP7200® user instructions 13

by pressing "OK".

Here, a title of the "Atmosphere" program will be followed by a title of the "VIP" program and again “Atmosphere” at the 11:30 – 12:15 time slot.

Select music _

Renew the procedure, for all the time slots that you wish to create.

2e: Save selection = to save your scenario.

After having validated the last time slot, the display shows "Save selection" Press "OK" again to validate.

Save selection New P

Your selection is saved.

2f: Rename

= to name the program that you have created.

The display shows "Rename – New P".

Rename Morning

You name your selection, by using the arrow keys:

▲ and ▼ (up/down): to scroll through the letters.

◄ and ► (left/right): to move the cursor

Select day

Exit

toward the left or right. Confirm by pressing "OK".

The display then shows "Select day – Exit". Confirm by pressing "OK".

Important: When you press the arrow keys, give the system the time to record your order

The music restarts with your selection.

3) Musical programming of a weekday (select day: Monday, Tuesday …)

This function allows selecting and broadcasting different programs, according to an accurate time of the day. This selection is valid on that day during the broadcasting time (Power time).

Steps 1 + 2 + 3 (page 11)

With the arrow keys ◄/▲/▼/► select the day of the day of the week that you want to set. For example: Monday.

Select day Monday

3a: Power time

= to define the parameters of the timetable of beginning and of end of broadcasting.

Power time 09:30 – 22:30

The display shows "Power Time".

If you wish to modify the time slot, use the arrow keys:

◄ and ► (left/right): to position

the cursor on the hour and minutes.

▲ and ▼ (up/down): to increase or decrease

Power time 09:00 – 20:30

the hours and minutes. When the broadcasting timetable is defined, press "OK" to confirm

3b: Time slots

MP7200® user instructions 14

= to divide the defined slot (Power time) into several moments of the day.

The display then shows "Time slot

Time slot 09:00 – 20:30

- 09:00 – 20:30".

If you do not want several time slots (you will thus broadcast a same program), press "OK". The display then shows: "Select program " (see 3c).

Time slot 09:00 – 11:45

If you want to broadcast different musical atmospheres according to the time of day, you can divide the slot into ranges. Use the arrow keys:

◄ and ► (right/left) to position

the cursor on the hour and minutes.

▲ and ▼ (up/down) to increase

or decrease the hours and minutes. Confirm by pressing "OK".

After having selected the program(s) of the 9:30h – 11:45 time range, a new time range will automatically be proposed. Here, 11:45 – 20:30. 11h45 = end of the previous time slot 20h30 = end of broadcasting (Power

3c: Select program = to select a pre-defined sequence.

Select program Restaurant P.

The display then shows "Select program". With the arrow keys ◄/▲/▼/► select the pre-defined sequence for the time slot. Confirm by pressing "OK".

Programs beginning with P. are programs pre-defined by Mood Media.

The display then shows "Select day - Exit". Confirm by pressing "OK".

The 2nd time slot appears taking the previous

Select day Exit

modifications into account. Use the arrow keys again to modify the slot. Confirm by pressing "OK".

The display again shows "Select program". Renew the above procedure or if you wish to

Time slot 11:30 – 12:30

create your own sequence, refer to 3d.

3d: Select music

= to create one’s own musical scenario

Select music _

The display shows "Select music". With the arrow keys ◄/▲/▼/► select a program. The display again shows "Select music". Select another program that will be played after the previously chosen one. When you have finished your selection, confirm "Select music- _" to exit by pressing "OK".

Here, a title of the “Atmosphere” program will be followed by a title of the "VIP" program and again “Atmosphere”… in the 11:30 – 12:30 time slot.

Renew the procedure, for all of the time slots that you wish to create.

Select music Atmosphere

Select music VIP

Select music _

MP7200® user instructions 15

3e: Save selection = to save your scenario.

After having validated the last time slot, the display shows "Save selection" Press "OK" again to validate. Your selection is saved.

3f: Rename

= to name the program that you just created.

The display shows "Rename – New P.". You name your selection, by using the arrow keys:

▲ and ▼ (up/down): to make the letters scroll.

◄ and ► (left/right): to move the cursor

toward the left or right. Confirm by pressing "OK".

The display then shows "Select day – Exit". Confirm by pressing "OK". The music restarts with your selection.

Save selection New P.

Rename Morning

Select day

Exit

Important: When you press the arrow keys, give the system the time to record your order.

MP7200® user instructions 16

II. EVENTS

This menu allows:

 selecting a specific program and choosing its broadcasting frequency.  defining the parameters of the broadcast during a chosen period of time and a

time slot.

Flowchart of the "EVENTS" menu

EVENTS

Select music

Frequency

Beginning of the event

End of the event

Time slot

How to access the "EVENTS" menu?

1) Press the central "OK" key.

2) The “MUSIC” menu is displayed on the screen. Press once the ► arrow key. The

display shows "EVENTS".

3) Press the central "OK" key to validate your selection.

MP7200® user instructions 17

a) The display shows "Events - GO". Press "OK" to access this menu.

b) The display then shows "Select music".

Events < > GO!

Select the desired program with the arrow keys ◄/▲/▼/►. For example, a Christmas program. Press "OK" to validate.

Select music Christmas

c) The display shows "Frequency – XX%". With the arrow keys ◄/▲/▼/► select the frequency at which a title of the specific program will be broadcast.

Frequency 20%

For example, 20%: a title of the program, that you have just chosen, will be broadcast every 5 titles. Press "OK" to validate.

d) The display shows " Beginning event". You select the date and the time at which you wish to start the broadcasting of the

Start event 10/12/2006 09:30

specific program, with the arrow keys:

▲ and ▼ (up/down): to increase or decrease

the hour and minutes or the date.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

e) The display shows " End event" You select the date and time at which you wish to end broadcasting the specific

End event 18/12/2006 20:30

program, using the arrow keys:

▲ and ▼ (up/down): to increase or decrease

the hour and the minutes or the date.

◄ and ► (left/right): to move the cursor

toward the left or right. Confirm by pressing "OK".

f) The display shows "Time slot". You set the time slot of the day during which you wish to broadcast

Time slot 08:00 21:00

the specific program, with the arrow keys:

▲ and ▼: to increase or decrease

the hour and minutes.

◄ and ► (left/right): to move the cursor

toward the left or the right. For example, only in the morning. Confirm by pressing "OK".

e) The display then shows "Select music". Select the dash (-) and press "OK" if you want to exit the menu.

If you wish to set the parameters of the same program over another period and/or at a different frequency or another program, restart the procedures from a).

For example, for the Christmas period, you can set the parameters of several dates and several broadcasting frequencies, up to 100% of the titles at Christmas time.

Time slot 08:00 12:00

Select music _

MP7200® user instructions 18

III. MESSAGES

This menu allows:

 Listening to a message via the internal speaker, without interrupting the

broadcasting on the loudspeakers network.

 Consulting the broadcasting scenario of sound messages (out of personal messages).  Recording one’s own messages with a mike and scheduling them.  Setting the parameters of pre-recorded messages opening / closing.

Flowchart of the "MESSAGES" menu

MESSAGES

Listen to messages

Select message

See scenario

List of messages

Local messages

Selecting a message Selecting the action

Open/close messages

Select day Time slot Closing at noon? Exit

Exit menu

How to access the "MESSAGES" menu?

1) Press the central "OK" key.

2) The "MUSIC" menu is displayed on the screen. Press twice the ► arrow key. The

display shows "MESSAGES". Press the central "OK" key to validate your selection.

How to access its functions?

3) Press any arrow key ◄/▲/▼/►, up to the desired function: "LISTEN TO MESSAGES" or

"SEE SCENARIO" or "LOCAL MESSAGES" or "OPEN/CLOSE MESSAGES" or "EXIT MENU".

4) Press the central "OK" key to confirmer the function.

How to exit the "MESSAGES" menu?

5) Press any arrow key ◄/▲/▼/►, up to "EXIT MENU", validate by pressing the central

“OK” key. The music restarts with your selection and the LCD display returns to its normal level: date, time, and title being broadcasted.

MP7200® user instructions 19

1) Listen to messages

This function allows listening, with the internal speaker, to messages found on the appliance without interrupting the broadcasting.

Steps 1 + 2 (page 19)

a) The display shows "Listen to messages – GO".

Listen to messages

< > GO!

Press the central "OK" key to access this submenu.

b) The display then shows "Select.message – _". With the arrow keys ◄/▲/▼/►

Select.message

select the message that you wish to listen to. Press the central "OK" key to confirm. You can listen to the message instantly without interrupting the music and without

Select.message Fr_open

broadcasting the message.

Here, you will hear an opening message in French.

c) To exit "Select.message", select the dash (-).

Select.message

Press the central "OK" key to validate. The display shows "Listen to messages – GO". With the arrow keys ◄/▲/▼/►

select another function or pass on to step 5 (page 19).

Listen to messages

< > GO!

2) See scenario

This function allows consulting the list of messages and their broadcasting timetable.

Steps 1 + 2 + 3 (page 19)

a) The display shows "Listen to messages – GO".

b) With the ► arrow key select "See scenario". Press the central "OK" key to access this submenu.

c) The display shows "List messages – GO". Press the central "OK" key to validate.

d) The display then shows on what (radio) zone you are on. With the arrow keys ◄/▲/▼/►

select the zone in which you want to consult the list of messages. For only one zone, you can scroll through the timetable and the messages with the ► arrow key.

To exit "List messages" press the central "OK" key. The display shows "See scenario" With the arrow keys ◄/▲/▼/►

select another function or pass on to step 5 (page 19).

Listen to messages

< > GO!

See scenario

< > GO!

List messages

< > GO!

List messages

Msg RADIO 1

List messages

08:30 open_mp3

See scenario

< > GO!

MP7200® user instructions 20

3) Local messages

This function allows recording, setting the parameters of and broadcasting your own messages.

Important: the microphone should be connected and in “off” position when starting the MP7200®.

3a: Recording one or several messages

Steps 1 + 2 + 3 (page 19)

a) The display shows "Local messages - GO".

Local messages

< > GO!

Press the central "OK" key to access this submenu.

b) The display shows "Select message – _". With the arrow keys ◄/▲/▼/►

Select message

select the zone in which you want to record the message(s) and the (Local) sound track. For example, Zone 2 Local 1. "Local of 1 at X" is defined at the installation and represents the number of messages that you can record

Select message

Zone2Local1_

in a specific zone. Press the central "OK" key to validate.

c) If no message was recorded on this track the display shows "No message - [OK]".

No message

[OK]

If a message is recorded, please refer to 3b.

If you are ready to record, press "OK". The display shows "Select action – Save message". Press "OK" once again.

Select action Save message

(If you are not ready, select "Select action – Do nothing" with the

► arrow key, and "OK", the display returns to b).

d) Otherwise the display shows "Start recording

Start recording [START]

- [START]". Press the central "OK" key. If your mike is in the “ON” position, the display shows "Recording". If your mike is not in the “ON” position, the display shows "Use Mike ON/OFF". When your mike is in the “ON” position,

Recording

you can speak in the microphone. When your message is finished, switch off your microphone. The message will be played to listen to, via the internal speaker, without interrupting the broadcasting in progress.

Select action Record again

The display shows "Select action – Record again", that allows rerecording the message if it does not suit you. The display then returns to "Start recording - [START]".

Select action Message OK

Redo the procedure at d).

e) If you are not satisfied with your message, Press the ► arrow key once The display shows "Select action – Message OK". Confirm by pressing "OK".

Select action Listen to msg

MP7200® user instructions 21

f) The display then shows " Select action - Listen to msg". Press "OK" to hear the message again. g) With the arrow keys ◄/▲/▼/►

you can select several actions that you validate by pressing "OK":

• "Do nothing": the message is simply recorded.

• "Play the message": plays it immediately.

• "Do not play": the message is not played.

Or stop broadcasting

• "Erase": suppression of the message

• "plays /5 min": broadcasting the message every

5 minutes.

• "plays / 10 min": broadcasts every 10 minutes.

• "plays / 15 min”: broadcasts every 15 minutes.

• "plays / 20 min": broadcasts every 20 minutes.

• "plays / 30 min": broadcasts every 30 minutes.

• "plays / 60 min": broadcasts every hour.

Comment: the message does not cut the music being played, it is inserted between two titles.

• "Start broadcasting": setting of the date and

time to start playing the message created.

• "End broadcasting": setting of the date and time to end playing the message created.

With the arrow keys, change:

▲ and ▼ (up/down): to increase or decrease

the hour and the minutes or the date.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

• "Rename": to change the name. To rename your message, use the arrow keys:

▲ and ▼ (up/down): to faire scroll the letters and

figures.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

The display shows "Local messages – GO!" With the arrow keys ◄/▲/▼/► select another function or pass on to step 5 (page 22).

3b: Consulting recorded messages.

Steps 1 + 2 + 3 (page 19)

a) The display shows "Local messages - GO". Press the central "OK" key to access this submenu.

b) The display shows "Select message – _". With the arrow keys ◄/▲/▼/►

Select action Do nothing

Select action plays / 30 min

Select action Begin broadcasting

Start broadcasting 21/06/2006 09:00

Select action End playing

End broadcasting 30/06/2006 23:53

Select action Rename

Rename Zone2Local1

Rename Promo Juillet

Local messages

< > GO!

Select message

MP7200® user instructions 22

select the message you wish to consult.

For example, "July special offer".

Press the central "OK" key to validate.

c) The display then shows the length of the message.

Here, the recording length is 22 seconds.

Press the central "OK" key.

d) The display then shows the broadcasting frequency. Here, the message will be played every 30 minutes. Press the central "OK" key.

e) The display then shows "Select action - Listen to msg". Press "OK" to listen to the message again.

f) With the arrow keys ◄/▲/▼/► you can select several actions that you

validate by pressing "OK":

• "Play message": immediate broadcast.

• "Do not play": the message is not broadcast.

• "Erase": suppression of the message.

• "Begin broadcasting": consultation of the date

and time of beginning of broadcasting and possibility of modifying it.

• "End broadcasting": consultation of the date and

time of end of broadcasting and possibility of modifying it. You can modify the dates and timetable

with the arrow keys:

▲ and ▼ (up/down): to increase or decrease

the hour and the minutes or the date.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

• "Rename": to change the name. To rename your message, use the arrow keys:

▲ and ▼ (up/down): to scroll the letters

and the figures.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

• "Do nothing": simply to consult the

parameters of the message. Press "OK".

The display then shows "Select message – _". With the arrow keys ◄/▲/▼/► select another message or pass on to step 5 (page 19).

Select message

July special offer

Time length: 22 s

[OK]

Every 30 min [OK]

Select action Listen to msg

Select action Play message

Select action

Erase

Select action End broadcasting

End broadcasting 12/07/2006 23:53

Select action Rename

Rename Extend special offer

Select action

Do nothing

Select action

MP7200® user instructions 23

4) Open/Close messages

This function allows adjusting the opening and closing messages according to your daily timetable of morning, noon and evening.

Messages: Pre-opening will be broadcast 10 minutes before the opening, Opening will be broadcast 2 minutes after the opening … and Closing will be broadcast 5 minutes before closing.

-Steps 1 + 2 (page 19)

a) The display shows "Open/Close Msg - GO".

Open/Close Msg

< > GO!

Press the central "OK" key to access this submenu.

b) The display shows "Select day - every day".

Select day

every day

If your opening and closing timetables are the same every day of the week, validate by pressing "OK". If your timetables vary, see the next page.

Time slot

08:30 – 19:30

c) The display shows "Time slot". To set the parameters of your opening and closing timetable, use the arrow keys:

◄ and ► (left/right): to move

the cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase

or decrease the hours and minutes. Confirm by pressing "OK".

d) "Close at noon? - YES [NO]" is then displayed.

If you do not close at noon, select [NO], with the arrow keys  The display then shows "Select day – exit". Press "OK" to exit the submenu.

If you close at noon, select [YES], with the arrow keys  The display then shows "Time slot".

To set the parameters of your opening and closing timetable and opening at noon, use the arrow keys:

 and .



 and .



Time slot

09:00 – 20:00

Close at noon? YES [NO]

Close at noon? [YES] NO

Time slot

12:30 – 14:00

◄ and ► (left/right): to move

the cursor on the hour and the minutes.

▲ and ▼ (up/down) to increase

or decrease the hours and minutes. Confirm by pressing "OK". The display then shows "Select day – Exit". Confirm by pressing "OK". With the arrow keys ◄/▲/▼/► select a function or pass to step 5 (page 19).

Time slot

12:00 – 13:30

Here, a closing message is broadcast around 11:55. And a pre-opening message at 13:32.

MP7200® user instructions 24

opening at 13

:32.

If your opening and closing timetables are not the same every day of the week, follow the procedure below:

Steps 1 + 2 (page 19)

a) The display shows "Open/Close Msg - GO". Press the central "OK" key to access this submenu.

b) The display shows " Select day - every day". With the arrow keys ◄/▲/▼/► select the day that you wish to set the parameters of. Press the central "OK" to confirmer.

c) The display shows "Time slot". To set your opening and closing timetable use the arrow keys:

◄ and ► (left/right): to position

the cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase

or decrease the hours and minutes. Confirm by pressing "OK".

d) "Close at noon? - YES [NO]" is then displayed.

If you do not close at noon, select [NO], with the arrow keys 

 and .



The display then shows "Select day – exit". press "OK" to exit the submenu.

If you close at noon, select [YES], with the arrow keys 

 and .



The display then shows "Time slot".

To set your noontime opening and closing timetable, use the arrow keys:

 and  (right/left): to move

the cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase

or decrease the hours and minutes.

Confirm by pressing "OK".

Renew the procedure for each day of the week for which you wish to set the parameters.

Select day Exit

Open/Close Msg

< > GO!

Select day

every day

Select day

Monday

Time slot

08:30 – 19:30

Time slot

09:00 – 20:00

Close at noon? YES [NO]

Close at noon? [YES] NO

Time slot

12:30 – 14:00

Time slot

12:00 – 13:30

Here, a closing message will be broadcast at about 11h55. And a preopening message at 13 :20 and of

Select day Exit

MP7200® user instructions 25

IV. SETTINGS

This menu allows:

 Setting the sound volume of the music and messages.  Setting the system date and time.  Automatically reduce the system’s sound volume for example at night.  Locking the use of the appliance with a password.

Flowchart of the "SETTINGS" menu

SETTINGS

Music volume

Messages volume

Date/time

Low mode

Select day Soft volume time Exit

LCD Password

Exit the menu

How to access the "SETTINGS" menu?

1) Press the central "OK" key.

2) The “MUSIC” menu is displayed on the screen. Press three times the ► arrow

key. The display shows "SETTINGS". Press the central "OK" key to validate your selection.

How to access its functions?

3) Press any arrow key ◄/▲/▼/►, up to the wanted function: "MUSIC VOLUME" or

"MESSAGES VOLUME" or "DATE/TIME" or "LOW MODE" or "LCD PASSWORD" or "EXIT".

4) Press the central "OK" key to confirm the function.

How to exit the "SETTINGS" menu?

5) Press any arrow key ◄/▲/▼/►, up to "EXIT THE MENU", validate by pressing the

central "OK" key. The music restarts with your selection and the LCD display comes back to its normal state: date, time, and title being broadcast.

MP7200® user instructions 26

1) Music volume

This function allows of setting the general volume of the MP7200®.

Steps 1 + 2 (page 26)

a) The display shows "Volume music - GO". Press the central "OK" key to reach this submenu.

Music volume

< > GO!

b) The display shows a dashed line on which a # is found. The arrow key  (up) serves to increase the volume. The arrow key  (down) serves to lower the volume.

Volume saved

< > GO!

Press the central "OK" key to confirm.

c) The display shows "Volume saved". Press the central "OK" key to validate.

d) The display shows "Messages volume". Press the central "OK" key to reach

Messages volume

< > GO!

this submenu or pass on to step 5 (page 26).

2) Messages volume

This function allows of setting the volume of messages in relation to the music.

Steps 1 + 2 + 3 (page 26)

a) The display shows "Volume messages - GO". Press the central "OK" key to reach this submenu.

Messages volume

< > GO!

b) The display shows a dashed line on which a # is found. The arrow key  (up) serves to increase the volume of messages. The arrow key  (down) serves to lower the

Volume saved

< > GO!

Volume of messages. Press the central "OK" key to confirm.

c) The display shows "Volume saved". Press the central "OK" key to validate.

d) The display shows "Date/Time". Press the central "OK" key to reach

Date/Time

< > GO!

this submenu or pass on to step 5 (page 26).

Comment: if you want to increase the sound volume of messages in relation to the music, select, for example:

MP7200® user instructions 27

---------------#--------- music volume

------------------------#- messages volume

3) Date / Time

This function allows setting the time and of modifying the date.

Steps 1 + 2 + 3 (page 26)

a) The display shows "Date/Time - GO".

Date/Time

< > GO!

Press the central "OK" key to reach this submenu.

Setting the present date and time, with the keys arrow:

Date/Time

13/06/2006 18:42

▲ and ▼ (up/ down): to scroll through the figures

of hours, minutes or the date.

◄ and ► (left/right): to move the cursor toward

the left or the right. Confirm by pressing "OK".

b) The display shows "Low mode". Press the central "OK" key to reach this submenu or pass to step 5 (page 26)

4) Low mode

This function allows lowering the sound volume of the music in a time slot and setting parameters according to the day of the week.

Steps 1 + 2 + 3 (page 26).

a) The display shows "Low mode - GO". Press the central "OK" key to reach this submenu.

b) The display shows "Select day - every day". If you wish to reduce the volume automatically every day at the same time, press "OK"

c) The display shows "Reduced volume T.". To set the time parameters of start and end of the low mode, use the arrow keys:

Low mode

< > GO!

Low mode

< > GO!

Select day

every day

Reduced volume T.

20:30 – 07:30

◄ and ► (left/right): to position

the cursor on the hour and the minutes.

▲ and ▼ (up/down): to increase

or decrease the hours and minutes. Confirm by pressing "OK".

d) The display shows "Select day - every day".

If you wish to use the low mode in another time slot on a chosen day, select it with

the arrow keys ◄/▲/▼/►. and repeat the procedure indicated in c).

Otherwise select "Select day – exit" to exit the low mode.

e) The display shows "LCD Password – GO". Press the central "OK" key to reach this submenu or pass to step 5 (page 26).

Select day

every day

Select day

Wednesday

Reduced volume T.

19:30 – 09:30

Select day

exit

MP7200® user instructions 28

5) LCD Password

This function allows locking your appliance with a password that will be requested before any handling.

Steps 1 + 2 + 3 (page 26)

a) The display shows "LCD Password - GO". Press the central "OK" key to reach

LCD Password

< > GO!

this submenu.

b) Create your password with the arrow keys:

▲ and ▼ (up/down): to scroll through the figures

LCD Password

and/or the letters.

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

LCD Password

CT12

c) The display shows "Exit menu - GO". Press the central "OK" key to validate. the display returns to its normal state: date, time, and title of the music broadcasted.

Exit menu

< > GO!

The password is now needed to be able to open the menus.

It will be requested at any handling.

If you forget your password, the display shows "System password?".

Call the hotline

When the MP7200® is password protected, and that you want to open the menus, press the central "OK" key. The display shows "Password?- _".

Enter your password with the arrow keys:

▲ and ▼ (up/down): to scroll through the figures

and/or the letters.

Password?

◄ and ► (left/right): to move the cursor

toward the left or the right. Confirm by pressing "OK".

To suppress or modify a password, do the following:

The display shows "LCD Password –XXXXX". Here, for example "LCD Password – CT12". With the arrow keys  and , Place the cursor on the last letter or the last figure (here, on the 2). And with the arrow keys  and , select the underline (_). Continue the procedure for the previous letter or figure till there is nothing but the underline (_). Press "OK" to validate.

The password is now suppressed.

To modify it, select other letters or figures in place of the underline (_) or restart the procedure described at the top of this page in 5).

Music

< > GO!

LCD Password

CT12

LCD Password

CT1_

LCD Password

MP7200® user instructions 29

V. MAINTENANCE

This menu allows:

 Consulting the list of updates.  Erasing non used or outdated programs.  Consulting information relative to the appliance.

Flowchart of the "MAINTENANCE" menu

MAINTENANCE

Status

List of updates and updating via the SAS Programs not used Serial number Uptime More info… Exit menu

Expert

System password?

Exit menu

Remarks on the ‘MAINTENANCE" menu Some functions of this menu only serve for consulting information. No value can be modified. This information is only used for diagnostics procedures and remote on-line maintenance.

How to access the "MAINTENANCE" menu?

1) Press the central "OK" key.

2) Le menu "MUSIC" menu is displayed on the screen. Press four times the ►

direction key. The display shows "MAINTENANCE". Press the central "OK" key to validate your selection.

How to access its functions?

3) Press any direction key ◄/▲/▼/►, up to the desired function: "STATUS" or

"EXPERT" or "EXIT MENU".

4) Press the central "OK" key to confirm the function.

MP7200® user instructions 30

1) Status

1a. List of updates

= to consulter the list of updates that were already made. If an update is missing, the figure at the lower right of the display flickers. The list will indicate what update is missing.

Steps 1 + 2 (page 30)

a) The display shows "Status - GO". Press the central "OK" key to reach

Status

< > GO!

this submenu.

b) The display shows "List of updates - GO". Press the central "OK" key to access this function.

List of updates

< > GO!

c) With the arrow keys ◄/▲/▼/► consult the list. Press the central "OK" key.

List of updates

MAJ00000_

d) The display shows "SAS/update" To consulter this function, press "OK". Otherwise, with the arrow keys  and  (left/right), select another function.

1b. SAS / update

= to update via the SAS, when your MP7200® is connected to a SAS (Internet or intranet).

Steps 1 + 2 + 3 + 4 (page 30)

a) The display shows "List of updates - GO". Press twice the key central "OK" key.

SAS/update

_ GO!

b) The display shows "SAS/update". To consulter this submenu, press "OK".

c) The display then shows "SAS/update -

[Abort]".

SAS/update

[Abort]

With the arrow keys  and ,

select [Confirm]. The music stops during the update.

d) The display shows "SAS Update – Please wait".

SAS/update

[Confirm]

The music restarts after a few moments.

SAS/Update

Please wait

MP7200® user instructions 31

1c: Non used programs

= to suppress programs. Comment: You can only suppress the programs that you created yourself and that are not presently used in the music menu.

Steps 1 + 2 + 3 + 4 (page 30)

a) The display shows "List updates - GO".

Non used prog.

< > GO!

With the arrow keys  and ,

select "Non used prog. - GO". Press the central "OK" key.

b) The display shows "Program to erase - _".

Program to erase

With the arrow keys ◄/▲/▼/►

select the program you wish to suppress. Validate by pressing "OK". The program is definitively suppressed.

Program to erase

Morning

c) The display again shows "Program to erase - _". Renew the procedure, if you wish to erase another program. To exit this function, select the underline (_) and press "OK".

Program to erase

d) The display shows "Serial number" To consulter this function, press "OK". Otherwise, with the arrow keys  and  (left/right), select another function.

1d: Serial number

= to consult the machine’s serial number (essential for identification when connecting via the SAS).

Steps 1 + 2 + 3 + 4 (page 30)

a) The display shows "List of updates - GO". With the arrow keys

Serial number

< > GO!

 and  (left/right), select "Serial number" Press the central "OK" key to consult the number. Press "OK" again.

b) The display shows "Uptime". To consulter this function, press "OK". Otherwise, with the arrow keys

Serial number

0070300066

 and  (left/right), select another function.

1e: Uptime

= to consulter the time elapsed since the last system reboot.

Steps 1 + 2 + 3 + 4 (page 30)

The display shows "List of updates - GO". With the arrow keys

Uptime

< > GO!

 and  (left/right), select "Uptime" Press the central "OK" key to Consult the time elapsed since the last reboot.

Uptime

Up 57 min

MP7200® user instructions 32

b) The display shows "More info". To consult this function, press "OK". Otherwise, with the arrow keys  and  (left/right), select another function.

1f: More info (memory, capacity, ...)

This information is only useful for diagnostics purposes of online maintenance.

2) Expert

System password

= to define, at the installation

 the system language.  the number of zones.  the number of messages to record per zone (Local).  the network parameters.  identification in relation to SAS.

This password is known by Mood Media.

MP7200® user instructions 33

Updating by DVD-ROM

Periodically, an update CD or DVD will be sent to you. These CD or DVD are identified by a number.

It is imperative to do the updates following the numbering order of the DVD.

The number of the last update is displayed at the bottom right of the LCD screen. If the order of updates was not respected, the indicator flashes; this means that the update sequence is not valid; contact the hotline to obtain the procedure to follow.

• Open the player.

• Insert the CD or DVD printed side upward.

• Close the player. The update runs automatically (the music is cut off).

• At the end of the update, the display shows “Update #XX – OK to eject the CD”.

• Press the central « OK » fey. The display shows “Remove the CD – restart in a few s.”.

• The player opens. Remove the CD or DVD.

The player closes again automatically,

the machine is reinitialised and the music starts again after about thirty seconds.

Concerning DVD-ROMs:

The DVD-ROM (Digital Versatile Disc – Read Only Memory) is a CD-ROM variant with a greatly storage capacity.

Handling CD-ROMS and DVD-ROMS

• To remove a CD from its box, press the centre of the box, and lift the CD by holding it with care on the sides.

• So that CDs remain clean, handle them with care. Never touch the surface.

• Do not paste paper or adhesive tape on CDs.

• Do not expose CDs to direct sunlight, to sources of heat or to excessive dampness.

• Never use chemical products such as aerosols for discs or antistatic liquids or solvents to

clean CDs.

• The CDs should be stored in their box after use so as to avoid serious scratches.

WARNING: This appliance was designed to read only DVD-ROMs made by Mood Media. Never insert other DVD-ROMs.

MP7200® user instructions 34

Troubleshooting

Power supply

The player is not on-line:

 Check if the power supply cable is

correctly connected.

 Check the connections.  Check that the amplifier is on-line and

that audio in is correctly selected.

 Unplug the mains plug for 1 or

2 minutes and plug in again.

Power cut

The broadcast of your musical program as soon as the power supply is reestablished.

Sound / Audio

Absence of sound or bad sound quality:

 Check the connections between the

MP7000® and your amplifier.

 Check that the amplifier is on-line and

that audio in is correctly selected.

 Check the operating time

configuration (Power Time).

 If the connection cable is damaged,

replace it.

 Restart the player with the ON/OFF

button.

 Check the connections and the

settings of speakers.

 Control the volume button.

After these checks, if there is still no sound, call the Mood Media customer department.

Update

Update interrupted:

Remove the DVD-ROM and restart the procedure.

Update error:

The DVD-ROM is ejected if the update was already done.

DVD-ROM

DVD-ROM non ejected:

Check that the DVD-ROM is positioned printed side upward. Renew the procedure.

Technical data

Voltage:

200 to 240 volts (V) ~ 3 A 50 / 60 hertz (Hz)

Wattage:

60 Watts.

Audio features

Output level: 0 db Output impedance: 600 Ohms Bandwidth: 20 Hz – 18 kHz (+/- 0.5 db) Signal-to-noise ratio: ≅ 80 db (20 Hz – 18

kHz)

Dimensions

Overall dimensions:

Height:

57 mm

Length:

435 mm

Width:

280 mm

Dimensions for integrating in furniture

Height: 57 mm

Length:

435 mm + 20 mm on each side (ventilation) = 475 mm.

Width: 280 mm + 50 mm at rear (ventilation and connections) + 130 mm in front (player trap) = 460 mm.

The MP7000® can be inserted in a 19” rack with brackets (not supplied).

Weight:

4.5 Kg

5.5 Kg packaging included

Environment

Temperature:

Operation: 10° to 35° Celsius (C) (50° to 95° Fahrenheit [F])

Storage – 40° to 65°C (– 40° to 149°F)

Relative humidity:

20 to 80% (no condensation)

MP7200® user instructions 35

MOOD MEDIA

Rd 307

78810 Feucherolles

France

hotline@moodmedia.fr

MP7200® user instructions 36

Mood Media MULTIPLAY 7200 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual