montpellier CT750, CT905 Installation And Operating Instructions Manual

CT750 & CT905
70/90cm - 99min Timer
1. Please check the built-in ceramic hob's integrity after opening the package. If there are any problems please refer to the supplier.
2. Do not throw the package materials (plastic bag, foam, nails, package etc) in a place where children can easily access. Please dispose of packaging in an environmentally friendly manner.
3. Do not change the wiring under any circumstances.
4. Dispose of the appliance in an environmentally friendly manner.
6. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
7. Children should be supervised to ensure that they do not play with the appliance.Cleaning and user maintenance shall not be made by children without supervision.
8. Do not stare at the hob elements when the appliance is working.
9. Accessible parts may become hot during use. To avoid burns young children should be kept away
10. WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock, for hob surfaces of glass-ceramic or similar material which protect live parts
11.Shall state a steam cleaner is not be used.
12.Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
13. CAUTION: The surface temperature exceeds 95°C.To avoid a hazard,under bench access must be restricted.Refer to the installation instructions.
14. WARNING:The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.Children less than 8 years of age shall be kept away unless continuously supervised.
15.The appliance is not intended to be operated by means of an external timer or separate remote-control system.
16. WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
17. WARNING: Danger of fire: do not store items on the cooking surfaces.
18. CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously.
19.WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.
A duplicate data label and wiring diagram are contained in this booklet.Please attach these labels to an accessible and near by surface for easy reference. The Manufacturer shall not be held responsible for any innaccuracies in this handbook due to printing or transcription errors,also the designs in the figures are purely indicative. The Manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful also in the interests of the user, without jeopardizing the main functional and safety features of the products themselves.
Heating area
(Φ145mm)
Heating area
(Φ120mm)
Heating area
(Φ180mm)
Heating area
(Φ180mm)
Heating area
(Φ145mm)
Heating area
(Φ120mm)
Heating area
(Φ180mm)
Heating area
(Φ180mm)
Heating area
(Φ180mm)
Heating area
(Φ145mm)
Heating area
(Φ180mm)
CT750 CT905
Heating area
(Φ145mm)
Switching off the ceramic hob
1. Press the ON/OFF button, the hob will switch off. It is possible to turn the hob off at any time by pressing the ON/OFF button.
2. Press the up or down buttons to 0, then hob will switch off. After a zone is switched off, the corresponding heat level display will show a flashing letter “H” . This means that the temperature of the zone is above 60°C and is therefore still high enough to cause injury.
When the temperature of the zone falls below 60°C the letter “H” will go out. It is still possible to burn yourself on a hob zone, even when its temperature has dropped below 60°C.
IMPORTANT: The residual heat indicator will disappear if the mains supply to the product is cut.
Locking the ceramic hob
To lock the ceramic hob, press the safety lock button (fig. 4) while the appliance is switched on. With the safety lock activated, all buttons on the control panel will be disabled, except the ON/OFF button. To disable the safety lock feature, press the safety lock button again. And you are then able to adjust the heat level of any zone on the hob.
fig.3
Timer
Your hob has a timer which you can set (from 1 to 99 minutes) for each cooking zone. At the end of the countdown period, a buzzer will sound and the relevant cooking zone will be switched off.
Select the cooking zone (fig. 2) and heat level (fig. 3).
Press the timer button (fig. 5), and then use the up and down buttons to set the countdown time.
Each time the timer up or down button is pressed, the timer display will increase or decrease in 1
minute increments.
Safety cut-off
If one or more of the cooking zones are accidentally left on, a safety cut-off will activate after a certain period of time. The length of time depends on the set power level for that zone. The table on the right gives the time limits for each power level.
If more than one zone is operating when one of the zones reaches its safety cut-off point, only the zone that has reached its safety cut-off point will switch off.
Power level 16263545546
Time limit (hours)
1.571.581.591.5
fig.4
fig.5
DUAL COOKING ZONE
Open the DUAL COOKING ZONE ,the inner ring is working, press the DUAL COOKING button (fig. 6), the outer ring is working.
3.
fig.6
Technical Data
Model
CT750
CT905
Power Supply
AC220-240V
50Hz
Power(W)
(180mm)(145mm) (180mm/120mm)
1200W 1800W 1700W/700W
1200W 1800W 1700W/700W
Size (mm)
750X510X77 735X490
860X520X77 830X490
Buit-in Hole Size
(mm)
Good Bad
(recessed base) (convex base) (undersize) (oversize) (moisture on hotplate) (no utensil)
Bad Bad Bad Bad Bad
CONNECTION DIAGRAM
Caution! Voltage of heating
elements 220-240V Caution! In the event
of any connection the safety Wire
must be connected to the E terminal.
Recommended type of
connection lead
For 220-240V earthed one-phase connection, bridges connect L①-②-③ terminals andN④-⑤ terminals, safety
wire to
L
N
E
If the cable is damaged or to be replaced, the operation must be carried out the by a service agent or a suitably qualified professional.
If the appliance is being connected directly to the mains, an omnipolar circuit breaker must be installed with a minimum opening of 3mm between contacts.
The installer must ensure that the correct electrical connection has been made and that it is compliant with all applicable standards and safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorised technicians only.
450
WARNING
Close the cable clamp after making the electrical connection. Close the terminal
board cover by twisting it down.
77
750
72
490
735
CT750
510
750
450
TERMINAL BOARD
860
77
72
490
830
520
750
50mm MIN.
Ventilation slot ≥ mm:30
Heat outlet
15mm MIN.
Wood block
Recommended installation
CT905
Rear wall
200
Front edge of worktop
200
50
50
4
5
screw
1-worktop 2-screw
OR
bracket
3-bracket 4-hob 5-hob seal
2
1
3
CT905
screw hold
CT750
S
Hob
Worktop
Screw
Fixing bracket
Screw
Scraper for cleaning the hob
Disassembly bottom base
4 bigger screws need to be removed first before bottom base disassembly. (Bottom base removal need to be done by professional person. Normal user is not allowed to disassembly bottom base)
Screws need to removed
MALFUNCTION ELIMINATION
Malfunction
Hob doesn't work
There is some smoke when it is working
The wire is damaged
Erp
Eliminating guide
•Check the connection of wires
•Check the fuse and the current limit
•It is normal the first time you use.
•Clean the drail around the hob and the heating area.
•Connect the nearest maintainance center to change the equipment parts.
This appliance is labelled in compliance with European directive 2012/19/EC for Waste Electrical and Electronic
Equipment (WEEE). By ensuring that this appliance is disposed of correctly, you will help prevent any possible harm
to the environment and to human health which might otherwise be caused if disposed of in the wrong way.
The symbol on the product indicates that it may not be treated as normal household waste.
It should be taken to a collection point for the recycling of electrical and electronic goods.
This appliance requires specialist waste disposal. For further information regarding the treatment, recovery and
recycling of this product, please contact your local council, household waste disposal service or the shop where you
For more detailed information about treatment, recovery and recycling of this product, please contact your local local
council, household waste disposal service or the shop where you purchased the product.
Symbol
purchased the product.
Value
Unit
Model identification
Type of hob
Number of electric cooking
zones and/or areas
Heating technology (induction cooking zones and cooking areas, radiant cooking zones, solid plates)
For circular cooking zones or area: diameter of useful surface area per electric heated cooking zone, rounded to the nearest 5 mm
For non-circular cooking zones or areas: length and width of useful surface area per electric heated cooking zone or area, rounded to the nearest 5 mm
Energy consumption per cooking zone or area calculated per kg
EC
electric cooking
--
--
--
--
Ø
L, W
CT750 CT905
Built-in hob
5 5
Radiant cooking
zones
Big ring: 18.0 cm Small ring: 14.5 cm
Multiple zones: outer ring: 18.0 cm, inner ring: 12.0 cm
N/A N/A
Big ring: 194 Small ring: 187 Multiple zones: 195
Built-in hob
Radiant cooking
zones
Big ring: 18.0 cm Small ring: 14.5 cm
Multiple zones: outer ring: 18.0 cm, inner ring: 12.0 cm
Big ring: 194 Small ring: 187 Multiple zones: 195
cm
cm
Wh/kg
Energy consumption for the hob calculated per kg
EC
electric hob
7.
190190
Wh/kg
01759 487839
Repair costs incurred that have not been authorised by Montpellier and/or carried out by a non-approved
Montpellier engineer.
01759 487839
Loading...