MOOD Lia H40B Instruction Manual

Before using this sewing machine, please always read and follow all the basic safety instructions to prevent possible damages.

1. An appliance should never be left unattended when the power is turned on.

2. Always switch off this appliance immediately after using or before cleaning.

3. The sewing machine is equipped with a LED lamp. If the LED lamp is broken, please consult the manufacturer or an authorized dealer to replace it. Please do not attempt to replace it by yourself to prevent any hurt.

1. Read the instruction carefully before using the machine

2. Keep the instructions at a suitable place close to the machine and hand it over when you give the machine to a third party.

3. Do not use outdoors or in humid environments. If your hand is wet, please do not use the machine to prevent electric shock.

4. Never leave the machine unattended. Children or elderly people could wrongly operate the machine and get damaged.

5. Children aged above 8-year-old, people with reduced physical, sensory or mental capabilities, or beginners should be attended with a capable supervisor to operate this machine. Safety instructions should be followed to prevent any hazards.

6. This machine is not a toy. Children shall not play with it unattendedly.

7. Cleaning or machine maintenance shall not be made by children without supervision.

8. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

9. Always use the proper needle plate. The wrong plate can cause the needle to break.

10. Do not use bent needles.

11. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

12. Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual (pull power plug).

13. Never drop or insert any object into any opening.

14. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

DANGER

WARNING

- To reduce the risk of electric shock:

- To reduce the risk of burns, fire, electric shock, or injury to

persons:

Important safety instructions

15. If the LED lamp is damaged or broken, it must be replaced by the manufacturer or its service agent or a similarly qualified person, in order to avoid a hazard.

16. Never place anything on the foot controller.

17. Never operate the appliance with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth.

18. The machine may only be used with foot controller type C-9000.

19. If the supply cord fixed with foot controller is damaged, it must be replaced by the manufacturer or its authorized service agent or a similar qualified person in order to avoid a hazard.

20. Do not dispose of electrical appliances as unsorted municipal waste. Please use separate collection facilities or contact your local government for information regarding the available collection systems.

This sewing machine is intended for household use only.

SAVE THESE INSTRUCTIONS

GETTING READY TO SEW

SEWING BASICS

Contents

Principal parts of the machine ...............................................................................................................6

Accessories ...........................................................................................................................................7

Connecting the machine........................................................................................................................8

Winding the bobbin...........................................................................................................................9-10

Inserting the bobbin .............................................................................................................................11

Threading the upper thread............................................................................................................12-13

Using the needle threader ...................................................................................................................14

Replacing the needle...........................................................................................................................16

Changing the presser foot ...................................................................................................................18

Type of presser foot chart....................................................................................................................19

Two-step presser foot lifter ..................................................................................................................20

To raise or drop the feed dogs .............................................................................................................20

Normal mode ..................................................................................................................................................21

mode.................................................................................................................................................22

Adjusting presser foot pressure...........................................................................................................15

Information on the LCD Display .....................................................................................................21-24

Buttons of the machine........................................................................................................................23

Operation buttons...........................................................................................................................24-26

Function buttons.............................................................................................................................27-29

Memory

Needle, Fabric, Thread Selection Guide..............................................................................................17

Pattern chart...................................................................................................................................30-31

Selecting stitch ...............................................................................................................................35-36

Thread tension.....................................................................................................................................32

Useful skills.....................................................................................................................................33-34

Straight stitches and needle position...................................................................................................37

Zigzag stitches.....................................................................................................................................37

Stretch stitch........................................................................................................................................38

Overcasting stitches ............................................................................................................................39

Reverse ..........................................................................................................................................................33

Free arm .........................................................................................................................................................33

Sewing corners ...............................................................................................................................................33

Cutting the thread ...........................................................................................................................................34

Sewing on the heavy fabric.............................................................................................................................34

Using the overcasting foot ..............................................................................................................................39

Using the all purpose foot ...............................................................................................................................39

ORDINARY SEWING

Blind hem/ lingerie stitch......................................................................................................................40

Buttonhole stitch.............................................................................................................................41-44

Darning stitch .................................................................................................................................48-49

Zipper insertion...............................................................................................................................50-51

Narrow hemming .................................................................................................................................52

Cording ................................................................................................................................................53

Satin stitch sewing...............................................................................................................................54

Gathering.............................................................................................................................................55

Smocking.............................................................................................................................................56

Free motion darning, embroidery and monogramming ..................................................................57-58

Quilting ...........................................................................................................................................59-60

Fagoting...............................................................................................................................................61

Scallop stitch .......................................................................................................................................62

Walking foot.........................................................................................................................................63

Mirror ...................................................................................................................................................64

Memory...........................................................................................................................................68-72

Making a buttonhole on stretch fabrics ...........................................................................................................44

inserting a centered zipper .............................................................................................................................50

Inserting a side zipper.....................................................................................................................................51

Single cording .................................................................................................................................................53

Triple cording ..................................................................................................................................................53

Darning ...........................................................................................................................................................57

Embroidery .....................................................................................................................................................58

Monogramming...............................................................................................................................................58

Attaching the edge/ quilting guide...................................................................................................................59

Joining the pieces of the fabric .......................................................................................................................59

..............................................................................................................................................60

Scallop hem ....................................................................................................................................................62

Scallop edging ................................................................................................................................................62

Combining patterns.........................................................................................................................................68

Editing patterns...............................................................................................................................................70

Clearing patterns ............................................................................................................................................71

Adding patterns...............................................................................................................................................71

Recalling and sewing the memorized pattern.................................................................................................72

Bar tack stitch ......................................................................................................................................45

Eyelet Stitch.........................................................................................................................................46

Button sewing ......................................................................................................................................47

Elongation............................................................................................................................................65

Using the twin needle .....................................................................................................................66-67

Patchwork stitch

APPENDIX

Warning functions...........................................................................................................................73-74

Buzzer sound.......................................................................................................................................75

Maintenance...................................................................................................................................76-77

...................................................................................................................78-79

Warning message...........................................................................................................................................73

Warning sound................................................................................................................................................74

Cleaning the LCD screen................................................................................................................................76

Cleaning the sewing machine surface ............................................................................................................76

Cleaning the hook...........................................................................................................................................76

Trouble shooting guide

GETTING READY TO SEW

Face plate

Buttonhole lever

Auto needle threader

Needle plate cover

Sewing table and accessory box

Thread cutter

Operation buttons

Speed limiting adjustment dial

Function buttons

LCD screen

Selection buttons

Foot controller connector

Power switch

Power cord

Handle

Presser foot lifter

Drop feed lever

Bobbin thread guide

Tension dial

Upper thread guide

Presser foot pressure

Horizontal spool pin

Hole for second

spool pin

Bobbin winder spindle

Bobbin winder stopper

Principal parts of the machine

Hand wheel

Top cover

GETTING READY TO SEW

Standard

Optional

1. All purpose foot (T)

2. Zipper foot (I)

3. Buttonhole foot (D)

4. Overcasting foot (E)

5. Blind hem foot (F)

6. Satin stitch foot (A)

7. Button sewing foot (H)

8. Bobbin (3x)

10. Spool holder (Large)

11. Spool holder (Small)

12. Spool pin felt

13. Second spool pin

14. Needle (3x)

15. Brush/ Seam ripper

16. Screwdriver (L & S)

17. Soft cover

18. Hemmer foot (K)

19. Cording foot (M)

20. Quilting foot (P)

21. Darning/ Embroidery foot

22. Gathering foot

23. Twin needle

24. Walking foot

Edge/quilting guide

006900008

006813008

006916008

006016008

006917008

0061850081

006020008

123

006905008

006907008

006014148

TA10943209

006015009

R60033209

006904008

006914008

006008001

006172008 006H1B0001

006012008

006099008

H1D0083892

Accessories

006H1D0003

006D1E0004

GETTING READY TO SEW

Before connecting the power supply, make sure that the voltage and frequency shown

Place the machine on a stable table.

1. Connect the power line cord to the machine by inserting the 2-hole plug into the

2. Connect the power line plug to the wall outlet.

3. Turn on the power switch.

4. The sewing lamp will light up when the switch is turned on.

on the rating plate is conforming with your mains power.

mains

plug socket.

Caution:

Always make sure that the machine is unplugged from power source and the main switch is on ("O") when the machine is not in use and before inserting or removing parts.

Polarized plug information

This appliance has a polarized plug (one blade wider than the other) to reduce the risk of electrical shock; this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

Foot Control

When the sewing machine is turned off, insert the foot control plug into its connector on the sewing machine.

Turn on the sewing machine, and then slowly depress the foot control to start sewing. Release the foot control to stop the sewing machine.

Consult a qualified electrician for how to connect the machine to the power source. The appliance must be used with the correct foot controller C-9000.

Attention:

Connecting the machine

Note:

If using a special thread which winds quickly off the spool, attach a net to the spool before using or use a larger spool holder instead. Reduce the thread tension if necessary.

GETTING READY TO SEW

1. Place the thread and spool holder onto the spool pin. For smaller spools of thread, place spool holder with the small

side next to the spool or use the small spool holder.

4. Wind the thread clockwise around the bobbin winder tension discs.

5. Place the thread end through one of the inner holes in the bobbin as illustrated. Then fix this empty bobbin onto the spindle.

2. Pull the thread from the spool and make sure the thread is properly snapped into the upper thread guide.

3. Guide the thread through the left thread guide then continue to pull the thread until reach the pre-tension spring as illustrated.

Winding the bobbin

6. Push the bobbin to the right side.

GETTING READY TO SEW

10.After the bobbin has wound a few rounds, stop the machine and cut the extra thread. Keep it short and near the hole of the bobbin then continue to fill the bobbin until it is 80~90% full.

Once the bobbin is full, release the foot pedal or push the button to stop the machine then push the bobbin winder spindle to left.

11.Cut the extra thread then remove the bobbin from the spindle.

Note:

When the bobbin winder spindle is set on the right position, machine cannot perform sewing application and the hand wheel will not turn. To start sewing, please remember to push the bobbin winder spindle to its left position.

8. Hold the thread end securely in one hand.

9. Depress the foot controller or push the Start/Stop button to start winding the bobbin.

7. When the bobbin winder spindle is pushed to the right position, a message icon will be shown on the LCD screen. When this message appears, users can only wind the bobbin thread as described in below sections.

This message will disappear when the bobbin winder spindle is pushed back to the left side for normal sewing.

Sewing cannot be done while

the spindle is set at the right side position.

GETTING READY TO SEW

Pull the thread through the slit under the finger (A).

Attention:

Turn power switch to off ("O") before threading or unthreading the machine.

The thread take-up lever must be in the highest position when threading.

To open the bobbin cover, push the latch to the right side.

Then Insert the bobbin in the bobbin holder with the thread in counter-clockwise direction (arrow mark).

To make sure that the thread is pulled into the tension spring of the bobbin holder, press a finger slightly onto the bobbin while pulling. As a check you must feel a resistance in the thread feed. Follow the arrow marking on the stitch plate and guide the thread from (A) to (B).

Then continue to follow the arrow marking and guide the thread from (B) to (C).

To cut the excess part of the thread, pull the thread back over the blade at point (C).

Close the bobbin cover.

Inserting the bobbin

GETTING READY TO SEW

Please Note:

It is very important to do the threading correctly. Improper threading may result in different sewing problems.

Start by raising the needle to its highest point, and also raise the presser foot to release the tension discs.

1. Lift up the spool pin. Place the spool of thread on the spool

pin so that the thread comes from the front of the spool, then place the spool cap at the end of the spool pin.

Threading the upper thread

GETTING READY TO SEW

5. Then pull the thread further down and around the bottom part

of the take up lever cover.

6. At the top of this movement, pass the thread from right to the

left through the slotted eye of the take-up lever and then downwards again.

7. Snap the thread into the down thread guide and guide the

thread through the wire loop. Pull the end of the thread through the needle from front to

rear, and pull out about 10 cm of thread. Use the needle threader to thread the needle. (See the next

page for instruction.)

4. Pull the thread forward and down. This operation pulls the

thread into the thread tension.

3. Guide the thread around another thread guide. Snap the

thread into it then pull the thread through the pre-tension

2. Pull the thread from the spool and snap the thread into the

upper thread guide.

GETTING READY TO SEW

The needle threader automatically turns to the threading position and the hook pin passes through the needle eye.

Pull the thread to the right, guiding it to the front of the needle.

Hold the thread loosely and release the lever slowly.

The hook will turn and pass the thread through the needle eye forming a loop.

Pull the thread through the needle eye.

Please raise the needle to its highest position and lower down the presser foot.

Lower the needle threader lever slowing and pull the thread through the thread guide as illustrated and then to the right.

Attention:

Turn power switch to the off position ("O").

Using the needle threader

GETTING READY TO SEW

Adjusting presser foot pressure

The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of fabric (light-or-heavy weight).

However, if you need to adjust the presser foot pressure, turn the presser adjusting screw with a coin.

For sewing very heavy fabric, loosen the pressure by turning the screw counterclockwise, and for thin fabric, tighten by turning it clockwise.

To return to machine's default pressure setting, turn the screw to make it flush with the face cover.

Change the needle regularly, especially if it is showing signs of wear and causing problems.

Insert the needle following the illustrated instructions.

A. Loosen the needle clamp screw and tighten

again after inserting the new needle. The flat side of the shaft should be towards the back.

B. Insert the needle as far up as it will go.

Needles must be in perfect condition.

Problems can occur with:

- Bent needles

- Blunt needles

- Damaged points

Attention:

Turn power switch to off ("O") when carrying out the below operation!

GETTING READY TO SEW

Replacing the needle

Medium weight fabrics: cotton, satin, kettle cloth, sailcloth, double knits, lightweight woolens.

GETTING READY TO SEW

Heavy duty thread, carpet thread.

16 (100)

NEEDLE, FABRIC, THREAD SELECTION GUIDE

11-14 (80-90)

Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.

Heavyweight fabrics-canvas, woolens, outdoor tent and quilted fabrics, denims, upholstery material (light to medium).

14 (90)

18 (110)

NEEDLE SIZE FABRICS

THREAD

9-11 (70-80)

Lightweight fabrics-thin cottons, voile, serge, silk, muslin, Qiana, interlocks, cotton knits, tricot, jerseys, crepes, woven polyester, shirt & blouse fabrics.

Light-duty thread in cotton, nylon, polyester or cotton wrapped polyester.

Most threads sold are medium size and suitable for these fabrics and needle sizes.

Use polyester threads on synthetic materials and cotton on natural woven fabrics for best results.

Always use the same thread on top and bottom.

Please Note:

- In general, fine threads and needles are used for sewing fine fabrics, and thicker threads are used for sewing heavy fabrics.

- Always test thread and needle size on a small piece of fabric which will be used for actual sewing.

- Use the same thread for needle and bobbin.

- Use a backing for fine or stretchy fabrics.

Needle, Fabric, Thread Selection Guide

Heavy woolens, overcoat fabrics, upholstery fabrics, some leathers and vinyls.

GETTING READY TO SEW

Changing the presser foot

Turn power switch to off ("O") when carrying out any of the below operations!

Raise the presser foot bar (a). Attach the presser foot holder (b) as illustrated.

Lower the presser foot holder (b) until the cut-out (c) is directly above the pin (d).

Press the (e). Lower the presser foot holder (b) and the presser foot (f) will

engage automatically.

Raise the presser foot. Press the black lever (e) and the foot will disengages.

Attach the guide (g) in the slot as illustrated. Adjust according to need for hems, pleats, etc.

Attention:

Attaching the presser foot holder

Attaching the presser foot

Removing the presser foot

Attaching the guide

black lever

edge/quilting

GETTING READY TO SEW

Overcasting foot (E)

Overcasting

Darning Free embroidery Monogramming

All purpose foot (T)

Zipper foot (I)

Button sewing foot

APPLICATIONPRESSER FOOT

General sewing, Patchwork stitches, Decorative stitching, Smocking, Fagoting, etc.

PRESSER FOOT APPLICATION

Inserting zippers

Blind hem foot (F)

Blind hem stitching

Satin stitch sewing

Button sewing

Satin stitch foot (A)

NEEDLE NEEDLE

Hemmer foot (K)

(Optional)

Narrow hemming

Gathering foot

(Optional)

Gathering

Quilting foot (P)

(Optional)

Quilting

Cording foot (M)

(Optional)

Cording

Walking foot

(Optional)

This foot helps to prevent uneven feeding of very difficult fabrics

Buttonhole sewing, Bar tack stitches, Darning stitches.

Buttonhole foot (D)

Darning/ Embroidery foot

(Optional)

Type of presser foot chart

GETTING READY TO SEW

To raise or drop the feed dogs

The presser foot lifter raises and lowers your presser foot.

With the sewing table off the machine, the feed dog adjustment lever can be seen on the base in back of the sewing machine.

Sliding the lever to the " " (b) will lower the feed dog, for example during button sewing. If you wish to continue sewing normally, slide the lever to the " " (a) in order to raise the feed dogs.

The feed dog if you do not turn the hand wheel, even if the lever is slid to the right. Make a complete turn to raise the feed dogs.

will not rise up

The needle must always be raised at the highest position.

Note:

When sewing multi-layers or thick fabrics, the presser foot can be further raised up for easy re-positioning your sewing work.

Two-step presser foot lifter

GETTING READY TO SEW

Information on the LCD Display

1. Pattern

2. Pattern number

3. Reverse

4. Auto-lock

5. Suggested presser foot

6. Tension

7. Pattern group

8. Needle up position

9. Stitch length

10. Needle position

11. Sound on

12. Auto-stop

13. Mirror 14 Twin needle

15. Needle down position

16. Stitch width

17. Sound off

18.

19.

Alphabet number Alphabet

1. Pattern

2. Pattern number

3. Pattern group

4. Current page

5. Total page

6. Operation indication

Normal mode display

Normal mode display pattern browser display

Normal mode

GETTING READY TO SEW

1. Selection frame

3. Empty m

4. C

5. Pattern number and pattern

6. Auto-stop

7. Mirror

8. Needle up position

9. Sound on

10.

11. Stitch width

12. Stitch length

13. C attern group

14. C

15.

16. ursor

Memory module with unit

emory module

urrent memory module

urrent p

urrent memory unit Total of memory units Memory c

Elongation

1. Pattern

2. Pattern number

3. Memory model

4. Pattern group

5. Current page

6. Total page

7. Operation indication

Memory mode display

Memory mode display pattern browser display

Memory mode

GETTING READY TO SEW

Buttons of the machine

8. Direct pattern selection and number buttons

10.

11.

12.

13.

14.

15. Clear button

Start/stop button Reverse button Auto-lock button Needle up/down position button Speed limiting adjustment dial

6. OK button Arrow buttons

Mirror button Elongation button Twin needle button Stitch length adjustment button Stitch width adjustment button Memory button

16. Pattern group selection button

GETTING READY TO SEW

Operation buttons

Start/stop button

The machine will start running when Start/stop button is pressed and will stop when pressed the second time. The machine will rotate slowly at the beginning of the sewing.

Reverse button

Keep pressing the button to do reverse sewing. An icon " " will appear on the LCD display to indicate reverse sewing. Release the button: Back to normal forward sewing direction. Only the Direct Patterns 1-5 and A Group Pattern 00 can be sewn in reverse. If you press the reverse button before starting to sew, the machine will permanently sew in reverse until you press the button again.

Auto-lock button

If the Direct Patterns 1-4 or A Group Pattern 00 were selected, the machine will immediately sew 3 locking stitches when the Auto-lock button is pressed, then machine will automatically stop.

The LCD screen will display the figure " " until the machine is stopped.

Select the pattern (except Direct Patterns 0-4 and A Group Pattern 00, 86-98), press the Auto-lock button, the machine will sew 3 locking stitches at the end of the current pattern and automatically stop.

The LCD display will display the figure " " until the machine is stopped.

The function will be cancelled if you press the button once again or select another pattern.

GETTING READY TO SEW

Needle up/ down position button

Press the button to decide whether the needle should stop at the upper position or stay in the material when you stop sewing.

Press the button so the arrow on the LCD points upward " " the needle moves to the highest position and will stop there after sewing.

Press the button so the arrow on the LCD points downwards " " the needle moves to the lowest position and will stop there after sewing.

Please Note:

During sewing, press the needle up/down button will stop the machine automatically.

Speed adjustment dial

Speed adjustment dial can control the sewing speed.

Turn the dial clockwise to increase the sewing speed. Turn the dial counterclockwise to decrease the sewing speed.

Arrow buttons

Use the buttons to select desired pattern, function... etc.

OK button

Press this button to confirm the selection. In the normal/ memory mode, press the button

to enter the pattern browser.

GETTING READY TO SEW

Direct pattern selection and number buttons

Direct pattern selection

Press the buttons to select the utility patterns shown beside the number button when the mode button is set at the Direct mode.

Number buttons

Except the Direct pattern mode, the other mode can be selected by pressing the desired numbers.

Press the number buttons for selecting the pattern needed.

For example: pattern 36

GETTING READY TO SEW

Function buttons

Mirror button

Except the Direct Pattern 0 and the patterns 86-98 from the Group Patterns "A", the other patterns can be mirror imaged by pressing the mirror button.

The machine will continue to sew the reflected pattern until the mirror button is pressed again. The mirror function also will be cancel if the pattern changed.

A. Normal pattern B. Mirror patternimage

Elongation button

A Group Patterns 13-36 can be elongated up to five times than its normal length by pressing the elongation button.

When the width or length or stitch is changed, a greater variety of patterns are available.

Twin needle button

Except the Direct Pattern 0 and the patterns 86-98 from Group Patterns "A", the other patterns can be sewn in two parallel line of the same stitch with the twin needle.

Press the twin needle button, and the machine automatically reduces the maximum width for the twin needle sewing.

Press the button again to return to single needle sewing.

GETTING READY TO SEW

Stitch length adjustment button

When you select a stitch pattern, the recommended stitch length will be used and its number will be shown on the LCD screen for user's reference.

The stitch length can be further adjusted by pressing the stitch length adjustment button. To shorten the stitch length, press the "–" button (left). For a longer stitch length, press the "+" button (right). The stitch length can be adjusted between "0.0-4.5". Certain stitches will have a limited stitch length.

Stitch width adjustment button

When you select a stitch pattern, the recommended stitch width will be used and its number will be shown on the LCD screen for user's reference.

The stitch width can be adjusted by pressing the stitch width adjustment button. For a narrower stitch width, press the left side of the button. For a wider stitch, press the right side of the button. The stitch width can be adjusted between "0.0-

7.0". Certain stitches will have a limited stitch width.

When Direct Patterns 1-4 and A Group Pattern 00 are selected, this button can be used for adjusting the needle position. Press the left side of the button will move the needle to the left position. Press the right side of the button will move the needle to the right position. The numbers will be changed from left position "0.0" to extreme right position "7.0". The preset center needle position will be indicated as "3.5".

GETTING READY TO SEW

Pattern group selection button

The LCD screen will be set at direct patterns mode when you turn on the machine.

Press the pattern group selection button, LCD screen enters the pattern group selection screen automatically. Use the arrow buttons to select the desired group of stitch.

Direct patterns mode.

A Group Patterns mode.

B Group Patterns mode.

Block style alphabet mode.

Script style alphabet mode.

Clear button

If an incorrect pattern or memory module is selected, press this button to clear it or return to the previous screen.

Memory button

Press the memory button to enter the memory mode. Users can store the various combinations of characters or stitches.

The Direct mode patterns and the patterns 86-98 from Group Patterns "A" cannot be memorized.

SEWING BASICS

Direct patterns

A Group Patterns

B Group Patterns

Pattern chart

A Block stylelphabet -

A Script style alphabet - lphabet

SEWING BASICS

- Default thread tension setting: "4"

- To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down.

- Proper tension setting is important for good sewing quality.

- For all decorative sewing, you will always obtain a nicer stitch and less fabric puckering when the upper thread appears on the bottom side of your fabric.

- There is no single tension setting which is appropriate for all the stitches and fabrics.

Thread tension is too loose for straight stitch sewing. Turn dial to higher number.

Thread tension is too tight for straight stitch sewing. Turn dial to lower number.

Normal thread tension for zigzag and decorative stitches.

Normal thread tension for straight stitch sewing.

Upper thread

Bobbin thread

Surface

Reverse side

Tight

Loose

Thread tension

SEWING BASICS

Free-arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.

Reverse stitching is used to secure the threads at the beginning and at the end of a seam.

Press the reverse button and sew 4-5 stitches. The machine will sew forward when the button

is released.

Reverse

Free arm

1. Stop the sewing machine when you reach a corner.

2. Lower the needle into the fabric manually or by pressing the needle up/ down button once.

3. Raise the presser foot.

4. Use the needle as a pivot and turn the fabric.

5. Lower the presser foot and resume sewing.

Sewing corners

Useful skills

SEWING BASICS

The black button on the left side of the presser foot will lock the presser foot in a horizontal position if you push it in before lowering the presser foot. This ensures even feeding at the beginning of a seam and helps when sewing multiple layers of fabric such as sewing over seams when hemming jeans.

When you reach the point of an increased thickness, lower the needle and raise the presser foot. Press the toe of the foot and push in the black button, then lower the foot and continue sewing.

The black button releases automatically after sewing few stitches.

You also can place another piece of fabric with the same thickness at the back of the seam.

Or support the presser foot while feeding by hand and sewing toward the folded side.

Sewing on the heavy fabric

Cutting the thread

The thread cutter serves two purposes.

1. Cut the thread after threading the needle

2. Cut the thread after finishing a seam.

To cut the thread after completing your work raise the presser foot.

Remove the fabric, draw the threads to the left side of the face cover and cut using the thread cutter.

The threads are cut at the proper length to start the next seam.

Cardboard or

thick fabric

SEWING BASICS

Ten of the most frequently used utility stitches can quickly be selected with the d

. Select the desired stitch from those shown on the top cover.

irect pattern

selection and number buttons

4. Use the arrow buttons to select the

desired group of stitch that you wish. (E.g. For pattern group "A")

3. Press the pattern group selection button

to enter the pattern group selection screen.

The following 5 category icons show on.

5. Press ok button to into pattern browser,

the screen containing the various stitches in the selected pattern group appears.

1. Turn on the sewing machine.

2. When the sewing machine is turned on, the

straight stitch (center needle position) is automatically selected.

Selecting stitch

SEWING BASICS

Use the number buttons

6. Select the desired pattern that you sew.

Press until the stitch that you wish to use is selected.

To the previous/ next stitch pattern.

To the previous/ next stitch pattern row.

ress

the arrow buttons

the arrow button twice, and then press the arrow button once.

For example: Direct pattern 11, p

Please Note:

Press the OK utton can return to theb pattern browser display.

Please Note:

Press the OK utton can return to theb pattern browser display.

Press the number buttons for selecting the pattern needed.

For example: pattern 36

Press the OK button , the stitch pattern is selected.

Use the arrow buttons

0.0 2.0 3.5 5.0 7.0

0.5 1.0 2.0

3.0

4.5

Changing the needle position

These setting apply only to 1-4 and

The pre-set position is "3.5", center position. Press the stitch width adjustment button left " ", the needle position will move to the left.

Press the stitch width adjustment button right " ", the needle position will move to the right.

Direct Patterns

A Group Pattern 00.

....

Changing the stitch length

To shorten the stitch length, press the stitch length adjustment button left " ". For a longer stitch length, press the stitch length adjustment button right " ".

Generally speaking, the thicker the fabric, thread and needle, the longer the stitch should be.

A-00

Zigzag stitches

Adjusting the stitch width

The width increases as you press the stitch width adjustment button from "0.0-7.0".

The width can be reduced on any patterns.

Adjusting the stitch length

The density of zigzag stitches increase as the setting of stitch length approaches "0.3".

Neat zigzag stitches are usually achieved at "1.0-2.5".

Closed up zigzag stitches (close together) are referred to as a satin stitch.

0.0 1.0 3.0 5.0 7.0

0.5 1.0

2.0

3.0 4.5

SEWING BASICS

Straight stitches and needle position

SEWING BASICS

It assures you of a stitch that is strong and flexible and will give with the fabric without breaking. Good for easy to ravel and knit fabrics. It is good for joining durable fabric such as denims.

These stitches can also be used as a decorative top stitch.

Triple zigzag stretch stitch is suitable for firm fabrics like denim, poplin, duck, etc.

Straight stretch stitch is used to add triple reinforcement to stretch and hardwearing seams.

Straight stretch stitch

Straight stitch

Stretch stitch

SEWING BASICS

Change the presser foot to the all purpose foot (T).

Sewing the overcasting along the edge of the fabric so that the needle drops over the edge of the fabric on the right side.

Using the all purpose foot

Change the presser foot to the overcasting foot (E).

Sew the fabric with the fabric edge against the guide of the overcasting foot.

Attention:

The overcasting foot should be used to sew with Direct Patterns 5 and 8 only and do not set the stitch width narrower than "5.0".

It is possible that needle could hit the presser foot and break when sewing other patterns and width.

5.02.0~3.0

2.5~5.02.0-3.0

6 A-02

Using the overcasting foot

Sewing overcasting stitches along the edges of fabric to prevent them from fraying.

Overcasting stitches

ORDINARY SEWING

Fold the fabric as illustrated with the reverse side uppermost.

First carry out an overcasting stitch as shown in left picture.

Place the fabric under the foot. Turn the hand wheel forwards by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the stitch width accordingly.

Adjust the guide (b) by turning the knob (a) so that the guide just rests against the fold.

Sew slowly, guiding the fabric carefully along the edge of the guide.

Turn over the fabric.

Please Note:

It takes practice to sew blind hem. Always make a sewing test first.

5mm

Reverse

side

Reverse

side

Overcasting

stitch

5mm

2.5~4.01.0~2.0

A-03

A-04

9 : Blind hem/ lingerie for firm fabrics

A-03 : Blind hem for stretch fabrics

A-04 : Blind hem for stretch fabrics

Secure the bottoms of skirts and pants with a blind hem, this stitch will sew without stitches showing on right side of fabric.

Reverse

side

Right

side

Blind Hem

ORDINARY SEWING

Buttonhole stitch

Mark the positions of the buttonhole on the fabric. The maximum buttonhole length is 3cm (1 3/16 inch). (Total of diameter + thickness of button.)

Attach the buttonhole foot, then pull out the button holder plate and insert the button.

The size of the buttonhole is determined by the button inserted in the button plate.

The thread should be passed through the hole in the presser foot, then be placed under the foot.

Please Note:

Before sewing a buttonhole on your project, practice on a scrap piece of the same type of fabrics.

A-87

A-91

A-92

A-90

A-86 A-88 A-89

2.5~7.00.3~1.0

3.0~7.01.0~2.0

2.5~5.50.3~1.0

5.5~7.00.3~1.0

0 : For thin or medium fabric

A-86 : For thin or medium fabric

A-88 : For horizontal buttonholes on thick

fabrics

A-89 : For thin or medium fabric

A-87 : For suits or overcoats.

A-90 : For thick coats

A-91 : For jeans or trousers

A-92 : For jeans or stretch fabric with a coarse

weave

Buttonhole sewing to match the size of the button is possible. For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole

finish.

ORDINARY SEWING

Please Note:

, the LCD will the to remind you to lower the buttonhole lever.

The buttonhole stitch was selected and the start/stop button was pressed while the buttonhole lever is raised display

warning message

Before sewing, please hold the thread by hand.

Gently feed the fabric by hand. Before stopping, the machine will automatically

sew a reinforcement stitch after the buttonhole is sewn.

Please Note:

Pull the buttonhole lever all the way down and position it behind the bracket on the buttonhole foot.

Select the buttonhole stitch. Adjust the stitch width and the stitch length

to the desired width and density. Position the fabric under the presser foot

with the front end of the buttonhole mark aligned with the center line on the buttonhole foot.

Starting

point

ORDINARY SEWING

Raise the presser foot and cut thread. To sew over same buttonhole, raise the presser

foot (will return to original position). After sewing the buttonhole stitch, raise the

buttonhole lever until it stops.

* Buttonholes are sewn from the front of the presser foot to the back, as shown.

A-87

A-91

A-90

A-92

A-86 A-88 A-89

Please Note:

After finishing, If the stitch other than the buttonhole, bar tack or darning stitch was selected, and the start/stop button was pressed while the buttonhole lever is lowered, the LCD will display a warning message to remind you to raise the buttonhole lever.

ORDINARY SEWING

Cut the center of the buttonhole : be careful not to cut any stitches on either side. Use a pin as a stopper at the bar tack so you do not cut too much.

When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot.

Attach the buttonhole foot and hook the gimp thread onto the back of the presser foot.

Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then temporarily tie them there. Lower the presser foot and start sewing.

Set the stitch width to match the diameter of the gimp thread.

Once sewing is completed, pull the gimp thread gently to remove any slack, then trim off any excess.

Please Note:

It is suggested that you use interfacing on the backside of the fabric.

Making a buttonhole on stretch fabrics

Please Note:

When cutting the buttonhole with the seam ripper, do not place your hands in the cutting direction, otherwise injuries

may occur.

ORDINARY SEWING

Bar tack stitch

Position the fabric so that the needle is 2mm (1/16 inch) in front of the pocket opening, and then lower the presser foot lever.

Pass the upper thread down through the hole in the presser foot. Pull down the buttonhole lever and position behind the bracket on the buttonhole foot. Gently hold the end of the upper thread in your left hand, and start sewing.

Sewing procedure for bar tack is illustrated. This is an example of sewn bar tacks at pocket

corners.

1.0~3.00.4~1.0

A-97

Extend the button holder plate and set to the desire bar tack length.

Adjust the stitch width and stitch length to personalize the stitches.

Bar tack stitch is used to reinforce points subject to strain, such as pocket corners and openings.

Please Note:

It is suggested that you use interfacing on the backside of the fabric.

A-98

2mm

Starting

point

ORDINARY SEWING

Press the "-" or "+" stitch width adjustment to button select the eyelet size.

Size of eyelet. A. Small: 5.0mm (3/16 inch). B. Medium: 6.0mm (15/64 inch). C. Large: 7.0mm (1/4 inch).

Lower the needle into the fabric at the beginning of the stitching, and then lower the presser foot lever.

Once sewing is completed, the machine automatically sews reinforcement stitches, then stops.

5.0 6.0 7.0

A-94

A-94 : Select for sewing eyelets on belts , etc

A-95 : Select for sewing eyelets on belts , etc

A-95

AB C

Eyelet stitches are used for making belt holes and other similar applications.

Make a hole at the center using an eyelet punch.

* Eyelet punch is not included with the

machine.

- When using the eyelet punch, place thick paper

or some other protective sheet under the fabric before punching the hole in the fabric.

- If thin thread is used, the stitching may be

coarse. If this occurs, sew the eyelet twice one on top of the other.

Please Note:

Eyelet stitch

ORDINARY SEWING

Change the presser foot to the button sewing foot.

Position the work under the foot. Place the button in the desired position, lower the foot.

Select zigzag pattern. Adjust the stitch width to "2.5-4.5" according to the distance between the two holes of the button.

Turn the hand wheel to check that the needle goes cleanly into the left and right holes of the button.

For buttons with 4 holes, sew through the front two holes first, push work forward and then sew through the back two holes.

Move the drop feed control to " " to lower the feed dogs.

2.4~4.5

A-96

When you finish the work, move the drop feed control to " " to raise the feed dogs.

Please Note:

Before sewing, press the Auto-lock button to sew reinforcement stitches automatically at the beginning and at the end of the stitch.

If a shank is required (ex. sew on coats or jackets), place a darning needle on top of the button and sew.

Pull end of the upper thread to the wrong side of the fabric, then tie it with the bobbin thread.

Button sewing

ORDINARY SEWING

Darning stitch

Pull the button holder to rear. Set the button guide plate on buttonhole foot to

the desired length.

Baste the upper fabric and the under fabric together.

Select the needle position. Lower the presser foot over the center of the tear.

The size of one darn cycle is variable. However, the maximum stitch length is 2.6cm

(1 inch) and the maximum stitch width is 7mm (9/32 inch).

a. The length of sewing. b. The width of sewing.

Stop

Start

3.5~7.01.0~2.0

A-93

Darning a small hole or a tear before it becomes larger can save a garment. Choose a fine thread in a color as color as close to your garment possible.

ORDINARY SEWING

2mm

Pass the upper thread down through the hole in the presser foot.

Pull down the buttonhole lever. The buttonhole lever is positioned behind the

bracket on the buttonhole foot.

Gently hold the end of the upper thread in your left hand, and then start sewing.

If the sewing range is too big to sew, then we suggest you can sew several times (or cross sew) to get better sewing result.

Darning stitches are sewn from the front of the presser foot to the back, as shown.

Position the fabric so that the needle is 2mm (1/16 inch) in front of the area to be darned, and then lower the presser foot lever.

Please Note:

When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the correct size.

If the fabric does not feed, for example, because it is too thick, increase the stitch length.

Please Note:

ORDINARY SEWING

- Baste the zipper opening on the garment.

- Press open the seam allowance.

Place the zipper face down on the seam allowance with the teeth against the seam line. Baste the zipper tape.

- Attach the zipper foot. Attach the right side of

the presser foot pin to the holder when sewing the left side of the zipper.

- Attach the left side of the presser foot pin to

the presser foot holder when sewing the right side of the zipper.

- Stitching around the zipper.

- Remove the basting and press.

Inserting a centered zipper

Attention:

Zipper foot should be used for sewing width center needle position straight stitch only. It is possible that needle could hit the presser foot and break when sewing other patterns.

5mm

3.51.5~3.0

Wrong

side

Reverse

stitches

Basting

stitching

Basting

stitching

Wrong

side

Please Note:

When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break.

This foot can be set to sew on each side of the zipper, the edge of the foot guides the zipper to ensure straight placement.

Zipper Insertion

ORDINARY SEWING

Inserting a side zipper

- Baste the zipper opening on the garment.

- Fold back to the left seam allowance.

Turn under the right seam allowance to form 3mm fold.

- Attach the zipper foot. Attach the right side of

the presser foot pin to the holder when sewing the left side of the zipper.

Attach the left side of the presser foot pin to the presser foot holder when sewing the right side of the zipper.

- Stitch the left side of zipper from bottom to

top.

- Turn the fabric right side out, stitch across the

lower end and right side of zipper.

- Stop about 5cm (2 inches) from the top of

zipper. Remove the basting and open the zipper. Stitch the remainder of the seam.

5mm

Wrong

side

Reverse

stitches

Basting

stitching

ORDINARY SEWING

Fold edge of fabric over about 3mm, then fold it over again 3mm for about 5cm along the edge of the fabric.

Insert the needle into the fold by rotating the hand wheel toward you, and lower the presser foot. Sew several stitches and raise the presser foot.

Insert the fabric fold into the spiral opening of hemmer foot. Move fabric back and forth until the fold forms a scroll shape.

Lower the presser foot and start sewing slowly guiding the raw edge of the fabric in front of the hemmer foot evenly into the scroll of the foot.

* The hemmer foot accessory is optional. It is not

included with this machine.

3.0~3.51.5~3.0

The hemmer foot is used to stitch the narrow rolled hems usually found on shirt tails, table linens and along the edge of frills.

Narrow hemming

ORDINARY SEWING

Push the sewing thread to the left and insert three cords into the grooves of the foot and pull about 5cm (2 inches) of the cords behind the foot.

Select the desired pattern and adjust the stitch width so that the stitches are just covering the cords. Lower the foot and sew slowly guiding the cords.

Mark the design on the fabric. Insert the cord in the center groove of the cording foot from the right side opening. Pull the cord about 5cm (2 inches) behind the foot.

The grooves under the foot will hold the length of the cord in place while the stitches are being form over the cord.

Select the stitch and adjust the stitch width so that the stitches are just covering the cord. Lower the foot and sew slowly, guiding the cord over the design.

* The accessory is optional. It is not included with this machine.cording foot

6 A-09 A-28

Single cording

Triple cording

Used for embellishing 1 to 3 cords or decorative threads. Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew over three

strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread, fine wool or lily yarn can be used for cording.

Cording

ORDINARY SEWING

Use the satin stitch foot for satin stitching and sewing decorative stitches. This foot has a full indentation on the underside to allowed easy sewing over the thickness of the stitches form by closely spaced zigzag stitches, and even feeding of the fabric.

To tailor the satin or decorative stitch pattern, you may adjust the length and width of the pattern by pressing the stitch length and width adjustment buttons. Experiment with fabric scraps until you get the desired length and width.

When sewing very thin fabrics, it is suggested that you use interfacing on the backside of the fabric.

Please Note:

0.3~2.0

A-15 A-16 A-17 A-18 A-19 A-20 A-21 A-22 A-23 A-24

A-25 A-26 A-27 A-28 A-29

A-30 A-31

A-32

A-33 A-34

A-35 A-36

A-14A-13

2.5~7.0

Satin stitch sewing

ORDINARY SEWING

Gathered fabric

Remove the presser foot holder and attach the gathering foot, lowering the tension setting to below 2.

Suitable for light to medium weight

fabrics.

Place fabric to be gathered under presser foot to the right of the presser foot.

Sew a row of stitching, keeping the raw edge of fabric aligned with the right edge of foot.

The stitches automatically cause the fabric to gather.

To gather and attach gathered fabric in one step

Look closely at the gathering foot to see a slot on the bottom.

When using the slot, you can gather the bottom layer of the fabric while attaching it to a flat top layer, such as the waistband on a dress bodice.

* The Gathering foot accessory is optional. It is

not included with this machine.

Note:

- When testing machine for adjustments to

achieve desired fullness, work with 10" increments of the fabric, trims or elastic. This makes it easier to determine the adjustments and how much change is needed for your project. Always test on your project fabric and on the same grainline as will be used in your finished project.

- Sew slow to medium speed for better fabric

control.

- Remove the presser foot holder and attach

gathering foot.

- Place the fabric to be gathered with right side

up under the foot.

- Place top layer of the fabric right side down in

the slot.

- Guide the two layers as illustrated.

3.54.0

The Gathering Foot is used for gathering fabrics. Ideal for clothing as well as home decor, works best on thin to medium weight fabrics.

Gathering

ORDINARY SEWING

Use the all purpose foot to sew straight lines 1cm (3/8 inch) apart, across the area to be smocked.

Knot the threads along one edge. Pull the bobbin threads and distribute the

gathers evenly. Secure the threads at the other end.

Reduce the tension, if necessary and sew decorative pattern stitches between the straight seams.

Pull out the gathering stitches.

A-08 A-09

The decorative stitch created by stitching or embroidering over gathers is called "smocking".

It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and

elasticity to fabric.

Smocking

ORDINARY SEWING

Remove the presser foot holder, and attach the embroidery foot to the presser foot holder bar.

Press the embroidery foot on firmly from behind with your index finger and tighten the screw.

Move the drop feed control to " " to lower the feed dogs.

First sew around the edges of the hole (to secure the threads). Working from left to right, sew over the hole in a constant and continuous movement. Turn the work by 1/4 and sew over the first stitching moving the work slower over the hole to separate the threads and not form big gaps between the threads.

Free motion darning is accomplished without the sewing machine internal feed system. Movement of the fabric is controlled by the operator. It is necessary to coordinate sewing speed and movement of fabric.

Please Note:

Darning

3.5~5.0

Free motion darning, embroidery and monogramming

ORDINARY SEWING

Select zigzag stitch pattern and adjust the stitch width as desired.

Stitch along the outline of the design by moving the embroidery hoop. Make sure to maintain a constant speed.

Fill in the design working from the outline towards the inside. Keep the stitches close together.

You will get longer stitches by moving the hoop faster and shorter stitches by moving the hoop more slowly.

Secure with a reinforcement stitches at the end by press Auto-lock button.

Select the zigzag stitch pattern and adjust the stitch width as desired. Sew at a constant speed, moving the hoop slowly along the lettering. When the letter is finished. Secure with a reinforcement stitches at the end by press Auto-lock button.

* Embroider hoop is not included with the

machine.

Monogramming

Embroidery

Please Note:

When you finish the work, move the drop feed control to " " to raise the feed dogs.

* The Quilting foot accessory is optional. It is

not included with this machine.

3.51.0~3.0

Insert the edge/quilting guide in the presser foot holder as illustrated and set the space as you desire.

Attaching the edge/ quilting guide

Sew the first row and move over the fabric to sew successive rows with the guide riding along the previous row of stitching.

Note:

When using the quilting foot, only use center needle position stitches to prevent machine damage.

ORDINARY SEWING

Sandwiching batting between the top and bottom layers of fabric is call "Quilting". The top layer is usually formed by multiple geometrically shaped pieces of materials joined together.

Place the two pieces of fabric with the right side together and sew with the straight stitch. Join the pieces of fabric with a seam allowance of 1/4".

Sew with the side of the presser foot aligned with the edge of the fabric.

1/4"

Joining the pieces of the fabric

3.52.5

Quilting

Open the seam allowances and presses it flat.

Patchwork stitching

A-08 A-09A-07

Place the center of the presser foot on the seam line of the joined pieces of fabric and sew over the seam.

ORDINARY SEWING

Fagoting

Thin paper Basting

- Separate the folded edges of the fabric

pieces with a gap of 4mm (1/8 inch) and baste them onto a piece of thin paper or water-soluble stabilizer sheet.

- Align the center of the presser foot with the

center of the two pieces of fabric and begin sewing.

- After sewing, remove the paper.

A-07

Stitching across an open seam is called "fagoting". It is used on blouses and children's clothing. This stitch is more decorative when thicker thread is used.

ORDINARY SEWING

A-11

- Fold the fabric right side together in and sew

along the edge.

- Cut the fabric along the seam leaving an

allowance of 3mm (1/8 inch) for seaming. Notch the allowance.

- Turn the fabric over and push out the curved

seam to the surface and iron it.

- Stitch along the edge of the fabric, marking

sure not to sew directly on the edge of the fabric.

* For better results, apply spray starch onto

the fabric and press with a hot iron before it is sewn.

- Trim along the stitches.

* Be careful not to cut the stitches.

Scallop hem

Scallop edging

A-12 A-20

Wrong side of fabric

The wave-shaped repeating pattern that looks like shells is called "scalloping". It is used on the collars of blouses and to decorate the edges of projects.

Scalloping

ORDINARY SEWING

* The walking foot accessory is optional. It is not included with this

machine.

Always try to sew first without the walking foot accessory which should be used only when necessary.

It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine. Your sewing machine offers excellent stitch quality on a wide range of fabrics from delicate chiffons to multiple layers of denim.

The Walking Foot accessory equalizes the feeding of the upper and lower layers of fabric and improves the matching of plaids, stripes and patterns. It also helps to prevent uneven feeding of very difficult fabrics.

Lift the presser foot lifter to raise the presser foot bar.

Remove the presser foot holder by unscrewing (counterclockwise) the presser bar attaching screw.

Attach the Walking Foot to the machine as follows:

- The arm (a) should fit into above the needle screw and clamp (b).

- Slide the plastic attaching head (c) from your left to right so that it is fitted into the presser foot bar.

- Lower the presser foot bar.

- Replace and tighten (clockwise) the presser bar attaching screw.

- Make sure both the needle screw and the presser bar attaching screw are tightly secured.

Draw the bobbin thread up and place both the bobbin thread and the needle thread behind the walking foot attachment.

Walking foot

ORDINARY SEWING

Please Note:

- Direct Patterns 0 and Patterns 86-98 from Group Pattern "A" cannot be mirror imaged.

- Mirror imaged patterns can also be combined with other patterns.

Select the stitch. Pressing the mirror button .

The LCD screen icon for mirror imaging of the pattern appears.

The machine will continue to sew the reflected pattern until the mirror button is pressed again or the pattern is changed.

A. Normal pattern sewing. B. Mirror pattern sewing.

Mirror

ORDINARY SEWING

0.3~1.0 2.5~7.0

The stitch can be elongated up to five times its normal length by pressing the elongation button .

Press the elongation button. The symbol for elongation appears on the LCD

display. Press the elongation button several times to

adjust the elongation as desired. The machine will continue to sew the displayed

pattern until the elongation button is pressed again or the pattern is changed.

When the width or length or stitch is changed, a greater variety of patterns are available.

Please Note:

A Group Patterns 13-36 can be elongated and mirrored simultaneously.

Elongation

A-15 A-16 A-17 A-18 A-19 A-20 A-21 A-22 A-23 A-24

A-25 A-26 A-27 A-28 A-29

A-30 A-31

A-32

A-33

A-34 A-35 A-36

A-14A-13

ORDINARY SEWING

Insert the twin needle.

Follow the instructions for single-needle threading using the horizontal spool pin. Thread through the left needle.

Set the second spool pin into the hole on the top of the machine. Thread through remaining points, making certain to omit the thread guide above the needle and pass thread through the right needle.

Thread each needle separately.

Please Note:

Make sure that the two threads used to thread the twin needle are of the same weight. You can use one or two colors.

* The twin needle is optional. It is not incl ude

with the accessories.

Attention:

When using twin needles, use the all purpose foot (T) regardless of what kind of sewing foot will be carried out.

Use only twin needle assemblies with max. 2mm needle distance.

2.0~5.0

Select a stitch pattern. (e.g. A group pattern 13) Except the Direct Pattern 0 and Patterns 86-98

from Group Pattern "A", the other patterns can be used.

Using the twin needle

ORDINARY SEWING

Press the twin needle button " ". The LCD screen will display the twin needle

icon " " and the machine automatically reduces the maximum width for twin needle sewing by 2mm.

Please Note:

- When sewing with twin needle, always

proceed slowly, and make sure to maintain a low speed to insure quality stitching.

- When double needle sewing has been

selected, it will remain active even the stitch pattern is changed. To deactivate double needle sewing press the double needle button again.

Two lines of stitching are sewn parallel to each other.

ORDINARY SEWING

Combined patterns can be stored for later use. Since stored patterns are not lost after the sewing machine is turned off, they can be recalled at any time. This is convenient for patterns, such as names, that will be used often.

Please Note:

- Multiple patterns selecting from pattern groups,,,canbecombined together.

- Direct Patterns 0 and cannot be entered into memory.

- This machine has 4 modules of program memory and each module can retain 20 units of stitches.

- All the units in the memory can be edited to set its function such as Stitch length, Stitch width, Elongation, Mirror, and Auto-lock.

Patterns 86-98 from Group Pattern "A"

1. Press the memory button to enter the memory mode. If you want to leave the memory module screen, press the

clear/ return button to return the normal screen.

Combining patterns

2. Use the arrow buttons to select the number of the memory module. (For example: M3)

3. Press the OK button,

Upper left corner of LCD screen shows the number of the memory module.

The memory screen is entered automatically and the flashing cursor is in position for the first pattern to be entered.

To store the combination of characters or decorative stitches.

Memory

5. Press the OK button to into pattern browser, the display containing the various stitches in the selected pattern group appears.

6. Press the desired pattern number or the arrow buttons to select desired pattern. ( A group pattern 36)

The selected pattern displays on the LCD display and the cursor moves to the next position.

For example:

7. Repeat step 4~6 for more patterns to be stored in the memory. When 20 patterns have been selected, the memory will be

full. If another pattern is selected after the memory is full the machine will beep to prompt it.

4. Press the pattern group selection button to enter the pattern

group selection display.

(E.g. For pattern group "A")

Select the desired pattern group.

8. Press the memory button to leave the memory mode and return to the normal mode.

Attention:

The selected pattern will be cleared from the memory module after closing the machine if you do not press

again when you have completed your selection.

the memory

button

ORDINARY SEWING

Editing patterns

1. Press the memory button to enter the memory mode.

2. Use the arrow buttons to select the number of the memory module. (For example: M3)

3. Press the OK button, the LCD screen containing the various types of stitches will open and the cursor stay in 1st position.

4. Use the arrow buttons to select the pattern that you wish to edit while in the memory mode.

The stitch length, stitch width, Elongation, Mirror imaging and Auto-lock of the patterns can be adjusted.

ORDINARY SEWING

Clearing patterns

1. Use the arrow buttons to move the cursor to the pattern that you want to delete.

2. Press the clear/ return button to delete the selected pattern and all patterns in the back will be moved one memory position forward.

Adding patterns

1. Use the arrow buttons to move the cursor to the pattern that you want to delete.

2. Press the desired pattern number or the arrow buttons to select desired pattern. (E.g. B group pattern 54)

All patterns in the back will be moved one memory position backward.

ORDINARY SEWING

Recalling and sewing the memorized pattern

1. Press the memory button to enter the memory mode.

2. Use the arrow buttons to select the number of the memory module. (For example: M3)

3. Press the OK button, the LCD screen containing the various types of stitches will open.

4. Press the start/stop button or step on the foot controller to start the sewing.

The cursor on the LCD screen will move along with the sequential pattern while sewing.

5. Press the memory button to leave the memory mode and return to the normal mode.

Please Note:

- If the cursor stays in a vacant position in the end, the

machine will start sewing from the first pattern.

- If the cursor stays under a specific pattern, the machine will

start sewing from that pattern.

APPENDIX

Warning message

Presser foot is not ready for sewing

This message is displayed when the Start/stop button or

button is pressed while the presser

foot is raised.

the

needle up/down position

BH lever is not lowered

he buttonhole or darning stitch was selected and the start/stop button was pressed while the buttonhole lever is raised.

This message is displayed when t

BH lever is not lifted

stitch other than the buttonhole or darning stitch was selected and the start/stop button was pressed while the buttonhole lever is down.

This message is displayed when the

Bobbin thread is low

This message is displayed when the bobbin thread is running out.

The upper thread is broken

This message is displayed when the upper thread is broken. Please check and rethread the upper thread.

Bobbin winding

This message is displayed when the bobbin winder is winding the bobbin.

The sewing machine is in trouble

The animation message means that the thread is twisted or jammed and the hand wheel axle cannot move.

Please look through the "Trouble shooting guide" to find the solution. After the problem has been solved, the machine will continue to sew.

Warning functions

APPENDIX

Warning sound

- When operating correctly: 1 beep

- When the memory is full with 20 units of pattern: 3-short

beeps

- When operating incorrectly: 3-short beeps

- When the sewing machine is in trouble and can't sew: 3-short

beeps It means that the thread is twisted or jammed and the hand

wheel axle can't move. Please look through the "Trouble shooting guide" to find the solution. After the problem has been solved, the machine will continue to sew.

Please Note:

If the problem is still not solved, please contact your local dealer.

Attention:

During the sewing, if the thread get jammed inside the hook stopping the needle from moving and you continue pressing the foot control, the security switch will stop the machine completely.

In order to restart the sewing machine, you will have to turn the on/off switch to the OFF position and then ON again.

APPENDIX

Buzzer sound

Hold on the button and turn on the power switch.

The buzzer sound can be set on/ off by pressing the arrow buttons .

Pressing the OK button . The Buzzer sound setting mark will appear on the LCD screen

when you have set it.

Sound off

Sound on

APPENDIX

Attention:

Disconnect the power cord from the wall socket before cleaning the screen and sewing machine surface, otherwise injury or electrical shock may result.

Remove the needle plate cover and bobbin.

If lint and bits of thread accumulate in the hook, this will interfere with the smooth operation of the machine. Check regularly and clean the stitching mechanism when necessary.

If the front panel is dirty, wipe it gently with a soft, dry cloth. Do not use any organic solvents or detergents.

Cleaning the screen

If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out firmly and then wipe the surface. After cleaning it once in this way, wipe the surface again with a dry cloth.

Cleaning the sewing machine surface

Cleaning the hook

Attention:

Disconnect the machine from the wall outlet before carrying out any maintenance.

Attention:

This machine is equipped with a 100mW LED lamp. If lamp replacement is needed, please contact nearest

authorized retailer.

Maintenance

APPENDIX

Clean the bobbin holder with a brush.

Remove the needle, presser foot and presser foot holder. Remove the screw holding the needle plate and remove the

needle plate.

Clean the feed dog and bobbin case with a brush. Also clean them, using a soft, dry cloth.

APPENDIX

Problem

Cause

Correction

Upper thread

breaks

Lower thread

breaks

Skipped

stitches

Needle

breaks

Loose

stitches

1. The machine is not threaded correctly.

2. The thread tension is too tight.

3. The thread is too thick for the needle.

4. The needle is not inserted correctly.

5. The thread is wound around the spool holder pin.

6. The needle is damaged.

1. The bobbin case is not inserted correctly.

2. The bobbin case is threaded wrong.

1. The needle is not inserted correctly.

2. The needle is damaged.

3. The wrong size needle has been used.

4. The foot is not attached correctly.

5. The machine is not threaded correctly.

1. The needle is damaged.

2. The needle is not correctly inserted.

3. Wrong needle size for the fabric.

4. The wrong foot is attached.

5. The needle clamp screw is loose.

6. The presser foot that is used is not appropriate for the type of stitch that you wish to sew.

7. The upper thread tension is too tight.

1. The machine is not correctly threaded.

2. The bobbin case is not correctly

3. Needle/ fabric/ thread combination is wrong.

4. Thread tension is wrong.

1. Check the threading.

2. Thread the bobbin case as illustrated.

3. The needle size must suit the fabric and thread.

4. Correct the thread tension.

1. Insert a new needle.

2. Insert the needle correctly (flat side towards the back).

3. Choose a needle to suit the thread and fabric.

4. Select the correct foot.

5. Use the screwdriver to firmly tighten the screw.

6. Attach the presser foot that is appropriate for the type of stitch that you wish to sew.

7. Loosen the upper thread tension.

1. Remove and reinsert needle (flat side towards the back).

2. Insert a new needle.

3. Choose a needle to suit the thread.

4. Check and attach correctly.

5. Rethread the machine.

1. Remove and reinsert the bobbin case and pull on the thread. The thread should pull easily.

2. Check both bobbin and bobbin case.

1. Rethread the machine.

2. Reduce the thread tension (lower number).

3. Select a larger needle.

4. Remove and reinsert the needle (flat side towards the back).

5. Remove the reel and wind thread onto reel.

6. Replace the needle.

Reference

Before calling for service, check the following items. If the problem still persists, contact the place of purchase or your nearest authorized dealer.

Trouble shooting guide

Problem

Cause

Correction

Reference

Seam

puckering

Patterns are

distorted

1. The needle thread tension is too tight.

2. The needle thread is not threaded correctly.

3. The needle is too heavy for the fabric being sewn.

4. The stitch length is too long for the fabric.

1. The correct presser foot is not used.

2. The needle thread tension is too tight.

1. Select the correct foot.

2. Loosen the thread tension .

1. Lossen the thread tension.

2. Rethread the machine.

3. Choose a needle to suit the thread and fabric.

4. Make stitch dense.

The sewing

machine

doesn't

operate

1. The machine is not turned on.

2. The presser foot lifter is raised.

1. Turn on the machine.

2. Lower the presser foot lifter.

The

machine

jams

Remove the upper thread and bobbin case, turn the hand wheel backwards and forwards by hand and remove the thread remands.

The

machine is

noisy

1. Fluff or oil have collected on the hook or needle bar.

2. The needle is damaged.

1. Clean the hook and feed dog as described.

2. Replace the needle.

Uneven

stitches,

uneven feed

1. Poor quality thread.

2. The bobbin case is threaded wrong.

3. Fabric has been pulled.

1. Select a better quality thread.

2. Remove the bobbin case, the thread and reinsert correctly.

3. Do not pull on the fabric while sewing, let it be taken up by the machine.

4. Thread is caught in the hook.

3. Slight humming sound coming from internal motor.

3. Normal.

5. The feed dogs are packed with lint.

Remove the upper thread and bobbin case, turn the hand wheel backwards and forwards by hand and remove the thread remands.

1. Thread is caught in the hook.

2. The feed dogs are packed with lint.

3. Connect the power line plug to the electric outlet.

3. The machine is not plugged in.

Seam

gather or

pucker

1. The needle is too thick for the fabric.

2. The stitch length is adjusted wrong.

3. The thread tension is too tight.

1. Select a finer needle.

2. Readjust the stitch length.

3. Loosen the thread tension.

5. If you are sewing thin fabric. 5. Sew with stabiliser material under the fabric.

APPENDIX

021H4B0107(EN)

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new once, the retailer is legally obligated to take back your old

appliance for disposal at least for free of charge.

MOOD Lia H40B Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual